본 한국어 번역은 사용자 편의를 위해 제공되는 기계 번역입니다. 영어 버전과 한국어 버전이 서로 어긋나는 경우에는 언제나 영어 버전이 우선합니다.
참조 구성 파일(RCF) 업그레이드
기여자
변경 제안
PDF
운영 스위치에 기존 RCF 파일 버전이 설치되어 있는 경우 RCF 버전을 업그레이드합니다.
시작하기 전에
다음 사항이 있는지 확인하세요.
-
스위치 구성의 현재 백업입니다.
-
완벽하게 작동하는 클러스터(로그에 오류나 유사한 문제가 없음).
-
현재의 RCF.
-
RCF 버전을 업데이트하는 경우 원하는 부트 이미지를 반영하는 RCF의 부트 구성이 필요합니다.
현재 부트 이미지를 반영하도록 부트 구성을 변경해야 하는 경우 RCF를 다시 적용하기 전에 변경해야 합니다. 이렇게 하면 향후 재부팅 시 올바른 버전이 인스턴스화됩니다.
|
이 절차 중에는 작동 중인 ISL(스위치 간 링크)이 필요하지 않습니다. 이는 RCF 버전 변경으로 인해 ISL 연결에 일시적으로 영향을 미칠 수 있기 때문에 설계된 기능입니다. 중단 없는 클러스터 운영을 보장하기 위해 다음 절차에서는 대상 스위치에서 단계를 수행하는 동안 모든 클러스터 LIF를 운영 파트너 스위치로 마이그레이션합니다. |
|
새로운 스위치 소프트웨어 버전과 RCF를 설치하기 전에 스위치 설정을 지우고 기본 구성을 수행해야 합니다. 스위치 설정을 지우려면 직렬 콘솔을 사용하여 스위치에 연결해야 하거나 기본 구성 정보를 보존해야 합니다. |
1단계: 업그레이드 준비
-
이 클러스터에서 AutoSupport 활성화된 경우 AutoSupport 메시지를 호출하여 자동 케이스 생성을 억제합니다.
system node autosupport invoke -node * -type all -message MAINT=xh여기서 _x_는 유지 관리 기간(시간)입니다.
-
계속할지 묻는 메시지가 나타나면 *y*를 입력하여 권한 수준을 고급으로 변경합니다.
set -privilege advanced고급 프롬프트(*>)가 나타납니다.
-
스위치에 연결된 각 노드의 포트를 표시합니다.
network device-discovery show예를 보여주세요
cluster1::*> network device-discovery show Node/ Local Discovered Protocol Port Device (LLDP: ChassisID) Interface Platform ----------- ------ ------------------------- ---------------- ---------------- node1-01/cdp e10a cs1(FLMXXXXXXXX) Ethernet1/16/3 N9K-C9332D-GX2B e10b cs2(FDOXXXXXXXX) Ethernet1/16/3 N9K-C9332D-GX2B e11a cs1(FLMXXXXXXXX) Ethernet1/16/4 N9K-C9332D-GX2B e11b cs2(FDOXXXXXXXX) Ethernet1/16/4 N9K-C9332D-GX2B e1a cs1(FLMXXXXXXXX) Ethernet1/16/1 N9K-C9332D-GX2B e1b cs2(FDOXXXXXXXX) Ethernet1/16/1 N9K-C9332D-GX2B . . . e7a cs1(FLMXXXXXXXX) Ethernet1/16/2 N9K-C9332D-GX2B e7b cs2(FDOXXXXXXXX) Ethernet1/16/2 N9K-C9332D-GX2B node1-01/lldp e10a cs1 (c8:60:8f:xx:xx:xx) Ethernet1/16/3 - e10b cs2 (04:e3:87:xx:xx:xx) Ethernet1/16/3 - e11a cs1 (c8:60:8f:xx:xx:xx) Ethernet1/16/4 - e11b cs2 (04:e3:87:xx:xx:xx) Ethernet1/16/4 - e1a cs1 (c8:60:8f:xx:xx:xx) Ethernet1/16/1 - e1b cs2 (04:e3:87:xx:xx:xx) Ethernet1/16/1 - . . . e7a cs1 (c8:60:8f:xx:xx:xx) Ethernet1/16/2 - e7b cs2 (04:e3:87:xx:xx:xx) Ethernet1/16/2 - -
각 항구의 행정 및 운영 상태를 확인하세요.
-
클러스터 포트
-
모든 클러스터 포트가 정상 상태로 작동하는지 확인하세요.
network port show -ipspace Cluster예를 보여주세요
cluster1::*> network port show -ipspace Cluster Node: node1-01 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ----------- -------- ------ e7a Cluster Cluster up 9000 auto/100000 healthy false e7b Cluster Cluster up 9000 auto/100000 healthy false Node: node1-02 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ----------- -------- ------ e7a Cluster Cluster up 9000 auto/100000 healthy false e7b Cluster Cluster up 9000 auto/100000 healthy false Node: node1-03 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ----------- -------- ------ e7a Cluster Cluster up 9000 auto/10000 healthy false e7b Cluster Cluster up 9000 auto/10000 healthy false Node: node1-04 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ----------- -------- ------ e7a Cluster Cluster up 9000 auto/10000 healthy false e7b Cluster Cluster up 9000 auto/10000 healthy false -
모든 클러스터 인터페이스(LIF)가 홈 포트에 있는지 확인하세요.
network interface show -role cluster예를 보여주세요
cluster1::*> network interface show -role cluster Logical Status Network Current Current Is Vserver Interface Admin/Oper Address/Mask Node Port Home ----------- ------------------ ---------- ----------------- ------------ ------- ---- Cluster node1-01_clus1 up/up 169.254.3.4/23 node1-01 e7a true node1-01_clus2 up/up 169.254.3.5/23 node1-01 e7b true node1-02_clus1 up/up 169.254.3.8/23 node1-02 e7a true node1-02_clus2 up/up 169.254.3.9/23 node1-02 e7b true node1-03_clus1 up/up 169.254.1.3/23 node1-03 e7a true node1-03_clus2 up/up 169.254.1.1/23 node1-03 e7b true node1-04_clus1 up/up 169.254.1.6/23 node1-04 e7a true node1-04_clus2 up/up 169.254.1.7/23 node1-04 e7b true 8 entries were displayed. -
클러스터가 두 스위치에 대한 정보를 모두 표시하는지 확인하세요.
system cluster-switch show -is-monitoring-enabled-operational true예를 보여주세요
cluster1::*> system cluster-switch show -is-monitoring-enabled-operational true Switch Type Address Model --------------------------- ------------------ ---------------- --------------- cs2(FDOXXXXXXXX) cluster-network 10.228.137.233 N9K-C9332D-GX2B Serial Number: FDOXXXXXXXX Is Monitored: true Reason: None Software Version: Cisco Nexus Operating System (NX-OS) Software, Version 10.4(2) Version Source: CDP/ISDP cs2(FLMXXXXXXXX) cluster-network 10.228.137.234 N9K-C9332D-GX2B Serial Number: FLMXXXXXXXX Is Monitored: true Reason: None Software Version: Cisco Nexus Operating System (NX-OS) Software, Version 10.4(2) Version Source: CDP/ISDP 2 entries were displayed.
-
-
HA 포트
-
모든 HA 포트가 정상 상태로 작동하는지 확인하세요.
ha interconnect status show -node <node-name>
-
예를 보여주세요
cluster1::*> ha interconnect status show -node node1-01 (system ha interconnect status show) Node: node1-01 Link 0 Status: up Link 1 Status: up Is Link 0 Active: true Is Link 1 Active: true IC RDMA Connection: up Slot: 0 Debug Firmware: no Interconnect Port 0 : Port Name: e1a-17 MTU: 4096 Link Information: ACTIVE Interconnect Port 1 : Port Name: e1b-18 MTU: 4096 Link Information: ACTIVE cluster1::*> ha interconnect status show -node node1-01 (system ha interconnect status show) Node: node1-01 Link 0 Status: up Link 1 Status: up Is Link 0 Active: true Is Link 1 Active: true IC RDMA Connection: up Slot: 0 Debug Firmware: no Interconnect Port 0 : Port Name: e1a-17 MTU: 4096 Link Information: ACTIVE Interconnect Port 1 : Port Name: e1b-18 MTU: 4096 Link Information: ACTIVE . . .-
저장 포트
-
모든 스토리지 포트가 정상 상태로 작동하는지 확인하세요.
storage port show -port-type ENET예를 보여주세요
cluster1::*> storage port show -port-type ENET Speed Node Port Type Mode (Gb/s) State Status ------------------ ---- ----- ------- ------ -------- ----------- node1-01 e10a ENET - 100 enabled online e10b ENET - 100 enabled online e11a ENET - 100 enabled online e11b ENET - 100 enabled online node1-02 e10a ENET - 100 enabled online e10b ENET - 100 enabled online e11a ENET - 100 enabled online e11b ENET - 100 enabled online node1-03 e10a ENET - 100 enabled online e10b ENET - 100 enabled online e11a ENET - 100 enabled online node1-04 e10a ENET - 100 enabled online e10b ENET - 100 enabled online e11a ENET - 100 enabled online e11b ENET - 100 enabled online 16 entries were displayed.
-
-
보관 선반 포트
-
모든 저장 선반 포트가 정상 상태로 작동하는지 확인하세요.
storage shelf port show예를 보여주세요
cluster1::*> storage shelf port show Shelf ID Module State Internal? ----- -- ------ ------------ --------- 1.1 0 A connected false 1 A connected false 2 A connected false 3 A connected false 4 A connected false 5 A connected false 6 A connected false 7 A connected false 8 B connected false 9 B connected false 10 B connected false 11 B connected false 12 B connected false 13 B connected false 14 B connected false 15 B connected false 16 entries were displayed. -
모든 저장 선반 포트가 정상 상태로 작동하는지 확인하세요.
storage shelf port show -fields remote-device,remote-port,connector-state예를 보여주세요
cluster1::*> storage shelf port show -fields remote-device,remote-port,connector-state shelf id connector-state remote-port remote-device ----- -- --------------- -------------- ----------------- 1.1 0 connected Ethernet1/17/1 CX9332D-cs1 1.1 1 connected Ethernet1/15/1 CX9364D-cs1 1.1 2 connected Ethernet1/17/2 CX9332D-cs1 1.1 3 connected Ethernet1/15/2 CX9364D-cs1 1.1 4 connected Ethernet1/17/3 CX9332D-cs1 1.1 5 connected Ethernet1/15/3 CX9364D-cs1 1.1 6 connected Ethernet1/17/4 CX9332D-cs1 1.1 7 connected Ethernet1/15/4 CX9364D-cs1 1.1 8 connected Ethernet1/19/1 CX9332D-cs1 1.1 9 connected Ethernet1/17/1 CX9364D-cs1 1.1 10 connected Ethernet1/19/2 CX9332D-cs1 1.1 11 connected Ethernet1/17/2 CX9364D-cs1 1.1 12 connected Ethernet1/19/3 CX9332D-cs1 1.1 13 connected Ethernet1/17/3 CX9364D-cs1 1.1 14 connected Ethernet1/19/4 CX9332D-cs1 1.1 15 connected Ethernet1/17/4 CX9364D-cs1 16 entries were displayed.
-
-
-
클러스터 LIF에서 자동 되돌리기를 비활성화합니다.
network interface modify -vserver Cluster -lif * -auto-revert false
2단계: 포트 구성
-
스위치 cs1에서 노드의 모든 포트에 연결된 포트를 종료합니다.
cs1# config cs1(config)# interface e1/1/1-4,e1/2/1-4,e1/3/1-4,e1/4/1-4,e1/5/1-4,e1/6/1-4,e1/7/1-4,e1/8/1-4 cs1(config-if-range)# shutdown cs1(config)# interface e1/9/1-4,e1/10/1-4,e1/11/1-4,e1/12/1-4,e1/13/1-4,e1/14/1-4,e1/15/1-4,e1/16/1-4 cs1(config-if-range)# shutdown cs1(config)# interface e1/17/1-4,e1/18/1-4,e1/19/1-4,e1/20/1-4,e1/21/1-4,e1/22/1-44,e1/23/1-4 cs1(config-if-range)# shutdown cs1(config)# interface e1/24/1-,e1/25/1-4,e1/26/1-4,e1/27/1-4,e1/28/1-4,e1/29/1-4,e1/30/1-44 cs1(config-if-range)# shutdown cs1(config-if-range)# exit cs1(config)# exit
네트워크 연결 문제를 방지하려면 모든 연결된 포트를 반드시 종료하세요. 지식 기반 문서를 참조하세요 "스위치 OS 업그레이드 중 클러스터 LIF를 마이그레이션할 때 노드가 쿼럼을 벗어났습니다." 자세한 내용은. -
클러스터 LIF가 스위치 cs1에 호스팅된 포트로 장애 조치되었는지 확인합니다. 몇 초 정도 걸릴 수 있습니다.
network interface show -role cluster예를 보여주세요
cluster1::*> network interface show -role cluster Logical Status Network Current Current Is Vserver Interface Admin/Oper Address/Mask Node Port Home ----------- --------------- ---------- ------------------ ----------- ------- ---- Cluster node1-01_clus1 up/up 169.254.36.44/16 node1-01 e7a true node1-01_clus2 up/up 169.254.7.5/16 node1-01 e7b true node1-02_clus1 up/up 169.254.197.206/16 node1-02 e7a true node1-02_clus2 up/up 169.254.195.186/16 node1-02 e7b true node1-03_clus1 up/up 169.254.192.49/16 node1-03 e7a true node1-03_clus2 up/up 169.254.182.76/16 node1-03 e7b true node1-04_clus1 up/up 169.254.59.49/16 node1-04 e7a true node1-04_clus2 up/up 169.254.62.244/16 node1-04 e7b true 8 entries were displayed. -
클러스터가 정상인지 확인하세요.
cluster show예를 보여주세요
cluster1::*> cluster show Node Health Eligibility Epsilon ----------------- ------- ------------ ------- node1-01 true true false node1-02 true true false node1-03 true true true node1-04 true true false 4 entries were displayed.
-
아직 저장하지 않았다면 다음 명령의 출력을 텍스트 파일에 복사하여 현재 스위치 구성의 사본을 저장하세요.
show running-config-
현재 사이의 사용자 정의 추가 사항을 기록합니다.
running-config그리고 사용 중인 RCF 파일(예: 조직의 SNMP 구성) -
NX-OS 10.2 이상의 경우 다음을 사용하세요.
show diff running-config부트플래시에 저장된 RCF 파일과 비교하는 명령입니다. 그렇지 않은 경우, 제3자 diff/compare 도구를 사용하세요.
-
-
기본 구성 세부 정보를 저장합니다.
write_erase.cfg부트플래시에 있는 파일입니다.
다음 사항을 구성해야 합니다.
-
사용자 이름과 비밀번호
-
관리 IP 주소
-
기본 게이트웨이
-
스위치 이름
cs1# show run | i "username admin password" > bootflash:write_erase.cfgcs1# show run | section "vrf context management" >> bootflash:write_erase.cfgcs1# show run | section "interface mgmt0" >> bootflash:write_erase.cfgcs1# show run | section "switchname" >> bootflash:write_erase.cfgcs1# echo "hardware access-list tcam region ing-racl 1024" >> bootflash:write_erase.cfgcs1# echo "hardware access-list tcam region egr-racl 1024" >> bootflash:write_erase.cfgcs1# echo "hardware access-list tcam region ing-l2-qos 1536" >> bootflash:write_erase.cfg지식 기반 문서를 참조하세요"원격 연결을 유지하면서 Cisco 상호 연결 스위치의 구성을 지우는 방법" 자세한 내용은.
-
-
다음을 확인하십시오.
write_erase.cfg예상대로 파일이 채워졌습니다.show file bootflash:write_erase.cfg -
발행하다
write erase현재 저장된 구성을 지우는 명령:cs1# write eraseWarning: This command will erase the startup-configuration.Do you wish to proceed anyway? (y/n) [n] y -
이전에 저장된 기본 구성을 시작 구성에 복사합니다.
cs1# copy bootflash:write_erase.cfg startup-config -
스위치를 재부팅하세요:
cs1# reloadThis command will reboot the system. (y/n)? [n] y -
관리 IP 주소에 다시 접근할 수 있게 되면 SSH를 통해 스위치에 로그인합니다.
SSH 키와 관련된 호스트 파일 항목을 업데이트해야 할 수도 있습니다.
-
FTP, TFTP, SFTP 또는 SCP 중 하나의 전송 프로토콜을 사용하여 RCF를 스위치 cs1의 부트플래시에 복사합니다.
Cisco 명령에 대한 자세한 내용은 해당 가이드를 참조하세요. "Cisco Nexus 9000 시리즈 NX-OS 명령 참조" 가이드.
예를 보여주세요
이 예에서는 TFTP를 사용하여 RCF를 스위치 cs1의 부트플래시에 복사하는 방법을 보여줍니다.
cs1# copy tftp: bootflash: vrf management Enter source filename: NX9332D-GX2B-RCF-v10.0-Shared.txt Enter hostname for the tftp server: 172.22.201.50 Trying to connect to tftp server......Connection to Server Established. TFTP get operation was successful Copy complete, now saving to disk (please wait)...
-
이전에 다운로드한 RCF를 부트플래시에 적용합니다.
Cisco 명령에 대한 자세한 내용은 해당 가이드를 참조하세요. "Cisco Nexus 9000 시리즈 NX-OS 명령 참조" 가이드.
이 예에서는 RCF 파일을 보여줍니다.
NX9332D-GX2B-RCF-v10.0-Shared.txt스위치 cs1에 설치 중:cs1# copy NX9332D-GX2B-RCF-v10.0-Shared.txt running-config echo-commands
RCF의 설치 참고 사항, 중요 참고 사항 및 배너 섹션을 자세히 읽으세요. 스위치의 올바른 구성과 작동을 보장하려면 이 지침을 읽고 따라야 합니다.
-
RCF 파일이 올바른 최신 버전인지 확인하세요.
show running-config올바른 RCF가 있는지 확인하기 위해 출력을 확인할 때 다음 정보가 올바른지 확인하세요.
-
RCF 배너
-
노드 및 포트 설정
-
사용자 정의
출력은 사이트 구성에 따라 달라집니다. 포트 설정을 확인하고 설치한 RCF에 대한 특정 변경 사항이 있는지 릴리스 노트를 참조하세요.
-
-
스위치 구성에 이전의 사용자 정의를 다시 적용합니다.
-
RCF 버전, 사용자 정의 추가 및 스위치 설정이 올바른지 확인한 후 복사하십시오.
running-config파일을startup-config파일.Cisco 명령에 대한 자세한 내용은 해당 가이드를 참조하세요. "Cisco Nexus 9000 시리즈 NX-OS 명령 참조" 가이드.
cs1# copy running-config startup-config[] 100% Copy complete -
스위치 cs1을 재부팅합니다. 스위치가 재부팅되는 동안 노드에서 보고된 "클러스터 스위치 상태 모니터" 경고 및 "클러스터 포트 다운" 이벤트는 무시할 수 있습니다.
cs1# reloadThis command will reboot the system. (y/n)? [n] y -
클러스터의 모든 포트 상태를 확인합니다.
-
클러스터 포트
-
클러스터의 모든 노드에서 클러스터 포트가 작동 중이고 정상인지 확인하세요.
network port show -ipspace cluster예를 보여주세요
cluster1::*> network port show -ipspace Cluster Node: node1 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ----------- -------- ------ e7a Cluster Cluster up 9000 auto/10000 healthy false e7b Cluster Cluster up 9000 auto/10000 healthy false Node: node1-02 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ----------- -------- ------ e7a Cluster Cluster up 9000 auto/10000 healthy false e7b Cluster Cluster up 9000 auto/10000 healthy false Node: node1-03 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ----------- -------- ------ e7a Cluster Cluster up 9000 auto/100000 healthy false e7b Cluster Cluster up 9000 auto/100000 healthy false Node: node1-04 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ----------- -------- ------ e7a Cluster Cluster up 9000 auto/100000 healthy false e7b Cluster Cluster up 9000 auto/100000 healthy false 8 entries were displayed. -
클러스터에서 스위치 상태를 확인합니다.
network device-discovery show -protocol cdpsystem cluster-switch show -is-monitoring-enabled-operational true예를 보여주세요
cluster1::*> network device-discovery show -protocol cdp Node/ Local Discovered Protocol Port Device (LLDP: ChassisID) Interface Platform ----------- ------ ------------------------- ---------------- ---------------- node1-01/cdp e10a cs1(FLMXXXXXXXX) Ethernet1/16/3 N9K-C9332D-GX2B e10b cs2(FDOXXXXXXXX) Ethernet1/16/3 N9K-C9332D-GX2B e11a cs1(FLMXXXXXXXX) Ethernet1/16/4 N9K-C9332D-GX2B e11b cs2(FDOXXXXXXXX) Ethernet1/16/4 N9K-C9332D-GX2B e1a cs1(FLMXXXXXXXX) Ethernet1/16/1 N9K-C9332D-GX2B e1b cs2(FDOXXXXXXXX) Ethernet1/16/1 N9K-C9332D-GX2B . . . e7a cs1(FLMXXXXXXXX) Ethernet1/16/2 N9K-C9332D-GX2B e7b cs2(FDOXXXXXXXX) Ethernet1/16/2 N9K-C9332D-GX2B cluster1::*> system cluster-switch show -is-monitoring-enabled-operational true Switch Type Address Model --------------------------- ------------------ ---------------- --------------- cs2(FDOXXXXXXXX) cluster-network 10.228.137.233 N9K-C9332D-GX2B Serial Number: FDOXXXXXXXX Is Monitored: true Reason: None Software Version: Cisco Nexus Operating System (NX-OS) Software, Version 10.4(2) Version Source: CDP/ISDP cs1(FLMXXXXXXXX) cluster-network 10.228.137.234 N9K-C9332D-GX2B Serial Number: FLMXXXXXXXX Is Monitored: true Reason: None Software Version: Cisco Nexus Operating System (NX-OS) Software, Version 10.4(2) Version Source: CDP/ISDP 2 entries were displayed.
-
-
HA 포트
-
모든 HA 포트가 정상 상태로 작동하는지 확인하세요.
ha interconnect status show -node <node-name>
-
예를 보여주세요
cluster1::*> ha interconnect status show -node node1-01 (system ha interconnect status show) Node: node1-01 Link 0 Status: up Link 1 Status: up Is Link 0 Active: true Is Link 1 Active: true IC RDMA Connection: up Slot: 0 Debug Firmware: no Interconnect Port 0 : Port Name: e1a-17 MTU: 4096 Link Information: ACTIVE Interconnect Port 1 : Port Name: e1b-18 MTU: 4096 Link Information: ACTIVE cluster1::*> ha interconnect status show -node node1-02 (system ha interconnect status show) Node: node1-02 Link 0 Status: up Link 1 Status: up Is Link 0 Active: true Is Link 1 Active: true IC RDMA Connection: up Slot: 0 Debug Firmware: no Interconnect Port 0 : Port Name: e1a-17 MTU: 4096 Link Information: ACTIVE Interconnect Port 1 : Port Name: e1b-18 MTU: 4096 Link Information: ACTIVE . . .-
저장 포트
-
모든 스토리지 포트가 정상 상태로 작동하는지 확인하세요.
storage port show -port-type ENET예를 보여주세요
cluster1::*> storage port show -port-type ENET Speed Node Port Type Mode (Gb/s) State Status ------------------ ---- ----- ------- ------ -------- ----------- node1-01 e10a ENET - 100 enabled online e10b ENET - 100 enabled online e11a ENET - 100 enabled online e11b ENET - 100 enabled online node1-02 e10a ENET - 100 enabled online e10b ENET - 100 enabled online e11a ENET - 100 enabled online e11b ENET - 100 enabled online node1-03 e10a ENET - 100 enabled online e10b ENET - 100 enabled online e11a ENET - 100 enabled online node1-04 e10a ENET - 100 enabled online e10b ENET - 100 enabled online e11a ENET - 100 enabled online e11b ENET - 100 enabled online 16 entries were displayed.
-
-
보관 선반 포트
-
모든 저장 선반 포트가 정상 상태로 작동하는지 확인하세요.
storage shelf port show예를 보여주세요
cluster1::*> storage shelf port show Shelf ID Module State Internal? ----- -- ------ ------------ --------- 1.1 0 A connected false 1 A connected false 2 A connected false 3 A connected false 4 A connected false 5 A connected false 6 A connected false 7 A connected false 8 B connected false 9 B connected false 10 B connected false 11 B connected false 12 B connected false 13 B connected false 14 B connected false 15 B connected false 16 entries were displayed. -
모든 저장 선반 포트의 연결 상태를 확인하세요.
storage shelf port show -fields remote-device,remote-port,connector-state예를 보여주세요
cluster1::*> storage shelf port show -fields remote-device,remote-port,connector-state shelf id connector-state remote-port remote-device ----- -- --------------- -------------- ----------------- 1.1 0 connected Ethernet1/17/1 CX9332D-cs1 1.1 1 connected Ethernet1/15/1 CX9364D-cs1 1.1 2 connected Ethernet1/17/2 CX9332D-cs1 1.1 3 connected Ethernet1/15/2 CX9364D-cs1 1.1 4 connected Ethernet1/17/3 CX9332D-cs1 1.1 5 connected Ethernet1/15/3 CX9364D-cs1 1.1 6 connected Ethernet1/17/4 CX9332D-cs1 1.1 7 connected Ethernet1/15/4 CX9364D-cs1 1.1 8 connected Ethernet1/19/1 CX9332D-cs1 1.1 9 connected Ethernet1/17/1 CX9364D-cs1 1.1 10 connected Ethernet1/19/2 CX9332D-cs1 1.1 11 connected Ethernet1/17/2 CX9364D-cs1 1.1 12 connected Ethernet1/19/3 CX9332D-cs1 1.1 13 connected Ethernet1/17/3 CX9364D-cs1 1.1 14 connected Ethernet1/19/4 CX9332D-cs1 1.1 15 connected Ethernet1/17/4 CX9364D-cs1 16 entries were displayed.
-
-
-
클러스터가 정상인지 확인하세요.
cluster show예를 보여주세요
cluster1::*> cluster show Node Health Eligibility Epsilon ----------------- -------- ------------- ------- node1-01 true true false node1-02 true true false node1-03 true true true node1-04 true true false 4 entries were displayed.
-
스위치 cs2에서 4~18단계를 반복합니다.
-
클러스터 LIF에서 자동 되돌리기를 활성화합니다.
network interface modify -vserver Cluster -lif * -auto-revert true
3단계: 클러스터 네트워크 구성 및 클러스터 상태 확인
-
클러스터 포트에 연결된 스위치 포트가 *작동*하는지 확인하세요.
show interface brief예를 보여주세요
cs1# show interface brief | grep up . . Eth1/9/3 1 eth trunk up none 100G(D) -- Eth1/9/4 1 eth trunk up none 100G(D) -- Eth1/15/1 1 eth trunk up none 100G(D) -- Eth1/15/2 1 eth trunk up none 100G(D) -- Eth1/15/3 1 eth trunk up none 100G(D) -- Eth1/15/4 1 eth trunk up none 100G(D) -- Eth1/16/1 1 eth trunk up none 100G(D) -- Eth1/16/2 1 eth trunk up none 100G(D) -- Eth1/16/3 1 eth trunk up none 100G(D) -- Eth1/16/4 1 eth trunk up none 100G(D) -- Eth1/17/1 1 eth trunk up none 100G(D) -- Eth1/17/2 1 eth trunk up none 100G(D) -- Eth1/17/3 1 eth trunk up none 100G(D) -- Eth1/17/4 1 eth trunk up none 100G(D) -- . . .
-
예상 노드가 여전히 연결되어 있는지 확인하세요.
show cdp neighbors예를 보여주세요
cs1# show cdp neighbors Capability Codes: R - Router, T - Trans-Bridge, B - Source-Route-Bridge S - Switch, H - Host, I - IGMP, r - Repeater, V - VoIP-Phone, D - Remotely-Managed-Device, s - Supports-STP-Dispute Device-ID Local Intrfce Hldtme Capability Platform Port ID cs2(FDOXXXXXXXX) Eth1/31 179 R S I s N9K-C9364D-GX2A Eth1/63 cs2(FDOXXXXXXXX) Eth1/32 179 R S I s N9K-C9364D-GX2A Eth1/64 node1-01 Eth1/4/1 123 H AFX-1K e1a node1-01 Eth1/4/2 123 H AFX-1K e7a node1-01 Eth1/4/3 123 H AFX-1K e10a node1-01 Eth1/4/4 123 H AFX-1K e11a node1-02 Eth1/9/1 138 H AFX-1K e1a node1-02 Eth1/9/2 138 H AFX-1K e7a node1-02 Eth1/9/3 138 H AFX-1K e10a node1-02 Eth1/9/4 138 H AFX-1K e11a node1-03 Eth1/15/1 138 H AFX-1K e1a node1-03 Eth1/15/2 138 H AFX-1K e7a node1-03 Eth1/15/3 138 H AFX-1K e10a node1-03 Eth1/15/4 138 H AFX-1K e11a node1-04 Eth1/16/1 173 H AFX-1K e1a node1-04 Eth1/16/2 173 H AFX-1K e7a node1-04 Eth1/16/3 173 H AFX-1K e10a node1-04 Eth1/16/4 173 H AFX-1K e11a Total entries displayed: 18 -
다음 명령을 사용하여 클러스터 노드가 올바른 클러스터 VLAN에 있는지 확인하세요.
show vlan briefshow interface trunk예를 보여주세요
cs1# show vlan brief VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Po1, Po999, Eth1/31, Eth1/32 Eth1/33, Eth1/34, Eth1/1/1 Eth1/1/2, Eth1/1/3, Eth1/1/4 Eth1/2/1, Eth1/2/2, Eth1/2/3 Eth1/2/4, Eth1/3/1, Eth1/3/2 Eth1/3/3, Eth1/3/4, Eth1/4/1 Eth1/4/2, Eth1/4/3, Eth1/4/4 Eth1/5/1, Eth1/5/2, Eth1/5/3 Eth1/5/4, Eth1/6/1, Eth1/6/2 Eth1/6/3, Eth1/6/4, Eth1/7/1 Eth1/7/2, Eth1/7/3, Eth1/7/4 Eth1/8/1, Eth1/8/2, Eth1/8/3 Eth1/8/4, Eth1/9/1, Eth1/9/2 Eth1/9/3, Eth1/9/4, Eth1/10/1 Eth1/10/2, Eth1/10/3, Eth1/10/4 Eth1/11/1, Eth1/11/2, Eth1/11/3 Eth1/11/4, Eth1/12/1, Eth1/12/2 Eth1/12/3, Eth1/12/4, Eth1/13/1 Eth1/13/2, Eth1/13/3, Eth1/13/4 Eth1/14/1, Eth1/14/2, Eth1/14/3 Eth1/14/4, Eth1/15/1, Eth1/15/2 Eth1/15/3, Eth1/15/4, Eth1/16/1 Eth1/16/2, Eth1/16/3, Eth1/16/4 Eth1/17/1, Eth1/17/2, Eth1/17/3 Eth1/17/4, Eth1/18/1, Eth1/18/2 Eth1/18/3, Eth1/18/4, Eth1/19/1 Eth1/19/2, Eth1/19/3, Eth1/19/4 Eth1/20/1, Eth1/20/2, Eth1/20/3 Eth1/20/4, Eth1/21/1, Eth1/21/2 Eth1/21/3, Eth1/21/4, Eth1/22/1 Eth1/22/2, Eth1/22/3, Eth1/22/4 Eth1/23/1, Eth1/23/2, Eth1/23/3 Eth1/23/4, Eth1/24/1, Eth1/24/2 Eth1/24/3, Eth1/24/4, Eth1/25/1 Eth1/25/2, Eth1/25/3, Eth1/25/4 Eth1/26/1, Eth1/26/2, Eth1/26/3 Eth1/26/4, Eth1/27/1, Eth1/27/2 Eth1/27/3, Eth1/27/4, Eth1/28/1 Eth1/28/2, Eth1/28/3, Eth1/28/4 Eth1/29/1, Eth1/29/2, Eth1/29/3 Eth1/29/4, Eth1/30/1, Eth1/30/2 Eth1/30/3, Eth1/30/4 17 VLAN0017 active Eth1/1/1, Eth1/1/2, Eth1/1/3 Eth1/1/4, Eth1/2/1, Eth1/2/2 Eth1/2/3, Eth1/2/4, Eth1/3/1 Eth1/3/2, Eth1/3/3, Eth1/3/4 Eth1/4/1, Eth1/4/2, Eth1/4/3 Eth1/4/4, Eth1/5/1, Eth1/5/2 Eth1/5/3, Eth1/5/4, Eth1/6/1 Eth1/6/2, Eth1/6/3, Eth1/6/4 Eth1/7/1, Eth1/7/2, Eth1/7/3 Eth1/7/4, Eth1/8/1, Eth1/8/2 Eth1/8/3, Eth1/8/4, Eth1/9/1 Eth1/9/2, Eth1/9/3, Eth1/9/4 Eth1/10/1, Eth1/10/2, Eth1/10/3 Eth1/10/4, Eth1/11/1, Eth1/11/2 Eth1/11/3, Eth1/11/4, Eth1/12/1 Eth1/12/2, Eth1/12/3, Eth1/12/4 Eth1/13/1, Eth1/13/2, Eth1/13/3 Eth1/13/4, Eth1/14/1, Eth1/14/2 Eth1/14/3, Eth1/14/4, Eth1/15/1 Eth1/15/2, Eth1/15/3, Eth1/15/4 Eth1/16/1, Eth1/16/2, Eth1/16/3 Eth1/16/4, Eth1/17/1, Eth1/17/2 Eth1/17/3, Eth1/17/4, Eth1/18/1 Eth1/18/2, Eth1/18/3, Eth1/18/4 Eth1/19/1, Eth1/19/2, Eth1/19/3 Eth1/19/4, Eth1/20/1, Eth1/20/2 Eth1/20/3, Eth1/20/4, Eth1/21/1 Eth1/21/2, Eth1/21/3, Eth1/21/4 Eth1/22/1, Eth1/22/2, Eth1/22/3 Eth1/22/4, Eth1/23/1, Eth1/23/2 Eth1/23/3, Eth1/23/4, Eth1/24/1 Eth1/24/2, Eth1/24/3, Eth1/24/4 Eth1/25/1, Eth1/25/2, Eth1/25/3 Eth1/25/4, Eth1/26/1, Eth1/26/2 Eth1/26/3, Eth1/26/4, Eth1/27/1 Eth1/27/2, Eth1/27/3, Eth1/27/4 Eth1/28/1, Eth1/28/2, Eth1/28/3 Eth1/28/4, Eth1/29/1, Eth1/29/2 Eth1/29/3, Eth1/29/4, Eth1/30/1 Eth1/30/2, Eth1/30/3, Eth1/30/4 18 VLAN0018 active Eth1/1/1, Eth1/1/2, Eth1/1/3 Eth1/1/4, Eth1/2/1, Eth1/2/2 Eth1/2/3, Eth1/2/4, Eth1/3/1 Eth1/3/2, Eth1/3/3, Eth1/3/4 Eth1/4/1, Eth1/4/2, Eth1/4/3 Eth1/4/4, Eth1/5/1, Eth1/5/2 Eth1/5/3, Eth1/5/4, Eth1/6/1 Eth1/6/2, Eth1/6/3, Eth1/6/4 Eth1/7/1, Eth1/7/2, Eth1/7/3 Eth1/7/4, Eth1/8/1, Eth1/8/2 Eth1/8/3, Eth1/8/4, Eth1/9/1 Eth1/9/2, Eth1/9/3, Eth1/9/4 Eth1/10/1, Eth1/10/2, Eth1/10/3 Eth1/10/4, Eth1/11/1, Eth1/11/2 Eth1/11/3, Eth1/11/4, Eth1/12/1 Eth1/12/2, Eth1/12/3, Eth1/12/4 Eth1/13/1, Eth1/13/2, Eth1/13/3 Eth1/13/4, Eth1/14/1, Eth1/14/2 Eth1/14/3, Eth1/14/4, Eth1/15/1 Eth1/15/2, Eth1/15/3, Eth1/15/4 Eth1/16/1, Eth1/16/2, Eth1/16/3 Eth1/16/4, Eth1/17/1, Eth1/17/2 Eth1/17/3, Eth1/17/4, Eth1/18/1 Eth1/18/2, Eth1/18/3, Eth1/18/4 Eth1/19/1, Eth1/19/2, Eth1/19/3 Eth1/19/4, Eth1/20/1, Eth1/20/2 Eth1/20/3, Eth1/20/4, Eth1/21/1 Eth1/21/2, Eth1/21/3, Eth1/21/4 Eth1/22/1, Eth1/22/2, Eth1/22/3 Eth1/22/4, Eth1/23/1, Eth1/23/2 Eth1/23/3, Eth1/23/4, Eth1/24/1 Eth1/24/2, Eth1/24/3, Eth1/24/4 Eth1/25/1, Eth1/25/2, Eth1/25/3 Eth1/25/4, Eth1/26/1, Eth1/26/2 Eth1/26/3, Eth1/26/4, Eth1/27/1 Eth1/27/2, Eth1/27/3, Eth1/27/4 Eth1/28/1, Eth1/28/2, Eth1/28/3 Eth1/28/4, Eth1/29/1, Eth1/29/2 Eth1/29/3, Eth1/29/4, Eth1/30/1 Eth1/30/2, Eth1/30/3, Eth1/30/4 30 VLAN0030 active Eth1/1/1, Eth1/1/2, Eth1/1/3 Eth1/1/4, Eth1/2/1, Eth1/2/2 Eth1/2/3, Eth1/2/4, Eth1/3/1 Eth1/3/2, Eth1/3/3, Eth1/3/4 Eth1/4/1, Eth1/4/2, Eth1/4/3 Eth1/4/4, Eth1/5/1, Eth1/5/2 Eth1/5/3, Eth1/5/4, Eth1/6/1 Eth1/6/2, Eth1/6/3, Eth1/6/4 Eth1/7/1, Eth1/7/2, Eth1/7/3 Eth1/7/4, Eth1/8/1, Eth1/8/2 Eth1/8/3, Eth1/8/4, Eth1/9/1 Eth1/9/2, Eth1/9/3, Eth1/9/4 Eth1/10/1, Eth1/10/2, Eth1/10/3 Eth1/10/4, Eth1/11/1, Eth1/11/2 Eth1/11/3, Eth1/11/4, Eth1/12/1 Eth1/12/2, Eth1/12/3, Eth1/12/4 Eth1/13/1, Eth1/13/2, Eth1/13/3 Eth1/13/4, Eth1/14/1, Eth1/14/2 Eth1/14/3, Eth1/14/4, Eth1/15/1 Eth1/15/2, Eth1/15/3, Eth1/15/4 Eth1/16/1, Eth1/16/2, Eth1/16/3 Eth1/16/4, Eth1/17/1, Eth1/17/2 Eth1/17/3, Eth1/17/4, Eth1/18/1 Eth1/18/2, Eth1/18/3, Eth1/18/4 Eth1/19/1, Eth1/19/2, Eth1/19/3 Eth1/19/4, Eth1/20/1, Eth1/20/2 Eth1/20/3, Eth1/20/4, Eth1/21/1 Eth1/21/2, Eth1/21/3, Eth1/21/4 Eth1/22/1, Eth1/22/2, Eth1/22/3 Eth1/22/4, Eth1/23/1, Eth1/23/2 Eth1/23/3, Eth1/23/4, Eth1/24/1 Eth1/24/2, Eth1/24/3, Eth1/24/4 Eth1/25/1, Eth1/25/2, Eth1/25/3 Eth1/25/4, Eth1/26/1, Eth1/26/2 Eth1/26/3, Eth1/26/4, Eth1/27/1 Eth1/27/2, Eth1/27/3, Eth1/27/4 Eth1/28/1, Eth1/28/2, Eth1/28/3 Eth1/28/4, Eth1/29/1, Eth1/29/2 Eth1/29/3, Eth1/29/4, Eth1/30/1 Eth1/30/2, Eth1/30/3, Eth1/30/4 40 VLAN0040 active Eth1/1/1, Eth1/1/2, Eth1/1/3 Eth1/1/4, Eth1/2/1, Eth1/2/2 Eth1/2/3, Eth1/2/4, Eth1/3/1 Eth1/3/2, Eth1/3/3, Eth1/3/4 Eth1/4/1, Eth1/4/2, Eth1/4/3 Eth1/4/4, Eth1/5/1, Eth1/5/2 Eth1/5/3, Eth1/5/4, Eth1/6/1 Eth1/6/2, Eth1/6/3, Eth1/6/4 Eth1/7/1, Eth1/7/2, Eth1/7/3 Eth1/7/4, Eth1/8/1, Eth1/8/2 Eth1/8/3, Eth1/8/4, Eth1/9/1 Eth1/9/2, Eth1/9/3, Eth1/9/4 Eth1/10/1, Eth1/10/2, Eth1/10/3 Eth1/10/4, Eth1/11/1, Eth1/11/2 Eth1/11/3, Eth1/11/4, Eth1/12/1 Eth1/12/2, Eth1/12/3, Eth1/12/4 Eth1/13/1, Eth1/13/2, Eth1/13/3 Eth1/13/4, Eth1/14/1, Eth1/14/2 Eth1/14/3, Eth1/14/4, Eth1/15/1 Eth1/15/2, Eth1/15/3, Eth1/15/4 Eth1/16/1, Eth1/16/2, Eth1/16/3 Eth1/16/4, Eth1/17/1, Eth1/17/2 Eth1/17/3, Eth1/17/4, Eth1/18/1 Eth1/18/2, Eth1/18/3, Eth1/18/4 Eth1/19/1, Eth1/19/2, Eth1/19/3 Eth1/19/4, Eth1/20/1, Eth1/20/2 Eth1/20/3, Eth1/20/4, Eth1/21/1 Eth1/21/2, Eth1/21/3, Eth1/21/4 Eth1/22/1, Eth1/22/2, Eth1/22/3 Eth1/22/4, Eth1/23/1, Eth1/23/2 Eth1/23/3, Eth1/23/4, Eth1/24/1 Eth1/24/2, Eth1/24/3, Eth1/24/4 Eth1/25/1, Eth1/25/2, Eth1/25/3 Eth1/25/4, Eth1/26/1, Eth1/26/2 Eth1/26/3, Eth1/26/4, Eth1/27/1 Eth1/27/2, Eth1/27/3, Eth1/27/4 Eth1/28/1, Eth1/28/2, Eth1/28/3 Eth1/28/4, Eth1/29/1, Eth1/29/2 Eth1/29/3, Eth1/29/4, Eth1/30/1 Eth1/30/2, Eth1/30/3, Eth1/30/4 cs1# show interface trunk -------------------------------------------------------------------------------- Port Native Status Port Vlan Channel -------------------------------------------------------------------------------- Eth1/1/1 1 trunking -- Eth1/1/2 1 trunking -- Eth1/1/3 1 trunking -- Eth1/1/4 1 trunking -- Eth1/2/1 1 trunking -- Eth1/2/2 1 trunking -- Eth1/2/3 1 trunking -- Eth1/2/4 1 trunking -- . . . Eth1/30/1 none Eth1/30/2 none Eth1/30/3 none Eth1/30/4 none Eth1/31 none Eth1/32 none Po1 1
특정 포트 및 VLAN 사용에 대한 자세한 내용은 RCF의 배너 및 중요 참고 사항 섹션을 참조하세요. -
cs1과 cs2 사이의 ISL이 작동하는지 확인하세요.
show port-channel summary예를 보여주세요
cs1# show port-channel summary Flags: D - Down P - Up in port-channel (members) I - Individual H - Hot-standby (LACP only) s - Suspended r - Module-removed b - BFD Session Wait S - Switched R - Routed U - Up (port-channel) p - Up in delay-lacp mode (member) M - Not in use. Min-links not met -------------------------------------------------------------------------------- Group Port- Type Protocol Member Ports Channel -------------------------------------------------------------------------------- 1 Po1(SU) Eth LACP Eth1/31(P) Eth1/32(P) 999 Po999(SD) Eth NONE -- cs1# -
클러스터 LIF가 홈 포트로 되돌아갔는지 확인하세요.
network interface show -role cluster예를 보여주세요
cluster1::*> network interface show -role cluster Logical Status Network Current Current Is Vserver Interface Admin/Oper Address/Mask Node Port Home ----------- --------------- ---------- ------------------ ----------- ------- ---- Cluster node1-01_clus1 up/up 169.254.36.44/16 node1-01 e7a true node1-01_clus2 up/up 169.254.7.5/16 node1-01 e7b true node1-02_clus1 up/up 169.254.197.206/16 node1-02 e7a true node1-02_clus2 up/up 169.254.195.186/16 node1-02 e7b true node1-03_clus1 up/up 169.254.192.49/16 node1-03 e7a true node1-03_clus2 up/up 169.254.182.76/16 node1-03 e7b true node1-04_clus1 up/up 169.254.59.49/16 node1-04 e7a true node1-04_clus2 up/up 169.254.62.244/16 node1-04 e7b true 8 entries were displayed.클러스터 LIF가 홈 포트로 돌아오지 않은 경우 로컬 노드에서 수동으로 되돌립니다.
network interface revert -vserver vserver_name -lif <lif-name> -
클러스터가 정상인지 확인하세요.
cluster show예를 보여주세요
cluster1::*> cluster show Node Health Eligibility Epsilon ----------------- ------- ------------- ------- node1-01 true true false node1-02 true true false node1-03 true true true node1-04 true true false 4 entries were displayed.
-
원격 클러스터 인터페이스의 연결성을 확인하세요.
-
당신은 사용할 수 있습니다
network interface check cluster-connectivity show클러스터 연결에 대한 접근성 검사 세부 정보를 표시하는 명령:network interface check cluster-connectivity show예를 보여주세요
cluster1::*> network interface check cluster-connectivity show Source Destination Packet Node Date LIF LIF Loss ------ -------------------------- ---------------- --------------- ----------- node1-01 6/4/2025 03:13:33 -04:00 node1-01_clus2 node1-02_clus1 none 6/4/2025 03:13:34 -04:00 node1-01_clus2 node1-02_clus1 none node1-02 6/4/2025 03:13:33 -04:00 node1-02_clus2 node1-01_clus1 none 6/4/2025 03:13:34 -04:00 node1-02_clus2 node1-01_clus2 none . . . -
또는 다음을 사용할 수 있습니다.
cluster ping-cluster -node <node-name>연결성을 확인하는 명령:cluster ping-cluster -node <node-name>
예를 보여주세요
cluster1::*> cluster ping-cluster -node local Host is node1-04 Getting addresses from network interface table... Cluster node1-01_clus1 169.254.36.44 node1-01 e7a Cluster node1-01_clus2 169.254.7.5 node1-01 e7b Cluster node1-02_clus1 169.254.197.206 node1-02 e7a Cluster node1-02_clus2 169.254.195.186 node1-02 e7b Cluster node1-03_clus1 169.254.192.49 node1-03 e7a Cluster node1-03_clus2 169.254.182.76 node1-03 e7b Cluster node1-04_clus1 169.254.59.49 node1-04 e7a Cluster node1-04_clus2 169.254.62.244 node1-04 e7b Local = 169.254.59.49 169.254.62.244 Remote = 169.254.36.44 169.254.7.5 169.254.197.206 169.254.195.186 169.254.192.49 169.254.182.76 Cluster Vserver Id = 4294967293 Ping status: ............ Basic connectivity succeeds on 12 path(s) Basic connectivity fails on 0 path(s) ................................................ Detected 9000 byte MTU on 12 path(s): Local 169.254.59.49 to Remote 169.254.182.76 Local 169.254.59.49 to Remote 169.254.192.49 Local 169.254.59.49 to Remote 169.254.195.186 Local 169.254.59.49 to Remote 169.254.197.206 Local 169.254.59.49 to Remote 169.254.36.44 Local 169.254.59.49 to Remote 169.254.7.5 Local 169.254.62.244 to Remote 169.254.182.76 Local 169.254.62.244 to Remote 169.254.192.49 Local 169.254.62.244 to Remote 169.254.195.186 Local 169.254.62.244 to Remote 169.254.197.206 Local 169.254.62.244 to Remote 169.254.36.44 Local 169.254.62.244 to Remote 169.254.7.5 Larger than PMTU communication succeeds on 12 path(s) RPC status: 6 paths up, 0 paths down (tcp check) 6 paths up, 0 paths down (udp check) -
다음은 무엇인가요?
RCF를 업그레이드한 후에는"SSH 구성을 확인하세요" .