Skip to main content
Cluster and storage switches
简体中文版经机器翻译而成,仅供参考。如与英语版出现任何冲突,应以英语版为准。

完成从CN1610交换机到3232C交换机的迁移

贡献者

完成以下步骤以完成CN1610交换机到Nexus 3232C交换机的迁移。

步骤
  1. 还原所有节点上最初连接到C1的所有已迁移集群互连LIF:

    network interface revert -server cluster -lif lif-name

    显示示例

    您必须分别迁移每个 LIF ,如以下示例所示:

    cluster::*> network interface revert -vserver cluster -lif n1_clus1
    cluster::*> network interface revert -vserver cluster -lif n1_clus4
    cluster::*> network interface revert -vserver cluster -lif n2_clus1
    cluster::*> network interface revert -vserver cluster -lif n2_clus4
  2. 验证接口现在是否为主:

    network interface show -role cluster

    显示示例

    以下示例显示了节点 n1 和 n2 的集群互连接口状态为 up 和 "is Home" :

    cluster::*> network interface show -role cluster
    (network interface show)
             Logical    Status      Network        Current  Current  Is
    Vserver  Interface  Admin/Oper  Address/Mask   Node     Port     Home
    -------- ---------- ----------- -------------- -------- -------- -----
    Cluster
             n1_clus1   up/up       10.10.0.1/24   n1       e0a      true
             n1_clus2   up/up       10.10.0.2/24   n1       e0b      true
             n1_clus3   up/up       10.10.0.3/24   n1       e0c      true
             n1_clus4   up/up       10.10.0.4/24   n1       e0d      true
             n2_clus1   up/up       10.10.0.5/24   n2       e0a      true
             n2_clus2   up/up       10.10.0.6/24   n2       e0b      true
             n2_clus3   up/up       10.10.0.7/24   n2       e0c      true
             n2_clus4   up/up       10.10.0.8/24   n2       e0d      true
    
    8 entries were displayed.
  3. 验证远程集群接口的连接:

ONTAP 9.9.1及更高版本

您可以使用 network interface check cluster-connectivity 命令启动集群连接的可访问性检查、然后显示详细信息:

network interface check cluster-connectivity startnetwork interface check cluster-connectivity show

cluster1::*> network interface check cluster-connectivity start

*注:*请等待几秒钟、然后再运行 `show`命令以显示详细信息。

cluster1::*> network interface check cluster-connectivity show
                                  Source           Destination      Packet
Node   Date                       LIF              LIF              Loss
------ -------------------------- ---------------- ---------------- -----------
n1
       3/5/2022 19:21:18 -06:00   n1_clus2         n2-clus1         none
       3/5/2022 19:21:20 -06:00   n1_clus2         n2_clus2         none

n2
       3/5/2022 19:21:18 -06:00   n2_clus2         n1_clus1         none
       3/5/2022 19:21:20 -06:00   n2_clus2         n1_clus2         none
所有ONTAP版本

对于所有ONTAP版本、您还可以使用 cluster ping-cluster -node <name> 用于检查连接的命令:

cluster ping-cluster -node <name>

cluster1::*> cluster ping-cluster -node local
Host is n1
Getting addresses from network interface table...
Cluster n1_clus1 n1       e0a    10.10.0.1
Cluster n1_clus2 n1       e0b    10.10.0.2
Cluster n1_clus3 n1       e0c    10.10.0.3
Cluster n1_clus4 n1       e0d    10.10.0.4
Cluster n2_clus1 n2       e0a    10.10.0.5
Cluster n2_clus2 n2       e0b    10.10.0.6
Cluster n2_clus3 n2       e0c    10.10.0.7
Cluster n2_clus4 n2       e0d    10.10.0.8
Local = 10.10.0.1 10.10.0.2 10.10.0.3 10.10.0.4
Remote = 10.10.0.5 10.10.0.6 10.10.0.7 10.10.0.8
Cluster Vserver Id = 4294967293 Ping status:
....
Basic connectivity succeeds on 16 path(s)
Basic connectivity fails on 0 path(s)
................
Detected 9000 byte MTU on 16 path(s):
    Local 10.10.0.1 to Remote 10.10.0.5
    Local 10.10.0.1 to Remote 10.10.0.6
    Local 10.10.0.1 to Remote 10.10.0.7
    Local 10.10.0.1 to Remote 10.10.0.8
    Local 10.10.0.2 to Remote 10.10.0.5
    Local 10.10.0.2 to Remote 10.10.0.6
    Local 10.10.0.2 to Remote 10.10.0.7
    Local 10.10.0.2 to Remote 10.10.0.8
    Local 10.10.0.3 to Remote 10.10.0.5
    Local 10.10.0.3 to Remote 10.10.0.6
    Local 10.10.0.3 to Remote 10.10.0.7
    Local 10.10.0.3 to Remote 10.10.0.8
    Local 10.10.0.4 to Remote 10.10.0.5
    Local 10.10.0.4 to Remote 10.10.0.6
    Local 10.10.0.4 to Remote 10.10.0.7
    Local 10.10.0.4 to Remote 10.10.0.8

Larger than PMTU communication succeeds on 16 path(s)
RPC status:
4 paths up, 0 paths down (tcp check)
3 paths up, 0 paths down (udp check)
  1. 通过向Nexus 3232C集群交换机添加节点来扩展集群。

  2. 显示有关配置中的设备的信息:

    • network device-discovery show

    • network port show -role cluster

    • network interface show -role cluster

    • ssystem cluster-switch show

      显示示例

      以下示例显示了两个Nexus 3232C集群交换机上分别连接到端口E1/7和E1/8的40 GbE集群端口的节点n3和n4。两个节点均已加入集群。使用的 40 GbE 集群互连端口为 E4A 和 e4e 。

      cluster::*> network device-discovery show
      
             Local  Discovered
      Node   Port   Device       Interface       Platform
      ------ ------ ------------ --------------- -------------
      n1     /cdp
              e0a   C1           Ethernet1/1/1   N3K-C3232C
              e0b   C2           Ethernet1/1/1   N3K-C3232C
              e0c   C2           Ethernet1/1/2   N3K-C3232C
              e0d   C1           Ethernet1/1/2   N3K-C3232C
      n2     /cdp
              e0a   C1           Ethernet1/1/3   N3K-C3232C
              e0b   C2           Ethernet1/1/3   N3K-C3232C
              e0c   C2           Ethernet1/1/4   N3K-C3232C
              e0d   C1           Ethernet1/1/4   N3K-C3232C
      
      n3     /cdp
              e4a   C1           Ethernet1/7     N3K-C3232C
              e4e   C2           Ethernet1/7     N3K-C3232C
      
      n4     /cdp
              e4a   C1           Ethernet1/8     N3K-C3232C
              e4e   C2           Ethernet1/8     N3K-C3232C
      
      12 entries were displayed.
      cluster::*> network port show -role cluster
      (network port show)
      
      Node: n1
                      Broadcast              Speed (Mbps) Health   Ignore
      Port  IPspace   Domain     Link  MTU   Admin/Open   Status   Health Status
      ----- --------- ---------- ----- ----- ------------ -------- -------------
      e0a   cluster   cluster    up    9000  auto/10000     -
      e0b   cluster   cluster    up    9000  auto/10000     -
      e0c   cluster   cluster    up    9000  auto/10000     -        -
      e0d   cluster   cluster    up    9000  auto/10000     -        -
      
      Node: n2
                      Broadcast              Speed (Mbps) Health   Ignore
      Port  IPspace   Domain     Link  MTU   Admin/Open   Status   Health Status
      ----- --------- ---------- ----- ----- ------------ -------- -------------
      e0a   cluster   cluster    up    9000  auto/10000     -
      e0b   cluster   cluster    up    9000  auto/10000     -
      e0c   cluster   cluster    up    9000  auto/10000     -
      e0d   cluster   cluster    up    9000  auto/10000     -        -
      
      Node: n3
                      Broadcast              Speed (Mbps) Health   Ignore
      Port  IPspace   Domain     Link  MTU   Admin/Open   Status   Health Status
      ----- --------- ---------- ----- ----- ------------ -------- -------------
      e4a   cluster   cluster    up    9000  auto/40000     -
      e4e   cluster   cluster    up    9000  auto/40000     -        -
      
      Node: n4
                      Broadcast              Speed (Mbps) Health   Ignore
      Port  IPspace   Domain     Link  MTU   Admin/Open   Status   Health Status
      ----- --------- ---------- ----- ----- ------------ -------- -------------
      e4a   cluster   cluster    up    9000  auto/40000     -
      e4e   cluster   cluster    up    9000  auto/40000     -
      
      12 entries were displayed.
      
      cluster::*> network interface show -role cluster
      (network interface show)
               Logical    Status      Network        Current  Current  Is
      Vserver  Interface  Admin/Oper  Address/Mask   Node     Port     Home
      -------- ---------- ----------- -------------- -------- -------- -----
      Cluster
               n1_clus1   up/up       10.10.0.1/24   n1       e0a      true
               n1_clus2   up/up       10.10.0.2/24   n1       e0b      true
               n1_clus3   up/up       10.10.0.3/24   n1       e0c      true
               n1_clus4   up/up       10.10.0.4/24   n1       e0d      true
               n2_clus1   up/up       10.10.0.5/24   n2       e0a      true
               n2_clus2   up/up       10.10.0.6/24   n2       e0b      true
               n2_clus3   up/up       10.10.0.7/24   n2       e0c      true
               n2_clus4   up/up       10.10.0.8/24   n2       e0d      true
               n3_clus1   up/up       10.10.0.9/24   n3       e4a      true
               n3_clus2   up/up       10.10.0.10/24  n3       e4e      true
               n4_clus1   up/up       10.10.0.11/24  n4       e4a     true
               n4_clus2   up/up       10.10.0.12/24  n4       e4e     true
      
      12 entries were displayed.
      
      cluster::> system cluster-switch show
      
      Switch                      Type             Address       Model
      --------------------------- ---------------- ------------- ---------
      C1                          cluster-network  10.10.1.103   NX3232C
      
           Serial Number: FOX000001
            Is Monitored: true
                  Reason:
        Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                          7.0(3)I6(1)
          Version Source: CDP
      
      C2                          cluster-network  10.10.1.104   NX3232C
      
           Serial Number: FOX000002
            Is Monitored: true
                  Reason:
        Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                          7.0(3)I6(1)
          Version Source: CDP
      CL1                         cluster-network  10.10.1.101   CN1610
      
           Serial Number: 01234567
            Is Monitored: true
                  Reason:
        Software Version: 1.2.0.7
          Version Source: ISDP
      CL2                         cluster-network  10.10.1.102    CN1610
      
           Serial Number: 01234568
            Is Monitored: true
                  Reason:
        Software Version: 1.2.0.7
          Version Source: ISDP 4 entries were displayed.
  3. 如果未自动删除更换的 CN1610 交换机,请将其卸下:

    system cluster-switch delete -device switch-name

    显示示例

    您必须分别删除这两个设备,如以下示例所示:

    cluster::> system cluster-switch delete –device CL1
    cluster::> system cluster-switch delete –device CL2
  4. 验证是否监控了正确的集群交换机:

    ssystem cluster-switch show

    显示示例

    以下示例显示正在监控集群交换机 C1 和 C2 :

    cluster::> system cluster-switch show
    
    Switch                      Type               Address          Model
    --------------------------- ------------------ ---------------- ---------------
    C1                          cluster-network    10.10.1.103      NX3232C
    
         Serial Number: FOX000001
          Is Monitored: true
                Reason:
      Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                        7.0(3)I6(1)
        Version Source: CDP
    
    C2                          cluster-network    10.10.1.104      NX3232C
         Serial Number: FOX000002
          Is Monitored: true
              Reason:
      Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                        7.0(3)I6(1)
        Version Source: CDP
    
    2 entries were displayed.
  5. 如果禁止自动创建案例,请通过调用 AutoSupport 消息重新启用它:

    ssystem node AutoSupport invoke -node * -type all -message MAINT=end

下一步是什么?

"配置交换机运行状况监控"(英文)