Skip to main content
O português é fornecido por meio de tradução automática para sua conveniência. O inglês precede o português em caso de inconsistências.

Atualize o NX-OS - Cisco Nexus 9332D-GX2B

Colaboradores netapp-lisa netapp-yvonneo
PDFs

Você atualiza o NX-OS em seus switches Cisco Nexus 9332D-GX2B para oferecer suporte a novo hardware ou a uma nova versão do ONTAP em seu sistema AFX 1K ou AFX 2K.

Observação NetApp recomenda que você conclua primeiro qualquer atualização de software do ONTAP e, em seguida, execute a atualização de software dos seus switches.
Antes de começar

  • Certifique-se de ter um backup atual da configuração do switch.

  • Verifique se o seu cluster está totalmente funcional, ou seja, se não há erros nos logs ou problemas semelhantes.

Sobre esta tarefa

  • Caso necessário, você pode consultar o "Guia de atualização e downgrade do software NX-OS da série Cisco Nexus 9000" para obter mais informações.

  • Caso necessário, você pode consultar o "Matriz de atualização e ISSU para Cisco Nexus 9000 e 3000", que fornece informações sobre a In-Service Software Upgrade (ISSU) para Cisco Nexus 9000 Series Switches com base nas suas versões atual e alvo.

    Na página, selecione Atualização disruptiva e escolha a versão atual e a versão desejada na lista suspensa.

  • A versão do ONTAP em execução no seu sistema AFX determina as versões do NX-OS compatíveis com seus switches.

    • Para switches em um sistema AFX 1K, executando qualquer versão compatível do ONTAP, o NX-OS 10.4.2 e posteriores são compatíveis.

    • Para switches em um sistema AFX 2K, executando ONTAP 9.19.1GA ou posterior, NX-OS 10.6 e versões posteriores são suportados.

      Para obter a lista atual de versões do NX-OS compatíveis, consulte a "Switches Ethernet Cisco NetApp" página.

    Observação Não atualize nem faça downgrade da sua versão do NX-OS para uma versão não suportada.

  • Como este procedimento requer o uso de comandos do ONTAP e comandos dos switches Cisco Nexus 9000 Series, as etapas indicam qual CLI você está usando para inserir os comandos.

  • Os exemplos neste procedimento utilizam a seguinte nomenclatura de interruptor e nó:

    • Os nomes dos dois switches Cisco são cs1 e cs2.

    • Os nomes dos nós são node1-01, node1-02, node1-03 e node1-04.

    • Os nomes do cluster LIF são:

      • node1-01_clus1 e node1-01_clus2 para node1-01

      • node1-02_clus1 e node1-02_clus2 para node1-02

      • node1-03_clus1 e node1-03_clus2 para node1-03

      • node1-04_clus1 e node1-04_clus2 para node1-04

    • O cluster1::*> O prompt indica o nome do cluster.

  • Os exemplos mostrados neste procedimento são para sistemas AFX 1K com switches executando RCF 10.0. Se você tiver um sistema AFX 2K, a entrada e a saída podem variar.

Etapa 1: Prepare-se para atualizar o NX-OS

Prepare-se para atualizar o NX-OS certificando-se de que você possui uma conexão de rede de gerenciamento com cada switch, baixando a versão do NX-OS, verificando o status da porta no cluster e desativando a reversão automática nas LIFs do cluster.

Passos

  1. Conecte cada switch à rede de gerenciamento.

  2. Utilizando a CLI do switch, verifique a conectividade com o servidor que hospeda o NX-OS.

    ping <IP address>

    Mostrar exemplo

    Este exemplo verifica se o switch consegue alcançar o servidor no endereço IP 172.19.2.1:

    cs1# ping 172.19.2.1
Pinging 172.19.2.1 with 0 bytes of data:

Reply From 172.19.2.1: icmp_seq = 0. time= 5910 usec.

  3. Faça o download da versão correta do NX-OS para os switches na "Download do software Cisco" página.

  4. Utilizando a ONTAP CLI, exiba as portas do cluster em cada nó que estão conectadas aos switches do cluster:

    network device-discovery show
    Mostrar exemplo 
    cluster1::*> network device-discovery show

Node/       Local  Discovered
Protocol    Port   Device (LLDP: ChassisID) Interface         Platform
----------- ------ ------------------------ ----------------  ----------------
node1-01/cdp
            e10a   cs1(FLMXXXXXXXX)         Ethernet1/16/3    N9K-C9332D-GX2B
            e10b   cs2(FDOXXXXXXXX)         Ethernet1/16/3    N9K-C9332D-GX2B
            e11a   cs1(FLMXXXXXXXX)         Ethernet1/16/4    N9K-C9332D-GX2B
            e11b   cs2(FDOXXXXXXXX)         Ethernet1/16/4    N9K-C9332D-GX2B
            e1a    cs1(FLMXXXXXXXX)         Ethernet1/16/1    N9K-C9332D-GX2B
            e1b    cs2(FDOXXXXXXXX)         Ethernet1/16/1    N9K-C9332D-GX2B
            .
            .
            .
            e7a    cs1(FLMXXXXXXXX)         Ethernet1/16/2    N9K-C9332D-GX2B
            e7b    cs2(FDOXXXXXXXX)         Ethernet1/16/2    N9K-C9332D-GX2B

node1-01/lldp
            e10a   cs1 (c8:60:8f:xx:xx:xx)  Ethernet1/16/3    -
            e10b   cs2 (04:e3:87:xx:xx:xx)  Ethernet1/16/3    -
            e11a   cs1 (c8:60:8f:xx:xx:xx)  Ethernet1/16/4    -
            e11b   cs2 (04:e3:87:xx:xx:xx)  Ethernet1/16/4    -
            e1a    cs1 (c8:60:8f:xx:xx:xx)  Ethernet1/16/1    -
            e1b    cs2 (04:e3:87:xx:xx:xx)  Ethernet1/16/1    -
            .
            .
            .
            e7a    cs1 (c8:60:8f:34:78:d3)  Ethernet1/16/2    -
            e7b    cs2 (04:e3:87:19:a2:59)  Ethernet1/16/2    -
.
.
.

  5. Utilizando a ONTAP CLI, verifique o status administrativo e operacional de cada porta:

    1. Portas de cluster

      1. Verifique se todas as portas do cluster estão ativas e com status íntegro:

        network port show -ipspace Cluster
        Mostrar exemplo 
        cluster1::*> network port show -ipspace Cluster

Node: node1-01
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/100000 healthy false
e7b       Cluster      Cluster          up   9000  auto/100000 healthy false

Node: node1-02
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/100000 healthy false
e7b       Cluster      Cluster          up   9000  auto/100000 healthy false

Node: node1-03

                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/10000 healthy  false
e7b       Cluster      Cluster          up   9000  auto/10000 healthy  false

Node: node1-04
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/10000 healthy  false
e7b       Cluster      Cluster          up   9000  auto/10000 healthy  false

      2. Verifique se todas as interfaces de cluster (LIFs) estão na porta principal:

        network interface show -role cluster
        Mostrar exemplo 
        cluster1::*> network interface show -role cluster

            Logical         Status     Network            Current   Current Is
Vserver     Interface       Admin/Oper Address/Mask       Node      Port    Home
----------- --------------- ---------- ------------------ --------- ------- ----
Cluster
            node1-01_clus1  up/up      169.254.36.44/16   node1-01  e7a     true
            node1-01_clus2  up/up      169.254.7.5/16     node1-01  e7b     true
            node1-02_clus1  up/up      169.254.197.206/16 node1-02  e7a     true
            node1-02_clus2  up/up      169.254.195.186/16 node1-02  e7b     true
            node1-03_clus1  up/up      169.254.192.49/16  node1-03  e7a     true
            node1-03_clus2  up/up      169.254.182.76/16  node1-03  e7b     true
            node1-04_clus1  up/up      169.254.59.49/16   node1-04  e7a     true
            node1-04_clus2  up/up      169.254.62.244/16  node1-04  e7b     true

8 entries were displayed.

      3. Verifique se o cluster exibe informações para ambos os switches do cluster:

        system cluster-switch show -is-monitoring-enabled-operational true
        Mostrar exemplo 
        cluster1::*> system cluster-switch show -is-monitoring-enabled-operational true

Switch                      Type               Address          Model
--------------------------- ------------------ ---------------- ---------------
cs2(FDOXXXXXXXX)            cluster-network    10.228.137.233   N9K-C9332D-GX2B
     Serial Number: FDOXXXXXXXX
      Is Monitored: true
            Reason: None
  Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                    10.4(2)
    Version Source: CDP/ISDP


cs1(FLMXXXXXXXX)             cluster-network   10.228.137.253   N9K-C9332D-GX2B
     Serial Number: FLMXXXXXXXX
      Is Monitored: true
            Reason: None
  Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                    10.4(2)
    Version Source: CDP/ISDP

2 entries were displayed.

    2. Portas HA

      1. Verifique se todas as portas HA estão ativas e com status íntegro:

        ha interconnect status show -node <node-name>
        Mostrar exemplo 
        cluster1::*> ha interconnect status show -node node1-01
  (system ha interconnect status show)

                       Node: node1-01
              Link 0 Status: up
              Link 1 Status: up
           Is Link 0 Active: true
           Is Link 1 Active: true
         IC RDMA Connection: up
                       Slot: 0
             Debug Firmware: no


Interconnect Port 0 :
                  Port Name: e1a-17
                        MTU: 4096
           Link Information: ACTIVE


Interconnect Port 1 :
                  Port Name: e1b-18
                        MTU: 4096
           Link Information: ACTIVE

cluster1::*> ha interconnect status show -node node1-02
  (system ha interconnect status show)

                       Node: node1-02
              Link 0 Status: up
              Link 1 Status: up
           Is Link 0 Active: true
           Is Link 1 Active: true
         IC RDMA Connection: up
                       Slot: 0
             Debug Firmware: no


Interconnect Port 0 :
                  Port Name: e1a-17
                        MTU: 4096
           Link Information: ACTIVE


Interconnect Port 1 :
                  Port Name: e1b-18
                        MTU: 4096
           Link Information: ACTIVE
.
.
.

    3. Portas de armazenamento

      1. Verifique se todas as portas de armazenamento estão ativas e com status íntegro:

        storage port show -port-type ENET
        Mostrar exemplo 
        cluster1::*> storage port show -port-type ENET


                                      Speed
Node               Port Type  Mode    (Gb/s) State    Status
------------------ ---- ----- ------- ------ -------- -----------
node1-01
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
                   e11b ENET  -          100 enabled  online
node1-02
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
                   e11b ENET  -          100 enabled  online
node1-03
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
node1-04
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
                   e11b ENET  -          100 enabled  online
16 entries were displayed.

    4. Portas de prateleira de armazenamento

      1. Verifique se todas as portas da prateleira de armazenamento estão ativas e com status íntegro:

        storage shelf port show
        Mostrar exemplo 
        cluster1::*> storage shelf port show

Shelf ID Module State        Internal?
----- -- ------ ------------ ---------
1.1
       0 A      connected    false
       1 A      connected    false
       2 A      connected    false
       3 A      connected    false
       4 A      connected    false
       5 A      connected    false
       6 A      connected    false
       7 A      connected    false
       8 B      connected    false
       9 B      connected    false
      10 B      connected    false
      11 B      connected    false
      12 B      connected    false
      13 B      connected    false
      14 B      connected    false
      15 B      connected    false

16 entries were displayed.

      2. Verifique o status da conexão de todas as portas da prateleira de armazenamento:

        storage shelf port show -fields remote-device,remote-port,connector-state
        Mostrar exemplo 
        cluster1::*> storage shelf port show -fields remote-device,remote-port,connector-state

shelf id connector-state remote-port    remote-device
----- -- --------------- -------------- -----------------
1.1   0  connected       Ethernet1/17/1 CX9332D-cs1
1.1   1  connected       Ethernet1/15/1 CX9364D-cs1
1.1   2  connected       Ethernet1/17/2 CX9332D-cs1
1.1   3  connected       Ethernet1/15/2 CX9364D-cs1
1.1   4  connected       Ethernet1/17/3 CX9332D-cs1
1.1   5  connected       Ethernet1/15/3 CX9364D-cs1
1.1   6  connected       Ethernet1/17/4 CX9332D-cs1
1.1   7  connected       Ethernet1/15/4 CX9364D-cs1
1.1   8  connected       Ethernet1/19/1 CX9332D-cs1
1.1   9  connected       Ethernet1/17/1 CX9364D-cs1
1.1   10 connected       Ethernet1/19/2 CX9332D-cs1
1.1   11 connected       Ethernet1/17/2 CX9364D-cs1
1.1   12 connected       Ethernet1/19/3 CX9332D-cs1
1.1   13 connected       Ethernet1/17/3 CX9364D-cs1
1.1   14 connected       Ethernet1/19/4 CX9332D-cs1
1.1   15 connected       Ethernet1/17/4 CX9364D-cs1

16 entries were displayed.

  6. Usando a ONTAP CLI, desative a reversão automática nas LIFs do cluster. As LIFs do cluster farão failover para o switch do cluster parceiro e permanecerão lá enquanto você executa este procedimento no switch de destino:

    network interface modify -vserver Cluster -lif * -auto-revert false

Etapa 2: Instale o NX-OS

Você instala o NX-OS no primeiro switch (cs1) instalando e verificando as novas versões do NX-OS e do EPLD, verificando a integridade de todas as portas no cluster e, em seguida, repetindo essas etapas no segundo switch (cs2).

  1. Utilizando a CLI do switch, copie as imagens do NX-OS e do EPLD para um switch.

    Você usa esse comando duas vezes: a primeira vez é para copiar a versão do NX-OS e a segunda vez é para copiar a versão do EPLD.

    copy <protocol>: bootflash: vrf management

    Mostrar exemplo

    O exemplo utiliza sftp.

    cs1# copy sftp: bootflash: vrf management
Enter source filename: /code/nxos.10.4.2.bin
Enter hostname for the sftp server: 172.19.2.1
Enter username: root

Outbound-ReKey for 172.19.2.1:22
Inbound-ReKey for 172.19.2.1:22
root@172.19.2.1's password:
sftp> progress
Progress meter enabled
sftp> get   /code/nxos.10.4.2.bin  /bootflash/nxos.10.4.2.bin
/code/nxos.10.4.2.bin  100% 1261MB   9.3MB/s   02:15
sftp> exit
Copy complete, now saving to disk (please wait)...
Copy complete.

cs1# copy sftp: bootflash: vrf management
Enter source filename: /code/n9000-epld.10.4.2.F.img
Enter hostname for the sftp server: 172.19.2.1
Enter username: user1

Outbound-ReKey for 172.19.2.1:22
Inbound-ReKey for 172.19.2.1:22
user1@172.19.2.1's password:
sftp> progress
Progress meter enabled
sftp> get   /code/n9000-epld.10.4.2.F.img  /bootflash/n9000-epld.10.4.2.F.img
/code/n9000-epld.10.4.2.F.img  100%  161MB   9.5MB/s   00:16
sftp> exit
Copy complete, now saving to disk (please wait)...
Copy complete.

  2. Utilizando a CLI do switch, verifique a versão do NX-OS em execução:

    show version

    Mostrar exemplo 
    cs1# show version
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (C) 2002-2025, Cisco and/or its affiliates.
All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under their own
licenses, such as open source.  This software is provided "as is," and unless
otherwise stated, there is no warranty, express or implied, including but not
limited to warranties of merchantability and fitness for a particular purpose.
Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or
GNU General Public License (GPL) version 3.0  or the GNU
Lesser General Public License (LGPL) Version 2.1 or
Lesser General Public License (LGPL) Version 2.0.
A copy of each such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://opensource.org/licenses/gpl-3.0.html and
http://www.opensource.org/licenses/lgpl-2.1.php and
http://www.gnu.org/licenses/old-licenses/library.txt.


Software
  BIOS: version 01.14
  NXOS: version 10.4(1) [Feature Release]
  Host NXOS: version 10.4(1)
  BIOS compile time:  11/25/2024
  NXOS image file is: bootflash:///nxos64-cs.10.4.1.F.bin
  NXOS compile time:  11/30/2023 12:00:00 [12/14/2023 05:25:50]
  NXOS boot mode: LXC


Hardware
  cisco Nexus9000 C9332D-GX2B Chassis
  Intel(R) Xeon(R) CPU D-1633N @ 2.50GHz with 32802156 kB of memory.
  Processor Board ID FLMXXXXXXXX
  Device name: cs2
  bootflash:  115802886 kB


Kernel uptime is 5 day(s), 2 hour(s), 13 minute(s), 21 second(s)


Last reset at 3580 usecs after Thu Jun  5 15:55:08 2025
  Reason: Reset Requested by CLI command reload
  System version: 10.4(1)
  Service:


plugin
  Core Plugin, Ethernet Plugin


Active Package(s):

cs1#

  3. Usando a CLI do switch, instale a imagem do NX-OS.

    A instalação do arquivo de imagem faz com que ele seja carregado sempre que o switch for reiniciado.

    install all nxos bootflash:nxos.<version number>.bin

    Mostrar exemplo

    O exemplo utiliza a versão 10.4.2 do NX-OS.

    cs1# install all nxos bootflash:nxos.10.4.2.bin

Installer will perform compatibility check first. Please wait.
Installer is forced disruptive

Verifying image bootflash:/nxos.10.4.2.bin for boot variable "nxos".
[] 100% -- SUCCESS

Verifying image type.
[] 100% -- SUCCESS

Preparing "nxos" version info using image bootflash:/nxos.10.4.2.bin.
[] 100% -- SUCCESS

Preparing "bios" version info using image bootflash:/nxos.10.4.2.bin.
[] 100% -- SUCCESS

Performing module support checks.
[] 100% -- SUCCESS

Notifying services about system upgrade.
[] 100% -- SUCCESS


Compatibility check is done:
Module  Bootable  Impact          Install-type  Reason
------  --------  --------------- ------------  ---------
  1     yes       Disruptive      Reset         Default upgrade is not hitless



Images will be upgraded according to following table:

Module   Image    Running-Version(pri:alt)                 New-Version         Upg-Required
------- --------- ---------------------------------------- ------------------- ------------
  1      nxos     10.4(1)                                  10.4(2)             Yes
  1      bios     xx.xx.:xx.xx                             xxx                 No


Switch will be reloaded for disruptive upgrade.

Do you want to continue with the installation (y/n)? [n] y

Install is in progress, please wait.

Performing runtime checks.
[] 100% -- SUCCESS

Setting boot variables.
[] 100% -- SUCCESS

Performing configuration copy.
[] 100% -- SUCCESS

Module 1: Refreshing compact flash and upgrading bios/loader/bootrom.
Warning: please do not remove or power off the module at this time.
[] 100% -- SUCCESS

Finishing the upgrade, switch will reboot in 10 seconds.

  4. Utilizando a CLI do switch, verifique a nova versão do NX-OS após a reinicialização do switch:

    show version

    Mostrar exemplo 
    cs1# show version
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (C) 2002-2025, Cisco and/or its affiliates.
All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under their own
licenses, such as open source.  This software is provided "as is," and unless
otherwise stated, there is no warranty, express or implied, including but not
limited to warranties of merchantability and fitness for a particular purpose.
Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or
GNU General Public License (GPL) version 3.0  or the GNU
Lesser General Public License (LGPL) Version 2.1 or
Lesser General Public License (LGPL) Version 2.0.
A copy of each such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://opensource.org/licenses/gpl-3.0.html and
http://www.opensource.org/licenses/lgpl-2.1.php and
http://www.gnu.org/licenses/old-licenses/library.txt.


Software
  BIOS: version 01.14
  NXOS: version 10.4(2) [Feature Release]
  Host NXOS: version 10.4(2)
  BIOS compile time:  11/25/2024
  NXOS image file is: bootflash:///nxos64-cs.10.4.2.F.bin
  NXOS compile time:  11/30/2023 12:00:00 [12/14/2023 05:25:50]
  NXOS boot mode: LXC


Hardware
  cisco Nexus9000 C9332D-GX2B Chassis
  Intel(R) Xeon(R) CPU D-1633N @ 2.50GHz with 32802156 kB of memory.
  Processor Board ID FLMXXXXXXXX
  Device name: cs2
  bootflash:  115802886 kB


Kernel uptime is 5 day(s), 2 hour(s), 13 minute(s), 21 second(s)


Last reset at 3580 usecs after Thu Jun  5 15:55:08 2025
  Reason: Reset Requested by CLI command reload
  System version: 10.4(2)
  Service:


plugin
  Core Plugin, Ethernet Plugin


Active Package(s):

cs1#

  5. Utilizando a CLI do switch, atualize a imagem EPLD usando os seguintes comandos:

    show version module 1 epld

    install epld bootflash:n9000-epld.<version>.img module all

    Após a execução do último comando, o switch reinicializa.

    Mostrar exemplo

    O exemplo utiliza a versão 10.4.2.F do EPLD

    cs1# show version module 1 epld

EPLD Device                     Version
---------------------------------------
MI   FPGA                        0x7
IO   FPGA                        0x17
MI   FPGA2                       0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2

cs1# install epld bootflash:n9000-epld.10.4.2.F.img module all
Compatibility check:
Module        Type         Upgradable        Impact    Reason
------  ------------------ ----------------- --------- -----------
     1         SUP         Yes       disruptive  Module Upgradable

Retrieving EPLD versions.... Please wait.
Images will be upgraded according to following table:
Module  Type   EPLD              Running-Version   New-Version  Upg-Required
------- ------ ----------------- ----------------- ------------ ------------
     1  SUP    MI FPGA           0x07              0x07         No
     1  SUP    IO FPGA           0x17              0x19         Yes
     1  SUP    MI FPGA2          0x02              0x02         No
The above modules require upgrade.
The switch will be reloaded at the end of the upgrade
Do you want to continue (y/n) ?  [n] y

Proceeding to upgrade Modules.

Starting Module 1 EPLD Upgrade

Module 1 : IO FPGA [Programming] : 100.00% (     64 of      64 sectors)
Module 1 EPLD upgrade is successful.
Module   Type  Upgrade-Result
-------- ----- --------------
     1   SUP   Success

EPLDs upgraded.

Module 1 EPLD upgrade is successful.

  6. Após a reinicialização do switch, use a CLI do switch para fazer login e verificar se a nova versão do EPLD foi carregada com sucesso.

    show version module 1 epld

    Mostrar exemplo 
    cs1# show version module 1 epld

EPLD Device                     Version
---------------------------------------
MI   FPGA                        0x7
IO   FPGA                        0x19
MI   FPGA2                       0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2

  7. Utilizando a CLI do ONTAP, verifique a integridade de todas as portas no cluster.

    1. Portas de cluster

      1. Verifique se as portas do cluster estão ativas e funcionando corretamente em todos os nós do cluster:

        network port show -ipspace Cluster
        Mostrar exemplo 
        cluster1::*> network port show -ipspace Cluster

Node: node1-01
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/10000 healthy  false
e7b       Cluster      Cluster          up   9000  auto/10000 healthy  false

Node: node1-02
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/10000 healthy  false
e7b       Cluster      Cluster          up   9000  auto/10000 healthy  false

Node: node1-03
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/100000 healthy false
e7b       Cluster      Cluster          up   9000  auto/100000 healthy false

Node: node1-04
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/100000 healthy false
e7b       Cluster      Cluster          up   9000  auto/100000 healthy false

      2. Verifique o estado de funcionamento do switch no cluster:

        network device-discovery show -protocol cdp
        system cluster-switch show -is-monitoring-enabled-operational true
        Mostrar exemplo 
        cluster1::*> network device-discovery show -protocol cdp

node1-02/cdp
            e10a   cs1(FLMXXXXXXXX)         Ethernet1/16/3    N9K-C9332D-GX2B
            e10b   cs2(FDOXXXXXXXX)         Ethernet1/16/3    N9K-C9332D-GX2B
            e11a   cs1(FLMXXXXXXXX)         Ethernet1/16/4    N9K-C9332D-GX2B
            e11b   cs2(FDOXXXXXXXX)         Ethernet1/16/4    N9K-C9332D-GX2B
            e1a    cs1(FLMXXXXXXXX)         Ethernet1/16/1    N9K-C9332D-GX2B
            e1b    cs2(FDOXXXXXXXX)         Ethernet1/16/1    N9K-C9332D-GX2B
            .
            .
            .
            e7a    cs1(FLM284504N6)         Ethernet1/16/2    N9K-C9332D-GX2B
            e7b    cs2(FDO2846056X)         Ethernet1/16/2    N9K-C9332D-GX2B

node1-01/cdp
            e10a   cs1(FLMXXXXXXXX)         Ethernet1/16/3    N9K-C9332D-GX2B
            e10b   cs2(FDOXXXXXXXX)         Ethernet1/16/3    N9K-C9332D-GX2B
            e11a   cs1(FLMXXXXXXXX)         Ethernet1/16/4    N9K-C9332D-GX2B
            e11b   cs2(FDOXXXXXXXX)         Ethernet1/16/4    N9K-C9332D-GX2B
            e1a    cs1(FLMXXXXXXXX)         Ethernet1/16/1    N9K-C9332D-GX2B
            e1b    cs2(FDOXXXXXXXX)         Ethernet1/16/1    N9K-C9332D-GX2B
           .
           .
           .
            e7a    cs1(FLMXXXXXXXX)         Ethernet1/16/2    N9K-C9332D-GX2B
            e7b    cs2(FDOXXXXXXXX)         Ethernet1/16/2    N9K-C9332D-GX2B
.
.
.

cluster1::*> system cluster-switch show -is-monitoring-enabled-operational true
Switch                      Type               Address          Model
--------------------------- ------------------ ---------------- ---------------
cs2(FDOXXXXXXXX)            cluster-network    10.228.137.233   N9K-C9332D-GX2B
     Serial Number: FDOXXXXXXXX
      Is Monitored: true
            Reason: None
  Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                    10.4(2)
    Version Source: CDP/ISDP


cs1(FLMXXXXXXXX)             cluster-network   10.228.137.253   N9K-C9332D-GX2B
     Serial Number: FLMXXXXXXXX
      Is Monitored: true
            Reason: None
  Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                    10.4(2)
    Version Source: CDP/ISDP

    2. Portas HA

      1. Verifique se todas as portas HA estão ativas e com status íntegro:

        ha interconnect status show -node <node-name>
        Mostrar exemplo 
        cluster1::*> ha interconnect status show -node node1-01
  (system ha interconnect status show)

                       Node: node1-01
              Link 0 Status: up
              Link 1 Status: up
           Is Link 0 Active: true
           Is Link 1 Active: true
         IC RDMA Connection: up
                       Slot: 0
             Debug Firmware: no


Interconnect Port 0 :
                  Port Name: e1a-17
                        MTU: 4096
           Link Information: ACTIVE


Interconnect Port 1 :
                  Port Name: e1b-18
                        MTU: 4096
           Link Information: ACTIVE

cluster1::*> ha interconnect status show -node node1-02
  (system ha interconnect status show)

                       Node: node1-02
              Link 0 Status: up
              Link 1 Status: up
           Is Link 0 Active: true
           Is Link 1 Active: true
         IC RDMA Connection: up
                       Slot: 0
             Debug Firmware: no


Interconnect Port 0 :
                  Port Name: e1a-17
                        MTU: 4096
           Link Information: ACTIVE


Interconnect Port 1 :
                  Port Name: e1b-18
                        MTU: 4096
           Link Information: ACTIVE
.
.
.

    3. Portas de armazenamento

      1. Verifique se todas as portas de armazenamento estão ativas e com status íntegro:

        storage port show -port-type ENET
        Mostrar exemplo 
        cluster1::*> storage port show -port-type ENET


                                      Speed
Node               Port Type  Mode    (Gb/s) State    Status
------------------ ---- ----- ------- ------ -------- -----------
node1-01
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
                   e11b ENET  -          100 enabled  online
node1-02
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
                   e11b ENET  -          100 enabled  online
node1-03
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
node1-04
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
                   e11b ENET  -          100 enabled  online
16 entries were displayed.

    4. Portas de prateleira de armazenamento

      1. Verifique se todas as portas da prateleira de armazenamento estão ativas e com status íntegro:

        storage shelf port show
        Mostrar exemplo 
        cluster1::*> storage shelf port show

Shelf ID Module State        Internal?
----- -- ------ ------------ ---------
1.1
       0 A      connected    false
       1 A      connected    false
       2 A      connected    false
       3 A      connected    false
       4 A      connected    false
       5 A      connected    false
       6 A      connected    false
       7 A      connected    false
       8 B      connected    false
       9 B      connected    false
      10 B      connected    false
      11 B      connected    false
      12 B      connected    false
      13 B      connected    false
      14 B      connected    false
      15 B      connected    false

16 entries were displayed.

      2. Verifique o status da conexão de todas as portas da prateleira de armazenamento:

        storage shelf port show -fields remote-device,remote-port,connector-state
        Mostrar exemplo 
        cluster1::*> storage shelf port show -fields remote-device,remote-port,connector-state

shelf id connector-state remote-port    remote-device
----- -- --------------- -------------- -----------------
1.1   0  connected       Ethernet1/17/1 CX9332D-cs1
1.1   1  connected       Ethernet1/15/1 CX9364D-cs1
1.1   2  connected       Ethernet1/17/2 CX9332D-cs1
1.1   3  connected       Ethernet1/15/2 CX9364D-cs1
1.1   4  connected       Ethernet1/17/3 CX9332D-cs1
1.1   5  connected       Ethernet1/15/3 CX9364D-cs1
1.1   6  connected       Ethernet1/17/4 CX9332D-cs1
1.1   7  connected       Ethernet1/15/4 CX9364D-cs1
1.1   8  connected       Ethernet1/19/1 CX9332D-cs1
1.1   9  connected       Ethernet1/17/1 CX9364D-cs1
1.1   10 connected       Ethernet1/19/2 CX9332D-cs1
1.1   11 connected       Ethernet1/17/2 CX9364D-cs1
1.1   12 connected       Ethernet1/19/3 CX9332D-cs1
1.1   13 connected       Ethernet1/17/3 CX9364D-cs1
1.1   14 connected       Ethernet1/19/4 CX9332D-cs1
1.1   15 connected       Ethernet1/17/4 CX9364D-cs1

16 entries were displayed.

  8. Usando a ONTAP CLI, verifique se o cluster está íntegro:

    cluster show
    Mostrar exemplo 
    cluster1::*> cluster show


Node                 Health  Eligibility   Epsilon
-------------------- ------- ------------  ------------
node1-01             true    true          false
node1-02             true    true          false
node1-03             true    true          false
node1-04             true    true          true

4 entries were displayed.

  9. Repita estes passos para instalar as imagens NX-OS e EPLD no switch cs2.

Etapa 3: conclua a atualização do NX-OS

Utilizando a ONTAP CLI, conclua a atualização do NX-OS reativando a reversão automática nas LIFs do cluster e verificando se as LIFs do cluster retornaram às suas portas iniciais.

  1. Reative a reversão automática nos LIFs do cluster.

    network interface modify -vserver Cluster -lif * -auto-revert true

  2. Verifique se as LIFs do cluster retornaram à sua porta original:

    network interface show -role cluster
    Mostrar exemplo 
    cluster1::*> network interface show -role cluster

            Logical         Status     Network            Current     Current Is
Vserver     Interface       Admin/Oper Address/Mask       Node        Port    Home
----------- --------------- ---------- ------------------ ----------- ------- ----
Cluster
            node1-01_clus1  up/up      169.254.36.44/16   node1-01    e7a     true
            node1-01_clus2  up/up      169.254.7.5/16     node1-01    e7b     true
            node1-02_clus1  up/up      169.254.197.206/16 node1-02    e7a     true
            node1-02_clus2  up/up      169.254.195.186/16 node1-02    e7b     true
            node1-03_clus1  up/up      169.254.192.49/16  node1-03    e7a     true
            node1-03_clus2  up/up      169.254.182.76/16  node1-03    e7b     true
            node1-04_clus1  up/up      169.254.59.49/16   node1-04    e7a     true
            node1-04_clus2  up/up      169.254.62.244/16  node1-04    e7b     true

    Se alguma LIF do cluster não tiver retornado às suas portas originais, reverta-as manualmente a partir do nó local:

    network interface revert -vserver Cluster -lif <lif-name>
O que vem a seguir?

Depois de atualizar o NX-OS em seus switches, você atualiza o RCF começando pelo "Instalar ou atualizar a visão geral do RCF".