Depending on your requirements, there are several configuration settings for Storage Nodes that you can apply.
Service/ Component | Attribute Name | Code | Description |
---|---|---|---|
LDR | HTTP State | HSTE | HSTE is related to the HTTP protocol for all LDR traffic, including S3, Swift, and other internal StorageGRID traffic. Set the LDR service to one of the following choices:
|
Auto-Start HTTP | HTAS | HTAS is related to the HTTP protocol for all LDR traffic, including S3, Swift, and other internal StorageGRID traffic. Enable the HTTP component when the LDR service is restarted. If not selected, the HTTP interface remains Offline until explicitly enabled. If Auto-Start HTTP is selected, the state of the system on restart depends on the state of the component. If the component is Read-only on restart, the HTTP interface is also Read-only. If the component is Online, then HTTP is also Online. Otherwise, the HTTP interface remains in the Offline state. |
|
Reset Lost Objects Count | RCOR | Reset to zero the counter for the number of lost objects on this service. | |
Storage State – Desired | SSDS | A user-configurable setting for the desired state of the storage component. The LDR service reads this value and attempts to match the status indicated by this attribute. The value is persistent across restarts. For example, you can use this setting to force storage to become read-only even when there is ample available storage space. This can be useful for troubleshooting. The attribute can take one of the following values:
|
|
Health Check Timeout | SHCT | The time limit in seconds within which a health check test must complete in order for a storage volume to be considered healthy. Only change this value when directed to do so by Support. | |
Reset Missing Objects Count | VCMI | Resets the count of Missing Objects Detected (OMIS). Use only after foreground verification completes. Missing replicated object data is restored automatically by the StorageGRID system. | |
Verify | FVOV | Select object stores on which to perform foreground verification. | |
Verification Rate | VPRI | Set the priority rate at which background verification takes place. See information on configuring the background verification rate. | |
Reset Corrupt Objects Count | VCCR | Reset the counter for corrupt replicated object data found during background verification. This option can be used to clear the Corrupt Objects Detected (OCOR) alarm condition. For details, see the information about troubleshooting. | |
Reset Writes Failure Count | RSWF | Reset to zero the counter for write failures of erasure-coded object data to the Storage Node. | |
Reset Reads Failure Count | RSRF | Reset to zero the counter for read failures of erasure-coded object data from the Storage Node. | |
Reset Deletes Failure Count | RSDF | Reset to zero the counter for delete failures of erasure-coded object data from the Storage Node. | |
Reset Corrupt Copies Detected Count | RSCC | Reset to zero the counter for the number of corrupt copies of erasure-coded object data on the Storage Node. | |
Reset Corrupt Fragments Detected Count | RSCD | Reset to zero the counter for corrupt fragments of erasure-coded object data on the Storage Node. | |
Reset Missing Fragments Detected Count | RSMD | Reset to zero the counter for missing fragments of erasure-coded object data on the Storage Node. Use only after foreground verification completes. | |
Reset Inbound Replication Failure Count | RICR | Reset to zero the counter for inbound replication failures. This can be used to clear the RIRF (Inbound Replication – Failed) alarm. | |
Reset Outbound Replication Failure Count | ROCR | Reset to zero the counter for outbound replication failures. This can be used to clear the RORF (Outbound Replications – Failed) alarm. | |
Disable Inbound Replication | DSIR | Select to disable inbound replication as part of a maintenance or testing procedure. Leave unchecked during normal operation. When inbound replication is disabled, objects can be retrieved from the Storage Node for copying to other locations in the StorageGRID system, but objects cannot be copied to this Storage Node from other locations: the LDR service is read-only. |
|
Disable Outbound Replication | DSOR | Select to disable outbound replication (including content requests for HTTP retrievals) as part of a maintenance or testing procedure. Leave unchecked during normal operation. When outbound replication is disabled, objects can be copied to this Storage Node, but objects cannot be retrieved from the Storage Node to be copied to other locations in the StorageGRID system. The LDR service is write-only. |
|
Reset HTTP Counts | LHAC | Reset to zero the counter for all HTTP transactions. |