Installare o aggiornare il file di configurazione di riferimento
Dopo aver configurato per la prima volta gli switch di archiviazione Nexus 9336C-FX2 e 9336C-FX2-T, installare il file di configurazione di riferimento (RCF).
Per ulteriori informazioni sull'installazione di RCF, consultare l'articolo della Knowledge base"Come cancellare la configurazione su uno switch Cisco Interconnect mantenendo la connettività remota".
Verificare le seguenti installazioni e connessioni:
-
Collegamento della console allo switch. Il collegamento alla console è opzionale se si dispone dell'accesso remoto allo switch.
-
Lo switch CS1 e lo switch CS2 sono accesi e la configurazione iniziale dello switch è completa (l'indirizzo IP di gestione e SSH sono impostati).
-
È stata installata la versione NX-OS desiderata.
-
Le porte del cluster di nodi ONTAP non sono connesse.
Fase 1: Installare l'RCF sugli interruttori
-
Accedere allo switch CS1 usando SSH o usando una console seriale.
-
Copiare l'RCF nella memoria di avvio dello switch CS1 utilizzando uno dei seguenti protocolli di trasferimento: FTP, TFTP, SFTP o SCP.
Per ulteriori informazioni sui comandi Cisco, consultare la guida appropriata in "Cisco Nexus 9000 Series NX-OS Command Reference".
Mostra esempio
Questo esempio mostra l'utilizzo di TFTP per copiare un RCF nel bootflash dello switch CS1:
cs1# copy tftp: bootflash: vrf management Enter source filename: Nexus_9336C_RCF_v1.6-Storage.txt Enter hostname for the tftp server: 172.22.201.50 Trying to connect to tftp server......Connection to Server Established. TFTP get operation was successful Copy complete, now saving to disk (please wait)...
-
Applicare l'RCF precedentemente scaricato al bootflash.
Per ulteriori informazioni sui comandi Cisco, consultare la guida appropriata in "Cisco Nexus 9000 Series NX-OS Command Reference".
Mostra esempio
Questo esempio mostra l'RCF
Nexus_9336C_RCF_v1.6-Storage.txtinstallato sull'interruttore CS1:cs1# copy Nexus_9336C_RCF_v1.6-Storage.txt running-config echo-commands
-
Esaminare l'output del banner dal
show banner motdcomando. Leggere e seguire queste istruzioni per garantire la corretta configurazione e il corretto funzionamento dell'interruttore.Mostra esempio
cs1# show banner motd ****************************************************************************** * NetApp Reference Configuration File (RCF) * * Switch : Nexus N9K-C9336C-FX2 * Filename : Nexus_9336C_RCF_v1.6-Storage.txt * Date : 10-23-2020 * Version : v1.6 * * Port Usage : Storage configuration * Ports 1-36: 100GbE Controller and Shelf Storage Ports ******************************************************************************
-
Verificare che l'RCF sia la versione più recente corretta:
show running-configQuando si controlla l'output per verificare che l'RCF sia corretto, assicurarsi che le seguenti informazioni siano corrette:
-
Il banner RCF
-
Le impostazioni di nodo e porta
-
Personalizzazioni
L'output varia in base alla configurazione del sito. Controllare le impostazioni della porta e fare riferimento alle note di rilascio per eventuali modifiche specifiche all'RCF installato.
-
-
Registrare eventuali aggiunte personalizzate tra l'attuale
running-configfile e il file RCF in uso. -
Dopo aver verificato che le versioni RCF e le impostazioni degli switch siano corrette, copiare il file
running-configfile alstartup-configfile.cs1# copy running-config startup-config [########################################] 100% Copy complete
-
Salva i dettagli di configurazione di base nel
write_erase.cfgfile sul bootflash.cs1# show run | i "username admin password" > bootflash:write_erase.cfgcs1# show run | section "vrf context management" >> bootflash:write_erase.cfgcs1# show run | section "interface mgmt0" >> bootflash:write_erase.cfgcs1# show run | section "switchname" >> bootflash:write_erase.cfg -
Per RCF versione 1.12 e successive, eseguire i seguenti comandi:
cs1# echo "hardware access-list tcam region ing-racl 1024" >> bootflash:write_erase.cfgcs1# echo "hardware access-list tcam region egr-racl 1024" >> bootflash:write_erase.cfgcs1# echo "hardware access-list tcam region ing-l2-qos 1280" >> bootflash:write_erase.cfgVedi l'articolo della Knowledge Base"Come cancellare la configurazione su uno switch Cisco Interconnect mantenendo la connettività remota" per ulteriori dettagli.
-
Verificare che il
write_erase.cfgil file è popolato come previsto:show file bootflash:write_erase.cfg -
Emettere il
write erasecomando per cancellare la configurazione salvata corrente:cs1# write eraseWarning: This command will erase the startup-configuration.Do you wish to proceed anyway? (y/n) [n] y -
Copiare la configurazione di base salvata in precedenza nella configurazione di avvio.
cs1# copy bootflash:write_erase.cfg startup-config -
Riavviare l'interruttore CS1.
cs1# reloadThis command will reboot the system. (y/n)? [n] y -
Ripetere i passaggi da 1 a 13 sullo switch cs2.
-
Collegare le porte del cluster di tutti i nodi nel cluster ONTAP agli switch CS1 e CS2.
Fase 2: Verificare i collegamenti dello switch
-
Verificare che le porte dello switch collegate alle porte del cluster siano up.
show interface briefMostra esempio
cs1# show interface brief | grep up mgmt0 -- up <mgmt ip address> 1000 1500 Eth1/11 1 eth trunk up none 100G(D) -- Eth1/12 1 eth trunk up none 100G(D) -- Eth1/13 1 eth trunk up none 100G(D) -- Eth1/14 1 eth trunk up none 100G(D) -- Eth1/15 1 eth trunk up none 100G(D) -- Eth1/16 1 eth trunk up none 100G(D) -- Eth1/17 1 eth trunk up none 100G(D) -- Eth1/18 1 eth trunk up none 100G(D) -- Eth1/23 1 eth trunk up none 100G(D) -- Eth1/24 1 eth trunk up none 100G(D) -- Eth1/25 1 eth trunk up none 100G(D) -- Eth1/26 1 eth trunk up none 100G(D) -- Eth1/27 1 eth trunk up none 100G(D) -- Eth1/28 1 eth trunk up none 100G(D) -- Eth1/29 1 eth trunk up none 100G(D) -- Eth1/30 1 eth trunk up none 100G(D) --
-
Verificare che i nodi del cluster si trovino nelle VLAN del cluster corrette utilizzando i seguenti comandi:
show vlan briefshow interface trunkMostra esempio
cs1# show vlan brief VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Po999 30 VLAN0030 active Eth1/1, Eth1/2, Eth1/3, Eth1/4 Eth1/5, Eth1/6, Eth1/7, Eth1/8 Eth1/9, Eth1/10, Eth1/11 Eth1/12, Eth1/13, Eth1/14 Eth1/15, Eth1/16, Eth1/17 Eth1/18, Eth1/19, Eth1/20 Eth1/21, Eth1/22, Eth1/23 Eth1/24, Eth1/25, Eth1/26 Eth1/27, Eth1/28, Eth1/29 Eth1/30, Eth1/31, Eth1/32 Eth1/33, Eth1/34, Eth1/35 Eth1/36 cs1# show interface trunk ----------------------------------------------------- Port Native Status Port Vlan Channel ----------------------------------------------------- Eth1/1 1 trunking -- Eth1/2 1 trunking -- Eth1/3 1 trunking -- Eth1/4 1 trunking -- Eth1/5 1 trunking -- Eth1/6 1 trunking -- Eth1/7 1 trunking -- Eth1/8 1 trunking -- Eth1/9 1 trunking -- Eth1/10 1 trunking -- Eth1/11 1 trunking -- Eth1/12 1 trunking -- Eth1/13 1 trunking -- Eth1/14 1 trunking -- Eth1/15 1 trunking -- Eth1/16 1 trunking -- Eth1/17 1 trunking -- Eth1/18 1 trunking -- Eth1/19 1 trunking -- Eth1/20 1 trunking -- Eth1/21 1 trunking -- Eth1/22 1 trunking -- Eth1/23 1 trunking -- Eth1/24 1 trunking -- Eth1/25 1 trunking -- Eth1/26 1 trunking -- Eth1/27 1 trunking -- Eth1/28 1 trunking -- Eth1/29 1 trunking -- Eth1/30 1 trunking -- Eth1/31 1 trunking -- Eth1/32 1 trunking -- Eth1/33 1 trunking -- Eth1/34 1 trunking -- Eth1/35 1 trunking -- Eth1/36 1 trunking -- -------------------------------------------------------------------------------- Port Vlans Allowed on Trunk -------------------------------------------------------------------------------- Eth1/1 30 Eth1/2 30 Eth1/3 30 Eth1/4 30 Eth1/5 30 Eth1/6 30 Eth1/7 30 Eth1/8 30 Eth1/9 30 Eth1/10 30 Eth1/11 30 Eth1/12 30 Eth1/13 30 Eth1/14 30 Eth1/15 30 Eth1/16 30 Eth1/17 30 Eth1/18 30 Eth1/19 30 Eth1/20 30 Eth1/21 30 Eth1/22 30 Eth1/23 30 Eth1/24 30 Eth1/25 30 Eth1/26 30 Eth1/27 30 Eth1/28 30 Eth1/29 30 Eth1/30 30 Eth1/31 30 Eth1/32 30 Eth1/33 30 Eth1/34 30 Eth1/35 30 Eth1/36 30 -------------------------------------------------------------------------------- Port Vlans Err-disabled on Trunk -------------------------------------------------------------------------------- Eth1/1 none Eth1/2 none Eth1/3 none Eth1/4 none Eth1/5 none Eth1/6 none Eth1/7 none Eth1/8 none Eth1/9 none Eth1/10 none Eth1/11 none Eth1/12 none Eth1/13 none Eth1/14 none Eth1/15 none Eth1/16 none Eth1/17 none Eth1/18 none Eth1/19 none Eth1/20 none Eth1/21 none Eth1/22 none Eth1/23 none Eth1/24 none Eth1/25 none Eth1/26 none Eth1/27 none Eth1/28 none Eth1/29 none Eth1/30 none Eth1/31 none Eth1/32 none Eth1/33 none Eth1/34 none Eth1/35 none Eth1/36 none -------------------------------------------------------------------------------- Port STP Forwarding -------------------------------------------------------------------------------- Eth1/1 none Eth1/2 none Eth1/3 none Eth1/4 none Eth1/5 none Eth1/6 none Eth1/7 none Eth1/8 none Eth1/9 none Eth1/10 none Eth1/11 30 Eth1/12 30 Eth1/13 30 Eth1/14 30 Eth1/15 30 Eth1/16 30 Eth1/17 30 Eth1/18 30 Eth1/19 none Eth1/20 none Eth1/21 none Eth1/22 none Eth1/23 30 Eth1/24 30 Eth1/25 30 Eth1/26 30 Eth1/27 30 Eth1/28 30 Eth1/29 30 Eth1/30 30 Eth1/31 none Eth1/32 none Eth1/33 none Eth1/34 none Eth1/35 none Eth1/36 none -------------------------------------------------------------------------------- Port Vlans in spanning tree forwarding state and not pruned -------------------------------------------------------------------------------- Eth1/1 Feature VTP is not enabled none Eth1/2 Feature VTP is not enabled none Eth1/3 Feature VTP is not enabled none Eth1/4 Feature VTP is not enabled none Eth1/5 Feature VTP is not enabled none Eth1/6 Feature VTP is not enabled none Eth1/7 Feature VTP is not enabled none Eth1/8 Feature VTP is not enabled none Eth1/9 Feature VTP is not enabled none Eth1/10 Feature VTP is not enabled none Eth1/11 Feature VTP is not enabled 30 Eth1/12 Feature VTP is not enabled 30 Eth1/13 Feature VTP is not enabled 30 Eth1/14 Feature VTP is not enabled 30 Eth1/15 Feature VTP is not enabled 30 Eth1/16 Feature VTP is not enabled 30 Eth1/17 Feature VTP is not enabled 30 Eth1/18 Feature VTP is not enabled 30 Eth1/19 Feature VTP is not enabled none Eth1/20 Feature VTP is not enabled none Eth1/21 Feature VTP is not enabled none Eth1/22 Feature VTP is not enabled none Eth1/23 Feature VTP is not enabled 30 Eth1/24 Feature VTP is not enabled 30 Eth1/25 Feature VTP is not enabled 30 Eth1/26 Feature VTP is not enabled 30 Eth1/27 Feature VTP is not enabled 30 Eth1/28 Feature VTP is not enabled 30 Eth1/29 Feature VTP is not enabled 30 Eth1/30 Feature VTP is not enabled 30 Eth1/31 Feature VTP is not enabled none Eth1/32 Feature VTP is not enabled none Eth1/33 Feature VTP is not enabled none Eth1/34 Feature VTP is not enabled none Eth1/35 Feature VTP is not enabled none Eth1/36 Feature VTP is not enabled nonePer informazioni dettagliate sull'utilizzo di porte e VLAN specifiche, fare riferimento alla sezione banner e note importanti nell'RCF.
Fase 3: Configurare il cluster ONTAP
NetApp consiglia di utilizzare System Manager per configurare nuovi cluster.
System Manager offre un workflow semplice e facile per la configurazione e il setup del cluster, che include l'assegnazione di un indirizzo IP di gestione dei nodi, l'inizializzazione del cluster, la creazione di un Tier locale, la configurazione dei protocolli e il provisioning dello storage iniziale.
Passare a. "Configurare ONTAP su un nuovo cluster con Gestione di sistema" per le istruzioni di installazione.
Dopo aver installato o aggiornato il tuo RCF,"verificare la configurazione SSH"