La versione in lingua italiana fornita proviene da una traduzione automatica. Per eventuali incoerenze, fare riferimento alla versione in lingua inglese.

Installa o aggiorna il software NX-OS

11/10/2025 Collaboratori

PDF

Seguire questa procedura per installare o aggiornare il software NX-OS sullo switch Nexus 9364D-GX2A.

Requisiti di revisione

Prima di iniziare

Verificare quanto segue:

Completare la procedura in"Prepararsi all'installazione di NX-OS e RCF" .
È disponibile un backup aggiornato della configurazione dello switch.
È presente un cluster completamente funzionante (nessun errore nei log o problemi simili).

Documentazione suggerita

"Pagina dello switch Ethernet Cisco"

Consultare la tabella di compatibilità degli switch per le versioni ONTAP e NX-OS supportate.
"Guide per l'aggiornamento e il downgrade del software"

Per la documentazione completa sulle procedure di upgrade e downgrade degli switch Cisco , fare riferimento alle guide software e di aggiornamento appropriate disponibili sul sito Web Cisco .
"Aggiornamento Cisco Nexus 9000 e 3000 e matrice ISSU"

Fornisce informazioni sull'aggiornamento/downgrade dirompente per il software Cisco NX-OS sugli switch Nexus serie 9000 in base alle versioni correnti e di destinazione.

Nella pagina, seleziona Disruptive Upgrade e seleziona la versione corrente e quella di destinazione dall'elenco a discesa.

Informazioni sugli esempi

Gli esempi in questa procedura utilizzano la seguente nomenclatura di switch e nodi:

I nomi dei due switch Cisco sono cs1 e cs2.
I nomi dei nodi sono node1-01, node1-02, node1-03 e node1-04.
I nomi LIF del cluster sono node1-01_clus1, node1-01_clus2, node1-02_clus1, node1-02_clus2, node1-03_clus1, node1-03_clus2, node1-04_clus1 e node1-04_clus2.
IL cluster1::*> il prompt indica il nome del cluster.

Installa il software

La procedura richiede l'uso sia dei comandi ONTAP sia dei comandi degli switch Cisco Nexus serie 9000; salvo diversa indicazione, vengono utilizzati i comandi ONTAP .

NX-OS 10.4.2 è l'unica versione supportata per gli switch Cisco Nexus 9364D-GX2A in un cluster ONTAP .
Non effettuare l'upgrade o il downgrade della versione NX-OS a una versione non supportata; al momento è supportata solo la versione 10.4.2.

Passi

Collegare lo switch alla rete di gestione.
Utilizzare il comando ping per verificare la connettività al server che ospita il software NX-OS e l'RCF.
Mostra esempio
Questo esempio verifica che lo switch possa raggiungere il server all'indirizzo IP 172.19.2.1:
cs2# ping 172.19.2.1 Pinging 172.19.2.1 with 0 bytes of data: Reply From 172.19.2.1: icmp_seq = 0. time= 5910 usec.

Visualizza le porte del cluster su ciascun nodo connesso agli switch del cluster:

network device-discovery show

Mostra esempio

cluster1::*> network device-discovery show

Node/       Local  Discovered
Protocol    Port   Device (LLDP: ChassisID) Interface         Platform
----------- ------ ------------------------ ----------------  ----------------
node1-01/cdp
            e10a   cs1(FLMXXXXXXXX)         Ethernet1/16/3    N9K-C9364D-GX2A
            e10b   cs2(FDOXXXXXXXX)         Ethernet1/13/3    N9K-C9364D-GX2A
            e11a   cs1(FLMXXXXXXXX)         Ethernet1/16/4    N9K-C9364D-GX2A
            e11b   cs2(FDOXXXXXXXX)         Ethernet1/13/4    N9K-C9364D-GX2A
            e1a    cs1(FLMXXXXXXXX)         Ethernet1/16/1    N9K-C9364D-GX2A
            e1b    cs2(FDOXXXXXXXX)         Ethernet1/13/1    N9K-C9364D-GX2A
            .
            .
            .

            e7a    cs1(FLMXXXXXXXX)         Ethernet1/16/2    N9K-C9364D-GX2A
            e7b    cs2(FDOXXXXXXXX)         Ethernet1/13/2    N9K-C9364D-GX2A

node1-01/lldp
            e10a   cs1 (c8:60:8f:xx:xx:xx)  Ethernet1/16/3    -
            e10b   cs2 (04:e3:87:xx:xx:xx)  Ethernet1/13/3    -
            e11a   cs1 (c8:60:8f:xx:xx:xx)  Ethernet1/16/4    -
            e11b   cs2 (04:e3:87:xx:xx:xx)  Ethernet1/13/4    -
            e1a    cs1 (c8:60:8f:xx:xx:xx)  Ethernet1/16/1    -
            e1b    cs2 (04:e3:87:xx:xx:xx)  Ethernet1/13/1    -
            .
            .
            .
            e7a    cs1 (c8:60:8f:xx:xx:xx)  Ethernet1/16/2    -
            e7b    cs2 (04:e3:87:xx:xx:xx)  Ethernet1/13/2    -
.
.
.

Verificare lo stato amministrativo e operativo di ogni porto.

Porte cluster

Verificare che tutte le porte del cluster siano attive e integre:

network port show -ipspace Cluster

Mostra esempio

cluster1::*> network port show -ipspace Cluster

Node: node1-01
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/100000 healthy false
e7b       Cluster      Cluster          up   9000  auto/100000 healthy false

Node: node1-02
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/100000 healthy false
e7b       Cluster      Cluster          up   9000  auto/100000 healthy false

Node: node1-03

                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/10000 healthy  false
e7b       Cluster      Cluster          up   9000  auto/10000 healthy  false

Node: node1-04
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/10000 healthy  false
e7b       Cluster      Cluster          up   9000  auto/10000 healthy  false

Verificare che tutte le interfacce cluster (LIF) siano sulla porta home:

network interface show -role cluster

Mostra esempio

cluster1::*> network interface show -role cluster

            Logical         Status     Network            Current   Current Is
Vserver     Interface       Admin/Oper Address/Mask       Node      Port    Home
----------- --------------- ---------- ------------------ --------- ------- ----
Cluster
            node1-01_clus1  up/up      169.254.36.44/16   node1-01  e7a     true
            node1-01_clus2  up/up      169.254.7.5/16     node1-01  e7b     true
            node1-02_clus1  up/up      169.254.197.206/16 node1-02  e7a     true
            node1-02_clus2  up/up      169.254.195.186/16 node1-02  e7b     true
            node1-03_clus1  up/up      169.254.192.49/16  node1-03  e7a     true
            node1-03_clus2  up/up      169.254.182.76/16  node1-03  e7b     true
            node1-04_clus1  up/up      169.254.59.49/16   node1-04  e7a     true
            node1-04_clus2  up/up      169.254.62.244/16  node1-04  e7b     true

8 entries were displayed.

Verificare che il cluster visualizzi le informazioni per entrambi gli switch del cluster:

system cluster-switch show -is-monitoring-enabled-operational true

Mostra esempio

cluster1::*> system cluster-switch show -is-monitoring-enabled-operational true

Switch                      Type               Address          Model
--------------------------- ------------------ ---------------- ---------------
cs2(FDOXXXXXXXX)            cluster-network    10.228.137.233   N9K-C9364D-GX2A
     Serial Number: FDOXXXXXXXX
      Is Monitored: true
            Reason: None
  Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                    10.4(2)
    Version Source: CDP/ISDP


cs1(FLMXXXXXXXX)             cluster-network   10.228.137.253   N9K-C9364D-GX2A
     Serial Number: FLMXXXXXXXX
      Is Monitored: true
            Reason: None
  Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                    10.4(2)
    Version Source: CDP/ISDP

2 entries were displayed.

Porte HA
1. Verificare che tutte le porte HA siano attive e in stato di integrità:
  
  ha interconnect status show -node <node-name>

Mostra esempio

cluster1::*> ha interconnect status show -node node1-01
  (system ha interconnect status show)

                       Node: node1-01
              Link 0 Status: up
              Link 1 Status: up
           Is Link 0 Active: true
           Is Link 1 Active: true
         IC RDMA Connection: up
                       Slot: 0
             Debug Firmware: no


Interconnect Port 0 :
                  Port Name: e1a-17
                        MTU: 4096
           Link Information: ACTIVE


Interconnect Port 1 :
                  Port Name: e1b-18
                        MTU: 4096
           Link Information: ACTIVE

cluster1::*> ha interconnect status show -node node1-02
  (system ha interconnect status show)

                       Node: node1-02
              Link 0 Status: up
              Link 1 Status: up
           Is Link 0 Active: true
           Is Link 1 Active: true
         IC RDMA Connection: up
                       Slot: 0
             Debug Firmware: no


Interconnect Port 0 :
                  Port Name: e1a-17
                        MTU: 4096
           Link Information: ACTIVE


Interconnect Port 1 :
                  Port Name: e1b-18
                        MTU: 4096
           Link Information: ACTIVE
.
.
.

Porte di archiviazione

Verificare che tutte le porte di archiviazione siano attive e integre:

storage port show -port-type ENET

Mostra esempio

cluster1::*> storage port show -port-type ENET

                                      Speed
Node               Port Type  Mode    (Gb/s) State    Status
------------------ ---- ----- ------- ------ -------- -----------
node1-01
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
                   e11b ENET  -          100 enabled  online
node1-02
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
                   e11b ENET  -          100 enabled  online
node1-03
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
node1-04
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
                   e11b ENET  -          100 enabled  online
16 entries were displayed.

Porte per ripiani portaoggetti

Verificare che tutte le porte dello scaffale di archiviazione siano attive e in buono stato:

storage shelf port show

Mostra esempio

cluster1::*> storage shelf port show

Shelf ID Module State        Internal?
----- -- ------ ------------ ---------
1.1
       0 A      connected    false
       1 A      connected    false
       2 A      connected    false
       3 A      connected    false
       4 A      connected    false
       5 A      connected    false
       6 A      connected    false
       7 A      connected    false
       8 B      connected    false
       9 B      connected    false
      10 B      connected    false
      11 B      connected    false
      12 B      connected    false
      13 B      connected    false
      14 B      connected    false
      15 B      connected    false

16 entries were displayed.

Verificare lo stato di connessione di tutte le porte dello scaffale di archiviazione:

storage shelf port show -fields remote-device,remote-port,connector-state

Mostra esempio

cluster1::*> storage shelf port show -fields remote-device,remote-port,connector-state

shelf id connector-state remote-port    remote-device
----- -- --------------- -------------- -----------------
1.1   0  connected       Ethernet1/17/1 CX9332D-cs1
1.1   1  connected       Ethernet1/15/1 CX9364D-cs1
1.1   2  connected       Ethernet1/17/2 CX9332D-cs1
1.1   3  connected       Ethernet1/15/2 CX9364D-cs1
1.1   4  connected       Ethernet1/17/3 CX9332D-cs1
1.1   5  connected       Ethernet1/15/3 CX9364D-cs1
1.1   6  connected       Ethernet1/17/4 CX9332D-cs1
1.1   7  connected       Ethernet1/15/4 CX9364D-cs1
1.1   8  connected       Ethernet1/19/1 CX9332D-cs1
1.1   9  connected       Ethernet1/17/1 CX9364D-cs1
1.1   10 connected       Ethernet1/19/2 CX9332D-cs1
1.1   11 connected       Ethernet1/17/2 CX9364D-cs1
1.1   12 connected       Ethernet1/19/3 CX9332D-cs1
1.1   13 connected       Ethernet1/17/3 CX9364D-cs1
1.1   14 connected       Ethernet1/19/4 CX9332D-cs1
1.1   15 connected       Ethernet1/17/4 CX9364D-cs1

16 entries were displayed.

Disabilitare il ripristino automatico sui LIF del cluster. I LIF del cluster eseguono il failover sullo switch del cluster partner e vi rimangono mentre si esegue la procedura di aggiornamento sullo switch di destinazione:

network interface modify -vserver Cluster -lif * -auto-revert false

Copiare il software NX-OS e le immagini EPLD sullo switch Nexus 9364D-GX2A.

Mostra esempio

cs2# copy sftp: bootflash: vrf management
Enter source filename: /code/nxos.10.4.2.bin
Enter hostname for the sftp server: 172.19.2.1
Enter username: root

Outbound-ReKey for 172.19.2.1:22
Inbound-ReKey for 172.19.2.1:22
root@172.19.2.1's password:
sftp> progress
Progress meter enabled
sftp> get   /code/nxos.10.4.2.bin  /bootflash/nxos.10.4.2.bin
/code/nxos.10.4.2.bin  100% 1261MB   9.3MB/s   02:15
sftp> exit
Copy complete, now saving to disk (please wait)...
Copy complete.

cs2# copy sftp: bootflash: vrf management
Enter source filename: /code/n9000-epld.10.4.2.F.img
Enter hostname for the sftp server: 172.19.2.1
Enter username: user1

Outbound-ReKey for 172.19.2.1:22
Inbound-ReKey for 172.19.2.1:22
user1@172.19.2.1's password:
sftp> progress
Progress meter enabled
sftp> get   /code/n9000-epld.10.4.2.F.img  /bootflash/n9000-epld.10.4.2.F.img
/code/n9000-epld.10.4.2.F.img  100%  161MB   9.5MB/s   00:16
sftp> exit
Copy complete, now saving to disk (please wait)...
Copy complete.

Verificare la versione in esecuzione del software NX-OS:

show version

Mostra esempio

cs2# show version
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (C) 2002-2025, Cisco and/or its affiliates.
All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under their own
licenses, such as open source.  This software is provided "as is," and unless
otherwise stated, there is no warranty, express or implied, including but not
limited to warranties of merchantability and fitness for a particular purpose.
Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or
GNU General Public License (GPL) version 3.0  or the GNU
Lesser General Public License (LGPL) Version 2.1 or
Lesser General Public License (LGPL) Version 2.0.
A copy of each such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://opensource.org/licenses/gpl-3.0.html and
http://www.opensource.org/licenses/lgpl-2.1.php and
http://www.gnu.org/licenses/old-licenses/library.txt.


Software
  BIOS: version 01.14
  NXOS: version 10.4(1) [Feature Release]
  Host NXOS: version 10.4(1)
  BIOS compile time:  11/25/2024
  NXOS image file is: bootflash:///nxos64-cs.10.4.1.F.bin
  NXOS compile time:  11/30/2023 12:00:00 [12/14/2023 05:25:50]
  NXOS boot mode: LXC


Hardware
  cisco Nexus9000 C9332D-GX2B Chassis
  Intel(R) Xeon(R) CPU D-1633N @ 2.50GHz with 32802156 kB of memory.
  Processor Board ID FLMXXXXXXXX
  Device name: cs2
  bootflash:  115802886 kB


Kernel uptime is 5 day(s), 2 hour(s), 13 minute(s), 21 second(s)


Last reset at 3580 usecs after Thu Jun  5 15:55:08 2025
  Reason: Reset Requested by CLI command reload
  System version: 10.4(1)
  Service:


plugin
  Core Plugin, Ethernet Plugin


Active Package(s):

cs2#

Installare l'immagine NX-OS.

L'installazione del file immagine fa sì che questo venga caricato ogni volta che lo switch viene riavviato.

Mostra esempio

cs2# install all nxos bootflash:nxos.10.4.2.bin

Installer will perform compatibility check first. Please wait.
Installer is forced disruptive

Verifying image bootflash:/nxos.10.4.2.bin for boot variable "nxos".
[] 100% -- SUCCESS

Verifying image type.
[] 100% -- SUCCESS

Preparing "nxos" version info using image bootflash:/nxos.10.4.2.bin.
[] 100% -- SUCCESS

Preparing "bios" version info using image bootflash:/nxos.10.4.2.bin.
[] 100% -- SUCCESS

Performing module support checks.
[] 100% -- SUCCESS

Notifying services about system upgrade.
[] 100% -- SUCCESS


Compatibility check is done:
Module  Bootable  Impact          Install-type  Reason
------  --------  --------------- ------------  ---------
  1     yes       Disruptive      Reset         Default upgrade is not hitless



Images will be upgraded according to following table:

Module   Image    Running-Version(pri:alt)                 New-Version         Upg-Required
------- --------- ---------------------------------------- ------------------- ------------
  1      nxos     10.4(1)                                  10.4(2)             Yes
  1      bios     xx.xx.:xx.xx                             xxx                 No


Switch will be reloaded for disruptive upgrade.

Do you want to continue with the installation (y/n)? [n] y

Install is in progress, please wait.

Performing runtime checks.
[] 100% -- SUCCESS

Setting boot variables.
[] 100% -- SUCCESS

Performing configuration copy.
[] 100% -- SUCCESS

Module 1: Refreshing compact flash and upgrading bios/loader/bootrom.
Warning: please do not remove or power off the module at this time.
[] 100% -- SUCCESS

Finishing the upgrade, switch will reboot in 10 seconds.

Verificare la nuova versione del software NX-OS dopo il riavvio dello switch:

show version

Mostra esempio

cs2# show version
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (C) 2002-2025, Cisco and/or its affiliates.
All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under their own
licenses, such as open source.  This software is provided "as is," and unless
otherwise stated, there is no warranty, express or implied, including but not
limited to warranties of merchantability and fitness for a particular purpose.
Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or
GNU General Public License (GPL) version 3.0  or the GNU
Lesser General Public License (LGPL) Version 2.1 or
Lesser General Public License (LGPL) Version 2.0.
A copy of each such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://opensource.org/licenses/gpl-3.0.html and
http://www.opensource.org/licenses/lgpl-2.1.php and
http://www.gnu.org/licenses/old-licenses/library.txt.


Software
  BIOS: version 01.14
  NXOS: version 10.4(2) [Feature Release]
  Host NXOS: version 10.4(2)
  BIOS compile time:  11/25/2024
  NXOS image file is: bootflash:///nxos64-cs.10.4.2.F.bin
  NXOS compile time:  11/30/2023 12:00:00 [12/14/2023 05:25:50]
  NXOS boot mode: LXC


Hardware
  cisco Nexus9000 C9332D-GX2B Chassis
  Intel(R) Xeon(R) CPU D-1633N @ 2.50GHz with 32802156 kB of memory.
  Processor Board ID FLMXXXXXXXX
  Device name: cs2
  bootflash:  115802886 kB


Kernel uptime is 5 day(s), 2 hour(s), 13 minute(s), 21 second(s)


Last reset at 3580 usecs after Thu Jun  5 15:55:08 2025
  Reason: Reset Requested by CLI command reload
  System version: 10.4(2)
  Service:


plugin
  Core Plugin, Ethernet Plugin


Active Package(s):

cs2#

Aggiornare l'immagine EPLD e riavviare lo switch.

Mostra esempio

cs2# show version module 1 epld

EPLD Device                     Version
---------------------------------------
MI   FPGA                        0x7
IO   FPGA                        0x17
MI   FPGA2                       0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2

cs2# install epld bootflash:n9000-epld.10.4.2.F.img module all
Compatibility check:
Module        Type         Upgradable        Impact    Reason
------  ------------------ ----------------- --------- -----------
     1         SUP         Yes       disruptive  Module Upgradable

Retrieving EPLD versions.... Please wait.
Images will be upgraded according to following table:
Module  Type   EPLD              Running-Version   New-Version  Upg-Required
------- ------ ----------------- ----------------- ------------ ------------
     1  SUP    MI FPGA           0x07              0x07         No
     1  SUP    IO FPGA           0x17              0x19         Yes
     1  SUP    MI FPGA2          0x02              0x02         No
The above modules require upgrade.
The switch will be reloaded at the end of the upgrade
Do you want to continue (y/n) ?  [n] y

Proceeding to upgrade Modules.

Starting Module 1 EPLD Upgrade

Module 1 : IO FPGA [Programming] : 100.00% (     64 of      64 sectors)
Module 1 EPLD upgrade is successful.
Module   Type  Upgrade-Result
-------- ----- --------------
     1   SUP   Success

EPLDs upgraded.

Module 1 EPLD upgrade is successful.

Dopo il riavvio dello switch, effettuare nuovamente l'accesso e verificare che la nuova versione di EPLD sia stata caricata correttamente.

Mostra esempio

cs2# show version module 1 epld

EPLD Device                     Version
---------------------------------------
MI   FPGA                        0x7
IO   FPGA                        0x19
MI   FPGA2                       0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2

Verificare lo stato di tutte le porte del cluster.

Porte cluster

Verificare che le porte del cluster siano attive e funzionanti su tutti i nodi del cluster:

network port show -ipspace Cluster

Mostra esempio

cluster1::*> network port show -ipspace Cluster

Node: node1-01
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/10000 healthy  false
e7b       Cluster      Cluster          up   9000  auto/10000 healthy  false

Node: node1-02
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/10000 healthy  false
e7b       Cluster      Cluster          up   9000  auto/10000 healthy  false

Node: node1-03
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/100000 healthy false
e7b       Cluster      Cluster          up   9000  auto/100000 healthy false

Node: node1-04
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/100000 healthy false
e7b       Cluster      Cluster          up   9000  auto/100000 healthy false

Verificare lo stato di integrità dello switch dal cluster:

network device-discovery show -protocol cdp

system cluster-switch show -is-monitoring-enabled-operational true

Mostra esempio

cluster1::*> network device-discovery show -protocol cdp

node1-01/cdp
            e10a   cs1(FLMXXXXXXXX)         Ethernet1/16/3    N9K-C9364D-GX2A
            e10b   cs2(FDOXXXXXXXX)         Ethernet1/13/3    N9K-C9364D-GX2A
            e11a   cs1(FLMXXXXXXXX)         Ethernet1/16/4    N9K-C9364D-GX2A
            e11b   cs2(FDOXXXXXXXX)         Ethernet1/13/4    N9K-C9364D-GX2A
            e1a    cs1(FLMXXXXXXXX)         Ethernet1/16/1    N9K-C9364D-GX2A
            e1b    cs2(FDOXXXXXXXX)         Ethernet1/13/1    N9K-C9364D-GX2A
            .
            .
            .
            e7a    cs1(FLMXXXXXXXX)         Ethernet1/16/2    N9K-C9364D-GX2A
            e7b    cs2(FDOXXXXXXXX)         Ethernet1/13/2    N9K-C9364D-GX2A

node1-02/cdp
            e10a   cs1(FLMXXXXXXXX)         Ethernet1/16/3    N9K-C9364D-GX2A
            e10b   cs2(FDOXXXXXXXX)         Ethernet1/13/3    N9K-C9364D-GX2A
            e11a   cs1(FLMXXXXXXXX)         Ethernet1/16/4    N9K-C9364D-GX2A
            e11b   cs2(FDOXXXXXXXX)         Ethernet1/13/4    N9K-C9364D-GX2A
            e1a    cs1(FLMXXXXXXXX)         Ethernet1/16/1    N9K-C9364D-GX2A
            e1b    cs2(FDOXXXXXXXX)         Ethernet1/13/1    N9K-C9364D-GX2A
            .
            .
            .
            e7a    cs1(FLMXXXXXXXX)         Ethernet1/16/2    N9K-C9364D-GX2A
            e7b    cs2(FDOXXXXXXXX)         Ethernet1/13/2    N9K-C9364D-GX2A
.
.
.

cluster1::*> system cluster-switch show -is-monitoring-enabled-operational true
Switch                      Type               Address          Model
--------------------------- ------------------ ---------------- ---------------
cs2(FDOXXXXXXXX)            cluster-network    10.228.137.233   N9K-C9364D-GX2A
     Serial Number: FDOXXXXXXXX
      Is Monitored: true
            Reason: None
  Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                    10.4(2)
    Version Source: CDP/ISDP


cs1(FLMXXXXXXXX)             cluster-network   10.228.137.253   N9K-C9364D-GX2A
     Serial Number: FLMXXXXXXXX
      Is Monitored: true
            Reason: None
  Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                    10.4(2)
    Version Source: CDP/ISDP

Porte HA
1. Verificare che tutte le porte HA siano attive e in stato di integrità:
  
  ha interconnect status show -node <node-name>

Mostra esempio

cluster1::*> ha interconnect status show -node node1-01
  (system ha interconnect status show)

                       Node: node1-01
              Link 0 Status: up
              Link 1 Status: up
           Is Link 0 Active: true
           Is Link 1 Active: true
         IC RDMA Connection: up
                       Slot: 0
             Debug Firmware: no


Interconnect Port 0 :
                  Port Name: e1a-17
                        MTU: 4096
           Link Information: ACTIVE


Interconnect Port 1 :
                  Port Name: e1b-18
                        MTU: 4096
           Link Information: ACTIVE

cluster1::*> ha interconnect status show -node node1-02
  (system ha interconnect status show)

                       Node: node1-02
              Link 0 Status: up
              Link 1 Status: up
           Is Link 0 Active: true
           Is Link 1 Active: true
         IC RDMA Connection: up
                       Slot: 0
             Debug Firmware: no


Interconnect Port 0 :
                  Port Name: e1a-17
                        MTU: 4096
           Link Information: ACTIVE


Interconnect Port 1 :
                  Port Name: e1b-18
                        MTU: 4096
           Link Information: ACTIVE
.
.
.

Porte di archiviazione

Verificare che tutte le porte di archiviazione siano attive e integre:

storage port show -port-type ENET

Mostra esempio

cluster1::*> storage port show -port-type ENET

                                      Speed
Node               Port Type  Mode    (Gb/s) State    Status
------------------ ---- ----- ------- ------ -------- -----------
node1-01
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
                   e11b ENET  -          100 enabled  online
node1-02
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
                   e11b ENET  -          100 enabled  online
node1-03
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
node1-04
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
                   e11b ENET  -          100 enabled  online
16 entries were displayed.

Porte per ripiani portaoggetti

Verificare che tutte le porte dello scaffale di archiviazione siano attive e in buono stato:

storage shelf port show

Mostra esempio

cluster1::*> storage shelf port show

Shelf ID Module State        Internal?
----- -- ------ ------------ ---------
1.1
       0 A      connected    false
       1 A      connected    false
       2 A      connected    false
       3 A      connected    false
       4 A      connected    false
       5 A      connected    false
       6 A      connected    false
       7 A      connected    false
       8 B      connected    false
       9 B      connected    false
      10 B      connected    false
      11 B      connected    false
      12 B      connected    false
      13 B      connected    false
      14 B      connected    false
      15 B      connected    false

16 entries were displayed.

Verificare lo stato di connessione di tutte le porte dello scaffale di archiviazione:

storage shelf port show -fields remote-device,remote-port,connector-state

Mostra esempio

cluster1::*> storage shelf port show -fields remote-device,remote-port,connector-state

shelf id connector-state remote-port    remote-device
----- -- --------------- -------------- -----------------
1.1   0  connected       Ethernet1/17/1 CX9332D-cs1
1.1   1  connected       Ethernet1/15/1 CX9364D-cs1
1.1   2  connected       Ethernet1/17/2 CX9332D-cs1
1.1   3  connected       Ethernet1/15/2 CX9364D-cs1
1.1   4  connected       Ethernet1/17/3 CX9332D-cs1
1.1   5  connected       Ethernet1/15/3 CX9364D-cs1
1.1   6  connected       Ethernet1/17/4 CX9332D-cs1
1.1   7  connected       Ethernet1/15/4 CX9364D-cs1
1.1   8  connected       Ethernet1/19/1 CX9332D-cs1
1.1   9  connected       Ethernet1/17/1 CX9364D-cs1
1.1   10 connected       Ethernet1/19/2 CX9332D-cs1
1.1   11 connected       Ethernet1/17/2 CX9364D-cs1
1.1   12 connected       Ethernet1/19/3 CX9332D-cs1
1.1   13 connected       Ethernet1/17/3 CX9364D-cs1
1.1   14 connected       Ethernet1/19/4 CX9332D-cs1
1.1   15 connected       Ethernet1/17/4 CX9364D-cs1

16 entries were displayed.

Verificare che il cluster sia integro:

cluster show

Mostra esempio

cluster1::*> cluster show


Node                 Health  Eligibility   Epsilon
-------------------- ------- ------------  ------------
node1-01             true    true          false
node1-02             true    true          false
node1-03             true    true          false
node1-04             true    true          true

4 entries were displayed.

Ripetere i passaggi da 6 a 13 per installare il software NX-OS sullo switch cs1.
Abilita il ripristino automatico sui LIF del cluster.

network interface modify -vserver Cluster -lif * -auto-revert true

Verificare che i LIF del cluster siano tornati alla loro porta home:

network interface show -role cluster

Mostra esempio

cluster1::*> network interface show -role cluster

            Logical         Status     Network            Current     Current Is
Vserver     Interface       Admin/Oper Address/Mask       Node        Port    Home
----------- --------------- ---------- ------------------ ----------- ------- ----
Cluster
            node1-01_clus1  up/up      169.254.36.44/16   node1-01    e7a     true
            node1-01_clus2  up/up      169.254.7.5/16     node1-01    e7b     true
            node1-02_clus1  up/up      169.254.197.206/16 node1-02    e7a     true
            node1-02_clus2  up/up      169.254.195.186/16 node1-02    e7b     true
            node1-03_clus1  up/up      169.254.192.49/16  node1-03    e7a     true
            node1-03_clus2  up/up      169.254.182.76/16  node1-03    e7b     true
            node1-04_clus1  up/up      169.254.59.49/16   node1-04    e7a     true
            node1-04_clus2  up/up      169.254.62.244/16  node1-04    e7b     true

Se alcuni LIF del cluster non sono tornati alle loro porte home, ripristinarli manualmente dal nodo locale:

network interface revert -vserver Cluster -lif <lif-name>

Cosa succederà ora?

Dopo aver installato o aggiornato il software NX-OS,"installare o aggiornare il file di configurazione di riferimento (RCF)" .

Installa o aggiorna il software NX-OS

Creating your file...

Requisiti di revisione

Installa il software