Configure RHEL 10.0 for NVMe-oF with ONTAP storage

10/08/2025 Contributors

Red Hat Enterpirse Linux (RHEL) hosts support the NVMe over Fibre Channel (NVMe/FC) and NVMe over TCP (NVMe/TCP) protocols with Asymmetric Namespace Access (ANA). ANA provides multipathing functionality equivalent to asymmetric logical unit access (ALUA) in iSCSI and FCP environments.

Learn how to configure NVMe over Fabrics (NVMe-oF) hosts for RHEL 10.0. For more support and feature information, see NVME-oF Overview.

NVMe-oF with RHEL 10.0 has the following known limitations:

DM multipath support for NVMe-oF is not supported.
Avoid issuing the nvme disconnect-all command on systems booting from SAN over NVMe-TCP or NVMe-FC namespaces because it disconnects both root and data filesystems and might lead to system instability.

Step 1: Optionally, enable SAN booting

You can configure your host to use SAN booting to simplify deployment and improve scalability. Use the Interoperability Matrix Tool to verify that your Linux OS, host bus adapter (HBA), HBA firmware, HBA boot BIOS, and ONTAP version support SAN booting.

Steps

Create a NVMe namespace and map it to the host.
Enable SAN booting in the server BIOS for the ports to which the SAN boot namespace is mapped.

For information on how to enable the HBA BIOS, see your vendor-specific documentation.
Reboot the host and verify that the OS is up and running.

Step 2: Verify the software version and NVMe configuration

Check that your system meets software requirements and verify NVMe package installations and host configuration.

Steps

Install RHEL 10.0 on the server. After the installation is complete, verify that you are running the required RHEL 10.0 kernel:
```
uname -r
```
Example RHEL kernel version:
```
6.12.0-55.9.1.el10_0.x86_64
```
Install the nvme-cli package:
```
rpm -qa|grep nvme-cli
```
The following example shows an nvme-cli package version:
```
nvme-cli-2.11-5.el10.x86_64
```
Install the libnvme package:
```
rpm -qa|grep libnvme
```
The following example shows an libnvme package version:
```
libnvme-1.11.1-1.el10.x86_64
```
On the host, check the hostnqn string at /etc/nvme/hostnqn:
```
cat /etc/nvme/hostnqn
```
The following example shows an hostnqn version:
```
nqn.2014-08.org.nvmexpress:uuid:4c4c4544-0056-5410-8048-b9c04f425633
```

Verify that the hostnqn string matches the hostnqn string for the corresponding subsystem on the ONTAP array:

::> vserver nvme subsystem host show -vserver vs_nvme_194_rhel10

Show example

Vserver Subsystem Priority  Host NQN
------- --------- --------  ------------------------------------------------
vs_ nvme_194_rhel10
        nvme4
                  regular   nqn.2014-08.org.nvmexpress:uuid:4c4c4544-0056-5410-8048- c7c04f425633
        nvme_1
                  regular   nqn.2014-08.org.nvmexpress:uuid:4c4c4544-0056-5410-8048- c7c04f425633
        nvme_2
                  regular   nqn.2014-08.org.nvmexpress:uuid:4c4c4544-0056-5410-8048- c7c04f425633
        nvme_3
                  regular   nqn.2014-08.org.nvmexpress:uuid:4c4c4544-0056-5410-8048- c7c04f425633
4 entries were displayed.

If the hostnqn strings do not match, use the vserver modify command to update the hostnqn string on your corresponding ONTAP storage system subsystem to match the hostnqn string from /etc/nvme/hostnqn on the host.

Step 3: Configure NVMe/FC and NVMe/TCP

Configure NVMe/FC with Broadcom/Emulex or Marvell/QLogic adapters, or configure NVMe/TCP using manual discovery and connect operations.

FC - Broadcom/Emulex

Configure NVMe/FC for a Broadcom/Emulex adapter.

Steps

Verify that you are using the supported adapter model:

Display the model names:

cat /sys/class/scsi_host/host*/modelname

You should see the following output:

LPe36002-M64
LPe36002-M64

Display the model descriptions:

cat /sys/class/scsi_host/host*/modeldesc

You should see output similar to the following example:

Emulex LightPulse LPe36002-M64 2-Port 64Gb Fibre Channel Adapter
Emulex LightPulse LPe36002-M64 2-Port 64Gb Fibre Channel Adapter

Verify that you are using the recommended Broadcom lpfc firmware and inbox driver:
1. Display the firmware version:
  cat /sys/class/scsi_host/host*/fwrev
  The command returns the firmware versions:
  14.0.539.16, sli-4:6:d 14.0.539.16, sli-4:6:d
2. Display the inbox driver version:
  cat /sys/module/lpfc/version
  The following example shows a driver version:
  0:14.4.0.6
For the current list of supported adapter driver and firmware versions, see the Interoperability Matrix Tool.

Verify that lpfc_enable_fc4_type is set to 3:

cat /sys/module/lpfc/parameters/lpfc_enable_fc4_type

Verify that you can view your initiator ports:
```
cat /sys/class/fc_host/host*/port_name
```
You should see output similar to:
```
0x100000109b1c1205
```
Verify that your initiator ports are online:
```
cat /sys/class/fc_host/host*/port_state
```
You should see the following output:
```
Online
Online
```

Verify that the NVMe/FC initiator ports are enabled and that the target ports are visible:

cat /sys/class/scsi_host/host*/nvme_info

Show example

NVME Initiator Enabled
XRI Dist lpfc2 Total 6144 IO 5894 ELS 250
NVME LPORT lpfc2 WWPN x100000109bf044b1 WWNN x200000109bf044b1 DID x022a00 ONLINE
NVME RPORT       WWPN x202fd039eaa7dfc8 WWNN x202cd039eaa7dfc8 DID x021310 TARGET DISCSRVC ONLINE
NVME RPORT       WWPN x202dd039eaa7dfc8 WWNN x202cd039eaa7dfc8 DID x020b10 TARGET DISCSRVC ONLINE

NVME Statistics
LS: Xmt 0000000810 Cmpl 0000000810 Abort 00000000
LS XMIT: Err 00000000  CMPL: xb 00000000 Err 00000000
Total FCP Cmpl 000000007b098f07 Issue 000000007aee27c4 OutIO ffffffffffe498bd
        abort 000013b4 noxri 00000000 nondlp 00000058 qdepth 00000000 wqerr 00000000 err 00000000
FCP CMPL: xb 000013b4 Err 00021443

NVME Initiator Enabled
XRI Dist lpfc3 Total 6144 IO 5894 ELS 250
NVME LPORT lpfc3 WWPN x100000109bf044b2 WWNN x200000109bf044b2 DID x021b00 ONLINE
NVME RPORT       WWPN x2033d039eaa7dfc8 WWNN x202cd039eaa7dfc8 DID x020110 TARGET DISCSRVC ONLINE
NVME RPORT       WWPN x2032d039eaa7dfc8 WWNN x202cd039eaa7dfc8 DID x022910 TARGET DISCSRVC ONLINE

NVME Statistics
LS: Xmt 0000000840 Cmpl 0000000840 Abort 00000000
LS XMIT: Err 00000000  CMPL: xb 00000000 Err 00000000
Total FCP Cmpl 000000007afd4434 Issue 000000007ae31b83 OutIO ffffffffffe5d74f
        abort 000014a5 noxri 00000000 nondlp 0000006a qdepth 00000000 wqerr 00000000 err 00000000
FCP CMPL: xb 000014a5 Err 0002149a

FC - Marvell/QLogic

Configure NVMe/FC for a Marvell/QLogic adapter.

Steps

Verify that you are using the supported adapter driver and firmware versions:
```
cat /sys/class/fc_host/host*/symbolic_name
```
The following example shows driver and firmware versions:
```
QLE2872 FW:v9.15.00 DVR:v10.02.09.300-k
QLE2872 FW:v9.15.00 DVR:v10.02.09.300-k
```
Verify that ql2xnvmeenable is set. This enables the Marvell adapter to function as an NVMe/FC initiator:
```
cat /sys/module/qla2xxx/parameters/ql2xnvmeenable
```
The expected output is 1.

TCP

The NVMe/TCP protocol doesn't support the auto-connect operation. Instead, you can discover the NVMe/TCP subsystems and namespaces by performing the NVMe/TCP connect or connect-all operations manually.

Steps

Check that the initiator port can get the discovery log page data across the supported NVMe/TCP LIFs:

nvme discover -t tcp -w host-traddr -a traddr

Show example

nvme discover -t tcp -w 192.168.20.1 -a 192.168.20.20

Discovery Log Number of Records 8, Generation counter 18
=====Discovery Log Entry 0======
trtype:  tcp
adrfam:  ipv4
subtype: current discovery subsystem
treq:    not specified
portid:  4
trsvcid: 8009
subnqn:  nqn.1992-08.com.netapp:sn.64e65e6caae711ef9668d039ea951c46:discovery
traddr:  192.168.21.21
eflags:  explicit discovery connections, duplicate discovery information
sectype: none
=====Discovery Log Entry 1======
trtype:  tcp
adrfam:  ipv4
subtype: current discovery subsystem
treq:    not specified
portid:  2
trsvcid: 8009
subnqn:  nqn.1992-08.com.netapp:sn.64e65e6caae711ef9668d039ea951c46:discovery
traddr:  192.168.20.21
eflags:  explicit discovery connections, duplicate discovery information
sectype: none
=====Discovery Log Entry 2======
trtype:  tcp
adrfam:  ipv4
subtype: current discovery subsystem
treq:    not specified
portid:  3
trsvcid: 8009
subnqn:  nqn.1992-08.com.netapp:sn.64e65e6caae711ef9668d039ea951c46:discovery
traddr:  192.168.21.20
eflags:  explicit discovery connections, duplicate discovery information
sectype: none
=====Discovery Log Entry 3======
trtype:  tcp
adrfam:  ipv4
subtype: current discovery subsystem
treq:    not specified
portid:  1
trsvcid: 8009
subnqn:  nqn.1992-08.com.netapp:sn.64e65e6caae711ef9668d039ea951c46:discovery
traddr:  192.168.20.20
eflags:  explicit discovery connections, duplicate discovery information
sectype: none
=====Discovery Log Entry 4======
trtype:  tcp
adrfam:  ipv4
subtype: nvme subsystem
treq:    not specified
portid:  4
trsvcid: 4420
subnqn:  nqn.1992-08.com.netapp:sn.64e65e6caae711ef9668d039ea951c46:subsystem.rhel10_tcp_subsystem
traddr:  192.168.21.21
eflags:  none
sectype: none
=====Discovery Log Entry 5======
trtype:  tcp
adrfam:  ipv4
subtype: nvme subsystem
treq:    not specified
portid:  2
trsvcid: 4420
subnqn:  nqn.1992-08.com.netapp:sn.64e65e6caae711ef9668d039ea951c46:subsystem.rhel10_tcp_subsystem
traddr:  192.168.20.21
eflags:  none
sectype: none
=====Discovery Log Entry 6======
trtype:  tcp
adrfam:  ipv4
subtype: nvme subsystem
treq:    not specified
portid:  3
trsvcid: 4420
subnqn:  nqn.1992-08.com.netapp:sn.64e65e6caae711ef9668d039ea951c46:subsystem.rhel10_tcp_subsystem
traddr:  192.168.21.20
eflags:  none
sectype: none
=====Discovery Log Entry 7======
trtype:  tcp
adrfam:  ipv4
subtype: nvme subsystem
treq:    not specified
portid:  1
trsvcid: 4420
subnqn:  nqn.1992-08.com.netapp:sn.64e65e6caae711ef9668d039ea951c46:subsystem.rhel10_tcp_subsystem
traddr:  192.168.20.20
eflags:  none
sectype: none

Verify that the other NVMe/TCP initiator-target LIF combinations can successfully retrieve discovery log page data:

nvme discover -t tcp -w host-traddr -a traddr

Show example

nvme discover -t tcp -w 192.168.20.1 -a 192.168.20.20
nvme discover -t tcp -w 192.168.21.1 -a 192.168.21.20
nvme discover -t tcp -w 192.168.20.1 -a 192.168.20.21
nvme discover -t tcp -w 192.168.21.1 -a 192.168.21.21

Run the nvme connect-all command across all the supported NVMe/TCP initiator-target LIFs across the nodes:

nvme connect-all -t tcp -w host-traddr -a traddr

Show example

nvme	connect-all	-t	tcp	-w	192.168.20.1	-a	192.168.20.20
nvme	connect-all	-t	tcp	-w	192.168.21.1	-a	192.168.21.20
nvme	connect-all	-t	tcp	-w	192.168.20.1	-a	192.168.20.21
nvme	connect-all	-t	tcp	-w	192.168.21.1	-a	192.168.21.21

Beginning with RHEL 9.4, the setting for the NVMe/TCP ctrl_loss_tmo timeout is automatically set to "off". As a result:

There are no limits on the number of retries (indefinite retry).
You don't need to manually configure a specific ctrl_loss_tmo timeout duration when using the nvme connect or nvme connect-all commands (option -l ).
The NVMe/TCP controllers don't experience timeouts in the event of a path failure and remain connected indefinitely.

Step 4: Optionally, enable 1MB I/O for NVMe/FC

ONTAP reports a Max Data Transfer Size (MDTS) of 8 in the Identify Controller data. This means the maximum I/O request size can be up to 1MB. To issue I/O requests of size 1MB for a Broadcom NVMe/FC host, you should increase the lpfc value of the lpfc_sg_seg_cnt parameter to 256 from the default value of 64.

These steps don't apply to Qlogic NVMe/FC hosts.

Steps

Set the lpfc_sg_seg_cnt parameter to 256:
```
cat /etc/modprobe.d/lpfc.conf
```
You should see an output similar to the following example:
```
options lpfc lpfc_sg_seg_cnt=256
```
Run the dracut -f command, and reboot the host.

Verify that the value for lpfc_sg_seg_cnt is 256:

cat /sys/module/lpfc/parameters/lpfc_sg_seg_cnt

Step 5: Verify NVMe boot services

The nvmefc-boot-connections.service and nvmf-autoconnect.service boot services included in the NVMe/FC nvme-cli package are automatically enabled when the system boots.

After booting completes, verify that the nvmefc-boot-connections.service and nvmf-autoconnect.service boot services are enabled.

Steps

Verify that nvmf-autoconnect.service is enabled:

systemctl status nvmf-autoconnect.service

Show example output

nvmf-autoconnect.service - Connect NVMe-oF subsystems automatically during boot
     Loaded: loaded (/usr/lib/systemd/system/nvmf-autoconnect.service; enabled; preset: disabled)
     Active: inactive (dead)

Jun 10 04:06:26 SR630-13-201.lab.eng.btc.netapp.in systemd[1]: Starting Connect NVMe-oF subsystems automatically during boot...
Jun 10 04:06:26 SR630-13-201.lab.eng.btc.netapp.in systemd[1]: nvmf-autoconnect.service: Deactivated successfully.
Jun 10 04:06:26 SR630-13-201.lab.eng.btc.netapp.in systemd[1]: Finished Connect NVMe-oF subsystems automatically during boot.

Verify that nvmefc-boot-connections.service is enabled:

systemctl status nvmefc-boot-connections.service

Show example output

nvmefc-boot-connections.service - Auto-connect to subsystems on FC-NVME devices found during boot
     Loaded: loaded (/usr/lib/systemd/system/nvmefc-boot-connections.service; enabled; preset: enabled)
     Active: inactive (dead) since Tue 2025-06-10 01:08:36 EDT; 2h 59min ago
   Main PID: 7090 (code=exited, status=0/SUCCESS)
        CPU: 30ms

Jun 10 01:08:36 localhost systemd[1]: Starting Auto-connect to subsystems on FC-NVME devices found during boot...
Jun 10 01:08:36 localhost systemd[1]: nvmefc-boot-connections.service: Deactivated successfully.
Jun 10 01:08:36 localhost systemd[1]: Finished Auto-connect to subsystems on FC-NVME devices found during boot.

Step 6: Verify the multipathing configuration

Verify that the in-kernel NVMe multipath status, ANA status, and ONTAP namespaces are correct for the NVMe-oF configuration.

Steps

Verify that the in-kernel NVMe multipath is enabled:
```
cat /sys/module/nvme_core/parameters/multipath
```
You should see the following output:
```
Y
```
Verify that the appropriate NVMe-oF settings (such as, model set to NetApp ONTAP Controller and load balancing iopolicy set to round-robin) for the respective ONTAP namespaces correctly reflect on the host:
1. Display the subsystems:
  cat /sys/class/nvme-subsystem/nvme-subsys*/model
  You should see the following output:
  NetApp ONTAP Controller NetApp ONTAP Controller
2. Display the policy:
  cat /sys/class/nvme-subsystem/nvme-subsys*/iopolicy
  You should see the following output:
  round-robin round-robin

Verify that the namespaces are created and correctly discovered on the host:

nvme list

Show example

Node         SN                   Model
---------------------------------------------------------
/dev/nvme4n1 81Ix2BVuekWcAAAAAAAB	NetApp ONTAP Controller


Namespace Usage    Format             FW             Rev
-----------------------------------------------------------
1                 21.47 GB / 21.47 GB	4 KiB + 0 B   FFFFFFFF

Verify that the controller state of each path is live and has the correct ANA status:

NVMe/FC

nvme list-subsys /dev/nvme5n1

Show example

nvme-subsys5 - NQN=nqn.1992-08.com.netapp:sn.f7565b15a66911ef9668d039ea951c46:subsystem.nvme1
               hostnqn=nqn.2014-08.org.nvmexpress:uuid:4c4c4544-0056-5410-8048-c7c04f425633
\
 +- nvme126 fc traddr=nn-0x2036d039ea951c45:pn-0x2038d039ea951c45,host_traddr=nn-0x2000f4c7aa0cd7c3:pn-0x2100f4c7aa0cd7c3 live optimized
 +- nvme176 fc traddr=nn-0x2036d039ea951c45:pn-0x2037d039ea951c45,host_traddr=nn-0x2000f4c7aa0cd7c2:pn-0x2100f4c7aa0cd7c2 live optimized
 +- nvme5 fc traddr=nn-0x2036d039ea951c45:pn-0x2039d039ea951c45,host_traddr=nn-0x2000f4c7aa0cd7c2:pn-0x2100f4c7aa0cd7c2 live non-optimized
 +- nvme71 fc traddr=nn-0x2036d039ea951c45:pn-0x203ad039ea951c45,host_traddr=nn-0x2000f4c7aa0cd7c3:pn-0x2100f4c7aa0cd7c3 live non-optimized

NVMe/TCP

nvme list-subsys /dev/nvme4n2

Show example

nvme-subsys4 - NQN=nqn.1992-08.com.netapp:sn.64e65e6caae711ef9668d039ea951c46:subsystem.nvme4
               hostnqn=nqn.2014-08.org.nvmexpress:uuid:4c4c4544-0035-5910-804b-c2c04f444d33
\
+- nvme102 tcp traddr=192.168.21.20,trsvcid=4420,host_traddr=192.168.21.1,src_addr=192.168.21.1 live non-optimized
+- nvme151 tcp traddr=192.168.21.21,trsvcid=4420,host_traddr=192.168.21.1,src_addr=192.168.21.1 live optimized
+- nvme4 tcp traddr=192.168.20.20,trsvcid=4420,host_traddr=192.168.20.1,src_addr=192.168.20.1 live non-optimized
+- nvme53 tcp traddr=192.168.20.21,trsvcid=4420,host_traddr=192.168.20.1,src_addr=192.168.20.1 live optimized

Verify that the NetApp plug-in displays the correct values for each ONTAP namespace device:

Column

nvme netapp ontapdevices -o column

Show example

Device        Vserver   Namespace Path
----------------------- ------------------------------
/dev/nvme10n1     vs_tcp_rhel10       /vol/vol10/ns10

NSID       UUID                                   Size
----------------------- ------------------------------
1    bbf51146-fc64-4197-b8cf-8a24f6f359b3   21.47GB

JSON

nvme netapp ontapdevices -o json

Show example

{
  "ONTAPdevices":[
    {
      "Device":"/dev/nvme10n1",
      "Vserver":"vs_tcp_rhel10",
      "Namespace_Path":"/vol/vol10/ns10",
      "NSID":1,
      "UUID":"bbf51146-fc64-4197-b8cf-8a24f6f359b3",
      "Size":"21.47GB",
      "LBA_Data_Size":4096,
      "Namespace_Size":5242880
}
]
    }

Step 7: Set up secure in-band authentication

Beginning with ONTAP 9.12.1, secure in-band authentication is supported over NVMe/TCP between a RHEL 10.0 host and an ONTAP controller.

Each host or controller must be associated with a DH-HMAC-CHAP key to set up secure authentication. A DH-HMAC-CHAP key is a combination of the NQN of the NVMe host or controller and an authentication secret configured by the administrator. To authenticate its peer, an NVMe host or controller must recognize the key associated with the peer.

Set up secure in-band authentication using the CLI or a config JSON file. If you need to specify different dhchap keys for different subsystems, you must use a config JSON file.

CLI

Set up secure in-band authentication using the CLI.

Steps

Obtain the host NQN:
```
cat /etc/nvme/hostnqn
```

Generate the dhchap key for the RHEL 10.0 host.

The following output describes the gen-dhchap-key command parameters:

nvme gen-dhchap-key -s optional_secret -l key_length {32|48|64} -m HMAC_function {0|1|2|3} -n host_nqn
•	-s secret key in hexadecimal characters to be used to initialize the host key
•	-l length of the resulting key in bytes
•	-m HMAC function to use for key transformation
0 = none, 1- SHA-256, 2 = SHA-384, 3=SHA-512
•	-n host NQN to use for key transformation

In the following example, a random dhchap key with HMAC set to 3 (SHA-512) is generated.

nvme gen-dhchap-key -m 3 -n nqn.2014-08.org.nvmexpress:uuid:4c4c4544-0035-5910-804b-c2c04f444d33
DHHC-1:03:7zf8I9gaRcDWH3tCH5vLGaoyjzPIvwNWusBfKdpJa+hia1aKDKJQ2o53pX3wYM9xdv5DtKNNhJInZ7X8wU2RQpQIngc=:

On the ONTAP controller, add the host and specify both dhchap keys:

vserver nvme subsystem host add -vserver <svm_name> -subsystem <subsystem> -host-nqn <host_nqn> -dhchap-host-secret <authentication_host_secret> -dhchap-controller-secret <authentication_controller_secret> -dhchap-hash-function {sha-256|sha-512} -dhchap-group {none|2048-bit|3072-bit|4096-bit|6144-bit|8192-bit}

A host supports two types of authentication methods, unidirectional and bidirectional. On the host, connect to the ONTAP controller and specify dhchap keys based on the chosen authentication method:
```
nvme connect -t tcp -w <host-traddr> -a <tr-addr> -n <host_nqn> -S <authentication_host_secret> -C <authentication_controller_secret>
```

Validate the nvme connect authentication command by verifying the host and controller dhchap keys:

Verify the host dhchap keys:

cat /sys/class/nvme-subsystem/<nvme-subsysX>/nvme*/dhchap_secret

Show example output for a unidirectional configuration

cat /sys/class/nvme-subsystem/nvme-subsys1/nvme*/dhchap_secret
DHHC- 1:03:fMCrJharXUOqRoIsOEaG6m2PH1yYvu5+z3jTmzEKUbcWu26I33b93b
il2WR09XDho/ld3L45J+0FeCsStBEAfhYgkQU=:
DHHC- 1:03:fMCrJharXUOqRoIsOEaG6m2PH1yYvu5+z3jTmzEKUbcWu26I33b93b
il2WR09XDho/ld3L45J+0FeCsStBEAfhYgkQU=:
DHHC- 1:03:fMCrJharXUOqRoIsOEaG6m2PH1yYvu5+z3jTmzEKUbcWu26I33b93b
il2WR09XDho/ld3L45J+0FeCsStBEAfhYgkQU=:
DHHC- 1:03:fMCrJharXUOqRoIsOEaG6m2PH1yYvu5+z3jTmzEKUbcWu26I33b93b
il2WR09XDho/ld3L45J+0FeCsStBEAfhYgkQU=:

Verify the controller dhchap keys:

cat /sys/class/nvme-subsystem/<nvme-subsysX>/nvme*/dhchap_ctrl_secret

Show example output for a bidirectional configuration

cat /sys/class/nvme-subsystem/nvme-subsys6/nvme*/dhchap_ctrl_secret
DHHC- 1:03:7zf8I9gaRcDWH3tCH5vLGaoyjzPIvwNWusBfKdpJa+hia
1aKDKJQ2o53pX3wYM9xdv5DtKNNhJInZ7X8wU2RQpQIngc=:

DHHC- 1:03:7zf8I9gaRcDWH3tCH5vLGaoyjzPIvwNWusBfKdpJa+hia
1aKDKJQ2o53pX3wYM9xdv5DtKNNhJInZ7X8wU2RQpQIngc=:

DHHC- 1:03:7zf8I9gaRcDWH3tCH5vLGaoyjzPIvwNWusBfKdpJa+hia
1aKDKJQ2o53pX3wYM9xdv5DtKNNhJInZ7X8wU2RQpQIngc=:

DHHC- 1:03:7zf8I9gaRcDWH3tCH5vLGaoyjzPIvwNWusBfKdpJa+hia
1aKDKJQ2o53pX3wYM9xdv5DtKNNhJInZ7X8wU2RQpQIngc=:

JSON

When multiple NVMe subsystems are available on the ONTAP controller, you can use the /etc/nvme/config.json file with the nvme connect-all command.

Use the -o option to generate the JSON file. Refer to the NVMe connect-all man pages for more syntax options.

Steps

Configure the JSON file.

In the following example, dhchap_key corresponds to dhchap_secret and dhchap_ctrl_key corresponds to dhchap_ctrl_secret.

Show example

cat /etc/nvme/config.json
[
{
"hostnqn":"nqn.2014-08.org.nvmexpress:uuid:4c4c4544-0035-5910-804b-c2c04f444d33",
"hostid":"4c4c4544-0035-5910-804b-c2c04f444d33",
"dhchap_key":"DHHC-1:03:7zf8I9gaRcDWH3tCH5vLGaoyjzPIvwNWusBfKdpJa+hia1aKDKJQ2o53pX3wYM9xdv5DtKNNhJInZ7X8wU2RQpQIngc=:",
"subsystems":[
{
"nqn":"nqn.1992-08.com.netapp:sn.127ade26168811f0a50ed039eab69ad3:subsystem.inband_unidirectional",
"ports":[
{
"transport":"tcp",
"traddr":"192.168.20.17",
"host_traddr":"192.168.20.1",
"trsvcid":"4420"
},
{
"transport":"tcp",
"traddr":"192.168.20.18",
"host_traddr":"192.168.20.1",
"trsvcid":"4420"
},
{
"transport":"tcp",
"traddr":"192.168.21.18",
"host_traddr":"192.168.21.1",
"trsvcid":"4420"
},
{
"transport":"tcp",
"traddr":"192.168.21.17",
"host_traddr":"192.168.21.1",
"trsvcid":"4420"
}]

Connect to the ONTAP controller using the config JSON file:

nvme connect-all -J /etc/nvme/config.json

Show example

traddr=192.168.20.20 is already connected
traddr=192.168.20.20 is already connected
traddr=192.168.20.20 is already connected
traddr=192.168.20.20 is already connected
traddr=192.168.20.20 is already connected
traddr=192.168.20.20 is already connected
traddr=192.168.20.20 is already connected
traddr=192.168.20.20 is already connected
traddr=192.168.20.21 is already connected
traddr=192.168.20.21 is already connected
traddr=192.168.20.21 is already connected
traddr=192.168.20.21 is already connected
traddr=192.168.20.21 is already connected
traddr=192.168.20.21 is already connected
traddr=192.168.20.21 is already connected
traddr=192.168.20.21 is already connected

Verify that the dhchap secrets have been enabled for the respective controllers for each subsystem.

Verify the host dhchap keys:

cat /sys/class/nvme-subsystem/nvme-subsys0/nvme0/dhchap_secret

The following example shows a dhchap key:

DHHC-1:03:7zf8I9gaRcDWH3tCH5vLGaoyjzPIvwNWusBfKdpJa+hia1
aKDKJQ2o53pX3wYM9xdv5DtKNNhJInZ7X8wU2RQpQIngc=:

Verify the controller dhchap keys:

cat /sys/class/nvme-subsystem/nvme-subsys0/nvme0/dhchap_ctrl_secret

You should see output similar to the following example:

DHHC-1:03:fMCrJharXUOqRoIsOEaG6m2PH1yYvu5+z3jT
mzEKUbcWu26I33b93bil2WR09XDho/ld3L45J+0FeCsStBEAfhYgkQU=:

Step 8: Review the known issues

There are no known issues.

Configure RHEL 10.0 for NVMe-oF with ONTAP storage

Creating your file...

Step 1: Optionally, enable SAN booting

Step 2: Verify the software version and NVMe configuration

Step 3: Configure NVMe/FC and NVMe/TCP

Step 4: Optionally, enable 1MB I/O for NVMe/FC

Step 5: Verify NVMe boot services

Step 6: Verify the multipathing configuration

Step 7: Set up secure in-band authentication

Step 8: Review the known issues