# sanlun lun show all

controller(7mode/E-Series)/            device     host               lun
vserver(cDOT/FlashRay)   lun-pathname  filename   adapter  protocol  size    Product
------------------------------------------------------------------------------------
data_vserver          /vol/vol1/lun1   /dev/sdb   host16   FCP       120.0g  cDOT
data_vserver          /vol/vol1/lun1   /dev/sdc   host15   FCP       120.0g  cDOT
data_vserver          /vol/vol2/lun2   /dev/sdd   host16   FCP       120.0g  cDOT
data_vserver          /vol/vol2/lun2   /dev/sde   host15   FCP       120.0g  cDOT

# multipath -ll
3600a098038303634722b4d59646c4436 dm-28 NETAPP,LUN C-Mode
size=10G features='3 queue_if_no_path pg_init_retries 50' hwhandler='1 alua' wp=rw
|-+- policy='service-time 0' prio=50 status=active
| |- 16:0:6:35 sdwb 69:624 active ready running
| |- 16:0:5:35 sdun 66:752 active ready running
|-+- policy='service-time 0' prio=10 status=enabled
|- 15:0:0:35 sdaj 66:48 active ready running
|- 15:0:1:35 sdbx 68:176 active ready running

chkconfig multipathd on
/etc/init.d/multipathd start

blacklist {
        wwid <DevId>
        devnode "^(ram|raw|loop|fd|md|dm-|sr|scd|st)[0-9]*"
        devnode "^hd[a-z]"
        devnode "^cciss.*"
}

+
`sda` is the local SCSI disk that you want to add to the blacklist.

. Add the `WWID` to the blacklist stanza in `/etc/multipath.conf`:
[source,cli]
+

Always check your `/etc/multipath.conf` file, especially in the defaults section, for legacy settings that might be overriding default settings.

The following table demonstrates the critical `multipathd` parameters for ONTAP LUNs and the required values. If a host is connected to LUNs from other vendors and any of these parameters are overridden, they must be corrected by later stanzas in the `multipath.conf` file that apply specifically to ONTAP LUNs. Without this correction, the ONTAP LUNs might not work as expected. You should only override these defaults in consultation with NetApp, the OS vendor, or both, and only when the impact is fully understood.

//ONTAPDOC-2578 9-Dec-2024
//ONTAPDOC-2561 25-Nov-202


[cols=2*,options="header"]
|===
| Parameter
| Setting
| detect_prio | yes
| dev_loss_tmo | "infinity"
| failback | immediate
| fast_io_fail_tmo | 5
| features | "2 pg_init_retries 50"
| flush_on_last_del | "yes"
| hardware_handler | "0"
| no_path_retry | queue
| path_checker | "tur"
| path_grouping_policy | "group_by_prio"
| path_selector | "service-time 0"
| polling_interval | 5
| prio | "ontap"
| product | LUN.*
| retain_attached_hw_handler | yes
| rr_weight | "uniform"
| user_friendly_names | no
| vendor | NETAPP
|===

.Example

The following example shows how to correct an overridden default. In this case, the `multipath.conf` file defines values for `path_checker` and `no_path_retry` that are not compatible with ONTAP LUNs. If they cannot be removed because of other SAN arrays still attached to the host, these parameters can be corrected specifically for ONTAP LUNs with a device stanza.

NOTE: To configure Oracle Linux 8.0 Red Hat Enterprise Kernel (RHCK), use the link:hu_rhel_80.html#recommended-settings[recommended settings] for Red Hat Enterprise Linux (RHEL) 8.0.

== Known issues

There are no known issues for the Oracle Linux 8.0 with ONTAP release.

NOTE: For Oracle Linux (Red Hat compatible kernel) known issues, see the link:hu_rhel_80.html#known-problems-and-limitations[known issues] for Red Hat Enterprise Linux (RHEL) 8.0.