RCF(Reference Configuration File) 설치
Nexus 92300YC 스위치를 처음 설정한 후 RCF를 설치할 수 있습니다.
이 절차의 예에서는 다음 스위치 및 노드 명명법을 사용합니다.
-
두 Cisco 스위치의 이름은 CS1, CS2입니다.
-
노드 이름은 노드1과 노드2입니다.
-
클러스터 LIF 이름은 node1의 node1_clus1, node2_clus1, node2의 node2_clus2 입니다.
-
'cluster1:: *>' 프롬프트는 클러스터의 이름을 나타냅니다.
-
각 노드의 클러스터 포트 이름은 e0a, e0b 입니다.
를 참조하십시오 "Hardware Universe^" 플랫폼에 지원되는 실제 클러스터 포트의 경우
-
Nexus 92300YC 스위치에 지원되는 ISL(Inter-Switch Link)은 포트 1/65 및 1/66입니다.
-
Nexus 92300YC 스위치에서 지원되는 노드 연결은 포트 1/1 ~ 1/66입니다.
-
이 절차의 예에서는 두 개의 노드를 사용합니다. 이들 노드는 2개의 10GbE 클러스터 인터커넥트 포트를 사용합니다
e0a
및e0b
. 를 참조하십시오 "Hardware Universe" 사용 중인 플랫폼에서 올바른 클러스터 포트를 확인하려면 다음을 수행합니다.
-
현재 RCF가 있어야 합니다.
-
클러스터가 완전하게 작동해야 합니다(로그에 오류가 없거나 이와 유사한 문제가 없어야 함).
-
NX-OS만 설치하고 현재 RCF 버전을 유지하는 경우 원하는 부팅 이미지를 반영하도록 RCF에서 원하는 부팅 구성을 확인하거나 설정해야 합니다.
-
현재 부팅 이미지를 반영하도록 부팅 구성을 변경해야 하는 경우, 나중에 재부팅할 때 올바른 버전이 인스턴스화되도록 RCF를 다시 적용하기 전에 이 구성을 변경해야 합니다.
-
의 스위치 호환성 표를 참조하십시오 "Cisco 이더넷 스위치" 지원되는 ONTAP, NX-OS 및 RCF 버전에 대한 페이지입니다.
-
RCF의 명령 구문과 NX-OS 버전에 있는 명령 구문 간에 명령 의존성이 있을 수 있습니다.
이 절차를 수행하려면 ONTAP 명령과 Cisco Nexus 9000 시리즈 스위치 명령을 모두 사용해야 합니다. 달리 표시되지 않는 한 ONTAP 명령이 사용됩니다.
명령 출력은 ONTAP의 릴리즈별로 다를 수 있습니다.
-
클러스터 스위치를 관리 네트워크에 연결합니다.
-
RCF를 호스팅하는 서버에 대한 연결을 확인하려면 ping 명령을 사용합니다.
이 예에서는 스위치가 IP 주소 172.19.2.1로 서버에 연결할 수 있는지 확인합니다.
cs2# ping 172.19.2.1 Pinging 172.19.2.1 with 0 bytes of data: Reply From 172.19.2.1: icmp_seq = 0. time= 5910 usec.
-
RCF를 Nexus 92300YC 스위치에 복사합니다.
cs2# copy sftp: bootflash: vrf management Enter source filename: /code/Nexus_92300YC_RCF_v1.0.2.txt Enter hostname for the sftp server: 172.19.2.1 Enter username: user1 Outbound-ReKey for 172.19.2.1:22 Inbound-ReKey for 172.19.2.1:22 user1@172.19.2.1's password: sftp> progress Progress meter enabled sftp> get /code/Nexus_92300YC_RCF_v1.0.2.txt /bootflash/nxos.9.2.2.bin /code/Nexus_92300YC_R 100% 9687 530.2KB/s 00:00 sftp> exit Copy complete, now saving to disk (please wait)... Copy complete.
-
RCF를 스위치의 running-config와 병합합니다.
cs2# copy bootflash:Nexus_92300YC_RCF_v1.0.2.txt running-config Disabling ssh: as its enabled right now: generating ecdsa key(521 bits)...... generated ecdsa key Enabling ssh: as it has been disabled this command enables edge port type (portfast) by default on all interfaces. You should now disable edge port type (portfast) explicitly on switched ports leading to hubs, switches and bridges as they may create temporary bridging loops. Edge port type (portfast) should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc... to this interface when edge port type (portfast) is enabled, can cause temporary bridging loops. Use with CAUTION Edge Port Type (Portfast) has been configured on Ethernet1/1 but will only have effect when the interface is in a non-trunking mode. ... Copy complete, now saving to disk (please wait)... Copy complete.
-
스위치에서 RCF가 성공적으로 병합되었는지 확인합니다.
'show running-config'를 선택합니다
cs2# show running-config !Command: show running-config !Running configuration last done at: Wed Apr 10 06:32:27 2019 !Time: Wed Apr 10 06:36:00 2019 version 9.2(2) Bios:version 05.33 switchname cs2 vdc cs2 id 1 limit-resource vlan minimum 16 maximum 4094 limit-resource vrf minimum 2 maximum 4096 limit-resource port-channel minimum 0 maximum 511 limit-resource u4route-mem minimum 248 maximum 248 limit-resource u6route-mem minimum 96 maximum 96 limit-resource m4route-mem minimum 58 maximum 58 limit-resource m6route-mem minimum 8 maximum 8 feature lacp no password strength-check username admin password 5 $5$HY9Kk3F9$YdCZ8iQJ1RtoiEFa0sKP5IO/LNG1k9C4lSJfi5kesl 6 role network-admin ssh key ecdsa 521 banner motd # * * * Nexus 92300YC Reference Configuration File (RCF) v1.0.2 (10-19-2018) * * * * Ports 1/1 - 1/48: 10GbE Intra-Cluster Node Ports * * Ports 1/49 - 1/64: 40/100GbE Intra-Cluster Node Ports * * Ports 1/65 - 1/66: 40/100GbE Intra-Cluster ISL Ports * * *
-
스위치를 재부팅할 때 시작 구성이 되도록 실행 중인 구성을 저장합니다.
cs2# copy running-config startup-config [] 100% Copy complete, now saving to disk (please wait)... Copy complete.
-
ONTAP 9.6P8 이상의 경우, 'system cluster-switch log setup-password', 'system cluster-switch log enable-collection' 명령을 사용하여 스위치 관련 로그 파일을 수집하기 위한 Ethernet 스위치 상태 모니터 로그 수집 기능을 활성화한다
cluster1::*> system cluster-switch log setup-password Enter the switch name: <return> The switch name entered is not recognized. Choose from the following list: cs1 cs2 cluster1::*> system cluster-switch log setup-password Enter the switch name: cs1 RSA key fingerprint is e5:8b:c6:dc:e2:18:18:09:36:63:d9:63:dd:03:d9:cc Do you want to continue? {y|n}::[n] y Enter the password: <enter switch password> Enter the password again: <enter switch password> cluster1::*> system cluster-switch log setup-password Enter the switch name: cs2 RSA key fingerprint is 57:49:86:a1:b9:80:6a:61:9a:86:8e:3c:e3:b7:1f:b1 Do you want to continue? {y|n}:: [n] y Enter the password: <enter switch password> Enter the password again: <enter switch password> cluster1::*> system cluster-switch log enable-collection Do you want to enable cluster log collection for all nodes in the cluster? {y|n}: [n] y Enabling cluster switch log collection. cluster1::*>
-
스위치를 재부팅하고 실행 중인 구성이 올바른지 확인합니다.
다시 로드
cs2# reload This command will reboot the system. (y/n)? [n] y