Viewing information about appliance Admin Nodes and Gateway Nodes

The Nodes page lists information about service health and all computational, disk device, and network resources for each services appliance that is used for an Admin Node or a Gateway Node. You can also see memory, storage hardware, network resources, network interfaces, network addresses, and receipt and transmittal information.


  1. From the Nodes page, select an appliance Admin Node or an appliance Gateway Node.
  2. Select Overview.
    The Node Information table on the Overview tab displays the node's ID and name, the node type, the software version installed, and the IP addresses associated with the node. The Interface column contains the name of the interface, as follows:
    • adllb and adlli are shown if active/backup bonding is used for the Admin Network interface
    • eth is the Grid Network, Admin Network, or Client Network
    • hic is a bonded port
    • mtc are the management IP addresses on the appliance

    Nodes Page Overview tab for services appliance
  3. Select Hardware to see more information about the appliance.
    1. View the CPU Utilization and Memory graphs to determine the percentages of CPU and memory usage over time. To display a different time interval, select one of the controls above the chart or graph. You can display the information available for intervals of 1 hour, 1 day, 1 week, 1 month, or 1 year. You can also set a custom interval, which allows you to specify date and time ranges.

      Nodes page Hardware tab graphs for services appliance
    2. Scroll down to view the table of components for the appliance. This table contains information such as the model name, serial number, and the status of each component.

      Nodes page Hardware tab for services appliance
      Field in the Appliance table Description
      Appliance Model The model number for this StorageGRID appliance.
      Storage Controller Failed Drive Count The number of drives that are not optimal.
      Storage Data Drive Type The type of drives in the appliance, such as HDD (hard disk drive) or SSD (solid state drive).
      Storage Data Drive Size The total capacity including all data drives in the appliance.
      Storage RAID Mode The RAID mode for the appliance.
      Overall Power Supply The status of all power supplies in the appliance.
      Compute Controller BMC IP The IP address of the baseboard management controller (BMC) port in the compute controller.

      You can use this IP to connect to the BMC interface to monitor and diagnose the appliance hardware.

      Compute Controller Serial Number The serial number of the compute controller.
      Compute Hardware The status of the compute controller hardware.
      Compute Controller CPU Temperature The temperature status of the compute controller's CPU.
      Compute Controller Chassis Temperature The temperature status of the compute controller.
    3. Confirm that all statuses are "Nominal."
      The statuses in this section correspond to the following alarm codes.
      Field Alarm code
      Storage Multipath Connectivity APMS
      Storage Controller Failed Drive Count BADD
      Compute Controller Chassis Temperature BRDT
      Compute Controller Hardware CCNA
      Compute Controller Power Supply A CPSA
      Compute Controller Power Supply B CPSB
      Compute Controller CPU Temperature CPUT
      Overall Power Supply OPST
  4. Select Network to view information for each network.

    The Network Traffic graph provides a summary of overall network traffic.
    Nodes Page Network Traffic Graph

    1. Review the Network Interfaces section.

      Nodes Page Hardware Tab Network Services Appliance
      Use the following table with the values in the Speed column in the Network Interfaces table to determine whether the four 40/100-GbE network ports on the appliance were configured to use active/backup mode or LACP mode.
      Note: The values shown in the table assume all four links are used.
      Link mode Bond mode Individual HIC link speed (hic1, hic2, hic3, hic4) Expected Grid/Client Network speed (eth0, eth2)
      Aggregate LACP 100 400
      Fixed LACP 100 200
      Fixed Active/Backup 100 100
      Aggregate LACP 40 160
      Fixed LACP 40 80
      Fixed Active/Backup 40 40
    2. Review the Network Communication section.
      The Receive and Transmit tables show how many bytes and packets have been received and sent across each network as well as other receive and transmission metrics.
      Nodes Page Network Comm
  5. Select Storage to view information about the disk devices and volumes on the services appliance.

    Nodes Page Storage Tab Services Appliance