NX-OS ソフトウェアをインストールします
この手順 を使用して、 Nexus 3232C クラスタスイッチに NX-OS ソフトウェアをインストールできます。
要件を確認
-
スイッチ設定の現在のバックアップ。
-
クラスタが完全に機能している(ログにエラーがない、または同様の問題が発生している)。
-
"Cisco Ethernet Switch のページ"。サポートされるONTAP とNX-OSのバージョンについては、スイッチの互換性の表を参照してください。
-
"Cisco Nexus 3000 シリーズスイッチ"。Ciscoスイッチのアップグレードおよびダウングレード手順の詳細については、CiscoのWebサイトで入手可能なソフトウェアおよびアップグレードガイドを参照してください。
ソフトウェアをインストールします
手順 では、 ONTAP コマンドと Cisco Nexus 3000 シリーズスイッチコマンドの両方を使用する必要があります。特に明記されていないかぎり、 ONTAP コマンドを使用します。
の手順 を完了してください "NX-OSおよびRCFのインストールを準備します"をクリックし、次の手順を実行します。
-
クラスタスイッチを管理ネットワークに接続します。
-
「 ping 」コマンドを使用して、 NX-OS ソフトウェアおよび RCF をホストするサーバへの接続を確認します。
例を示します
次の例では、スイッチが IP アドレス 172.19.2.1 のサーバに接続できることを確認します。
cs2# ping 172.19.2.1 Pinging 172.19.2.1 with 0 bytes of data: Reply From 172.19.2.1: icmp_seq = 0. time= 5910 usec.
-
NX-OS ソフトウェアおよび EPLD イメージを Nexus 3232C スイッチにコピーします。
例を示します
cs2# copy sftp: bootflash: vrf management Enter source filename: /code/nxos.9.3.4.bin Enter hostname for the sftp server: 172.19.2.1 Enter username: user1 Outbound-ReKey for 172.19.2.1:22 Inbound-ReKey for 172.19.2.1:22 user1@172.19.2.1's password: sftp> progress Progress meter enabled sftp> get /code/nxos.9.3.4.bin /bootflash/nxos.9.3.4.bin /code/nxos.9.3.4.bin 100% 1261MB 9.3MB/s 02:15 sftp> exit Copy complete, now saving to disk (please wait)... Copy complete. cs2# copy sftp: bootflash: vrf management Enter source filename: /code/n9000-epld.9.3.4.img Enter hostname for the sftp server: 172.19.2.1 Enter username: user1 Outbound-ReKey for 172.19.2.1:22 Inbound-ReKey for 172.19.2.1:22 user1@172.19.2.1's password: sftp> progress Progress meter enabled sftp> get /code/n9000-epld.9.3.4.img /bootflash/n9000-epld.9.3.4.img /code/n9000-epld.9.3.4.img 100% 161MB 9.5MB/s 00:16 sftp> exit Copy complete, now saving to disk (please wait)... Copy complete.
-
NX-OS ソフトウェアの実行中のバージョンを確認します。
'how version (バージョンの表示) '
例を示します
cs2# show version Cisco Nexus Operating System (NX-OS) Software TAC support: http://www.cisco.com/tac Copyright (C) 2002-2019, Cisco and/or its affiliates. All rights reserved. The copyrights to certain works contained in this software are owned by other third parties and used and distributed under their own licenses, such as open source. This software is provided "as is," and unless otherwise stated, there is no warranty, express or implied, including but not limited to warranties of merchantability and fitness for a particular purpose. Certain components of this software are licensed under the GNU General Public License (GPL) version 2.0 or GNU General Public License (GPL) version 3.0 or the GNU Lesser General Public License (LGPL) Version 2.1 or Lesser General Public License (LGPL) Version 2.0. A copy of each such license is available at http://www.opensource.org/licenses/gpl-2.0.php and http://opensource.org/licenses/gpl-3.0.html and http://www.opensource.org/licenses/lgpl-2.1.php and http://www.gnu.org/licenses/old-licenses/library.txt. Software BIOS: version 08.37 NXOS: version 9.3(3) BIOS compile time: 01/28/2020 NXOS image file is: bootflash:///nxos.9.3.3.bin NXOS compile time: 12/22/2019 2:00:00 [12/22/2019 14:00:37] Hardware cisco Nexus3000 C3232C Chassis (Nexus 9000 Series) Intel(R) Xeon(R) CPU E5-2403 v2 @ 1.80GHz with 8154432 kB of memory. Processor Board ID FO??????GD Device name: cs2 bootflash: 53298520 kB Kernel uptime is 0 day(s), 0 hour(s), 3 minute(s), 36 second(s) Last reset at 74117 usecs after Tue Nov 24 06:24:23 2020 Reason: Reset Requested by CLI command reload System version: 9.3(3) Service: plugin Core Plugin, Ethernet Plugin Active Package(s): cs2#
-
NX-OS イメージをインストールします。
イメージファイルをインストールすると、スイッチをリブートするたびにロードされます。
例を示します
cs2# install all nxos bootflash:nxos.9.3.4.bin Installer will perform compatibility check first. Please wait. Installer is forced disruptive Verifying image bootflash:/nxos.9.3.4.bin for boot variable "nxos". [] 100% -- SUCCESS Verifying image type. [] 100% -- SUCCESS Preparing "nxos" version info using image bootflash:/nxos.9.3.4.bin. [] 100% -- SUCCESS Preparing "bios" version info using image bootflash:/nxos.9.3.4.bin. [] 100% -- SUCCESS Performing module support checks. [] 100% -- SUCCESS Notifying services about system upgrade. [] 100% -- SUCCESS Compatibility check is done: Module bootable Impact Install-type Reason ------- ----------------- ------------------- ------------- ------ 1 yes disruptive reset default upgrade is not hitless Images will be upgraded according to following table: Module Image Running-Version(pri:alt) New-Version Upg-Required ------------ ----------- --------------------------------------- -------------------- ------------ 1 nxos 9.3(3) 9.3(4) yes 1 bios v08.37(01/28/2020):v08.32(10/18/2016) v08.37(01/28/2020) no Switch will be reloaded for disruptive upgrade. Do you want to continue with the installation (y/n)? [n] y Install is in progress, please wait. Performing runtime checks. [] 100% -- SUCCESS Setting boot variables. [] 100% -- SUCCESS Performing configuration copy. [] 100% -- SUCCESS Module 1: Refreshing compact flash and upgrading bios/loader/bootrom. Warning: please do not remove or power off the module at this time. [] 100% -- SUCCESS Finishing the upgrade, switch will reboot in 10 seconds. cs2#
-
スイッチのリブート後に、 NX-OS ソフトウェアの新しいバージョンである「 show version 」を確認します
例を示します
cs2# show version Cisco Nexus Operating System (NX-OS) Software TAC support: http://www.cisco.com/tac Copyright (C) 2002-2020, Cisco and/or its affiliates. All rights reserved. The copyrights to certain works contained in this software are owned by other third parties and used and distributed under their own licenses, such as open source. This software is provided "as is," and unless otherwise stated, there is no warranty, express or implied, including but not limited to warranties of merchantability and fitness for a particular purpose. Certain components of this software are licensed under the GNU General Public License (GPL) version 2.0 or GNU General Public License (GPL) version 3.0 or the GNU Lesser General Public License (LGPL) Version 2.1 or Lesser General Public License (LGPL) Version 2.0. A copy of each such license is available at http://www.opensource.org/licenses/gpl-2.0.php and http://opensource.org/licenses/gpl-3.0.html and http://www.opensource.org/licenses/lgpl-2.1.php and http://www.gnu.org/licenses/old-licenses/library.txt. Software BIOS: version 08.37 NXOS: version 9.3(4) BIOS compile time: 01/28/2020 NXOS image file is: bootflash:///nxos.9.3.4.bin NXOS compile time: 4/28/2020 21:00:00 [04/29/2020 06:28:31] Hardware cisco Nexus3000 C3232C Chassis (Nexus 9000 Series) Intel(R) Xeon(R) CPU E5-2403 v2 @ 1.80GHz with 8154432 kB of memory. Processor Board ID FO??????GD Device name: rtpnpi-mcc01-8200-ms-A1 bootflash: 53298520 kB Kernel uptime is 0 day(s), 0 hour(s), 3 minute(s), 14 second(s) Last reset at 196755 usecs after Tue Nov 24 06:37:36 2020 Reason: Reset due to upgrade System version: 9.3(3) Service: plugin Core Plugin, Ethernet Plugin Active Package(s): cs2#
-
EPLD イメージをアップグレードし、スイッチをリブートします。
例を示します
cs2# show version module 1 epld EPLD Device Version --------------------------------------- MI FPGA 0x12 IO FPGA 0x11 cs2# install epld bootflash:n9000-epld.9.3.4.img module 1 Compatibility check: Module Type Upgradable Impact Reason ------ ----------------- ---------- ---------- ------ 1 SUP Yes disruptive Module Upgradable Retrieving EPLD versions.... Please wait. Images will be upgraded according to following table: Module Type EPLD Running-Version New-Version Upg-Required ------ ---- ------------- --------------- ----------- ------------ 1 SUP MI FPGA 0x12 0x12 No 1 SUP IO FPGA 0x11 0x12 Yes The above modules require upgrade. The switch will be reloaded at the end of the upgrade Do you want to continue (y/n) ? [n] y Proceeding to upgrade Modules. Starting Module 1 EPLD Upgrade Module 1 : IO FPGA [Programming] : 100.00% ( 64 of 64 sectors) Module 1 EPLD upgrade is successful. Module Type Upgrade-Result ------ ------------------ -------------- 1 SUP Success Module 1 EPLD upgrade is successful. cs2#
-
スイッチのリブート後、再度ログインし、 EPLD ゴールデンイメージをアップグレードし、スイッチをもう一度リブートします。
例を示します
cs2# install epld bootflash:n9000-epld.9.3.4.img module 1 golden Digital signature verification is successful Compatibility check: Module Type Upgradable Impact Reason ------ ----------------- ---------- ---------- ------ 1 SUP Yes disruptive Module Upgradable Retrieving EPLD versions.... Please wait. The above modules require upgrade. The switch will be reloaded at the end of the upgrade Do you want to continue (y/n) ? [n] y Proceeding to upgrade Modules. Starting Module 1 EPLD Upgrade Module 1 : MI FPGA [Programming] : 100.00% ( 64 of 64 sect) Module 1 : IO FPGA [Programming] : 100.00% ( 64 of 64 sect) Module 1 EPLD upgrade is successful. Module Type Upgrade-Result ------ ------------------ -------------- 1 SUP Success EPLDs upgraded. Module 1 EPLD upgrade is successful. cs2#
-
スイッチのリブート後、ログインして新しいバージョンの EPLD が正常にロードされたことを確認します。
例を示します
cs2# show version module 1 epld EPLD Device Version --------------------------------------- MI FPGA 0x12 IO FPGA 0x12