简体中文版经机器翻译而成,仅供参考。如与英语版出现任何冲突,应以英语版为准。

编辑参考配置文件( RCF )— BES-53248 交换机

提供者 netapp-martyh netapp-yvonneo

要激活新许可的端口,您需要编辑最新版本的 RCF 并取消注释适用的端口详细信息。默认许可证会激活端口 0/1 到 0/16 以及从 0/55 到 0/56 ,而新许可的端口将位于端口 0/17 到 0/54 之间,具体取决于可用许可证的类型和数量。

有关可在 BES-53248 集群交换机上使用的许可证类型的详细信息,请参见 "为 BES-53248 集群交换机安装许可证"

例如,要激活 SW-BES54241-40-100G-LIC 许可证,必须取消注释 RCF 中的以下部分:

.
.
!
! 2-port or 6-port 40/100GbE node port license block
!
interface 0/49
no shutdown
description "40/100GbE Node Port"
!speed 100G full-duplex
speed 40G full-duplex
service-policy in WRED_100G
spanning-tree edgeport
mtu 9216
switchport mode trunk
datacenter-bridging
priority-flow-control mode on
priority-flow-control priority 5 no-drop
exit
exit
!
interface 0/50
no shutdown
description "40/100GbE Node Port"
!speed 100G full-duplex
speed 40G full-duplex
service-policy in WRED_100G
spanning-tree edgeport
mtu 9216
switchport mode trunk
datacenter-bridging
priority-flow-control mode on
priority-flow-control priority 5 no-drop
exit
exit
!
interface 0/51
no shutdown
description "40/100GbE Node Port"
speed 100G full-duplex
!speed 40G full-duplex
service-policy in WRED_100G
spanning-tree edgeport
mtu 9216
switchport mode trunk
datacenter-bridging
priority-flow-control mode on
priority-flow-control priority 5 no-drop
exit
exit
!
interface 0/52
no shutdown
description "40/100GbE Node Port"
speed 100G full-duplex
!speed 40G full-duplex
service-policy in WRED_100G
spanning-tree edgeport
mtu 9216
switchport mode trunk
datacenter-bridging
priority-flow-control mode on
priority-flow-control priority 5 no-drop
exit
exit
!
interface 0/53
no shutdown
description "40/100GbE Node Port"
speed 100G full-duplex
!speed 40G full-duplex
service-policy in WRED_100G
spanning-tree edgeport
mtu 9216
switchport mode trunk
datacenter-bridging
priority-flow-control mode on
priority-flow-control priority 5 no-drop
exit
exit
!
interface 0/54
no shutdown
description "40/100GbE Node Port"
speed 100G full-duplex
!speed 40G full-duplex
service-policy in WRED_100G
spanning-tree edgeport
mtu 9216
switchport mode trunk
datacenter-bridging
priority-flow-control mode on
priority-flow-control priority 5 no-drop
exit
exit
!
.
.
注 对于介于 0/49 到 0/54 之间的高速端口,取消对每个端口的注释,但在 RCF 中仅对其中每个端口的一条 * 速度 * 线取消注释,可以:
  • 速度 100G 全双工

  • 速度 40G 全双工

如示例所示。

对于介于 0/17 到 0/48 之间的低速度端口,激活相应的许可证后,取消对整个 8 端口部分的注释。