Skip to main content
ONTAP MetroCluster
简体中文版经机器翻译而成，仅供参考。如与英语版出现任何冲突，应以英语版为准。

修改MetroCluster IP接口的属性

贡献者
PDF

从 ONTAP 9.10.1 开始，您可以更改 MetroCluster IP 接口的以下属性： IP 地址和掩码以及网关。您可以使用任意参数组合进行更新。

您可能需要更新这些属性，例如，如果检测到重复的 IP 地址，或者在第 3 层网络中，如果由于路由器配置更改而需要更改网关。

修改 IP 地址，网络掩码和网关

您遵循的过程取决于您使用的是ONTAP系统管理器还是命令行界面。

System Manager

使用System Manager修改IP地址、网络掩码和网关属性。

步骤

更新每个节点和接口的IP地址、网络掩码和网关。

命令行界面

使用命令行界面修改IP地址、网络掩码和网关属性。

关于此任务

  • 一次只能更改一个接口。在更新其他接口并重新建立连接之前，此接口上的流量将中断。

  • 使用 MetroCluster configuration-settings interface modify 命令更改任何 MetroCluster IP 接口属性。

    备注 这些命令用于更改特定端口的特定节点上的配置。要还原完整的网络连接，需要在其他端口上使用类似的命令。同样，网络交换机也需要更新其配置。例如，如果网关已更新，则理想情况下，它会在 HA 对的两个节点上进行更改，因为它们是相同的。连接到这些节点的交换机还需要更新其网关。

  • 使用 metrocluster configuration-settings interface show、 metrocluster connection check`和 `metrocluster connection show 命令验证所有连接在所有接口上均正常工作。

步骤

  1. 更新单个节点和接口的 IP 地址，网络掩码和网关： MetroCluster configuration-settings interface modify

    以下命令显示如何更新 IP 地址，网络掩码和网关：

    cluster_A::* metrocluster configuration-settings interface modify -cluster-name cluster_A -home-node node_A_1 -home-port e0a-10 -address 192.168.12.101 -gateway 192.168.12.1 -netmask 255.255.254.0
(metrocluster configuration-settings interface modify)
Warning: This operation will disconnect and reconnect iSCSI and RDMA connections used for DR protection through port “e0a-10”. Partner nodes may need modifications for port “e0a-10” in order to completely establish network connectivity.
Do you want to continue?" yes
[Job 28] Setting up iSCSI target configuration. (pass2:iscsi13:0:-1:0): xpt_action_default: CCB type 0xe XPT_DEV_ADVINFO not supported
[Job 28] Establishing iSCSI initiator connections.
(pass6:iscsi14:0:-1:0): xpt_action_default: CCB type 0xe XPT_DEV_ADVINFO not supported
(pass8:iscsi15:0:-1:0): xpt_action_default: CCB type 0xe XPT_DEV_ADVINFO not supported
(pass9:iscsi16:0:-1:0): xpt_action_default: CCB type 0xe XPT_DEV_ADVINFO not supported
[Job 28] Job succeeded: Interface Modify is successful.
cluster_A::*> metrocluster configuration-settings interface modify -cluster-name cluster_A -home-node node_A_2 -home-port e0a-10 -address 192.168.12.201 -gateway 192.168.12.1 -netmask 255.255.254.0
(metrocluster configuration-settings interface modify)
Warning: This operation will disconnect and reconnect iSCSI and RDMA connections used for DR protection through port “e0a-10”. Partner nodes may need modifications for port “e0a-10” in order to completely establish network connectivity.
Do you want to continue?" yes
[Job 28] Job succeeded: Interface Modify is successful

  2. 【第 2 步】验证所有接口的所有连接是否正常工作： MetroCluster configuration-settings interface show

    以下命令显示如何验证所有接口的所有连接是否正常工作：

    cluster_A::*> metrocluster configuration-settings interface show
(metrocluster configuration-settings interface show)                                                 DR              Config
Group Cluster Node    Network Address Netmask         Gateway         State
----- ------- ------- --------------- --------------- --------------- ---------
1     cluster_A node_A_2
                 Home Port: e0a-10
                      192.168.12.201  255.255.254.0   192.168.12.1    completed
                 Home Port: e0b-20
                      192.168.20.200  255.255.255.0   192.168.20.1    completed
                node_A_1
                 Home Port: e0a-10
                      192.168.12.101  255.255.254.0   192.168.12.1    completed
                 Home Port: e0b-20
                      192.168.20.101  255.255.255.0   192.168.20.1    completed
      cluster_B node_B_1
                 Home Port: e0a-10
                      192.168.11.151  255.255.255.0   192.168.11.1    completed
                 Home Port: e0b-20
                      192.168.21.150  255.255.255.0   192.168.21.1    completed
                node_B_2
                 Home Port: e0a-10
                      192.168.11.250  255.255.255.0   192.168.11.1    completed
                 Home Port: e0b-20
                      192.168.21.250  255.255.255.0   192.168.21.1    completed
8 entries were displayed.

  3. 验证所有连接是否均正常工作：

    MetroCluster configuration-settings connection show

    以下命令显示如何验证所有连接是否正常工作：

    cluster_A::*> metrocluster configuration-settings connection show
  (metrocluster configuration-settings connection show)
DR                    Source          Destination
Group Cluster Node    Network Address Network Address Partner Type Config State
----- ------- ------- --------------- --------------- ------------ ------------
1     cluster_A node_A_2
                 Home Port: e0a-10
                      192.168.10.200  192.168.10.101  HA Partner   completed
                 Home Port: e0a-10
                      192.168.10.200  192.168.11.250  DR Partner   completed
                 Home Port: e0a-10
                      192.168.10.200  192.168.11.151  DR Auxiliary completed
                 Home Port: e0b-20
                      192.168.20.200  192.168.20.100  HA Partner   completed
                 Home Port: e0b-20
                      192.168.20.200  192.168.21.250  DR Partner   completed
                 Home Port: e0b-20
                      192.168.20.200  192.168.21.150  DR Auxiliary completed
                node_A_1
                 Home Port: e0a-10
                      192.168.10.101  192.168.10.200  HA Partner   completed
                 Home Port: e0a-10
                      192.168.10.101  192.168.11.151  DR Partner   completed
                 Home Port: e0a-10
                      192.168.10.101  192.168.11.250  DR Auxiliary completed
                 Home Port: e0b-20
                      192.168.20.100  192.168.20.200  HA Partner   completed
                 Home Port: e0b-20
                      192.168.20.100  192.168.21.150  DR Partner   completed
                 Home Port: e0b-20
                      192.168.20.100  192.168.21.250  DR Auxiliary completed