日本語は機械翻訳による参考訳です。内容に矛盾や不一致があった場合には、英語の内容が優先されます。

NX-OSソフトウェアをインストールまたはアップグレードする

07/17/2026 共同作成者

PDF

Nexus 9336C-FX2 および 9336C-FX2-T クラスタスイッチに NX-OS ソフトウェアをインストールまたはアップグレードするには、次の手順に従います。

始める前に、以下の手順を完了してください。"NX-OSとRCFのインストールの準備" 。

要件の確認

開始する前に

必ず次のことを行ってください：

スイッチで `show install all impact nxos bootflash:<image_name>.bin`コマンドを実行して、新しいNX-OSソフトウェアイメージのインストールまたはアップグレードの影響を確認します。イメージの整合性を検証し、必要な再起動をチェックし、ハードウェアの互換性を評価し、十分なスペースを確認します。
対象となる NX-OS ソフトウェアバージョンのリリースノートを参照して、特定の要件を確認します。
スイッチ構成の最新のバックアップがあることを確認します。
クラスターが完全に機能していることを確認します（ログにエラーや同様の問題がない）。

推奨ドキュメント

"Ciscoイーサネットスイッチページ"

サポートされているONTAPおよび NX-OS バージョンについては、スイッチ互換性表を参照してください。
"ソフトウェアのアップグレードとダウングレードのガイド"

ソフトウェアのアップグレードおよびダウングレードガイドについては、Cisco のウェブサイトを参照してください。
"Cisco Nexus 9000 および 3000 のアップグレードと ISSU マトリックス"

現在のリリースとターゲットリリースに基づいて、Nexus 9000 シリーズスイッチ上のCisco NX-OS ソフトウェアの中断を伴うアップグレード/ダウングレードに関する情報を提供します。

このページで、「Disruptive Upgrade」を選択し、ドロップダウンリストから現在のリリースとターゲットリリースを選択します。

例について

この手順の例で使用するスイッチとノードの名前は次のとおりです。

2 つのCiscoスイッチの名前は cs1 と cs2 です。
ノード名は、cluster1-01、cluster1-02、cluster1-03、cluster1-04 です。
クラスタ LIF 名は、cluster1-01_clus1、cluster1-01_clus2、cluster1-02_clus1、cluster1-02_clus2、cluster1-03_clus1、cluster1-03_clus2、cluster1-04_clus1、cluster1-04_clus2 です。
その `cluster1::*>`プロンプトはクラスターの名前を示します。

ソフトウェアをインストールする

この手順では、Cisco Nexus 9000 シリーズスイッチのコマンドが指定されている場合を除き、ONTAP コマンドを使用してください。

手順

クラスタスイッチを管理ネットワークに接続します。
ping コマンドを使用して、NX-OS ソフトウェアと RCF をホストしているサーバーへの接続を確認します。

ping <IP address> vrf management
例を表示
次の例では、スイッチがIPアドレス172.19.2.1のサーバに接続できることを確認します。
cs2# ping 172.19.2.1 vrf management Pinging 172.19.2.1 with 0 bytes of data: Reply From 172.19.2.1: icmp_seq = 0. time= 5910 usec.

クラスタースイッチに接続されている各ノード上のクラスターポートを表示します。

network device-discovery show

例を表示

cluster1::*> network device-discovery show
Node/       Local  Discovered
Protocol    Port   Device (LLDP: ChassisID)  Interface         Platform
----------- ------ ------------------------- ----------------- --------------
cluster1-01/cdp
            e0a    cs1                       Ethernet1/7       N9K-C9336C-FX2
            e0b    cs2                       Ethernet1/7       N9K-C9336C-FX2
cluster1-02/cdp
            e0a    cs1                       Ethernet1/8       N9K-C9336C-FX2
            e0b    cs2                       Ethernet1/8       N9K-C9336C-FX2
cluster1-03/cdp
            e0a    cs1                       Ethernet1/1/1     N9K-C9336C-FX2
            e0b    cs2                       Ethernet1/1/1     N9K-C9336C-FX2
cluster1-04/cdp
            e0a    cs1                       Ethernet1/1/2     N9K-C9336C-FX2
            e0b    cs2                       Ethernet1/1/2     N9K-C9336C-FX2
cluster1::*>

各クラスタポートの管理ステータスと動作ステータスを確認します。

すべてのクラスターポートが正常な状態で up していることを確認します。

network port show -ipspace Cluster

例を表示

cluster1::*> network port show -ipspace Cluster

Node: cluster1-01
                                                                        Ignore
                                                  Speed(Mbps)  Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper   Status   Status
--------- ------------ ---------------- ---- ---- ------------ -------- ------
e0a       Cluster      Cluster          up   9000  auto/100000 healthy  false
e0b       Cluster      Cluster          up   9000  auto/100000 healthy  false

Node: cluster1-02
                                                                        Ignore
                                                  Speed(Mbps)  Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper   Status   Status
--------- ------------ ---------------- ---- ---- ------------ -------- ------
e0a       Cluster      Cluster          up   9000  auto/100000 healthy  false
e0b       Cluster      Cluster          up   9000  auto/100000 healthy  false

Node: cluster1-03

                                                                        Ignore
                                                  Speed(Mbps)  Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper   Status   Status
--------- ------------ ---------------- ---- ---- ------------ -------- ------
e0a       Cluster      Cluster          up   9000  auto/100000 healthy  false
e0b       Cluster      Cluster          up   9000  auto/100000 healthy  false

Node: cluster1-04
                                                                        Ignore
                                                  Speed(Mbps)  Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper   Status   Status
--------- ------------ ---------------- ---- ---- ------------ -------- ------
e0a       Cluster      Cluster          up   9000  auto/100000 healthy  false
e0b       Cluster      Cluster          up   9000  auto/100000 healthy  false
cluster1::*>

すべてのクラスタインターフェイス (LIF) がホームポート上にあることを確認します。

network interface show -vserver Cluster

例を表示

cluster1::*> network interface show -vserver Cluster
            Logical            Status     Network            Current             Current Is
Vserver     Interface          Admin/Oper Address/Mask       Node                Port    Home
----------- ------------------ ---------- ------------------ ------------------- ------- ----
Cluster
            cluster1-01_clus1  up/up      169.254.3.4/23     cluster1-01         e0b     true
            cluster1-01_clus2  up/up      169.254.3.5/23     cluster1-01         e0b     true
            cluster1-02_clus1  up/up      169.254.3.8/23     cluster1-02         e0b     true
            cluster1-02_clus2  up/up      169.254.3.9/23     cluster1-02         e0b     true
            cluster1-03_clus1  up/up      169.254.1.3/23     cluster1-03         e0b     true
            cluster1-03_clus2  up/up      169.254.1.1/23     cluster1-03         e0b     true
            cluster1-04_clus1  up/up      169.254.1.6/23     cluster1-04         e0b     true
            cluster1-04_clus2  up/up      169.254.1.7/23     cluster1-04         e0b     true
cluster1::*>

クラスターが両方のクラスタースイッチの情報を表示することを確認します。

system cluster-switch show -is-monitoring-enabled-operational true

例を表示

cluster1::*> system cluster-switch show -is-monitoring-enabled-operational true
Switch                      Type               Address          Model
--------------------------- ------------------ ---------------- --------------
cs1                         cluster-network    10.233.205.90    N9K-C9336C-FX2
     Serial Number: FOCXXXXXXGD
      Is Monitored: true
            Reason: None
  Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                    9.3(5)
    Version Source: CDP

cs2                         cluster-network    10.233.205.91    N9K-C9336C-FX2
     Serial Number: FOCXXXXXXGS
      Is Monitored: true
            Reason: None
  Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                    9.3(5)
    Version Source: CDP
cluster1::*>

クラスタLIFで自動リバートを無効にします。クラスタ LIF はパートナークラスタスイッチにフェイルオーバーし、対象スイッチでアップグレード手順を実行する間、そこに残ります。

network interface modify -vserver Cluster -lif * -auto-revert false
NX-OS ソフトウェアと EPLD イメージをダウンロードしてインストールします。手順は、現在の NX-OS バージョンとターゲットの NX-OS バージョンによって異なる場合があります。

ご自身の状況に該当するタブを選択してください。
- バージョン10.4(5)(M)にアップグレード
- 10.4(5)(M)以前のバージョンから10.5(3)(F)以降のバージョンにアップグレードする
- バージョン10.5(3)(F)からそれ以降のバージョンにアップグレードする

バージョン10.4(5)(M)にアップグレード

NX-OSソフトウェアとEPLDイメージをNexus 9336C-FX2スイッチにコピーします。

copy <protocol>: bootflash: vrf management

例

cs2# *copy sftp: bootflash: vrf management*
Enter source filename: */code/nxos.10.4.5.M.bin*
Enter hostname for the sftp server: *172.19.2.1*
Enter username: *user1*

Outbound-ReKey for 172.19.2.1:22
Inbound-ReKey for 172.19.2.1:22
user1@172.19.2.1's password:
sftp> *progress*
Progress meter enabled
sftp> *get /code/nxos.10.4.5.M.bin /bootflash/nxos.10.4.5.M.bin*
/code/nxos.10.4.5.M.bin  100% 1261MB   9.3MB/s   02:15
sftp> *exit*
Copy complete, now saving to disk (please wait)...
Copy complete.


cs2# *copy sftp: bootflash: vrf management*
Enter source filename: */code/n9000-epld.10.4.5.M.img*
Enter hostname for the sftp server: *172.19.2.1*
Enter username: *user1*

Outbound-ReKey for 172.19.2.1:22
Inbound-ReKey for 172.19.2.1:22
user1@172.19.2.1's password:
sftp> *progress*
Progress meter enabled
sftp> *get /code/n9000-epld.10.4.5.M.img /bootflash/n9000-epld.10.4.5.M.img*
/code/n9000-epld.10.4.5.M.img  100%  161MB   9.5MB/s   00:16
sftp> *exit*
Copy complete, now saving to disk (please wait)...
Copy complete.

NX-OSソフトウェアの実行中のバージョンを確認します。

show version

例

cs2# *show version*
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (C) 2002-2020, Cisco and/or its affiliates.
All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under their own
licenses, such as open source.  This software is provided "as is," and unless
otherwise stated, there is no warranty, express or implied, including but not
limited to warranties of merchantability and fitness for a particular purpose.
Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or
GNU General Public License (GPL) version 3.0  or the GNU
Lesser General Public License (LGPL) Version 2.1 or
Lesser General Public License (LGPL) Version 2.0.
A copy of each such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://opensource.org/licenses/gpl-3.0.html and
http://www.opensource.org/licenses/lgpl-2.1.php and
http://www.gnu.org/licenses/old-licenses/library.txt.

Software
  BIOS: version 08.38
  NXOS: version 10.3(5)
  BIOS compile time:  05/29/2020
  NXOS image file is: bootflash:///nxos.10.3.5.bin
  NXOS compile time:  4/28/2020 21:00:00 [04/29/2020 02:28:31]


Hardware
  cisco Nexus9000 C9336C-FX2 Chassis
  Intel(R) Xeon(R) CPU E5-2403 v2 @ 1.80GHz with 8154432 kB of memory.
  Processor Board ID FOC20291J6K

  Device name: cs2
  bootflash:   53298520 kB
Kernel uptime is 0 day(s), 0 hour(s), 3 minute(s), 42 second(s)


Last reset at 157524 usecs after Mon Nov  2 18:32:06 2020
  Reason: Reset Requested by CLI command reload
  System version: 9.3(4)
  Service:

plugin
  Core Plugin, Ethernet Plugin

Active Package(s):


cs2#

NX-OSイメージをインストールします。

イメージファイルをインストールすると、スイッチをリブートするたびにこのファイルがロードされます。

install all nxos bootflash:<bin_file_name>

例

cs2# *install all nxos bootflash:nxos.10.4.5.M.bin*

Installer will perform compatibility check first. Please wait.
Installer is forced disruptive

Verifying image bootflash:/nxos.10.4.5.M.bin for boot variable "nxos".
[] 100% -- SUCCESS

Verifying image type.
[] 100% -- SUCCESS

Preparing "nxos" version info using image bootflash:/nxos.10.4.5.M.bin.
[] 100% -- SUCCESS

Preparing "bios" version info using image bootflash:/nxos.10.4.5.M.bin.
[] 100% -- SUCCESS

Performing module support checks.
[] 100% -- SUCCESS

Notifying services about system upgrade.
[] 100% -- SUCCESS


Compatibility check is done:
Module  Bootable  Impact          Install-type  Reason
------  --------  --------------- ------------  ---------
  1     yes       Disruptive      Reset         Default upgrade is not hitless


Images will be upgraded according to following table:

Module   Image    Running-Version(pri:alt)                 New-Version         Upg-Required
------- --------- ---------------------------------------- ------------------- ------------
  1      nxos     10.3(5)                                   10.4.5(M)              yes
  1      bios     v08.37(01/28/2020):v08.23(09/23/2015)    v08.38(05/29/2020)      yes


Switch will be reloaded for disruptive upgrade.

Do you want to continue with the installation (y/n)? [n] *y*

Install is in progress, please wait.

Performing runtime checks.
[] 100% -- SUCCESS

Setting boot variables.
[] 100% -- SUCCESS

Performing configuration copy.
[] 100% -- SUCCESS

Module 1: Refreshing compact flash and upgrading bios/loader/bootrom.
Warning: please do not remove or power off the module at this time.
[] 100% -- SUCCESS

Finishing the upgrade, switch will reboot in 10 seconds.

スイッチを再起動した後、NX-OS ソフトウェアの新しいバージョンを確認します。

show version

例

cs2# *show version*

Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (C) 2002-2020, Cisco and/or its affiliates.
All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under their own
licenses, such as open source.  This software is provided "as is," and unless
otherwise stated, there is no warranty, express or implied, including but not
limited to warranties of merchantability and fitness for a particular purpose.
Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or
GNU General Public License (GPL) version 3.0  or the GNU
Lesser General Public License (LGPL) Version 2.1 or
Lesser General Public License (LGPL) Version 2.0.
A copy of each such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://opensource.org/licenses/gpl-3.0.html and
http://www.opensource.org/licenses/lgpl-2.1.php and
http://www.gnu.org/licenses/old-licenses/library.txt.

Software
  BIOS: version 05.33
  NXOS: version 10.4.5(M)  BIOS compile time:  09/08/2018
  NXOS image file is: bootflash:///nxos.10.4.5.M.bin
  NXOS compile time:  11/4/2018 21:00:00 [11/05/2018 06:11:06]


Hardware
  cisco Nexus9000 C9336C-FX2 Chassis
  Intel(R) Xeon(R) CPU E5-2403 v2 @ 1.80GHz with 8154432 kB of memory.
  Processor Board ID FOC20291J6K

  Device name: cs2
  bootflash:   53298520 kB
Kernel uptime is 0 day(s), 0 hour(s), 3 minute(s), 42 second(s)

Last reset at 277524 usecs after Mon Nov  2 22:45:12 2020
  Reason: Reset due to upgrade
  System version: 10.4.5(M)
  Service:

plugin
  Core Plugin, Ethernet Plugin

Active Package(s):

EPLDイメージをアップグレードし、スイッチをリブートします。

show version module 1 epld

install epld bootflash:<image_file_name> module all

例

cs2# *show version module 1 epld*

EPLD Device                     Version
---------------------------------------
MI   FPGA                        0x7
IO   FPGA                        0x17
MI   FPGA2                       0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2

cs2# *install epld bootflash:n9000-epld.10.4.5.M.img module all*
Compatibility check:
Module  Type      Upgradable        Impact      Reason
------  --------- ----------------- ----------- -----------
     1  SUP       Yes               disruptive  Module Upgradable

Retrieving EPLD versions.... Please wait.
Images will be upgraded according to following table:
Module  Type   EPLD              Running-Version   New-Version  Upg-Required
------- ------ ----------------- ----------------- ------------ ------------
     1  SUP    MI FPGA           0x07              0x07         No
     1  SUP    IO FPGA           0x17              0x19         Yes
     1  SUP    MI FPGA2          0x02              0x02         No
The above modules require upgrade.
The switch will be reloaded at the end of the upgrade
Do you want to continue (y/n) ?  [n] *y*

Proceeding to upgrade Modules.

Starting Module 1 EPLD Upgrade

Module 1 : IO FPGA [Programming] : 100.00% (     64 of      64 sectors)
Module 1 EPLD upgrade is successful.
Module   Type  Upgrade-Result
-------- ----- --------------
     1   SUP   Success

EPLDs upgraded.

Module 1 EPLD upgrade is successful.

スイッチのリブート後に再度ログインし、新しいバージョンのEPLDが正常にロードされたことを確認します。

show version module 1 epld

例

cs2# *show version module 1 epld*

EPLD Device                     Version
---- -------------------------- -------
MI   FPGA                        0x7
IO   FPGA                        0x19
MI   FPGA2                       0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2

10.4(5)(M)以前のバージョンから10.5(3)(F)以降のバージョンにアップグレードする

NX-OSソフトウェアとEPLDイメージをNexus 9336C-FX2スイッチにコピーします。

copy <protocol>: bootflash: vrf management

例

cs2# *copy sftp: bootflash: vrf management*
Enter source filename: */code/nxos.10.5.3.F.bin*
Enter hostname for the sftp server: *172.19.2.1*
Enter username: *user1*

Outbound-ReKey for 172.19.2.1:22
Inbound-ReKey for 172.19.2.1:22
user1@172.19.2.1's password:
sftp> *progress*
Progress meter enabled
sftp> *get /code/nxos.10.5.3.F.bin /bootflash/nxos.10.5.3.F.bin*
/code/nxos.10.5.3.F.bin  100% 1261MB   9.3MB/s   02:15
sftp> *exit*
Copy complete, now saving to disk (please wait)...
Copy complete.


cs2# *copy sftp: bootflash: vrf management*
Enter source filename: */code/n9000-epld.10.5.3.F.img*
Enter hostname for the sftp server: *172.19.2.1*
Enter username: *user1*

Outbound-ReKey for 172.19.2.1:22
Inbound-ReKey for 172.19.2.1:22
user1@172.19.2.1's password:
sftp> *progress*
Progress meter enabled
sftp> *get /code/n9000-epld.10.5.3.F.img /bootflash/n9000-epld.10.5.3.F.img*
/code/n9000-epld.10.5.3.F.img  100%  161MB   9.5MB/s   00:16
sftp> *exit*
Copy complete, now saving to disk (please wait)...
Copy complete.

NX-OSソフトウェアの実行中のバージョンを確認します。

show version

例

cs2# *show version*
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (C) 2002-2020, Cisco and/or its affiliates.
All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under their own
licenses, such as open source.  This software is provided "as is," and unless
otherwise stated, there is no warranty, express or implied, including but not
limited to warranties of merchantability and fitness for a particular purpose.
Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or
GNU General Public License (GPL) version 3.0  or the GNU
Lesser General Public License (LGPL) Version 2.1 or
Lesser General Public License (LGPL) Version 2.0.
A copy of each such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://opensource.org/licenses/gpl-3.0.html and
http://www.opensource.org/licenses/lgpl-2.1.php and
http://www.gnu.org/licenses/old-licenses/library.txt.

Software
  BIOS: version 08.38
  NXOS: version 10.5.3(F)
  BIOS compile time:  05/29/2020
  NXOS image file is: bootflash:///nxos.10.5.3.F.bin
  NXOS compile time:  4/28/2020 21:00:00 [04/29/2020 02:28:31]


Hardware
  cisco Nexus9000 C9336C-FX2 Chassis
  Intel(R) Xeon(R) CPU E5-2403 v2 @ 1.80GHz with 8154432 kB of memory.
  Processor Board ID FOC20291J6K

  Device name: cs2
  bootflash:   53298520 kB
Kernel uptime is 0 day(s), 0 hour(s), 3 minute(s), 42 second(s)


Last reset at 157524 usecs after Mon Nov  2 18:32:06 2020
  Reason: Reset Requested by CLI command reload
  System version: 9.3(4)
  Service:

plugin
  Core Plugin, Ethernet Plugin

Active Package(s):

cs2#

NX-OSおよびEPLDイメージをインストールします。

NX-OS 10.5(3)(F)以降にアップグレードしても、EPLDイメージは自動的に更新されません。アップグレードが完了し、スイッチが再起動したら、同じアップグレード `install all`コマンドを再度実行する必要があります。

2回目のアップグレード処理では検証が行われますが、NX-OS のアップグレードはスキップされ、EPLD イメージのみが更新されます。
既にNX-OS 10.5(3)(F)以降にアップグレード済みの場合、両方のイメージが同時に更新されます。

+ イメージファイルをインストールすると、スイッチをリブートするたびにこのファイルがロードされます。

+ 以下の手順は、NX-OS 10.4(5)(M) から 10.5(3)(F) へのアップグレードを示しています。最初の処理では NX-OS のアップグレードが実行され、2回目の処理では EPLD イメージのアップグレードが実行されます。

+ install all nxos bootflash:<nxos_image.bin>

+ .例

Details

cs2# *install all nxos bootflash:nxos.10.5.3.F.bin*   <---- 1st pass updates NX-OS only

Installer will perform compatibility check first. Please wait.
Installer is forced disruptive

Verifying image bootflash:/nxos.10.5.3.F.bin for boot variable "nxos".
[####################] 100% -- SUCCESS

Verifying image type.
[####################] 100% -- SUCCESS

Preparing "nxos" version info using image bootflash:/nxos.10.5.3.F.bin.
[####################] 100% -- SUCCESS

Preparing "bios" version info using image bootflash:/nxos.10.5.3.F.bin.
[####################] 100% -- SUCCESS

Performing module support checks.
[####################] 100% -- SUCCESS

Notifying services about system upgrade.
[####################] 100% -- SUCCESS


Compatibility check is done:
Module  Bootable  Impact          Install-type  Reason
------  --------  --------------- ------------  ---------
1       yes       Disruptive      Reset         Default upgrade is not hitless


Images will be upgraded according to following table:

Module   Image    Running-Version(pri:alt)                 New-Version          Upg-Required
------- --------- ---------------------------------------- -------------------- ------------ 
1        nxos     10.4(5)(M)                                10.5(3)(F)            yes
1        bios     v05.47(04/28/2022):v05.47(04/28/2022)    v05.53(01/22/2025)     yes

Switch will be reloaded for disruptive upgrade.

Do you want to continue with the installation (y/n)? [n] *y*

Install is in progress, please wait.

Performing runtime checks.
[####################] 100% -- SUCCESS

Setting boot variables.
[####################] 100% -- SUCCESS

Performing configuration copy.
[####################] 100% -- SUCCESS

Module 1: Refreshing compact flash and upgrading bios/loader/bootrom.
Warning: please do not remove or power off the module at this time.
[####################] 100% -- SUCCESS
[####################] 100% -- SUCCESS

Finishing the upgrade, switch will reboot in 10 seconds.


cs2# *install all nxos bootflash:nxos.10.5.3.F.bin*   <---- 2nd pass updates EPLD image only
 
Installer will perform compatibility check first. Please wait. 
Installer is forced disruptive
 
Verifying image bootflash:/nxos.10.5.3.F.bin for boot variable "nxos".
[####################] 100% -- SUCCESS
 
Verifying EPLD/FPGA image //bootflash/nxos.10.5.3.F.bin.
[####################] 100% -- SUCCESS
 
Verifying image type.
[####################] 100% -- SUCCESS
 
Preparing "nxos" version info using image bootflash:/nxos.10.5.3.F.bin.
[####################] 100% -- SUCCESS
 
Preparing "bios" version info using image bootflash:/nxos.10.5.3.F.bin.
[####################] 100% -- SUCCESS

Performing module support checks.
[####################] 100% -- SUCCESS
 
Notifying services about system upgrade.
[####################] 100% -- SUCCESS
 

Compatibility check is done:
Module  bootable  Impact          Install-type  Reason
------  --------  --------------  ------------  ------
1       yes       disruptive      reset         default upgrade is not hitless
27      yes       disruptive      none          default upgrade is not hitless
 
 
Images will be upgraded according to following table:
Module    Image                  Running-Version(pri:alt)              New-Version         Upg-Required
--------  ---------------------  ------------------------------------- -----------------  ------------
27        nxos                   10.4(5)(M)                            10.5(3)(F)             no
27        bios                   v05.53(01/22/2025):v05.47(04/28/2022) v05.53(01/22/2025)    no
 
 
FPGA microcode will be upgraded according to following table:
Module  Type  EPLD               Running-Version  Flashed-Version*   New-Version  Upg-Required
------  ----  -----------------  ---------------  ----------------   -----------  ------------
27      SUP   MI FPGA            0x5              0x5                0x5          No
27      SUP   IO FPGA            0x17             0x17               0x18         Yes

If Running-Version and Flashed-Version are different it implies that the system has not yet been reloaded for the new version to take effect.
 
EPLD Upgrade may result in multiple modules going offline.
 
 
Switch will be reloaded for disruptive upgrade.
 
Do you want to continue with the installation (y/n)?  [n] *y*
 
Install is in progress, please wait.

Setting boot variables.
[####################] 100% -- SUCCESS
 
Performing configuration copy.
[####################] 100% -- SUCCESS
Performing configuration copy.
[####################] 100% -- SUCCESS
 
Module 1: Refreshing compact flash and upgrading bios/loader/bootrom.
Warning: please do not remove or power off the module at this time.

Module 1: Refreshing compact flash and upgrading bios/loader/bootrom.
Warning: please do not remove or power off the module at this time.
[####################] 100% -- SUCCESS
 
Module 27: Refreshing compact flash and upgrading bios/loader/bootrom.
Warning: please do not remove or power off the module at this time.

Module 27: Refreshing compact flash and upgrading bios/loader/bootrom.
Warning: please do not remove or power off the module at this time.
[####################] 100% -- SUCCESS
 
EPLD/FPGA upgrade can take up to 4 mins.

Performing EPLD/FPGA upgrade.
[####################] 100% -- SUCCESS
 
Install has been successful.

スイッチを再起動した後、NX-OS ソフトウェアの新しいバージョンを確認します。

show version

例

cs2# *show version*
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (C) 2002-2020, Cisco and/or its affiliates.
All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under their own
licenses, such as open source.  This software is provided "as is," and unless
otherwise stated, there is no warranty, express or implied, including but not
limited to warranties of merchantability and fitness for a particular purpose.
Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or
GNU General Public License (GPL) version 3.0  or the GNU
Lesser General Public License (LGPL) Version 2.1 or
Lesser General Public License (LGPL) Version 2.0.
A copy of each such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://opensource.org/licenses/gpl-3.0.html and
http://www.opensource.org/licenses/lgpl-2.1.php and
http://www.gnu.org/licenses/old-licenses/library.txt.

Software
  BIOS: version 05.33
  NXOS: version 10.5.3(f)
  BIOS compile time:  09/08/2018
  NXOS image file is: bootflash:///nxos.10.5.3.F.bin
  NXOS compile time:  11/4/2018 21:00:00 [11/05/2018 06:11:06]


Hardware
  cisco Nexus9000 C9336C-FX2 Chassis
  Intel(R) Xeon(R) CPU E5-2403 v2 @ 1.80GHz with 8154432 kB of memory.
  Processor Board ID FOC20291J6K

  Device name: cs2
  bootflash:   53298520 kB
Kernel uptime is 0 day(s), 0 hour(s), 3 minute(s), 42 second(s)

Last reset at 277524 usecs after Mon Nov  2 22:45:12 2020
  Reason: Reset due to upgrade
  System version: 9.3(4)
  Service:

plugin
  Core Plugin, Ethernet Plugin

Active Package(s):

スイッチのリブート後に再度ログインし、新しいバージョンのEPLDが正常にロードされたことを確認します。

show version module 1 epld

例

cs2# *show version module 1 epld*

EPLD Device                     Version
---------------------------------------
MI   FPGA                        0x7
IO   FPGA                        0x19
MI   FPGA2                       0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2

NX-OSとEPLDのイメージを最初のスイッチにコピーします。

copy <protocol>: bootflash: vrf management

この例ではsftpを使用しています。

例

cs2# *copy sftp: bootflash: vrf management*
Enter source filename: *nxos64-cs.10.5.4.M.bin*
Enter hostname for the sftp server: *172.19.2.1*
Enter username: *user1*

Outbound-ReKey for 172.19.2.1:22
Inbound-ReKey for 172.19.2.1:22
user1@172.19.2.1's password:
sftp> *progress*
Progress meter enabled
sftp> *get /code/nxos64-cs.10.5.4.M.bin /bootflash/nxos64-cs.10.5.4.M.bin*
/code/nxos64-cs.10.5.4.M.bin  100% 1261MB   9.3MB/s   02:15
sftp> *exit*
Copy complete, now saving to disk (please wait)...
Copy complete.

NX-OS の実行中のバージョンを確認します：

show version

例

cs2# *show version*
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (C) 2002-2025, Cisco and/or its affiliates.
All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under their own
licenses, such as open source.  This software is provided "as is," and unless
otherwise stated, there is no warranty, express or implied, including but not
limited to warranties of merchantability and fitness for a particular purpose.
Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or
GNU General Public License (GPL) version 3.0  or the GNU
Lesser General Public License (LGPL) Version 2.1 or
Lesser General Public License (LGPL) Version 2.0.
A copy of each such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://opensource.org/licenses/gpl-3.0.html and
http://www.opensource.org/licenses/lgpl-2.1.php and
http://www.gnu.org/licenses/old-licenses/library.txt.


Software
  BIOS: version 01.14
  NXOS: version 10.5(3)(F) [Feature Release]
  Host NXOS: version 10.5(3)(F)
  BIOS compile time:  11/25/2024
  NXOS image file is: bootflash:///nxos.10.5.3.F.bin
  NXOS compile time:  02/27/2026 12:00:00 [03/14/2026 05:25:50]
  NXOS boot mode: LXC


Hardware
  cisco  Nexus9000 C9336C-FX2 Chassis
  Intel(R) Xeon(R) CPU D-1633N @ 2.50GHz with 32802156 kB of memory.
  Processor Board ID FLMXXXXXXXX
  Device name: cs2
  bootflash:  115802886 kB


Kernel uptime is 5 day(s), 2 hour(s), 13 minute(s), 21 second(s)


Last reset at 3580 usecs after Thu Mar 5 15:55:08 2026
  Reason: Reset Requested by CLI command reload
  System version: 10.5.3(f)
  Service:


plugin
  Core Plugin, Ethernet Plugin


Active Package(s):

cs2#

NX-OSとEPLDイメージをインストールします。

イメージファイルをインストールすると、スイッチをリブートするたびにこのファイルがロードされます。

install all nxos bootflash:<nxos_image.bin>

この例では、NX-OS バージョン 10.5(4)(M) を使用しています。

例

cs2# *install all nxos bootflash:nxos64-cs.10.5.4.M.bin*

Installer will perform compatibility check first. Please wait.
Installer is forced disruptive

Verifying image bootflash:/nxos64-cs.10.5.4.M.bin for boot variable "nxos".
[####################] 100% -- SUCCESS

Verifying image type.
[####################] 100% -- SUCCESS

Preparing "nxos" version info using image bootflash:/nxos64-cs.10.5.4.M.bin.
[####################] 100% -- SUCCESS

Preparing "bios" version info using image bootflash:/nxos64-cs.10.5.4.M.bin.
[####################] 100% -- SUCCESS

Performing module support checks.
[####################] 100% -- SUCCESS

Notifying services about system upgrade.
[####################] 100% -- SUCCESS


Compatibility check is done:
Module  Bootable  Impact          Install-type  Reason
------  --------  --------------- ------------  ---------
  1     yes       Disruptive      Reset         Default upgrade is not hitless


Images will be upgraded according to following table:

Module   Image    Running-Version(pri:alt)            New-Version         Upg-Required
------- --------- ----------------------------------- ------------------- ------------
  1      nxos     10.5(3)(F)                          10.5(4)(M)          Yes
  1      bios     <current_version>                   <new_version>       No


Switch will be reloaded for disruptive upgrade.

Do you want to continue with the installation (y/n)? [n] *y*

Install is in progress, please wait.

Performing runtime checks.
[####################] 100% -- SUCCESS

Setting boot variables.
[####################] 100% -- SUCCESS

Performing configuration copy.
[####################] 100% -- SUCCESS

Module 1: Refreshing compact flash and upgrading bios/loader/bootrom.
Warning: please do not remove or power off the module at this time.
[####################] 100% -- SUCCESS

Finishing the upgrade, switch will reboot in 10 seconds.

スイッチの再起動後、NX-OS の新しいバージョンを確認します：

show version

例

cs2# *show version*
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (C) 2002-2025, Cisco and/or its affiliates.
All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under their own
licenses, such as open source.  This software is provided "as is," and unless
otherwise stated, there is no warranty, express or implied, including but not
limited to warranties of merchantability and fitness for a particular purpose.
Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or
GNU General Public License (GPL) version 3.0  or the GNU
Lesser General Public License (LGPL) Version 2.1 or
Lesser General Public License (LGPL) Version 2.0.
A copy of each such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://opensource.org/licenses/gpl-3.0.html and
http://www.opensource.org/licenses/lgpl-2.1.php and
http://www.gnu.org/licenses/old-licenses/library.txt.


Software
  BIOS: version 01.14
  NXOS: version 10.5(4)(M) [Feature Release]
  Host NXOS: version 10.5(4)(M)
  BIOS compile time:  11/25/2024
  NXOS image file is: bootflash:///nxos64-cs.10.5.4.M.bin
  NXOS compile time:  05/30/2026 12:00:00 [06/14/2026 05:25:50]
  NXOS boot mode: LXC


Hardware
  cisco Nexus9000 C9336C-FX2 Chassis
  Intel(R) Xeon(R) CPU D-1633N @ 2.50GHz with 32802156 kB of memory.
  Processor Board ID FLMXXXXXXXX
  Device name: cs2
  bootflash:  115802886 kB


Kernel uptime is 5 day(s), 2 hour(s), 13 minute(s), 21 second(s)


Last reset at 3580 usecs after Thu Jun 5 15:55:08 2026
  Reason: Reset Requested by CLI command reload
  System version: 10.5(4)(M)
  Service:


plugin
  Core Plugin, Ethernet Plugin


Active Package(s):

新しいバージョンの EPLD が正常にロードされたことを確認します。

show install epld status

この例では、EPLD バージョン 10.5(4)(M) を使用しています。

例

cs2# *show install epld status*

1) Module 2 upgraded on Mon May  4 09:17:08 2026 (631239  us)
EPLD Install Image: EPLD image file 10.5.4.M. built on Fri Apr 24 19:49:50 2026

Status: EPLD Upgrade was Successful

EPLD                             Curr Ver       Old Ver
-------------------------------------------------------
MI FPGA                         0x10014         0x1000b
IO FPGA                         0x10033         0x10006

2) Module 27 upgraded on Wed Apr  1 15:03:13 2026 (193093  us)
EPLD Install Image: EPLD image file 10.5.4.M. built on Mon Mar 16 03:28:47 2026

Status: EPLD Upgrade was Successful

EPLD                            Curr Ver        Old Ver
-------------------------------------------------------
IO FPGA                         0x1002d         0x10020

3) Module 28 upgraded on Wed Apr  1 14:59:53 2026 (843907  us)
EPLD Install Image: EPLD image file 10.5.4.M. built on Mon Mar 16 03:28:47 2026

Status: EPLD Upgrade was Successful

EPLD                            Curr Ver        Old Ver
-------------------------------------------------------
IO FPGA                         0x1002d         0x10020

4) Module 27 upgraded on Fri Mar 27 21:55:55 2026 (132290  us)
EPLD Install Image: EPLD image file 10.5.4.M. built on Fri Dec 12 11:15:18 2025

Status: EPLD Upgrade was Successful

EPLD                            Curr Ver        Old Ver
-------------------------------------------------------
FM-19 FPGA                      0x10006         0x10000
FM-20 FPGA                      0x10006         0x10000
FM-21 FPGA                      0x10006         0x10000
FM-22 FPGA                      0x10006         0x10000
FM-23 FPGA                      0x10006         0x10000
FM-24 FPGA                      0x10006         0x10000
FM-25 FPGA                      0x10006         0x10000
FM-26 FPGA                      0x10006         0x10000

5) Module 27 upgraded on Fri Mar 27 21:50:16 2026 (  4899  us)
EPLD Install Image: EPLD image file 10.5.4.M. built on Fri Dec 12 11:15:18 2025

Status: EPLD Upgrade was Successful

EPLD                            Curr Ver        Old Ver
-------------------------------------------------------
FM-19 FPGA                      0x10006         0x10000
FM-20 FPGA                      0x10006         0x10000
FM-21 FPGA                      0x10006         0x10000
FM-22 FPGA                      0x10006         0x10000
FM-23 FPGA                      0x10006         0x10000
FM-24 FPGA                      0x10006         0x10000
FM-25 FPGA                      0x10006         0x10000
FM-26 FPGA                      0x10006         0x10000

6) Module 27 upgraded on Fri Mar 27 21:44:36 2026 (775397  us)
EPLD Install Image: EPLD image file 10.5.4.M. built on Fri Dec 12 11:15:18 2025

Status: EPLD Upgrade was Successful

EPLD                            Curr Ver        Old Ver
-------------------------------------------------------
FM-19 FPGA                      0x10006         0x10000
FM-20 FPGA                      0x10006         0x10000
FM-21 FPGA                      0x10006         0x10000
FM-22 FPGA                      0x10006         0x10000
FM-23 FPGA                      0x10006         0x10000
FM-24 FPGA                      0x10006         0x10000
FM-25 FPGA                      0x10006         0x10000
FM-26 FPGA                      0x10006         0x10000

7) Module 27 upgraded on Fri Mar 27 21:38:58 2026 (330582  us)
EPLD Install Image: EPLD image file 10.5.4.M. built on Fri Dec 12 11:15:18 2025

Status: EPLD Upgrade was Successful

EPLD                            Curr Ver        Old Ver
-------------------------------------------------------
FM-19 FPGA                      0x10006         0x10000
FM-20 FPGA                      0x10006         0x10000
FM-21 FPGA                      0x10006         0x10000
FM-22 FPGA                      0x10006         0x10000
FM-23 FPGA                      0x10006         0x10000
FM-24 FPGA                      0x10006         0x10000
FM-25 FPGA                      0x10006         0x10000
FM-26 FPGA                      0x10006         0x10000

8) Module 27 upgraded on Fri Mar 27 21:33:19 2026 (112679  us)
EPLD Install Image: EPLD image file 10.5.4.M. built on Fri Dec 12 11:15:18 2025

Status: EPLD Upgrade was Successful

EPLD                            Curr Ver        Old Ver
-------------------------------------------------------
FM-19 FPGA                      0x10006         0x10000
FM-20 FPGA                      0x10006         0x10000
FM-21 FPGA                      0x10006         0x10000
FM-22 FPGA                      0x10006         0x10000
FM-23 FPGA                      0x10006         0x10000
FM-24 FPGA                      0x10006         0x10000
FM-25 FPGA                      0x10006         0x10000
FM-26 FPGA                      0x10006         0x10000

9) Module 27 upgraded on Fri Mar 27 21:27:41 2026 (957182  us)
EPLD Install Image: EPLD image file 10.5.4.M. built on Fri Dec 12 11:15:18 2025

Status: EPLD Upgrade was Successful

EPLD                            Curr Ver        Old Ver
-------------------------------------------------------
FM-19 FPGA                      0x10006         0x10000
FM-20 FPGA                      0x10006         0x10000
FM-21 FPGA                      0x10006         0x10000
FM-22 FPGA                      0x10006         0x10000
FM-23 FPGA                      0x10006         0x10000
FM-24 FPGA                      0x10006         0x10000
FM-25 FPGA                      0x10006         0x10000
FM-26 FPGA                      0x10006         0x10000

10) Module 27 upgraded on Fri Mar 27 21:22:03 2026 ( 90303  us)
EPLD Install Image: EPLD image file 10.5.4.M. built on Fri Dec 12 11:15:18 2025

Status: EPLD Upgrade was Successful

EPLD                            Curr Ver        Old Ver
-------------------------------------------------------
FM-19 FPGA                      0x10006         0x10000
FM-20 FPGA                      0x10006         0x10000
FM-21 FPGA                      0x10006         0x10000
FM-22 FPGA                      0x10006         0x10000
FM-23 FPGA                      0x10006         0x10000
FM-24 FPGA                      0x10006         0x10000
FM-25 FPGA                      0x10006         0x10000
FM-26 FPGA                      0x10006         0x10000

11) Module 1 upgraded on Fri Mar 27 21:16:24 2026 (240369  us)
EPLD Install Image: EPLD image file 10.5.4.M. built on Fri Dec 12 11:15:18 2025

Status: EPLD Upgrade was Successful

EPLD                            Curr Ver        Old Ver
-------------------------------------------------------
MI FPGA                         0x10014         0x1000b
IO FPGA                         0x10033         0x10006

クラスタ上のクラスタポートの健全性を確認します。

クラスター内のすべてのノードでクラスターポートが稼働しており正常であることを確認します。

network port show -ipspace Cluster

例を表示

cluster1::*> network port show -ipspace Cluster

Node: cluster1-01
                                                                        Ignore
                                                  Speed(Mbps)  Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper   Status   Status
--------- ------------ ---------------- ---- ---- ------------ -------- ------
e0a       Cluster      Cluster          up   9000  auto/100000 healthy  false
e0b       Cluster      Cluster          up   9000  auto/100000 healthy  false

Node: cluster1-02
                                                                        Ignore
                                                  Speed(Mbps)  Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper   Status   Status
--------- ------------ ---------------- ---- ---- ------------ -------- ------
e0a       Cluster      Cluster          up   9000  auto/100000 healthy  false
e0b       Cluster      Cluster          up   9000  auto/100000 healthy  false

Node: cluster1-03
                                                                        Ignore
                                                  Speed(Mbps)  Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper   Status   Status
--------- ------------ ---------------- ---- ---- ------------ -------- ------
e0a       Cluster      Cluster          up   9000  auto/100000 healthy  false
e0b       Cluster      Cluster          up   9000  auto/100000 healthy  false

Node: cluster1-04
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e0a       Cluster      Cluster          up   9000  auto/100000 healthy false
e0b       Cluster      Cluster          up   9000  auto/100000 healthy false

クラスターからスイッチの健全性を確認します。

network device-discovery show -protocol cdp

例を表示

cluster1::*> network device-discovery show -protocol cdp
Node/       Local  Discovered
Protocol    Port   Device (LLDP: ChassisID)  Interface         Platform
----------- ------ ------------------------- ----------------- --------------
cluster1-01/cdp
            e0a    cs1                       Ethernet1/7       N9K-C9336C-FX2
            e0b    cs2                       Ethernet1/7       N9K-C9336C-FX2
cluster01-2/cdp
            e0a    cs1                       Ethernet1/8       N9K-C9336C-FX2
            e0b    cs2                       Ethernet1/8       N9K-C9336C-FX2
cluster01-3/cdp
            e0a    cs1                       Ethernet1/1/1     N9K-C9336C-FX2
            e0b    cs2                       Ethernet1/1/1     N9K-C9336C-FX2
cluster1-04/cdp
            e0a    cs1                       Ethernet1/1/2     N9K-C9336C-FX2
            e0b    cs2                       Ethernet1/1/2     N9K-C9336C-FX2

cluster1::*> system cluster-switch show -is-monitoring-enabled-operational true
Switch                      Type               Address          Model
--------------------------- ------------------ ---------------- --------------
cs1                         cluster-network    10.233.205.90    N9K-C9336C-FX2
     Serial Number: FOCXXXXXXGD
      Is Monitored: true
            Reason: None
  Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                    9.3(5)
    Version Source: CDP

cs2                         cluster-network    10.233.205.91    N9K-C9336C-FX2
     Serial Number: FOCXXXXXXGS
      Is Monitored: true
            Reason: None
  Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                    9.3(5)
    Version Source: CDP

2 entries were displayed.

前の手順でスイッチにロードしたRCFのバージョンによっては、cs1スイッチのコンソールに次の出力が表示されることがあります。

2020 Nov 17 16:07:18 cs1 %$ VDC-1 %$ %STP-2-UNBLOCK_CONSIST_PORT: Unblocking port port-channel1 on VLAN0092. Port consistency restored.
2020 Nov 17 16:07:23 cs1 %$ VDC-1 %$ %STP-2-BLOCK_PVID_PEER: Blocking port-channel1 on VLAN0001. Inconsistent peer vlan.
2020 Nov 17 16:07:23 cs1 %$ VDC-1 %$ %STP-2-BLOCK_PVID_LOCAL: Blocking port-channel1 on VLAN0092. Inconsistent local vlan.

クラスタが正常に動作していることを確認します。

cluster show

例を表示

cluster1::*> cluster show
Node                 Health   Eligibility   Epsilon
-------------------- -------- ------------- -------
cluster1-01          true     true          false
cluster1-02          true     true          false
cluster1-03          true     true          true
cluster1-04          true     true          false
4 entries were displayed.
cluster1::*>

手順 6 ～ 8 を繰り返して、スイッチ cs1 に NX-OS ソフトウェアをインストールします。
クラスタ LIF で自動復帰を有効にする前に、リモートクラスタインターフェイスの接続を確認します。

ONTAP 9.9.1以降

使用することができます `network interface check cluster-connectivity`クラスター接続のアクセシビリティチェックを開始し、詳細を表示するコマンド:

network interface check cluster-connectivity start`そして `network interface check cluster-connectivity show

cluster1::*> network interface check cluster-connectivity start

注意: 実行する前に数秒待ってください `show`詳細を表示するコマンド。

cluster1::*> network interface check cluster-connectivity show
                                  Source               Destination         Packet
Node   Date                       LIF                  LIF                 Loss
------ -------------------------- -------------------- ------------------- -----------
cluster1-01
       3/5/2022 19:21:18 -06:00   cluster1-01_clus2    cluster1-02-clus1   none
       3/5/2022 19:21:20 -06:00   cluster1-01_clus2    cluster1-02_clus2   none
cluster1-02
       3/5/2022 19:21:18 -06:00   cluster1-02_clus2    cluster1-01_clus1   none
       3/5/2022 19:21:20 -06:00   cluster1-02_clus2    cluster1-01_clus2   none

ONTAPのすべてのリリース

すべてのONTAPリリースでは、 `cluster ping-cluster -node <name>`接続を確認するコマンド:

cluster ping-cluster -node <name>

cluster1::*> cluster ping-cluster -node local
Host is cluster1-02
Getting addresses from network interface table...
Cluster cluster1-01_clus1 169.254.209.69 cluster1-01     e0a
Cluster cluster1-01_clus2 169.254.49.125 cluster1-01     e0b
Cluster cluster1-02_clus1 169.254.47.194 cluster1-02     e0a
Cluster cluster1-02_clus2 169.254.19.183 cluster1-02     e0b
Local = 169.254.47.194 169.254.19.183
Remote = 169.254.209.69 169.254.49.125
Cluster Vserver Id = 4294967293
Ping status:

Basic connectivity succeeds on 4 path(s)
Basic connectivity fails on 0 path(s)

Detected 9000 byte MTU on 4 path(s):
    Local 169.254.19.183 to Remote 169.254.209.69
    Local 169.254.19.183 to Remote 169.254.49.125
    Local 169.254.47.194 to Remote 169.254.209.69
    Local 169.254.47.194 to Remote 169.254.49.125
Larger than PMTU communication succeeds on 4 path(s)
RPC status:
2 paths up, 0 paths down (tcp check)
2 paths up, 0 paths down (udp check)

クラスタLIFで自動復帰を有効にします。

network interface modify -vserver Cluster -lif * -auto-revert true

クラスタ LIF がホームポートに戻ったことを確認します。

network interface show -vserver Cluster

例を表示

cluster1::*> network interface show -vserver Cluster
            Logical            Status     Network            Current             Current Is
Vserver     Interface          Admin/Oper Address/Mask       Node                Port    Home
----------- ------------------ ---------- ------------------ ------------------- ------- ----
Cluster
            cluster1-01_clus1  up/up      169.254.3.4/23     cluster1-01         e0b     true
            cluster1-01_clus2  up/up      169.254.3.5/23     cluster1-01         e0b     true
            cluster1-02_clus1  up/up      169.254.3.8/23     cluster1-02         e0b     true
            cluster1-02_clus2  up/up      169.254.3.9/23     cluster1-02         e0b     true
            cluster1-03_clus1  up/up      169.254.1.3/23     cluster1-03         e0b     true
            cluster1-03_clus2  up/up      169.254.1.1/23     cluster1-03         e0b     true
            cluster1-04_clus1  up/up      169.254.1.6/23     cluster1-04         e0b     true
            cluster1-04_clus2  up/up      169.254.1.7/23     cluster1-04         e0b     true
cluster1::*>

クラスタLIFがホームポートに戻っていない場合は、ローカルノードから手動でリバートしてください。

network interface revert -vserver Cluster -lif <lif_name>

次の手順

NX-OSソフトウェアをインストールまたはアップグレードしたら、"参照構成ファイル (RCF) をインストールまたはアップグレードする"。

NX-OSソフトウェアをインストールまたはアップグレードする

Creating your file...

要件の確認

ソフトウェアをインストールする