Skip to main content
StorageGRID Appliances

Appliance node cloning: Overview

Contributors netapp-perveilerk
PDFs

You can clone an appliance node in StorageGRID to use an appliance of newer design or increased capabilities. Cloning transfers all information about the existing node to the new appliance, provides a hardware-upgrade process that is easy to perform, and provides an alternative to decommissioning and expansion for replacing appliances.

Appliance node cloning lets you easily replace an existing appliance node (source) in your grid with a compatible appliance (target) that is part of the same logical StorageGRID site. The process transfers all data to the new appliance, placing it in service to replace the old appliance node and leaving the old appliance in a pre-install state.

Why clone an appliance node?

You can clone an appliance node if you need to:

  • Replace appliances that are reaching end-of-life.

  • Upgrade existing nodes to take advantage of improved appliance technology.

  • Increase grid storage capacity without changing the number of Storage Nodes in your StorageGRID system.

  • Improve storage efficiency, such as by changing the RAID mode from DDP-8 to DDP-16, or to RAID-6.

  • Efficiently implement node encryption to allow the use of external key management servers (KMS).

Which StorageGRID network is used?

Cloning transfers data from the source node directly to the target appliance over any of the three StorageGRID networks. The Grid Network is typically used, but you can also use the Admin Network or the Client Network if the source appliance is connected to these networks. Choose the network to use for cloning traffic that provides the best data-transfer performance without degrading StorageGRID network performance or data availability.

When you install the replacement appliance, you must specify temporary IP addresses for StorageGRID connection and data transfer. Because the replacement appliance will be part of the same networks as the appliance node it replaces, you must specify temporary IP addresses for each of these networks on the replacement appliance.

What information is not cloned?

The following appliance configurations don't transfer to the replacement appliance during cloning. You must configure them during initial setup of the replacement appliance.

  • BMC interface

  • Network links

  • Node encryption status

  • SANtricity System Manager (for Storage Nodes)

  • RAID mode (for Storage Nodes)

What issues prevent cloning?

If any of the following issues are encountered while cloning, the cloning process halts and an error message is generated:

  • Wrong network configuration

  • Lack of connectivity between the source and target appliances

  • Source and target appliance incompatibility

  • For Storage Nodes, a replacement appliance of insufficient capacity

You must resolve each issue for cloning to continue.

Target appliance compatibility

Replacement appliances must be the same type as the source node they are replacing and both must be part of the same logical StorageGRID site.

Review the general cloning considerations and specific cloning information and restrictions for each appliance type before cloning.

General services appliance cloning considerations

  • A replacement services appliance can be a different model than the Admin Node or Gateway Node it is replacing.

  • The services appliances have different network connectors. Changing the appliance type might require replacing the cables or SFP modules.

General storage appliance cloning considerations

  • A replacement storage appliance must have greater capacity than the Storage Node it is replacing.

    • If the target storage appliance has the same number of drives as the source node, the drives in the target appliance must have greater capacity (in TB).

    • If you plan to use the same RAID mode on the target node as was used on the source node, or a less storage efficient RAID mode (for example, switching from RAID 6 to DDP), the drives in the target appliance must be larger (in TB) than the drives in the source appliance.

    • Exceptions to the general storage appliance cloning considerations include:

      • If the number of standard drives installed in a target storage appliance is less than the number of drives in the source node, due to installation of solid-state drives (SSDs), the overall storage capacity of the standard drives in the target appliance (in TB) must exceed the total functional drive capacity of all drives in the source Storage Node.

        For example, when cloning an SG5760 source Storage Node appliance with 60 drives to an SG6060 target appliance with 58 standard drives, larger drives should be installed in the SG6060 target appliance before cloning to maintain storage capacity. (The two drive slots containing SSDs in the target appliance aren't included in the total appliance-storage capacity.)

        However, if a 60-drive SG5760 source node appliance is configured with SANtricity Dynamic Disk Pools DDP-8 (DDP), configuring a 58-drive same-size-drive SG6060 target appliance with DDP-16 might make the SG6060 appliance a valid clone target due to its improved storage efficiency.

        You can view information about the current RAID mode of the source appliance node on the NODES page in Grid Manager. Select the Storage tab for the appliance.

      • The number of volumes in a target storage appliance must be greater than or equal to the number of volumes in the source node. You cannot clone a source node with 16 object store volumes (rangedb) to a target storage appliance with 12 object store volumes even if the target appliance has larger capacity than the source node. Most storage appliances have 16 object store volumes, except the SGF6112 storage appliance that has only 12 object store volumes.

SG100 appliance cloning information and restrictions

You can clone an SG100 source node appliance to an SG110, SG1000, or SG1100 services target appliance. Cloning the SG100 to an SG1000 or SG1100 services target appliance gives the Admin Node or Gateway Node greater capability.

SG110 appliance cloning information and restrictions

You can clone an SG110 source node appliance to an SG1100 services appliance target to give the Admin Node or Gateway Node greater capability.

SG1000 appliance cloning information and restrictions

You can clone an SG1000 source node appliance to an SG100, SG110, or SG1100 services target appliance.

  • Cloning the SG1000 to an SG100 or SG110 services target appliance lets you redeploy the SG1000 for a more demanding application.

  • Replacing an SG1000 source node appliance with an SG100 services target appliance reduces the maximum speed of the network ports from 100-GbE to 25-GbE.

SG1100 appliance cloning information and restrictions

You can clone an SG1100 source node appliance to an SG110 services target appliance.

  • Cloning the SG1100 to an SG110 services target appliance lets you redeploy the SG1100 for a more demanding application. For example, if an SG1100 source node appliance is being used as an Admin Node and you want to use it as a dedicated load-balancing node.

  • Replacing an SG1100 source node appliance with an SG110 services target appliance reduces the maximum speed of the network ports from 100-GbE to 25-GbE.

SG5712 appliance cloning information and restrictions

You can clone an SG5712 source node appliance configured with DDP to an SG5812 storage target appliance.

SG5760 appliance cloning information and restrictions

  • You can clone an SG5760 source node appliance configured with DDP16 to an SG5860 storage target appliance configured with DDP16.

  • An SG5760 source node appliance configured with DDP cannot be cloned to an SG5860 storage target appliance configured with DDP.

  • An SG5760 source node appliance configured with DDP or DDP-16 cannot be cloned to an SG6160 storage target appliance with a matching RAID mode.

SG5812 appliance cloning information and restrictions

You can successfully clone an SG5812 appliance as the source or the target.

SG5860 appliance cloning information and restrictions

You can successfully clone an SG5860 appliance as the source or the target with some restrictions (listed in the appliance cloning information and restrictions for each source).

SG6060 appliance cloning information and restrictions

  • You can clone an SG6060 source node appliance configured with DDP or DDP16 to an SG5860 storage target appliance with a matching RAID mode.

  • You can clone an SG6060 source node appliance without any expansion shelves to an SG6160 storage target appliance without any expansion shelves if the drive sizes and RAID modes are the same.

  • An SG6060 source node appliance with any number of expansion shelves cannot be cloned to an SG6160 storage target appliance even if the number of expansion shelves, drive sizes, and RAID modes are the same.

SG6160 appliance cloning information and restrictions

You can successfully clone an SG6160 appliance as the source or the target with some restrictions (listed in the appliance cloning information and restrictions for each source).