Skip to main content
La version française est une traduction automatique. La version anglaise prévaut sur la française en cas de divergence.

Installez ou mettez à niveau le logiciel NX-OS

Contributeurs netapp-yvonneo
PDF

Suivez cette procédure pour installer ou mettre à niveau le logiciel NX-OS sur le commutateur Nexus 9332D-GX2B.

Exigences de révision

Avant de commencer

Vérifiez les éléments suivants :

  • Terminez la procédure dans"Préparez-vous à installer NX-OS et RCF" .

  • Une sauvegarde actuelle de la configuration du commutateur.

  • Un cluster parfaitement fonctionnel (aucune erreur dans les journaux ni problème similaire).

Documentation suggérée
À propos des exemples

Les exemples de cette procédure utilisent la nomenclature suivante pour les commutateurs et les nœuds :

  • Les noms des deux commutateurs Cisco sont cs1 et cs2.

  • Les noms des nœuds sont node1-01, node1-02, node1-03 et node1-04.

  • Les noms LIF du cluster sont node1-01_clus1, node1-01_clus2, node1-02_clus1, node1-02_clus2, node1-03_clus1, node1-03_clus2, node1-04_clus1 et node1-04_clus2.

  • Le cluster1::*> L'invite indique le nom du cluster.

Installez le logiciel

La procédure nécessite l'utilisation des commandes ONTAP et des commandes des commutateurs Cisco Nexus série 9000 ; les commandes ONTAP sont utilisées sauf indication contraire.

Important

  • NX-OS 10.4.2 est la seule version prise en charge pour les commutateurs Cisco Nexus 9332D-GX2B dans un cluster ONTAP .

  • Ne mettez pas à niveau ou ne rétrogradez pas votre version NX-OS vers une version non prise en charge ; seule la version 10.4.2 est actuellement prise en charge.
Étapes

  1. Connectez le commutateur au réseau de gestion.

  2. Utilisez la commande ping pour vérifier la connectivité au serveur hébergeant le logiciel NX-OS et le RCF.

    Afficher un exemple

    Cet exemple vérifie que le commutateur peut atteindre le serveur à l'adresse IP 172.19.2.1 :

    cs2# ping 172.19.2.1
Pinging 172.19.2.1 with 0 bytes of data:

Reply From 172.19.2.1: icmp_seq = 0. time= 5910 usec.

  3. Afficher les ports du cluster sur chaque nœud qui sont connectés aux commutateurs du cluster :

    network device-discovery show
    Afficher un exemple 
    cluster1::*> network device-discovery show

Node/       Local  Discovered
Protocol    Port   Device (LLDP: ChassisID) Interface         Platform
----------- ------ ------------------------ ----------------  ----------------
node1-01/cdp
            e10a   cs1(FLMXXXXXXXX)         Ethernet1/16/3    N9K-C9332D-GX2B
            e10b   cs2(FDOXXXXXXXX)         Ethernet1/16/3    N9K-C9332D-GX2B
            e11a   cs1(FLMXXXXXXXX)         Ethernet1/16/4    N9K-C9332D-GX2B
            e11b   cs2(FDOXXXXXXXX)         Ethernet1/16/4    N9K-C9332D-GX2B
            e1a    cs1(FLMXXXXXXXX)         Ethernet1/16/1    N9K-C9332D-GX2B
            e1b    cs2(FDOXXXXXXXX)         Ethernet1/16/1    N9K-C9332D-GX2B
            .
            .
            .
            e7a    cs1(FLMXXXXXXXX)         Ethernet1/16/2    N9K-C9332D-GX2B
            e7b    cs2(FDOXXXXXXXX)         Ethernet1/16/2    N9K-C9332D-GX2B

node1-01/lldp
            e10a   cs1 (c8:60:8f:xx:xx:xx)  Ethernet1/16/3    -
            e10b   cs2 (04:e3:87:xx:xx:xx)  Ethernet1/16/3    -
            e11a   cs1 (c8:60:8f:xx:xx:xx)  Ethernet1/16/4    -
            e11b   cs2 (04:e3:87:xx:xx:xx)  Ethernet1/16/4    -
            e1a    cs1 (c8:60:8f:xx:xx:xx)  Ethernet1/16/1    -
            e1b    cs2 (04:e3:87:xx:xx:xx)  Ethernet1/16/1    -
            .
            .
            .
            e7a    cs1 (c8:60:8f:34:78:d3)  Ethernet1/16/2    -
            e7b    cs2 (04:e3:87:19:a2:59)  Ethernet1/16/2    -
.
.
.

  4. Vérifiez le statut administratif et opérationnel de chaque port.

    1. Ports de cluster

      1. Vérifiez que tous les ports du cluster sont opérationnels et en bon état :

        network port show -ipspace Cluster
        Afficher un exemple 
        cluster1::*> network port show -ipspace Cluster

Node: node1-01
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/100000 healthy false
e7b       Cluster      Cluster          up   9000  auto/100000 healthy false

Node: node1-02
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/100000 healthy false
e7b       Cluster      Cluster          up   9000  auto/100000 healthy false

Node: node1-03

                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/10000 healthy  false
e7b       Cluster      Cluster          up   9000  auto/10000 healthy  false

Node: node1-04
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/10000 healthy  false
e7b       Cluster      Cluster          up   9000  auto/10000 healthy  false

      2. Vérifiez que toutes les interfaces du cluster (LIF) sont connectées au port d'accueil :

        network interface show -role cluster
        Afficher un exemple 
        cluster1::*> network interface show -role cluster

            Logical         Status     Network            Current   Current Is
Vserver     Interface       Admin/Oper Address/Mask       Node      Port    Home
----------- --------------- ---------- ------------------ --------- ------- ----
Cluster
            node1-01_clus1  up/up      169.254.36.44/16   node1-01  e7a     true
            node1-01_clus2  up/up      169.254.7.5/16     node1-01  e7b     true
            node1-02_clus1  up/up      169.254.197.206/16 node1-02  e7a     true
            node1-02_clus2  up/up      169.254.195.186/16 node1-02  e7b     true
            node1-03_clus1  up/up      169.254.192.49/16  node1-03  e7a     true
            node1-03_clus2  up/up      169.254.182.76/16  node1-03  e7b     true
            node1-04_clus1  up/up      169.254.59.49/16   node1-04  e7a     true
            node1-04_clus2  up/up      169.254.62.244/16  node1-04  e7b     true

8 entries were displayed.

      3. Vérifiez que le cluster affiche les informations pour les deux commutateurs du cluster :

        system cluster-switch show -is-monitoring-enabled-operational true
        Afficher un exemple 
        cluster1::*> system cluster-switch show -is-monitoring-enabled-operational true

Switch                      Type               Address          Model
--------------------------- ------------------ ---------------- ---------------
cs2(FDOXXXXXXXX)            cluster-network    10.228.137.233   N9K-C9332D-GX2B
     Serial Number: FDOXXXXXXXX
      Is Monitored: true
            Reason: None
  Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                    10.4(2)
    Version Source: CDP/ISDP


cs1(FLMXXXXXXXX)             cluster-network   10.228.137.253   N9K-C9332D-GX2B
     Serial Number: FLMXXXXXXXX
      Is Monitored: true
            Reason: None
  Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                    10.4(2)
    Version Source: CDP/ISDP

2 entries were displayed.

    2. Ports HA

      1. Vérifiez que tous les ports HA sont opérationnels et en bon état :

        ha interconnect status show -node <node-name>

    Afficher un exemple 
    cluster1::*> ha interconnect status show -node node1-01
  (system ha interconnect status show)

                       Node: node1-01
              Link 0 Status: up
              Link 1 Status: up
           Is Link 0 Active: true
           Is Link 1 Active: true
         IC RDMA Connection: up
                       Slot: 0
             Debug Firmware: no


Interconnect Port 0 :
                  Port Name: e1a-17
                        MTU: 4096
           Link Information: ACTIVE


Interconnect Port 1 :
                  Port Name: e1b-18
                        MTU: 4096
           Link Information: ACTIVE

cluster1::*> ha interconnect status show -node node1-02
  (system ha interconnect status show)

                       Node: node1-02
              Link 0 Status: up
              Link 1 Status: up
           Is Link 0 Active: true
           Is Link 1 Active: true
         IC RDMA Connection: up
                       Slot: 0
             Debug Firmware: no


Interconnect Port 0 :
                  Port Name: e1a-17
                        MTU: 4096
           Link Information: ACTIVE


Interconnect Port 1 :
                  Port Name: e1b-18
                        MTU: 4096
           Link Information: ACTIVE
.
.
.

    1. Ports de stockage

      1. Vérifiez que tous les ports de stockage sont opérationnels et en bon état :

        storage port show -port-type ENET
        Afficher un exemple 
        cluster1::*> storage port show -port-type ENET


                                      Speed
Node               Port Type  Mode    (Gb/s) State    Status
------------------ ---- ----- ------- ------ -------- -----------
node1-01
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
                   e11b ENET  -          100 enabled  online
node1-02
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
                   e11b ENET  -          100 enabled  online
node1-03
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
node1-04
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
                   e11b ENET  -          100 enabled  online
16 entries were displayed.

    2. Ports d'étagères de stockage

      1. Vérifiez que tous les ports de l'étagère de stockage sont opérationnels et en bon état :

        storage shelf port show
        Afficher un exemple 
        cluster1::*> storage shelf port show

Shelf ID Module State        Internal?
----- -- ------ ------------ ---------
1.1
       0 A      connected    false
       1 A      connected    false
       2 A      connected    false
       3 A      connected    false
       4 A      connected    false
       5 A      connected    false
       6 A      connected    false
       7 A      connected    false
       8 B      connected    false
       9 B      connected    false
      10 B      connected    false
      11 B      connected    false
      12 B      connected    false
      13 B      connected    false
      14 B      connected    false
      15 B      connected    false

16 entries were displayed.

      2. Vérifiez l’état de connexion de tous les ports de l’étagère de stockage :

        storage shelf port show -fields remote-device,remote-port,connector-state
        Afficher un exemple 
        cluster1::*> storage shelf port show -fields remote-device,remote-port,connector-state

shelf id connector-state remote-port    remote-device
----- -- --------------- -------------- -----------------
1.1   0  connected       Ethernet1/17/1 CX9332D-cs1
1.1   1  connected       Ethernet1/15/1 CX9364D-cs1
1.1   2  connected       Ethernet1/17/2 CX9332D-cs1
1.1   3  connected       Ethernet1/15/2 CX9364D-cs1
1.1   4  connected       Ethernet1/17/3 CX9332D-cs1
1.1   5  connected       Ethernet1/15/3 CX9364D-cs1
1.1   6  connected       Ethernet1/17/4 CX9332D-cs1
1.1   7  connected       Ethernet1/15/4 CX9364D-cs1
1.1   8  connected       Ethernet1/19/1 CX9332D-cs1
1.1   9  connected       Ethernet1/17/1 CX9364D-cs1
1.1   10 connected       Ethernet1/19/2 CX9332D-cs1
1.1   11 connected       Ethernet1/17/2 CX9364D-cs1
1.1   12 connected       Ethernet1/19/3 CX9332D-cs1
1.1   13 connected       Ethernet1/17/3 CX9364D-cs1
1.1   14 connected       Ethernet1/19/4 CX9332D-cs1
1.1   15 connected       Ethernet1/17/4 CX9364D-cs1

16 entries were displayed.

  5. Désactiver la restauration automatique sur les LIF du cluster. Les LIF du cluster basculent vers le commutateur du cluster partenaire et y restent pendant que vous effectuez la procédure de mise à niveau sur le commutateur cible :

    network interface modify -vserver Cluster -lif * -auto-revert false

  6. Copiez le logiciel NX-OS et les images EPLD sur le commutateur Nexus 9332D-GX2B.

    Afficher un exemple 
    cs2# copy sftp: bootflash: vrf management
Enter source filename: /code/nxos.10.4.2.bin
Enter hostname for the sftp server: 172.19.2.1
Enter username: root

Outbound-ReKey for 172.19.2.1:22
Inbound-ReKey for 172.19.2.1:22
root@172.19.2.1's password:
sftp> progress
Progress meter enabled
sftp> get   /code/nxos.10.4.2.bin  /bootflash/nxos.10.4.2.bin
/code/nxos.10.4.2.bin  100% 1261MB   9.3MB/s   02:15
sftp> exit
Copy complete, now saving to disk (please wait)...
Copy complete.

cs2# copy sftp: bootflash: vrf management
Enter source filename: /code/n9000-epld.10.4.2.F.img
Enter hostname for the sftp server: 172.19.2.1
Enter username: user1

Outbound-ReKey for 172.19.2.1:22
Inbound-ReKey for 172.19.2.1:22
user1@172.19.2.1's password:
sftp> progress
Progress meter enabled
sftp> get   /code/n9000-epld.10.4.2.F.img  /bootflash/n9000-epld.10.4.2.F.img
/code/n9000-epld.10.4.2.F.img  100%  161MB   9.5MB/s   00:16
sftp> exit
Copy complete, now saving to disk (please wait)...
Copy complete.

  7. Vérifiez la version du logiciel NX-OS en cours d'exécution :

    show version

    Afficher un exemple 
    cs2# show version
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (C) 2002-2025, Cisco and/or its affiliates.
All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under their own
licenses, such as open source.  This software is provided "as is," and unless
otherwise stated, there is no warranty, express or implied, including but not
limited to warranties of merchantability and fitness for a particular purpose.
Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or
GNU General Public License (GPL) version 3.0  or the GNU
Lesser General Public License (LGPL) Version 2.1 or
Lesser General Public License (LGPL) Version 2.0.
A copy of each such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://opensource.org/licenses/gpl-3.0.html and
http://www.opensource.org/licenses/lgpl-2.1.php and
http://www.gnu.org/licenses/old-licenses/library.txt.


Software
  BIOS: version 01.14
  NXOS: version 10.4(1) [Feature Release]
  Host NXOS: version 10.4(1)
  BIOS compile time:  11/25/2024
  NXOS image file is: bootflash:///nxos64-cs.10.4.1.F.bin
  NXOS compile time:  11/30/2023 12:00:00 [12/14/2023 05:25:50]
  NXOS boot mode: LXC


Hardware
  cisco Nexus9000 C9332D-GX2B Chassis
  Intel(R) Xeon(R) CPU D-1633N @ 2.50GHz with 32802156 kB of memory.
  Processor Board ID FLMXXXXXXXX
  Device name: cs2
  bootflash:  115802886 kB


Kernel uptime is 5 day(s), 2 hour(s), 13 minute(s), 21 second(s)


Last reset at 3580 usecs after Thu Jun  5 15:55:08 2025
  Reason: Reset Requested by CLI command reload
  System version: 10.4(1)
  Service:


plugin
  Core Plugin, Ethernet Plugin


Active Package(s):

cs2#

  8. Installez l'image NX-OS.

    L'installation du fichier image entraîne son chargement à chaque redémarrage du commutateur.

    Afficher un exemple 
    cs2# install all nxos bootflash:nxos.10.4.2.bin

Installer will perform compatibility check first. Please wait.
Installer is forced disruptive

Verifying image bootflash:/nxos.10.4.2.bin for boot variable "nxos".
[] 100% -- SUCCESS

Verifying image type.
[] 100% -- SUCCESS

Preparing "nxos" version info using image bootflash:/nxos.10.4.2.bin.
[] 100% -- SUCCESS

Preparing "bios" version info using image bootflash:/nxos.10.4.2.bin.
[] 100% -- SUCCESS

Performing module support checks.
[] 100% -- SUCCESS

Notifying services about system upgrade.
[] 100% -- SUCCESS


Compatibility check is done:
Module  Bootable  Impact          Install-type  Reason
------  --------  --------------- ------------  ---------
  1     yes       Disruptive      Reset         Default upgrade is not hitless



Images will be upgraded according to following table:

Module   Image    Running-Version(pri:alt)                 New-Version         Upg-Required
------- --------- ---------------------------------------- ------------------- ------------
  1      nxos     10.4(1)                                  10.4(2)             Yes
  1      bios     xx.xx.:xx.xx                             xxx                 No


Switch will be reloaded for disruptive upgrade.

Do you want to continue with the installation (y/n)? [n] y

Install is in progress, please wait.

Performing runtime checks.
[] 100% -- SUCCESS

Setting boot variables.
[] 100% -- SUCCESS

Performing configuration copy.
[] 100% -- SUCCESS

Module 1: Refreshing compact flash and upgrading bios/loader/bootrom.
Warning: please do not remove or power off the module at this time.
[] 100% -- SUCCESS

Finishing the upgrade, switch will reboot in 10 seconds.

  9. Vérifiez la nouvelle version du logiciel NX-OS après le redémarrage du commutateur :

    show version

    Afficher un exemple 
    cs2# show version
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (C) 2002-2025, Cisco and/or its affiliates.
All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under their own
licenses, such as open source.  This software is provided "as is," and unless
otherwise stated, there is no warranty, express or implied, including but not
limited to warranties of merchantability and fitness for a particular purpose.
Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or
GNU General Public License (GPL) version 3.0  or the GNU
Lesser General Public License (LGPL) Version 2.1 or
Lesser General Public License (LGPL) Version 2.0.
A copy of each such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://opensource.org/licenses/gpl-3.0.html and
http://www.opensource.org/licenses/lgpl-2.1.php and
http://www.gnu.org/licenses/old-licenses/library.txt.


Software
  BIOS: version 01.14
  NXOS: version 10.4(2) [Feature Release]
  Host NXOS: version 10.4(2)
  BIOS compile time:  11/25/2024
  NXOS image file is: bootflash:///nxos64-cs.10.4.2.F.bin
  NXOS compile time:  11/30/2023 12:00:00 [12/14/2023 05:25:50]
  NXOS boot mode: LXC


Hardware
  cisco Nexus9000 C9332D-GX2B Chassis
  Intel(R) Xeon(R) CPU D-1633N @ 2.50GHz with 32802156 kB of memory.
  Processor Board ID FLMXXXXXXXX
  Device name: cs2
  bootflash:  115802886 kB


Kernel uptime is 5 day(s), 2 hour(s), 13 minute(s), 21 second(s)


Last reset at 3580 usecs after Thu Jun  5 15:55:08 2025
  Reason: Reset Requested by CLI command reload
  System version: 10.4(2)
  Service:


plugin
  Core Plugin, Ethernet Plugin


Active Package(s):

cs2#

  10. Mettez à jour l'image EPLD et redémarrez le commutateur.

    Afficher un exemple 
    cs2# show version module 1 epld

EPLD Device                     Version
---------------------------------------
MI   FPGA                        0x7
IO   FPGA                        0x17
MI   FPGA2                       0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2

cs2# install epld bootflash:n9000-epld.10.4.2.F.img module all
Compatibility check:
Module        Type         Upgradable        Impact    Reason
------  ------------------ ----------------- --------- -----------
     1         SUP         Yes       disruptive  Module Upgradable

Retrieving EPLD versions.... Please wait.
Images will be upgraded according to following table:
Module  Type   EPLD              Running-Version   New-Version  Upg-Required
------- ------ ----------------- ----------------- ------------ ------------
     1  SUP    MI FPGA           0x07              0x07         No
     1  SUP    IO FPGA           0x17              0x19         Yes
     1  SUP    MI FPGA2          0x02              0x02         No
The above modules require upgrade.
The switch will be reloaded at the end of the upgrade
Do you want to continue (y/n) ?  [n] y

Proceeding to upgrade Modules.

Starting Module 1 EPLD Upgrade

Module 1 : IO FPGA [Programming] : 100.00% (     64 of      64 sectors)
Module 1 EPLD upgrade is successful.
Module   Type  Upgrade-Result
-------- ----- --------------
     1   SUP   Success

EPLDs upgraded.

Module 1 EPLD upgrade is successful.

  11. Après le redémarrage du commutateur, reconnectez-vous et vérifiez que la nouvelle version d'EPLD a bien été chargée.

    Afficher un exemple 
    cs2# show version module 1 epld

EPLD Device                     Version
---------------------------------------
MI   FPGA                        0x7
IO   FPGA                        0x19
MI   FPGA2                       0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2

  12. Vérifiez l’état de tous les ports du cluster.

    1. Ports de cluster

      1. Vérifiez que les ports du cluster sont opérationnels et fonctionnels sur tous les nœuds du cluster :

        network port show -ipspace Cluster
        Afficher un exemple 
        cluster1::*> network port show -ipspace Cluster

Node: node1-01
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/10000 healthy  false
e7b       Cluster      Cluster          up   9000  auto/10000 healthy  false

Node: node1-02
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/10000 healthy  false
e7b       Cluster      Cluster          up   9000  auto/10000 healthy  false

Node: node1-03
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/100000 healthy false
e7b       Cluster      Cluster          up   9000  auto/100000 healthy false

Node: node1-04
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/100000 healthy false
e7b       Cluster      Cluster          up   9000  auto/100000 healthy false

      2. Vérifiez l'état du commutateur à partir du cluster :

        network device-discovery show -protocol cdp
        system cluster-switch show -is-monitoring-enabled-operational true
        Afficher un exemple 
        cluster1::*> network device-discovery show -protocol cdp

node1-02/cdp
            e10a   cs1(FLMXXXXXXXX)         Ethernet1/16/3    N9K-C9332D-GX2B
            e10b   cs2(FDOXXXXXXXX)         Ethernet1/16/3    N9K-C9332D-GX2B
            e11a   cs1(FLMXXXXXXXX)         Ethernet1/16/4    N9K-C9332D-GX2B
            e11b   cs2(FDOXXXXXXXX)         Ethernet1/16/4    N9K-C9332D-GX2B
            e1a    cs1(FLMXXXXXXXX)         Ethernet1/16/1    N9K-C9332D-GX2B
            e1b    cs2(FDOXXXXXXXX)         Ethernet1/16/1    N9K-C9332D-GX2B
            .
            .
            .
            e7a    cs1(FLM284504N6)         Ethernet1/16/2    N9K-C9332D-GX2B
            e7b    cs2(FDO2846056X)         Ethernet1/16/2    N9K-C9332D-GX2B

node1-01/cdp
            e10a   cs1(FLMXXXXXXXX)         Ethernet1/16/3    N9K-C9332D-GX2B
            e10b   cs2(FDOXXXXXXXX)         Ethernet1/16/3    N9K-C9332D-GX2B
            e11a   cs1(FLMXXXXXXXX)         Ethernet1/16/4    N9K-C9332D-GX2B
            e11b   cs2(FDOXXXXXXXX)         Ethernet1/16/4    N9K-C9332D-GX2B
            e1a    cs1(FLMXXXXXXXX)         Ethernet1/16/1    N9K-C9332D-GX2B
            e1b    cs2(FDOXXXXXXXX)         Ethernet1/16/1    N9K-C9332D-GX2B
           .
           .
           .
            e7a    cs1(FLMXXXXXXXX)         Ethernet1/16/2    N9K-C9332D-GX2B
            e7b    cs2(FDOXXXXXXXX)         Ethernet1/16/2    N9K-C9332D-GX2B
.
.
.

cluster1::*> system cluster-switch show -is-monitoring-enabled-operational true
Switch                      Type               Address          Model
--------------------------- ------------------ ---------------- ---------------
cs2(FDOXXXXXXXX)            cluster-network    10.228.137.233   N9K-C9332D-GX2B
     Serial Number: FDOXXXXXXXX
      Is Monitored: true
            Reason: None
  Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                    10.4(2)
    Version Source: CDP/ISDP


cs1(FLMXXXXXXXX)             cluster-network   10.228.137.253   N9K-C9332D-GX2B
     Serial Number: FLMXXXXXXXX
      Is Monitored: true
            Reason: None
  Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                    10.4(2)
    Version Source: CDP/ISDP

    2. Ports HA

      1. Vérifiez que tous les ports HA sont opérationnels et en bon état :

        ha interconnect status show -node <node-name>

    Afficher un exemple 
    cluster1::*> ha interconnect status show -node node1-01
  (system ha interconnect status show)

                       Node: node1-01
              Link 0 Status: up
              Link 1 Status: up
           Is Link 0 Active: true
           Is Link 1 Active: true
         IC RDMA Connection: up
                       Slot: 0
             Debug Firmware: no


Interconnect Port 0 :
                  Port Name: e1a-17
                        MTU: 4096
           Link Information: ACTIVE


Interconnect Port 1 :
                  Port Name: e1b-18
                        MTU: 4096
           Link Information: ACTIVE

cluster1::*> ha interconnect status show -node node1-02
  (system ha interconnect status show)

                       Node: node1-02
              Link 0 Status: up
              Link 1 Status: up
           Is Link 0 Active: true
           Is Link 1 Active: true
         IC RDMA Connection: up
                       Slot: 0
             Debug Firmware: no


Interconnect Port 0 :
                  Port Name: e1a-17
                        MTU: 4096
           Link Information: ACTIVE


Interconnect Port 1 :
                  Port Name: e1b-18
                        MTU: 4096
           Link Information: ACTIVE
.
.
.

    1. Ports de stockage

      1. Vérifiez que tous les ports de stockage sont opérationnels et en bon état :

        storage port show -port-type ENET
        Afficher un exemple 
        cluster1::*> storage port show -port-type ENET


                                      Speed
Node               Port Type  Mode    (Gb/s) State    Status
------------------ ---- ----- ------- ------ -------- -----------
node1-01
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
                   e11b ENET  -          100 enabled  online
node1-02
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
                   e11b ENET  -          100 enabled  online
node1-03
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
node1-04
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
                   e11b ENET  -          100 enabled  online
16 entries were displayed.

    2. Ports d'étagères de stockage

      1. Vérifiez que tous les ports de l'étagère de stockage sont opérationnels et en bon état :

        storage shelf port show
        Afficher un exemple 
        cluster1::*> storage shelf port show

Shelf ID Module State        Internal?
----- -- ------ ------------ ---------
1.1
       0 A      connected    false
       1 A      connected    false
       2 A      connected    false
       3 A      connected    false
       4 A      connected    false
       5 A      connected    false
       6 A      connected    false
       7 A      connected    false
       8 B      connected    false
       9 B      connected    false
      10 B      connected    false
      11 B      connected    false
      12 B      connected    false
      13 B      connected    false
      14 B      connected    false
      15 B      connected    false

16 entries were displayed.

      2. Vérifiez l’état de connexion de tous les ports de l’étagère de stockage :

        storage shelf port show -fields remote-device,remote-port,connector-state
        Afficher un exemple 
        cluster1::*> storage shelf port show -fields remote-device,remote-port,connector-state

shelf id connector-state remote-port    remote-device
----- -- --------------- -------------- -----------------
1.1   0  connected       Ethernet1/17/1 CX9332D-cs1
1.1   1  connected       Ethernet1/15/1 CX9364D-cs1
1.1   2  connected       Ethernet1/17/2 CX9332D-cs1
1.1   3  connected       Ethernet1/15/2 CX9364D-cs1
1.1   4  connected       Ethernet1/17/3 CX9332D-cs1
1.1   5  connected       Ethernet1/15/3 CX9364D-cs1
1.1   6  connected       Ethernet1/17/4 CX9332D-cs1
1.1   7  connected       Ethernet1/15/4 CX9364D-cs1
1.1   8  connected       Ethernet1/19/1 CX9332D-cs1
1.1   9  connected       Ethernet1/17/1 CX9364D-cs1
1.1   10 connected       Ethernet1/19/2 CX9332D-cs1
1.1   11 connected       Ethernet1/17/2 CX9364D-cs1
1.1   12 connected       Ethernet1/19/3 CX9332D-cs1
1.1   13 connected       Ethernet1/17/3 CX9364D-cs1
1.1   14 connected       Ethernet1/19/4 CX9332D-cs1
1.1   15 connected       Ethernet1/17/4 CX9364D-cs1

16 entries were displayed.

  13. Vérifiez que le cluster est sain :

    cluster show

    Afficher un exemple 
    cluster1::*> cluster show


Node                 Health  Eligibility   Epsilon
-------------------- ------- ------------  ------------
node1-01             true    true          false
node1-02             true    true          false
node1-03             true    true          false
node1-04             true    true          true

4 entries were displayed.

  14. Répétez les étapes 6 à 13 pour installer le logiciel NX-OS et les images EPLD sur le commutateur cs1.

  15. Activer la restauration automatique sur les LIF du cluster.

    network interface modify -vserver Cluster -lif * -auto-revert true

  16. Vérifiez que les LIF du cluster sont revenues à leur port d'origine :

    network interface show -role cluster
    Afficher un exemple 
    cluster1::*> network interface show -role cluster

            Logical         Status     Network            Current     Current Is
Vserver     Interface       Admin/Oper Address/Mask       Node        Port    Home
----------- --------------- ---------- ------------------ ----------- ------- ----
Cluster
            node1-01_clus1  up/up      169.254.36.44/16   node1-01    e7a     true
            node1-01_clus2  up/up      169.254.7.5/16     node1-01    e7b     true
            node1-02_clus1  up/up      169.254.197.206/16 node1-02    e7a     true
            node1-02_clus2  up/up      169.254.195.186/16 node1-02    e7b     true
            node1-03_clus1  up/up      169.254.192.49/16  node1-03    e7a     true
            node1-03_clus2  up/up      169.254.182.76/16  node1-03    e7b     true
            node1-04_clus1  up/up      169.254.59.49/16   node1-04    e7a     true
            node1-04_clus2  up/up      169.254.62.244/16  node1-04    e7b     true

    Si certaines interfaces logiques (LIF) du cluster ne sont pas revenues à leurs ports d'origine, rétablissez-les manuellement depuis le nœud local :

    network interface revert -vserver Cluster -lif <lif-name>

Quelle est la prochaine étape ?

Après avoir installé ou mis à jour le logiciel NX-OS, vous"installer ou mettre à niveau le fichier de configuration de référence (RCF)" .