Skip to main content
본 한국어 번역은 사용자 편의를 위해 제공되는 기계 번역입니다. 영어 버전과 한국어 버전이 서로 어긋나는 경우에는 언제나 영어 버전이 우선합니다.

Cisco Nexus 9364D-GX2A 스위치의 NX-OS 업그레이드

기여자 netapp-lisa netapp-jsnyder netapp-yvonneo
PDF

Cisco Nexus 9364D-GX2A 스위치의 NX-OS를 업그레이드하여 AFX 1K 또는 AFX 2K 시스템의 새로운 하드웨어 또는 새로운 ONTAP 버전을 지원합니다.

참고 NetApp은 ONTAP 소프트웨어 업그레이드를 먼저 완료한 다음 스위치 소프트웨어 업그레이드를 수행할 것을 권장합니다.
시작하기 전에

  • 스위치 구성의 현재 백업이 있는지 확인하십시오.

  • 클러스터가 완전히 정상적으로 작동하는지, 즉 로그에 오류가 없거나 유사한 문제가 없는지 확인하십시오.

이 작업에 관하여

  • 필요한 경우 "Cisco Nexus 9000 시리즈 NX-OS 소프트웨어 업그레이드 및 다운그레이드 가이드"에서 자세한 내용을 참조하십시오.

  • 필요한 경우, 현재 및 목표 릴리스를 기반으로 Cisco Nexus 9000 시리즈 스위치의 서비스 중 소프트웨어 업그레이드(ISSU)에 대한 정보를 제공하는 "Cisco Nexus 9000 및 3000 업그레이드 및 ISSU 매트릭스"를 참조할 수 있습니다.

    해당 페이지에서 *중단 업그레이드*를 선택하고 드롭다운 목록에서 현재 릴리스와 대상 릴리스를 선택합니다.

  • AFX 시스템에서 실행 중인 ONTAP 버전에 따라 스위치에서 지원되는 NX-OS 버전이 결정됩니다.

    • AFX 1K 시스템의 스위치에서 지원되는 ONTAP 버전을 실행하는 경우 NX-OS 10.4.2 이상이 지원됩니다.

    • ONTAP 9.19.1GA 이상 버전을 실행하는 AFX 2K 시스템의 스위치는 NX-OS 10.6 이상 버전을 지원합니다.

      지원되는 NX-OS 버전의 최신 목록은 "NetApp Cisco 이더넷 스위치" 페이지를 참조하십시오.

    참고 지원되지 않는 버전으로 NX-OS 버전을 업그레이드하거나 다운그레이드하지 마십시오.

  • 이 절차에는 ONTAP 명령과 Cisco Nexus 9000 시리즈 스위치 명령이 필요하므로, 각 단계에서는 명령을 입력하는 데 사용하는 CLI를 명시합니다.

  • 이 절차의 예에서는 다음 스위치 및 노드 명명법을 사용합니다.

    • 두 Cisco 스위치의 이름은 cs1과 cs2입니다.

    • 노드 이름은 node1-01, node1-02, node1-03, node1-04입니다.

    • 클러스터 LIF 이름은 다음과 같습니다.

      • node1-01에 대한 node1-01_clus1 및 node1-01_clus2

      • node1-02에 대한 node1-02_clus1 및 node1-02_clus2

      • node1-03에 대한 node1-03_clus1 및 node1-03_clus2

      • node1-04에 대한 node1-04_clus1 및 node1-04_clus2

    • 그만큼 cluster1::*> 프롬프트는 클러스터의 이름을 나타냅니다.

  • 이 절차에 제시된 예시는 RCF 10.0을 실행하는 스위치가 있는 AFX 1K 시스템을 기준으로 합니다. AFX 2K 시스템을 사용하는 경우 입력 및 출력이 다를 수 있습니다.

1단계: NX-OS 업그레이드 준비

NX-OS 업그레이드를 준비하려면 각 스위치에 대한 관리 네트워크 연결이 되어 있는지 확인하고, NX-OS 버전을 다운로드하고, 클러스터의 포트 상태를 확인하고, 클러스터 LIF에서 자동 복원 기능을 비활성화해야 합니다.

단계

  1. 각 스위치를 관리 네트워크에 연결하십시오.

  2. 스위치 CLI를 사용하여 NX-OS를 호스팅하는 서버에 대한 연결을 확인합니다.

    ping <IP address>

    예를 보여주세요

    이 예제에서는 스위치가 IP 주소 172.19.2.1의 서버에 도달할 수 있는지 확인합니다.

    cs1# ping 172.19.2.1
Pinging 172.19.2.1 with 0 bytes of data:

Reply From 172.19.2.1: icmp_seq = 0. time= 5910 usec.

  3. 해당 "Cisco 소프트웨어 다운로드" 페이지에서 스위치에 맞는 NX-OS 버전을 다운로드하십시오.

  4. ONTAP CLI를 사용하여 클러스터 스위치에 연결된 각 노드의 클러스터 포트를 표시합니다.

    network device-discovery show
    예를 보여주세요 
    cluster1::*> network device-discovery show

Node/       Local  Discovered
Protocol    Port   Device (LLDP: ChassisID) Interface         Platform
----------- ------ ------------------------ ----------------  ----------------
node1-01/cdp
            e10a   cs1(FLMXXXXXXXX)         Ethernet1/16/3    N9K-C9364D-GX2A
            e10b   cs2(FDOXXXXXXXX)         Ethernet1/13/3    N9K-C9364D-GX2A
            e11a   cs1(FLMXXXXXXXX)         Ethernet1/16/4    N9K-C9364D-GX2A
            e11b   cs2(FDOXXXXXXXX)         Ethernet1/13/4    N9K-C9364D-GX2A
            e1a    cs1(FLMXXXXXXXX)         Ethernet1/16/1    N9K-C9364D-GX2A
            e1b    cs2(FDOXXXXXXXX)         Ethernet1/13/1    N9K-C9364D-GX2A
            .
            .
            .

            e7a    cs1(FLMXXXXXXXX)         Ethernet1/16/2    N9K-C9364D-GX2A
            e7b    cs2(FDOXXXXXXXX)         Ethernet1/13/2    N9K-C9364D-GX2A

node1-01/lldp
            e10a   cs1 (c8:60:8f:xx:xx:xx)  Ethernet1/16/3    -
            e10b   cs2 (04:e3:87:xx:xx:xx)  Ethernet1/13/3    -
            e11a   cs1 (c8:60:8f:xx:xx:xx)  Ethernet1/16/4    -
            e11b   cs2 (04:e3:87:xx:xx:xx)  Ethernet1/13/4    -
            e1a    cs1 (c8:60:8f:xx:xx:xx)  Ethernet1/16/1    -
            e1b    cs2 (04:e3:87:xx:xx:xx)  Ethernet1/13/1    -
            .
            .
            .
            e7a    cs1 (c8:60:8f:xx:xx:xx)  Ethernet1/16/2    -
            e7b    cs2 (04:e3:87:xx:xx:xx)  Ethernet1/13/2    -
.
.
.

  5. ONTAP CLI를 사용하여 각 포트의 관리 및 운영 상태를 확인합니다.

    1. 클러스터 포트

      1. 모든 클러스터 포트가 정상 상태로 작동하는지 확인하세요.

        network port show -ipspace Cluster
        예를 보여주세요 
        cluster1::*> network port show -ipspace Cluster

Node: node1-01
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/100000 healthy false
e7b       Cluster      Cluster          up   9000  auto/100000 healthy false

Node: node1-02
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/100000 healthy false
e7b       Cluster      Cluster          up   9000  auto/100000 healthy false

Node: node1-03

                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/10000 healthy  false
e7b       Cluster      Cluster          up   9000  auto/10000 healthy  false

Node: node1-04
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/10000 healthy  false
e7b       Cluster      Cluster          up   9000  auto/10000 healthy  false

      2. 모든 클러스터 인터페이스(LIF)가 홈 포트에 있는지 확인하세요.

        network interface show -role cluster
        예를 보여주세요 
        cluster1::*> network interface show -role cluster

            Logical         Status     Network            Current   Current Is
Vserver     Interface       Admin/Oper Address/Mask       Node      Port    Home
----------- --------------- ---------- ------------------ --------- ------- ----
Cluster
            node1-01_clus1  up/up      169.254.36.44/16   node1-01  e7a     true
            node1-01_clus2  up/up      169.254.7.5/16     node1-01  e7b     true
            node1-02_clus1  up/up      169.254.197.206/16 node1-02  e7a     true
            node1-02_clus2  up/up      169.254.195.186/16 node1-02  e7b     true
            node1-03_clus1  up/up      169.254.192.49/16  node1-03  e7a     true
            node1-03_clus2  up/up      169.254.182.76/16  node1-03  e7b     true
            node1-04_clus1  up/up      169.254.59.49/16   node1-04  e7a     true
            node1-04_clus2  up/up      169.254.62.244/16  node1-04  e7b     true

8 entries were displayed.

      3. 클러스터가 두 클러스터 스위치에 대한 정보를 모두 표시하는지 확인합니다.

        system cluster-switch show -is-monitoring-enabled-operational true
        예를 보여주세요 
        cluster1::*> system cluster-switch show -is-monitoring-enabled-operational true

Switch                      Type               Address          Model
--------------------------- ------------------ ---------------- ---------------
cs2(FDOXXXXXXXX)            cluster-network    10.228.137.233   N9K-C9364D-GX2A
     Serial Number: FDOXXXXXXXX
      Is Monitored: true
            Reason: None
  Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                    10.4(2)
    Version Source: CDP/ISDP


cs1(FLMXXXXXXXX)             cluster-network   10.228.137.253   N9K-C9364D-GX2A
     Serial Number: FLMXXXXXXXX
      Is Monitored: true
            Reason: None
  Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                    10.4(2)
    Version Source: CDP/ISDP

2 entries were displayed.

    2. HA 포트

      1. 모든 HA 포트가 정상 상태로 작동하는지 확인하세요.

        ha interconnect status show -node <node-name>
        예를 보여주세요 
        cluster1::*> ha interconnect status show -node node1-01
  (system ha interconnect status show)

                       Node: node1-01
              Link 0 Status: up
              Link 1 Status: up
           Is Link 0 Active: true
           Is Link 1 Active: true
         IC RDMA Connection: up
                       Slot: 0
             Debug Firmware: no


Interconnect Port 0 :
                  Port Name: e1a-17
                        MTU: 4096
           Link Information: ACTIVE


Interconnect Port 1 :
                  Port Name: e1b-18
                        MTU: 4096
           Link Information: ACTIVE

cluster1::*> ha interconnect status show -node node1-02
  (system ha interconnect status show)

                       Node: node1-02
              Link 0 Status: up
              Link 1 Status: up
           Is Link 0 Active: true
           Is Link 1 Active: true
         IC RDMA Connection: up
                       Slot: 0
             Debug Firmware: no


Interconnect Port 0 :
                  Port Name: e1a-17
                        MTU: 4096
           Link Information: ACTIVE


Interconnect Port 1 :
                  Port Name: e1b-18
                        MTU: 4096
           Link Information: ACTIVE
.
.
.

    3. 저장 포트

      1. 모든 스토리지 포트가 정상 상태로 작동하는지 확인하세요.

        storage port show -port-type ENET
        예를 보여주세요 
        cluster1::*> storage port show -port-type ENET

                                      Speed
Node               Port Type  Mode    (Gb/s) State    Status
------------------ ---- ----- ------- ------ -------- -----------
node1-01
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
                   e11b ENET  -          100 enabled  online
node1-02
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
                   e11b ENET  -          100 enabled  online
node1-03
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
node1-04
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
                   e11b ENET  -          100 enabled  online
16 entries were displayed.

    4. 보관 선반 포트

      1. 모든 저장 선반 포트가 정상 상태로 작동하는지 확인하세요.

        storage shelf port show
        예를 보여주세요 
        cluster1::*> storage shelf port show

Shelf ID Module State        Internal?
----- -- ------ ------------ ---------
1.1
       0 A      connected    false
       1 A      connected    false
       2 A      connected    false
       3 A      connected    false
       4 A      connected    false
       5 A      connected    false
       6 A      connected    false
       7 A      connected    false
       8 B      connected    false
       9 B      connected    false
      10 B      connected    false
      11 B      connected    false
      12 B      connected    false
      13 B      connected    false
      14 B      connected    false
      15 B      connected    false

16 entries were displayed.

      2. 모든 저장 선반 포트의 연결 상태를 확인하세요.

        storage shelf port show -fields remote-device,remote-port,connector-state
        예를 보여주세요 
        cluster1::*> storage shelf port show -fields remote-device,remote-port,connector-state

shelf id connector-state remote-port    remote-device
----- -- --------------- -------------- -----------------
1.1   0  connected       Ethernet1/17/1 CX9332D-cs1
1.1   1  connected       Ethernet1/15/1 CX9364D-cs1
1.1   2  connected       Ethernet1/17/2 CX9332D-cs1
1.1   3  connected       Ethernet1/15/2 CX9364D-cs1
1.1   4  connected       Ethernet1/17/3 CX9332D-cs1
1.1   5  connected       Ethernet1/15/3 CX9364D-cs1
1.1   6  connected       Ethernet1/17/4 CX9332D-cs1
1.1   7  connected       Ethernet1/15/4 CX9364D-cs1
1.1   8  connected       Ethernet1/19/1 CX9332D-cs1
1.1   9  connected       Ethernet1/17/1 CX9364D-cs1
1.1   10 connected       Ethernet1/19/2 CX9332D-cs1
1.1   11 connected       Ethernet1/17/2 CX9364D-cs1
1.1   12 connected       Ethernet1/19/3 CX9332D-cs1
1.1   13 connected       Ethernet1/17/3 CX9364D-cs1
1.1   14 connected       Ethernet1/19/4 CX9332D-cs1
1.1   15 connected       Ethernet1/17/4 CX9364D-cs1

16 entries were displayed.

  6. ONTAP CLI를 사용하여 클러스터 LIF에서 자동 복원 기능을 비활성화합니다. 클러스터 LIF는 파트너 클러스터 스위치로 페일오버되고, 대상 스위치에서 이 절차를 수행하는 동안 해당 스위치에 유지됩니다.

    network interface modify -vserver Cluster -lif * -auto-revert false

2단계: NX-OS 및 EPLD 이미지 설치

첫 번째 스위치(cs1)에 NX-OS 및 EPLD 이미지를 설치하고 검증한 다음 클러스터의 모든 포트 상태를 확인하고 두 번째 스위치(cs2)에서 이 단계를 반복합니다.

  1. NX-OS 및 EPLD 이미지를 설치합니다. 설치 단계는 현재 사용 중인 NX-OS 버전과 설치 대상 NX-OS 버전에 따라 다를 수 있습니다.

    본인의 상황에 맞는 탭을 선택하십시오.

    • 10.4(2)F에서 10.6(3)F 이상으로 업그레이드

    • 10.6(3)F에서 이후 버전으로 업그레이드

10.4(2)F에서 10.6(3)F 이상으로 업그레이드

다음 단계에 필요한 명령어를 입력하려면 스위치 CLI를 사용합니다.

  1. NX-OS 및 EPLD 이미지를 첫 번째 스위치에 복사합니다.

    copy <protocol>: bootflash: vrf management

    예 
    cs1# *copy sftp: bootflash: vrf management*
Enter source filename: */code/nxos.10.6.3.F.bin*
Enter hostname for the sftp server: *172.19.2.1*
Enter username: *user1*

Outbound-ReKey for 172.19.2.1:22
Inbound-ReKey for 172.19.2.1:22
user1@172.19.2.1's password:
sftp> *progress*
Progress meter enabled
sftp> *get /code/nxos.10.6.3.F.bin /bootflash/nxos.10.6.3.F.bin*
/code/nxos.10.6.3.F.bin  100% 1261MB   9.3MB/s   02:15
sftp> *exit*
Copy complete, now saving to disk (please wait)...
Copy complete.


cs1# *copy sftp: bootflash: vrf management*
Enter source filename: */code/n9000-epld.10.6.3.F.img*
Enter hostname for the sftp server: *172.19.2.1*
Enter username: *user1*

Outbound-ReKey for 172.19.2.1:22
Inbound-ReKey for 172.19.2.1:22
user1@172.19.2.1's password:
sftp> *progress*
Progress meter enabled
sftp> *get /code/n9000-epld.10.6.3.F.img /bootflash/n9000-epld.10.6.3.F.img*
/code/n9000-epld.10.6.3.F.img  100%  161MB   9.5MB/s   00:16
sftp> *exit*
Copy complete, now saving to disk (please wait)...
Copy complete.

  2. NX-OS의 실행 중인 버전을 확인하십시오.

    show version

    예 
    cs1# *show version*
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (C) 2002-2020, Cisco and/or its affiliates.
All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under their own
licenses, such as open source.  This software is provided "as is," and unless
otherwise stated, there is no warranty, express or implied, including but not
limited to warranties of merchantability and fitness for a particular purpose.
Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or
GNU General Public License (GPL) version 3.0  or the GNU
Lesser General Public License (LGPL) Version 2.1 or
Lesser General Public License (LGPL) Version 2.0.
A copy of each such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://opensource.org/licenses/gpl-3.0.html and
http://www.opensource.org/licenses/lgpl-2.1.php and
http://www.gnu.org/licenses/old-licenses/library.txt.

Software
  BIOS: version 08.38
  NXOS: version 10.6.3(F)
  BIOS compile time:  05/29/2020
  NXOS image file is: bootflash:///nxos.10.6.3.F.bin
  NXOS compile time:  4/28/2020 21:00:00 [04/29/2020 02:28:31]


Hardware
  cisco Nexus9000 C9336C-FX2 Chassis
  Intel(R) Xeon(R) CPU E5-2403 v2 @ 1.80GHz with 8154432 kB of memory.
  Processor Board ID FOC20291J6K

  Device name: cs1
  bootflash:   53298520 kB
Kernel uptime is 0 day(s), 0 hour(s), 3 minute(s), 42 second(s)


Last reset at 157524 usecs after Mon Nov  2 18:32:06 2020
  Reason: Reset Requested by CLI command reload
  System version: 9.3(4)
  Service:

plugin
  Core Plugin, Ethernet Plugin

Active Package(s):

cs1#

  3. NX-OS 및 EPLD 이미지를 설치합니다.

NX-OS 10.6(3)F 이상으로 업그레이드할 때 EPLD 이미지는 자동으로 업데이트되지 않습니다. 업그레이드가 완료되고 스위치가 재부팅된 후에는 동일한 업그레이드 install all 명령을 다시 실행해야 합니다.

  • 두 번째 업그레이드 단계에서는 검증만 수행하고 NX-OS 업그레이드는 건너뛰며 EPLD 이미지만 업데이트합니다.

  • NX-OS 10.6(3)F 이상으로 이미 업그레이드한 경우 두 이미지가 동시에 업데이트됩니다.

+ 이미지 파일을 설치하면 스위치가 재부팅될 때마다 해당 파일이 로드됩니다.

+ install all nxos bootflash:nxos.<version number>.bin

+ .예

Details 
cs1# *install all nxos bootflash:nxos.10.6.3.F.bin*   <---- 1st pass updates NX-OS only

Installer will perform compatibility check first. Please wait.
Installer is forced disruptive

Verifying image bootflash:/nxos.10.6.3.F.bin for boot variable "nxos".
[####################] 100% -- SUCCESS

Verifying image type.
[####################] 100% -- SUCCESS

Preparing "nxos" version info using image bootflash:/nxos.10.6.3.F.bin.
[####################] 100% -- SUCCESS

Preparing "bios" version info using image bootflash:/nxos.10.6.3.F.bin.
[####################] 100% -- SUCCESS

Performing module support checks.
[####################] 100% -- SUCCESS

Notifying services about system upgrade.
[####################] 100% -- SUCCESS


Compatibility check is done:
Module  Bootable  Impact          Install-type  Reason
------  --------  --------------- ------------  ---------
1       yes       Disruptive      Reset         Default upgrade is not hitless


Images will be upgraded according to following table:

Module   Image    Running-Version(pri:alt)                 New-Version          Upg-Required
------- --------- ---------------------------------------- -------------------- ------------ 
1        nxos     10.4(2)(F)                                10.6(3)(F)            yes
1        bios     v05.47(04/28/2022):v05.47(04/28/2022)    v05.53(01/22/2025)     yes

Switch will be reloaded for disruptive upgrade.

Do you want to continue with the installation (y/n)? [n] *y*

Install is in progress, please wait.

Performing runtime checks.
[####################] 100% -- SUCCESS

Setting boot variables.
[####################] 100% -- SUCCESS

Performing configuration copy.
[####################] 100% -- SUCCESS

Module 1: Refreshing compact flash and upgrading bios/loader/bootrom.
Warning: please do not remove or power off the module at this time.
[####################] 100% -- SUCCESS
[####################] 100% -- SUCCESS

Finishing the upgrade, switch will reboot in 10 seconds.

. Using the switch CLI, verify the new version of NX-OS after the switch reboots:
+
`show version`
+

.Example
[%collapsible]
cs1# *show version*
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (C) 2002-2020, Cisco and/or its affiliates.
All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under their own
licenses, such as open source.  This software is provided "as is," and unless
otherwise stated, there is no warranty, express or implied, including but not
limited to warranties of merchantability and fitness for a particular purpose.
Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or
GNU General Public License (GPL) version 3.0  or the GNU
Lesser General Public License (LGPL) Version 2.1 or
Lesser General Public License (LGPL) Version 2.0.
A copy of each such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://opensource.org/licenses/gpl-3.0.html and
http://www.opensource.org/licenses/lgpl-2.1.php and
http://www.gnu.org/licenses/old-licenses/library.txt.

Software
  BIOS: version 05.33
  NXOS: version 10.6.3(f)
  BIOS compile time:  09/08/2018
  NXOS image file is: bootflash:///nxos.10.6.3.F.bin
  NXOS compile time:  11/4/2018 21:00:00 [11/05/2018 06:11:06]


Hardware
  cisco Nexus9000 C9332C-GX2B Chassis
  Intel(R) Xeon(R) CPU E5-2403 v2 @ 1.80GHz with 8154432 kB of memory.
  Processor Board ID FOC20291J6K

  Device name: cs1
  bootflash:   53298520 kB
Kernel uptime is 0 day(s), 0 hour(s), 3 minute(s), 42 second(s)

Last reset at 277524 usecs after Mon Nov  2 22:45:12 2020
  Reason: Reset due to upgrade
  System version: 9.3(4)
  Service:

plugin
  Core Plugin, Ethernet Plugin

Active Package(s):

  1. 스위치를 재부팅한 후 다시 로그인하여 새로운 버전의 EPLD가 성공적으로 로드되었는지 확인하세요.

    show version module 1 epld

cs2# *show version module 1 epld*

EPLD Device                     Version
---------------------------------------
MI   FPGA                        0x7
IO   FPGA                        0x19
MI   FPGA2                       0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2

다음 단계에 필요한 명령어를 입력하려면 스위치 CLI를 사용합니다.

  1. NX-OS 및 EPLD 이미지를 첫 번째 스위치에 복사합니다.

    copy <protocol>: bootflash: vrf management

    예

    이 예제는 sftp와 NX-OS 버전 10.6(4)M을 사용합니다.

    cs1# *copy sftp: bootflash: vrf management*
Enter source filename: */code/nxos64-cs.10.6.4.M.bin*
Enter hostname for the sftp server: *172.19.2.1*
Enter username: *user1*

Outbound-ReKey for 172.19.2.1:22
Inbound-ReKey for 172.19.2.1:22
user1@172.19.2.1's password:
sftp> *progress*
Progress meter enabled
sftp> *get /code/nxos64-cs.10.6.4.M.bin /bootflash/nxos64-cs.10.6.4.M.bin*
/code/nxos64-cs.10.6.4.M.bin  100% 1261MB   9.3MB/s   02:15
sftp> *exit*
Copy complete, now saving to disk (please wait)...
Copy complete.

  2. NX-OS의 실행 중인 버전을 확인하십시오.

    show version

    예 
    cs1# *show version*
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (C) 2002-2025, Cisco and/or its affiliates.
All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under their own
licenses, such as open source.  This software is provided "as is," and unless
otherwise stated, there is no warranty, express or implied, including but not
limited to warranties of merchantability and fitness for a particular purpose.
Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or
GNU General Public License (GPL) version 3.0  or the GNU
Lesser General Public License (LGPL) Version 2.1 or
Lesser General Public License (LGPL) Version 2.0.
A copy of each such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://opensource.org/licenses/gpl-3.0.html and
http://www.opensource.org/licenses/lgpl-2.1.php and
http://www.gnu.org/licenses/old-licenses/library.txt.


Software
  BIOS: version 01.14
  NXOS: version 10.6.4.M [Feature Release]
  Host NXOS: version 10.6.4.M
  BIOS compile time:  11/25/2026
  NXOS image file is: bootflash:///nxos.10.6.4.M.bin
  NXOS compile time:  02/27/2026 12:00:00 [03/14/2026 05:25:50]
  NXOS boot mode: LXC


Hardware
  cisco  Nexus9000 C9364D-GX2A Chassis
  Intel(R) Xeon(R) CPU D-1633N @ 2.50GHz with 32802156 kB of memory.
  Processor Board ID FLMXXXXXXXX
  Device name: cs1
  bootflash:  115802886 kB


Kernel uptime is 5 day(s), 2 hour(s), 13 minute(s), 21 second(s)


Last reset at 3580 usecs after Thu Mar 5 15:55:08 2026
  Reason: Reset Requested by CLI command reload
  System version: 10.5.3(f)
  Service:


plugin
  Core Plugin, Ethernet Plugin


Active Package(s):

cs1#

  3. NX-OS 및 EPLD 이미지를 설치합니다.

    이미지 파일을 설치하면 스위치를 재부팅할 때마다 이미지 파일이 로드됩니다.

    install all nxos bootflash:nxos.<version number>.bin

    예

    이 예제는 NX-OS 버전 10.6(4)M을 사용합니다.

    cs1# *install all nxos bootflash:/nxos64-cs.10.6.4.M.bin*

Installer will perform compatibility check first. Please wait.
Installer is forced disruptive

Verifying image bootflash:/nxos64-cs.10.6.4.M.bin for boot variable "nxos".
[####################] 100% -- SUCCESS

Verifying image type.
[####################] 100% -- SUCCESS

Preparing "nxos" version info using image bootflash:/nxos64-cs.10.6.4.M.bin.
[####################] 100% -- SUCCESS

Preparing "bios" version info using image bootflash:/nxos64-cs.10.6.4.M.bin.
[####################] 100% -- SUCCESS

Performing module support checks.
[####################] 100% -- SUCCESS

Notifying services about system upgrade.
[####################] 100% -- SUCCESS


Compatibility check is done:
Module  Bootable  Impact          Install-type  Reason
------  --------  --------------- ------------  ---------
  1     yes       Disruptive      Reset         Default upgrade is not hitless


Images will be upgraded according to following table:

Module   Image    Running-Version(pri:alt)            New-Version         Upg-Required
------- --------- ----------------------------------- ------------------- ------------
  1      nxos     10.4(2)(F)                          10.6(4)(M)          Yes
  1      bios     <current_version>                   <new_version>       No


Switch will be reloaded for disruptive upgrade.

Do you want to continue with the installation (y/n)? [n] *y*

Install is in progress, please wait.

Performing runtime checks.
[####################] 100% -- SUCCESS

Setting boot variables.
[####################] 100% -- SUCCESS

Performing configuration copy.
[####################] 100% -- SUCCESS

Module 1: Refreshing compact flash and upgrading bios/loader/bootrom.
Warning: please do not remove or power off the module at this time.
[####################] 100% -- SUCCESS

Finishing the upgrade, switch will reboot in 10 seconds.

  4. 스위치가 재부팅된 후 NX-OS의 새 버전을 확인하십시오.

    show version

    예 
    cs1# *show version*
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (C) 2002-2025, Cisco and/or its affiliates.
All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under their own
licenses, such as open source.  This software is provided "as is," and unless
otherwise stated, there is no warranty, express or implied, including but not
limited to warranties of merchantability and fitness for a particular purpose.
Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or
GNU General Public License (GPL) version 3.0  or the GNU
Lesser General Public License (LGPL) Version 2.1 or
Lesser General Public License (LGPL) Version 2.0.
A copy of each such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://opensource.org/licenses/gpl-3.0.html and
http://www.opensource.org/licenses/lgpl-2.1.php and
http://www.gnu.org/licenses/old-licenses/library.txt.


Software
  BIOS: version 01.14
  NXOS: version 10.6(4)(M) [Feature Release]
  Host NXOS: version 10.6(4)(M)
  BIOS compile time:  11/25/2024
  NXOS image file is: bootflash:///nxos64-cs.10.6.4.M.bin
  NXOS compile time:  05/30/2026 12:00:00 [06/14/2026 05:25:50]
  NXOS boot mode: LXC


Hardware
  cisco Nexus9000 C9364D-GX2A Chassis
  Intel(R) Xeon(R) CPU D-1633N @ 2.50GHz with 32802156 kB of memory.
  Processor Board ID FLMXXXXXXXX
  Device name: cs2
  bootflash:  115802886 kB


Kernel uptime is 5 day(s), 2 hour(s), 13 minute(s), 21 second(s)


Last reset at 3580 usecs after Thu Jun 5 15:55:08 2026
  Reason: Reset Requested by CLI command reload
  System version: 10.5(4)(M)
  Service:


plugin
  Core Plugin, Ethernet Plugin


Active Package(s):

  5. 새 버전의 EPLD가 성공적으로 로드되었는지 확인하십시오.

    예를 보여주세요

    이 예제는 EPLD 버전 10.6(4)M을 사용합니다.

    cs1# *show install epld status*

1) Module 2 upgraded on Mon May  4 09:17:08 2026 (631239  us)
EPLD Install Image: EPLD image file 10.6.4.M. built on Fri Apr 24 19:49:50 2026

Status: EPLD Upgrade was Successful

EPLD                             Curr Ver       Old Ver
-------------------------------------------------------
MI FPGA                         0x10014         0x1000b
IO FPGA                         0x10033         0x10006

2) Module 27 upgraded on Wed Apr  1 15:03:13 2026 (193093  us)
EPLD Install Image: EPLD image file 10.5.4.M. built on Mon Mar 16 03:28:47 2026

Status: EPLD Upgrade was Successful

EPLD                            Curr Ver        Old Ver
-------------------------------------------------------
IO FPGA                         0x1002d         0x10020

3) Module 28 upgraded on Wed Apr  1 14:59:53 2026 (843907  us)
EPLD Install Image: EPLD image file 10.6.4.M. built on Mon Mar 16 03:28:47 2026

Status: EPLD Upgrade was Successful

EPLD                            Curr Ver        Old Ver
-------------------------------------------------------
IO FPGA                         0x1002d         0x10020

4) Module 27 upgraded on Fri Mar 27 21:55:55 2026 (132290  us)
EPLD Install Image: EPLD image file 10.6.4.M. built on Fri Dec 12 11:15:18 2026

Status: EPLD Upgrade was Successful

EPLD                            Curr Ver        Old Ver
-------------------------------------------------------
FM-19 FPGA                      0x10006         0x10000
FM-20 FPGA                      0x10006         0x10000
FM-21 FPGA                      0x10006         0x10000
FM-22 FPGA                      0x10006         0x10000
FM-23 FPGA                      0x10006         0x10000
FM-24 FPGA                      0x10006         0x10000
FM-25 FPGA                      0x10006         0x10000
FM-26 FPGA                      0x10006         0x10000

5) Module 27 upgraded on Fri Mar 27 21:50:16 2026 (  4899  us)
EPLD Install Image: EPLD image file 10.6.4.M. built on Fri Dec 12 11:15:18 2026

Status: EPLD Upgrade was Successful

EPLD                            Curr Ver        Old Ver
-------------------------------------------------------
FM-19 FPGA                      0x10006         0x10000
FM-20 FPGA                      0x10006         0x10000
FM-21 FPGA                      0x10006         0x10000
FM-22 FPGA                      0x10006         0x10000
FM-23 FPGA                      0x10006         0x10000
FM-24 FPGA                      0x10006         0x10000
FM-25 FPGA                      0x10006         0x10000
FM-26 FPGA                      0x10006         0x10000

6) Module 27 upgraded on Fri Mar 27 21:44:36 2026 (775397  us)
EPLD Install Image: EPLD image file 10.6.4.M. built on Fri Dec 12 11:15:18 2026

Status: EPLD Upgrade was Successful

EPLD                            Curr Ver        Old Ver
-------------------------------------------------------
FM-19 FPGA                      0x10006         0x10000
FM-20 FPGA                      0x10006         0x10000
FM-21 FPGA                      0x10006         0x10000
FM-22 FPGA                      0x10006         0x10000
FM-23 FPGA                      0x10006         0x10000
FM-24 FPGA                      0x10006         0x10000
FM-25 FPGA                      0x10006         0x10000
FM-26 FPGA                      0x10006         0x10000

7) Module 27 upgraded on Fri Mar 27 21:38:58 2026 (330582  us)
EPLD Install Image: EPLD image file 10.6.4.M. built on Fri Dec 12 11:15:18 2026

Status: EPLD Upgrade was Successful

EPLD                            Curr Ver        Old Ver
-------------------------------------------------------
FM-19 FPGA                      0x10006         0x10000
FM-20 FPGA                      0x10006         0x10000
FM-21 FPGA                      0x10006         0x10000
FM-22 FPGA                      0x10006         0x10000
FM-23 FPGA                      0x10006         0x10000
FM-24 FPGA                      0x10006         0x10000
FM-25 FPGA                      0x10006         0x10000
FM-26 FPGA                      0x10006         0x10000

8) Module 27 upgraded on Fri Mar 27 21:33:19 2026 (112679  us)
EPLD Install Image: EPLD image file 10.6.4.M. built on Fri Dec 12 11:15:18 2025

Status: EPLD Upgrade was Successful

EPLD                            Curr Ver        Old Ver
-------------------------------------------------------
FM-19 FPGA                      0x10006         0x10000
FM-20 FPGA                      0x10006         0x10000
FM-21 FPGA                      0x10006         0x10000
FM-22 FPGA                      0x10006         0x10000
FM-23 FPGA                      0x10006         0x10000
FM-24 FPGA                      0x10006         0x10000
FM-25 FPGA                      0x10006         0x10000
FM-26 FPGA                      0x10006         0x10000

9) Module 27 upgraded on Fri Mar 27 21:27:41 2026 (957182  us)
EPLD Install Image: EPLD image file 10.6.4.M. built on Fri Dec 12 11:15:18 2025

Status: EPLD Upgrade was Successful

EPLD                            Curr Ver        Old Ver
-------------------------------------------------------
FM-19 FPGA                      0x10006         0x10000
FM-20 FPGA                      0x10006         0x10000
FM-21 FPGA                      0x10006         0x10000
FM-22 FPGA                      0x10006         0x10000
FM-23 FPGA                      0x10006         0x10000
FM-24 FPGA                      0x10006         0x10000
FM-25 FPGA                      0x10006         0x10000
FM-26 FPGA                      0x10006         0x10000

10) Module 27 upgraded on Fri Mar 27 21:22:03 2026 ( 90303  us)
EPLD Install Image: EPLD image file 10.6.4.M. built on Fri Dec 12 11:15:18 2025

Status: EPLD Upgrade was Successful

EPLD                            Curr Ver        Old Ver
-------------------------------------------------------
FM-19 FPGA                      0x10006         0x10000
FM-20 FPGA                      0x10006         0x10000
FM-21 FPGA                      0x10006         0x10000
FM-22 FPGA                      0x10006         0x10000
FM-23 FPGA                      0x10006         0x10000
FM-24 FPGA                      0x10006         0x10000
FM-25 FPGA                      0x10006         0x10000
FM-26 FPGA                      0x10006         0x10000

11) Module 1 upgraded on Fri Mar 27 21:16:24 2026 (240369  us)
EPLD Install Image: EPLD image file 10.6.4.M. built on Fri Dec 12 11:15:18 2025

Status: EPLD Upgrade was Successful

EPLD                            Curr Ver        Old Ver
-------------------------------------------------------
MI FPGA                         0x10014         0x1000b
IO FPGA                         0x10033         0x10006

  1. ONTAP CLI를 사용하여 클러스터의 모든 포트 상태를 확인합니다.

    1. 클러스터 포트

      1. 클러스터의 모든 노드에서 클러스터 포트가 작동 중이고 정상인지 확인하세요.

        network port show -ipspace Cluster
        예를 보여주세요 
        cluster1::*> network port show -ipspace Cluster

Node: node1-01
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/10000 healthy  false
e7b       Cluster      Cluster          up   9000  auto/10000 healthy  false

Node: node1-02
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/10000 healthy  false
e7b       Cluster      Cluster          up   9000  auto/10000 healthy  false

Node: node1-03
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/100000 healthy false
e7b       Cluster      Cluster          up   9000  auto/100000 healthy false

Node: node1-04
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/100000 healthy false
e7b       Cluster      Cluster          up   9000  auto/100000 healthy false

      2. 클러스터에서 스위치 상태를 확인하세요.

        network device-discovery show -protocol cdp
        system cluster-switch show -is-monitoring-enabled-operational true
        예를 보여주세요 
        cluster1::*> network device-discovery show -protocol cdp

node1-02/cdp
            e10a   cs1(FLMXXXXXXXX)         Ethernet1/16/3    N9K-C9364D-GX2A
            e10b   cs2(FDOXXXXXXXX)         Ethernet1/16/3    N9K-C9364D-GX2A
            e11a   cs1(FLMXXXXXXXX)         Ethernet1/16/4    N9K-C9364D-GX2A
            e11b   cs2(FDOXXXXXXXX)         Ethernet1/16/4    N9K-C9364D-GX2A
            e1a    cs1(FLMXXXXXXXX)         Ethernet1/16/1    N9K-C9364D-GX2A
            e1b    cs2(FDOXXXXXXXX)         Ethernet1/16/1    N9K-C9364D-GX2A
            .
            .
            .
            e7a    cs1(FLM284504N6)         Ethernet1/16/2    N9K-C9364D-GX2A
            e7b    cs2(FDO2846056X)         Ethernet1/16/2    N9K-C9364D-GX2A

node1-01/cdp
            e10a   cs1(FLMXXXXXXXX)         Ethernet1/16/3    N9K-C9364D-GX2A
            e10b   cs2(FDOXXXXXXXX)         Ethernet1/16/3    N9K-C9364D-GX2A
            e11a   cs1(FLMXXXXXXXX)         Ethernet1/16/4    N9K-C9364D-GX2A
            e11b   cs2(FDOXXXXXXXX)         Ethernet1/16/4    N9K-C9364D-GX2A
            e1a    cs1(FLMXXXXXXXX)         Ethernet1/16/1    N9K-C9364D-GX2A
            e1b    cs2(FDOXXXXXXXX)         Ethernet1/16/1    N9K-C9364D-GX2A
           .
           .
           .
            e7a    cs1(FLMXXXXXXXX)         Ethernet1/16/2    N9K-C9364D-GX2A
            e7b    cs2(FDOXXXXXXXX)         Ethernet1/16/2    N9K-C9364D-GX2A
.
.
.

cluster1::*> system cluster-switch show -is-monitoring-enabled-operational true
Switch                      Type               Address          Model
--------------------------- ------------------ ---------------- ---------------
cs2(FDOXXXXXXXX)            cluster-network    10.228.137.233   N9K-C9364D-GX2A
     Serial Number: FDOXXXXXXXX
      Is Monitored: true
            Reason: None
  Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                    10.4(2)
    Version Source: CDP/ISDP


cs1(FLMXXXXXXXX)             cluster-network   10.228.137.253   N9K-C9364D-GX2A
     Serial Number: FLMXXXXXXXX
      Is Monitored: true
            Reason: None
  Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                    10.4(2)
    Version Source: CDP/ISDP

    2. HA 포트

      1. 모든 HA 포트가 정상 상태로 작동하는지 확인하세요.

        ha interconnect status show -node <node-name>
        예를 보여주세요 
        cluster1::*> ha interconnect status show -node node1-01
  (system ha interconnect status show)

                       Node: node1-01
              Link 0 Status: up
              Link 1 Status: up
           Is Link 0 Active: true
           Is Link 1 Active: true
         IC RDMA Connection: up
                       Slot: 0
             Debug Firmware: no


Interconnect Port 0 :
                  Port Name: e1a-17
                        MTU: 4096
           Link Information: ACTIVE


Interconnect Port 1 :
                  Port Name: e1b-18
                        MTU: 4096
           Link Information: ACTIVE

cluster1::*> ha interconnect status show -node node1-02
  (system ha interconnect status show)

                       Node: node1-02
              Link 0 Status: up
              Link 1 Status: up
           Is Link 0 Active: true
           Is Link 1 Active: true
         IC RDMA Connection: up
                       Slot: 0
             Debug Firmware: no


Interconnect Port 0 :
                  Port Name: e1a-17
                        MTU: 4096
           Link Information: ACTIVE


Interconnect Port 1 :
                  Port Name: e1b-18
                        MTU: 4096
           Link Information: ACTIVE
.
.
.

    3. 저장 포트

      1. 모든 스토리지 포트가 정상 상태로 작동하는지 확인하세요.

        storage port show -port-type ENET
        예를 보여주세요 
        cluster1::*> storage port show -port-type ENET


                                      Speed
Node               Port Type  Mode    (Gb/s) State    Status
------------------ ---- ----- ------- ------ -------- -----------
node1-01
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
                   e11b ENET  -          100 enabled  online
node1-02
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
                   e11b ENET  -          100 enabled  online
node1-03
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
node1-04
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
                   e11b ENET  -          100 enabled  online
16 entries were displayed.

    4. 보관 선반 포트

      1. 모든 저장 선반 포트가 정상 상태로 작동하는지 확인하세요.

        storage shelf port show
        예를 보여주세요 
        cluster1::*> storage shelf port show

Shelf ID Module State        Internal?
----- -- ------ ------------ ---------
1.1
       0 A      connected    false
       1 A      connected    false
       2 A      connected    false
       3 A      connected    false
       4 A      connected    false
       5 A      connected    false
       6 A      connected    false
       7 A      connected    false
       8 B      connected    false
       9 B      connected    false
      10 B      connected    false
      11 B      connected    false
      12 B      connected    false
      13 B      connected    false
      14 B      connected    false
      15 B      connected    false

16 entries were displayed.

      2. 모든 저장 선반 포트의 연결 상태를 확인하세요.

        storage shelf port show -fields remote-device,remote-port,connector-state
        예를 보여주세요 
        cluster1::*> storage shelf port show -fields remote-device,remote-port,connector-state

shelf id connector-state remote-port    remote-device
----- -- --------------- -------------- -----------------
1.1   0  connected       Ethernet1/17/1 CX9332D-cs1
1.1   1  connected       Ethernet1/15/1 CX9364D-cs1
1.1   2  connected       Ethernet1/17/2 CX9332D-cs1
1.1   3  connected       Ethernet1/15/2 CX9364D-cs1
1.1   4  connected       Ethernet1/17/3 CX9332D-cs1
1.1   5  connected       Ethernet1/15/3 CX9364D-cs1
1.1   6  connected       Ethernet1/17/4 CX9332D-cs1
1.1   7  connected       Ethernet1/15/4 CX9364D-cs1
1.1   8  connected       Ethernet1/19/1 CX9332D-cs1
1.1   9  connected       Ethernet1/17/1 CX9364D-cs1
1.1   10 connected       Ethernet1/19/2 CX9332D-cs1
1.1   11 connected       Ethernet1/17/2 CX9364D-cs1
1.1   12 connected       Ethernet1/19/3 CX9332D-cs1
1.1   13 connected       Ethernet1/17/3 CX9364D-cs1
1.1   14 connected       Ethernet1/19/4 CX9332D-cs1
1.1   15 connected       Ethernet1/17/4 CX9364D-cs1

16 entries were displayed.

  2. ONTAP CLI를 사용하여 클러스터가 정상인지 확인합니다.

    cluster show
    예를 보여주세요 
    cluster1::*> cluster show


Node                 Health  Eligibility   Epsilon
-------------------- ------- ------------  ------------
node1-01             true    true          false
node1-02             true    true          false
node1-03             true    true          false
node1-04             true    true          true

4 entries were displayed.

  3. 스위치 cs2에 NX-OS 및 EPLD 이미지를 설치하려면 다음 단계를 반복하십시오.

3단계: NX-OS 업그레이드 완료

ONTAP CLI를 사용하여 클러스터 LIF에서 자동 복원 기능을 다시 활성화하고 클러스터 LIF가 홈 포트로 복원되었는지 확인하여 NX-OS 업그레이드를 완료합니다.

  1. 클러스터 LIF에서 자동 복원 기능을 다시 활성화합니다.

    network interface modify -vserver Cluster -lif * -auto-revert true

  2. 클러스터 LIF가 홈 포트로 되돌아갔는지 확인하세요.

    network interface show -role cluster
    예를 보여주세요 
    cluster1::*> network interface show -role cluster

            Logical         Status     Network            Current     Current Is
Vserver     Interface       Admin/Oper Address/Mask       Node        Port    Home
----------- --------------- ---------- ------------------ ----------- ------- ----
Cluster
            node1-01_clus1  up/up      169.254.36.44/16   node1-01    e7a     true
            node1-01_clus2  up/up      169.254.7.5/16     node1-01    e7b     true
            node1-02_clus1  up/up      169.254.197.206/16 node1-02    e7a     true
            node1-02_clus2  up/up      169.254.195.186/16 node1-02    e7b     true
            node1-03_clus1  up/up      169.254.192.49/16  node1-03    e7a     true
            node1-03_clus2  up/up      169.254.182.76/16  node1-03    e7b     true
            node1-04_clus1  up/up      169.254.59.49/16   node1-04    e7a     true
            node1-04_clus2  up/up      169.254.62.244/16  node1-04    e7b     true

    클러스터 LIF가 홈 포트로 돌아오지 않은 경우 로컬 노드에서 수동으로 되돌립니다.

    network interface revert -vserver Cluster -lif <lif-name>
다음은 무엇인가요?

스위치의 NX-OS를 업그레이드한 후에는 "RCF 설치 또는 업그레이드 개요"부터 시작하여 RCF를 업그레이드합니다.