简体中文版经机器翻译而成，仅供参考。如与英语版出现任何冲突，应以英语版为准。
升级您的参考配置文件 (RCF)
贡献者
建议更改
PDF
当您的运行交换机上已安装了现有版本的 RCF 文件时，您需要升级 RCF 版本。
开始之前
请确保您拥有以下物品：
-
交换机配置的当前备份。
-
一个功能齐全的集群（日志中没有错误或类似问题）。
-
当前的RCF。
-
如果您要更新 RCF 版本，则需要在 RCF 中进行启动配置，以反映所需的启动映像。
如果需要更改启动配置以反映当前的启动映像，则必须在重新应用 RCF 之前进行更改，以便在以后的重启中实例化正确的版本。
|
在此过程中不需要任何可操作的交换机间链路 (ISL)。这是设计使然，因为 RCF 版本的更改可能会暂时影响 ISL 连接。为确保集群运行不中断，以下步骤将所有集群 LIF 迁移到运行伙伴交换机，同时在目标交换机上执行相应步骤。 |
|
安装新的交换机软件版本和 RCF 之前，必须清除交换机设置并执行基本配置。您必须使用串行控制台连接到交换机，或者在擦除交换机设置之前保留基本配置信息。 |
第一步：准备升级
-
如果此集群上启用了AutoSupport ，则通过调用AutoSupport消息来抑制自动创建案例：
system node autosupport invoke -node * -type all -message MAINT=xh其中 x 为维护窗口的持续时间（小时）。
-
将权限级别更改为高级，并在提示继续时输入 y：
set -privilege advanced出现高级提示符（*>）。
-
显示每个节点上连接到交换机的集群端口：
network device-discovery show显示示例
cluster1::*> network device-discovery show Node/ Local Discovered Protocol Port Device (LLDP: ChassisID) Interface Platform ----------- ------ ------------------------- ---------------- -------- node1-01/cdp e10a cs1(FLMXXXXXXXX) Ethernet1/16/3 N9K-C9364D-GX2A e10b cs1(FDOXXXXXXXX) Ethernet1/13/3 N9K-C9364D-GX2A e11a cs1(FLMXXXXXXXX) Ethernet1/16/4 N9K-C9364D-GX2A e11b cs1(FDOXXXXXXXX) Ethernet1/13/4 N9K-C9364D-GX2A e1a cs1(FLMXXXXXXXX) Ethernet1/16/1 N9K-C9364D-GX2A e1b cs1(FDOXXXXXXXX) Ethernet1/13/1 N9K-C9364D-GX2A . . . e7a cs1(FLMXXXXXXXX) Ethernet1/16/2 N9K-C9364D-GX2A e7b cs1(FDOXXXXXXXX) Ethernet1/13/2 N9K-C9364D-GX2A node1-01/lldp e10a cs1 (c8:60:8f:xx:xx:xx) Ethernet1/16/3 - e10b cs2 (04:e3:87:xx:xx:xx) Ethernet1/16/3 - e11a cs1 (c8:60:8f:xx:xx:xx) Ethernet1/16/4 - e11b cs2 (04:e3:87:xx:xx:xx) Ethernet1/16/4 - e1a cs1 (c8:60:8f:xx:xx:xx) Ethernet1/16/1 - e1b cs2 (04:e3:87:xx:xx:xx) Ethernet1/16/1 - . . . e7a cs1 (c8:60:8f:xx:xx:xx) Ethernet1/16/2 - e7b cs2 (04:e3:87:xx:xx:xx) Ethernet1/16/2 - . . . -
检查各港口的行政及营运状况。
-
集群端口
-
确认集群所有端口均已启动且状态正常：
network port show -ipspace Cluster显示示例
cluster1::*> network port show -ipspace Cluster Node: node1-01 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ----------- -------- ------ e7a Cluster Cluster up 9000 auto/100000 healthy false e7b Cluster Cluster up 9000 auto/100000 healthy false Node:node1-02 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ----------- -------- ------ e7a Cluster Cluster up 9000 auto/100000 healthy false e7b Cluster Cluster up 9000 auto/100000 healthy false Node: node1-03 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ----------- -------- ------ e7a Cluster Cluster up 9000 auto/10000 healthy false e7b Cluster Cluster up 9000 auto/10000 healthy false Node: node1-04 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ----------- -------- ------ e7a Cluster Cluster up 9000 auto/10000 healthy false e7b Cluster Cluster up 9000 auto/10000 healthy false cluster1::*> -
确认所有集群接口（LIF）都位于主端口上：
network interface show -role cluster显示示例
cluster1::*> network interface show -role cluster Logical Status Network Current Current Is Vserver Interface Admin/Oper Address/Mask Node Port Home ----------- ---------------- ----------- ----------------- ------------ ------- ---- Cluster node1-01_clus1 up/up 169.254.3.4/23 node1-01 e7a true node1-01_clus2 up/up 169.254.3.5/23 node1-01 e7b true node1-02_clus1 up/up 169.254.3.8/23 node1-02 e7a true node1-02_clus2 up/up 169.254.3.9/23 node1-02 e7b true node1-03_clus1 up/up 169.254.1.3/23 node1-03 e7a true node1-03_clus2 up/up 169.254.1.1/23 node1-03 e7b true node1-04_clus1 up/up 169.254.1.6/23 node1-04 e7a true node1-04_clus2 up/up 169.254.1.7/23 node1-04 e7b true 8 entries were displayed. -
验证集群是否显示两个交换机的信息：
system cluster-switch show -is-monitoring-enabled-operational true显示示例
cluster1::*> system cluster-switch show -is-monitoring-enabled-operational true Switch Type Address Model --------------------------- ------------------ ---------------- ----- cs1(FDOXXXXXXXX) cluster-network 10.228.137.233 N9K-C9364D-GX2A Serial Number: FDOXXXXXXXX Is Monitored: true Reason: None Software Version: Cisco Nexus Operating System (NX-OS) Software, Version 10.4(2) Version Source: CDP/ISDP cs2(FLMXXXXXXXX) cluster-network 10.228.137.234 N9K-C9364D-GX2A Serial Number: FLMXXXXXXXX Is Monitored: true Reason: None Software Version: Cisco Nexus Operating System (NX-OS) Software, Version 10.4(2) Version Source: CDP/ISDP
-
-
HA 端口
-
验证所有 HA 端口是否处于正常运行状态：
ha interconnect status show -node <node-name>
-
显示示例
cluster1::*> ha interconnect status show -node node1-01 (system ha interconnect status show) Node: node1-01 Link 0 Status: up Link 1 Status: up Is Link 0 Active: true Is Link 1 Active: true IC RDMA Connection: up Slot: 0 Debug Firmware: no Interconnect Port 0 : Port Name: e1a-17 MTU: 4096 Link Information: ACTIVE Interconnect Port 1 : Port Name: e1b-18 MTU: 4096 Link Information: ACTIVE cluster1::*> ha interconnect status show -node node1-01 (system ha interconnect status show) Node: node1-01 Link 0 Status: up Link 1 Status: up Is Link 0 Active: true Is Link 1 Active: true IC RDMA Connection: up Slot: 0 Debug Firmware: no Interconnect Port 0 : Port Name: e1a-17 MTU: 4096 Link Information: ACTIVE Interconnect Port 1 : Port Name: e1b-18 MTU: 4096 Link Information: ACTIVE . . .-
存储端口
-
验证所有存储端口均处于正常状态：
storage port show -port-type ENET显示示例
cluster1::*> storage port show -port-type ENET Speed Node Port Type Mode (Gb/s) State Status ------------------ ---- ----- ------- ------ -------- ----------- node1-01 e10a ENET - 100 enabled online e10b ENET - 100 enabled online e11a ENET - 100 enabled online e11b ENET - 100 enabled online node1-02 e10a ENET - 100 enabled online e10b ENET - 100 enabled online e11a ENET - 100 enabled online e11b ENET - 100 enabled online node1-03 e10a ENET - 100 enabled online e10b ENET - 100 enabled online e11a ENET - 100 enabled online node1-04 e10a ENET - 100 enabled online e10b ENET - 100 enabled online e11a ENET - 100 enabled online e11b ENET - 100 enabled online 16 entries were displayed.
-
-
存储架端口
-
验证所有存储架端口是否处于正常状态：
storage shelf port show显示示例
cluster1::*> storage shelf port show Shelf ID Module State Internal? ----- -- ------ ------------ --------- 1.1 0 A connected false 1 A connected false 2 A connected false 3 A connected false 4 A connected false 5 A connected false 6 A connected false 7 A connected false 8 B connected false 9 B connected false 10 B connected false 11 B connected false 12 B connected false 13 B connected false 14 B connected false 15 B connected false 16 entries were displayed. -
验证所有存储架端口的连接状态：
storage shelf port show -fields remote-device,remote-port,connector-state显示示例
cluster1::*> storage shelf port show -fields remote-device,remote-port,connector-state shelf id connector-state remote-port remote-device ----- -- --------------- -------------- ----------------- 1.1 0 connected Ethernet1/17/1 CX9332D-cs1 1.1 1 connected Ethernet1/15/1 CX9364D-cs1 1.1 2 connected Ethernet1/17/2 CX9332D-cs1 1.1 3 connected Ethernet1/15/2 CX9364D-cs1 1.1 4 connected Ethernet1/17/3 CX9332D-cs1 1.1 5 connected Ethernet1/15/3 CX9364D-cs1 1.1 6 connected Ethernet1/17/4 CX9332D-cs1 1.1 7 connected Ethernet1/15/4 CX9364D-cs1 1.1 8 connected Ethernet1/19/1 CX9332D-cs1 1.1 9 connected Ethernet1/17/1 CX9364D-cs1 1.1 10 connected Ethernet1/19/2 CX9332D-cs1 1.1 11 connected Ethernet1/17/2 CX9364D-cs1 1.1 12 connected Ethernet1/19/3 CX9332D-cs1 1.1 13 connected Ethernet1/17/3 CX9364D-cs1 1.1 14 connected Ethernet1/19/4 CX9332D-cs1 1.1 15 connected Ethernet1/17/4 CX9364D-cs1 16 entries were displayed.
-
-
-
禁用集群 LIF 的自动回滚功能：
network interface modify -vserver Cluster -lif * -auto-revert false
步骤 2：配置端口
-
在交换机cs1上，关闭与节点所有端口相连的端口。
cs1# config cs1(config)# interface e1/1/1-4,e1/2/1-4,e1/3/1-4,e1/4/1-4,e1/5/1-4,e1/6/1-4,e1/7/1-4,e1/8/1-4 cs1(config-if-range)# shutdown cs1(config)# interface e1/9/1-4,e1/10/1-4,e1/11/1-4,e1/12/1-4,e1/13/1-4,e1/14/1-4,e1/15/1-4,e1/16/1-4 cs1(config-if-range)# shutdown cs1(config)# interface e1/17/1-4,e1/18/1-4,e1/19/1-4,e1/20/1-4,e1/21/1-4,e1/22/1-4,e1/23/1-4,e1/24/1-4 cs1(config-if-range)# shutdown cs1(config)# interface e1/25/1-4,e1/26/1-4,e1/27/1-4,e1/28/1-4,e1/29/1-4,e1/30/1-4,e1/31/1-4,e1/32/1-4 cs1(config-if-range)# shutdown cs1(config)# interface e1/33/1-4,e1/34/1-4,e1/35/1-4,e1/36/1-4,e1/37/1-4,e1/38/1-4,e1/39/1-4,e1/40/1-4 cs1(config-if-range)# shutdown cs1(config)# interface e1/41/1-4,e1/42/1-4,e1/43/1-4,e1/44/1-4,e1/35/1-4,e1/46/1-4,e1/47/1-4,e1/48/1-4 cs1(config-if-range)# shutdown cs1(config)# interface e1/49/1-4,e1/50/1-4,e1/51/1-4,e1/52/1-4,e1/53/1-4,e1/54/1-4,e1/55/1-4,e1/56/1-4 cs1(config-if-range)# shutdown cs1(config)# interface e1/57/1-4,e1/58/1-4,e1/59/1-4,e1/60/1-4,e1/61/1-4,e1/62/1-4 cs1(config-if-range)# shutdown cs1(config-if-range)# exit cs1(config)# exit
确保关闭所有连接的端口以避免任何网络连接问题。请参阅知识库文章 "在切换操作系统升级期间迁移集群 LIF 时，节点脱离仲裁。"更多详情请见下文。 -
验证集群 LIF 是否已故障转移到集群交换机 cs1 上托管的端口。这可能需要几秒钟。
network interface show -role cluster显示示例
cluster1::*> network interface show -role cluster Logical Status Network Current Current Is Vserver Interface Admin/Oper Address/Mask Node Port Home ----------- ----------------- ---------- ------------------ ------------- ------- ---- Cluster node1-01_clus1 up/up 169.254.36.44/16 node1-01 e7a true node1-01_clus2 up/up 169.254.7.5/16 node1-01 e7b true node1-02_clus1 up/up 169.254.197.206/16 node1-02 e7a true node1-02_clus2 up/up 169.254.195.186/16 node1-02 e7b true node1-03_clus1 up/up 169.254.192.49/16 node1-03 e7a true node1-03_clus2 up/up 169.254.182.76/16 node1-03 e7b true node1-04_clus1 up/up 169.254.59.49/16 node1-04 e7a true node1-04_clus2 up/up 169.254.62.244/16 node1-04 e7b true 8 entries were displayed. -
验证集群是否运行正常：
cluster show显示示例
cluster1::*> cluster show Node Health Eligibility Epsilon ----------------- ------- ------------ ------- node1-01 true true false node1-02 true true false node1-03 true true true node1-04 true true false 4 entries were displayed.
-
如果您尚未保存当前交换机配置，请将以下命令的输出复制到文本文件中：
show running-config-
记录当前版本与当前版本之间的任何自定义添加内容。 `running-config`以及正在使用的 RCF 文件（例如贵组织的 SNMP 配置）。
-
对于 NX-OS 10.2 及更高版本，请使用 `show diff running-config`用于与 bootflash 中保存的 RCF 文件进行比较的命令。否则，请使用第三方差异/比较工具。
-
-
保存基本配置详细信息 `write_erase.cfg`启动闪存上的文件。
确保配置以下内容：
-
用户名和密码
-
管理 IP 地址
-
默认网关
-
交换机名称
cs1# show run | i "username admin password" > bootflash:write_erase.cfgcs1# show run | section "vrf context management" >> bootflash:write_erase.cfgcs1# show run | section "interface mgmt0" >> bootflash:write_erase.cfgcs1# show run | section "switchname" >> bootflash:write_erase.cfgcs1# echo "hardware access-list tcam region ing-racl 1024" >> bootflash:write_erase.cfgcs1# echo "hardware access-list tcam region egr-racl 1024" >> bootflash:write_erase.cfgcs1# echo "hardware access-list tcam region ing-l2-qos 1536" >> bootflash:write_erase.cfg请参阅知识库文章"如何在保持远程连接的情况下清除Cisco互连交换机上的配置"更多详情请见下文。
-
-
确认 `write_erase.cfg`文件已按预期填充：
show file bootflash:write_erase.cfg -
问题 `write erase`清除当前已保存配置的命令：
cs1# write eraseWarning: This command will erase the startup-configuration.Do you wish to proceed anyway? (y/n) [n] y -
将之前保存的基本配置复制到启动配置中。
cs1# copy bootflash:write_erase.cfg startup-config -
重启交换机：
cs1# reloadThis command will reboot the system. (y/n)? [n] y -
管理 IP 地址恢复正常后，通过 SSH 登录交换机。
您可能需要更新与 SSH 密钥相关的 hosts 文件条目。
-
使用以下传输协议之一将 RCF 复制到交换机 cs1 的 bootflash：FTP、TFTP、SFTP 或 SCP。
有关Cisco命令的更多信息，请参阅 "Cisco Nexus 9000 系列 NX-OS 命令参考"指南。
显示示例
此示例展示了如何使用 TFTP 将 RCF 文件复制到交换机 cs1 的启动闪存中：
cs1# copy tftp: bootflash: vrf management Enter source filename: NX9364D-GX2A-RCF-v10.0-Shared.txt Enter hostname for the tftp server: 172.22.201.50 Trying to connect to tftp server......Connection to Server Established. TFTP get operation was successful Copy complete, now saving to disk (please wait)...
-
将之前下载的 RCF 文件应用到启动闪存中。
有关Cisco命令的更多信息，请参阅 "Cisco Nexus 9000 系列 NX-OS 命令参考"指南。
此示例展示了 RCF 文件 `NX9364D-GX2A-RCF-v10.0-Shared.txt`正在交换机 cs1 上安装：
cs1# copy NX9364D-GX2A-RCF-v10.0-Shared.txt running-config echo-commands
请务必仔细阅读 RCF 的 安装说明、重要说明 和 横幅 部分。您必须阅读并遵循这些说明以确保交换机的正确配置和操作。 -
请确认 RCF 文件是否为最新版本：
show running-config检查输出结果以验证是否拥有正确的 RCF 时，请确保以下信息正确：
-
RCF横幅
-
节点和端口设置
-
定制
输出结果会根据您的网站配置而有所不同。检查端口设置，并参考发行说明，了解您安装的 RCF 版本是否有任何特定更改。
-
-
将之前对交换机配置所做的任何自定义设置重新应用。
-
确认 RCF 版本、自定义添加项和交换机设置正确后，将运行配置文件复制到启动配置文件。
有关Cisco命令的更多信息，请参阅 "Cisco Nexus 9000 系列 NX-OS 命令参考"指南。
cs1# copy running-config startup-config[] 100% Copy complete -
重启交换机cs1。在交换机重启期间，您可以忽略节点上报告的“集群交换机健康监视器”警报和“集群端口关闭”事件。
cs1# reloadThis command will reboot the system. (y/n)? [n] y -
验证集群上端口的健康状况。
-
集群端口
-
确认集群中所有节点的集群端口均已启动且运行状况良好：
network port show -ipspace Cluster显示示例
cluster1::*> network port show -ipspace Cluster Node: node1-01 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ----------- -------- ------ e7a Cluster Cluster up 9000 auto/10000 healthy false e7b Cluster Cluster up 9000 auto/10000 healthy false Node: node1-02 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ----------- -------- ------ e7a Cluster Cluster up 9000 auto/10000 healthy false e7b Cluster Cluster up 9000 auto/10000 healthy false Node: node1-03 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ----------- -------- ------ e7a Cluster Cluster up 9000 auto/100000 healthy false e7b Cluster Cluster up 9000 auto/100000 healthy false Node: node1-04 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ----------- -------- ------ e7a Cluster Cluster up 9000 auto/100000 healthy false e7b Cluster Cluster up 9000 auto/100000 healthy false 8 entries were displayed. -
从集群中验证交换机的运行状况。
network device-discovery show -protocol cdpsystem cluster-switch show -is-monitoring-enabled-operational true显示示例
cluster1::*> network device-discovery show -protocol cdp Node/ Local Discovered Protocol Port Device (LLDP: ChassisID) Interface Platform ----------- ------ ------------------------- ----------------- -------- node1-01/cdp e10a cs1(FLMXXXXXXXX) Ethernet1/16/3 N9K-C9364D-GX2A e10b cs2(FDOXXXXXXXX) Ethernet1/13/3 N9K-C9364D-GX2A e11a cs1(FLMXXXXXXXX) Ethernet1/16/4 N9K-C9364D-GX2A e11b cs2(FDOXXXXXXXX) Ethernet1/13/4 N9K-C9364D-GX2A e1a cs1(FLMXXXXXXXX) Ethernet1/16/1 N9K-C9364D-GX2A e1b cs2(FLMXXXXXXXX) Ethernet1/13/1 N9K-C9364D-GX2A . . . e7a cs1(FLMXXXXXXXX) Ethernet1/16/2 N9K-C9364D-GX2A e7b cs2(FDOXXXXXXXX) Ethernet1/13/2 N9K-C9364D-GX2A node1-02/cdp . . . cluster1::*> system cluster-switch show -is-monitoring-enabled-operational true Switch Type Address Model --------------------------- ------------------ ---------------- ----- cs2(FDOXXXXXXXX) cluster-network 10.228.137.233 N9K-C9364D-GX2A Serial Number: FDOXXXXXXXX Is Monitored: true Reason: None Software Version: Cisco Nexus Operating System (NX-OS) Software, Version 10.4(2) Version Source: CDP/ISDP cs1(FLMXXXXXXXX) cluster-network 10.228.137.234 N9K-C9364D-GX2A Serial Number: FLMXXXXXXXX Is Monitored: true Reason: None Software Version: Cisco Nexus Operating System (NX-OS) Software, Version 10.4(2) Version Source: CDP/ISDP 2 entries were displayed.
-
-
HA 端口
-
验证所有 HA 端口是否处于正常运行状态：
ha interconnect status show -node <node-name>
-
显示示例
cluster1::*> ha interconnect status show -node node1-01 (system ha interconnect status show) Node: node1-01 Link 0 Status: up Link 1 Status: up Is Link 0 Active: true Is Link 1 Active: true IC RDMA Connection: up Slot: 0 Debug Firmware: no Interconnect Port 0 : Port Name: e1a-17 MTU: 4096 Link Information: ACTIVE Interconnect Port 1 : Port Name: e1b-18 MTU: 4096 Link Information: ACTIVE cluster1::*> ha interconnect status show -node node1-02 (system ha interconnect status show) Node: node1-02 Link 0 Status: up Link 1 Status: up Is Link 0 Active: true Is Link 1 Active: true IC RDMA Connection: up Slot: 0 Debug Firmware: no Interconnect Port 0 : Port Name: e1a-17 MTU: 4096 Link Information: ACTIVE Interconnect Port 1 : Port Name: e1b-18 MTU: 4096 Link Information: ACTIVE . . .-
存储端口
-
验证所有存储端口均处于正常状态：
storage port show -port-type ENET显示示例
cluster1::*> storage port show -port-type ENET Speed Node Port Type Mode (Gb/s) State Status ------------------ ---- ----- ------- ------ -------- ----------- node1-01 e10a ENET - 100 enabled online e10b ENET - 100 enabled online e11a ENET - 100 enabled online e11b ENET - 100 enabled online node1-02 e10a ENET - 100 enabled online e10b ENET - 100 enabled online e11a ENET - 100 enabled online e11b ENET - 100 enabled online node1-03 e10a ENET - 100 enabled online e10b ENET - 100 enabled online e11a ENET - 100 enabled online node1-04 e10a ENET - 100 enabled online e10b ENET - 100 enabled online e11a ENET - 100 enabled online e11b ENET - 100 enabled online 16 entries were displayed.
-
-
存储架端口
-
验证所有存储架端口是否处于正常状态：
storage shelf port show显示示例
cluster1::*> storage shelf port show Shelf ID Module State Internal? ----- -- ------ ------------ --------- 1.1 0 A connected false 1 A connected false 2 A connected false 3 A connected false 4 A connected false 5 A connected false 6 A connected false 7 A connected false 8 B connected false 9 B connected false 10 B connected false 11 B connected false 12 B connected false 13 B connected false 14 B connected false 15 B connected false 16 entries were displayed. -
验证所有存储架端口的连接状态：
storage shelf port show -fields remote-device,remote-port,connector-state显示示例
cluster1::*> storage shelf port show -fields remote-device,remote-port,connector-state shelf id connector-state remote-port remote-device ----- -- --------------- -------------- ----------------- 1.1 0 connected Ethernet1/17/1 CX9332D-cs1 1.1 1 connected Ethernet1/15/1 CX9364D-cs1 1.1 2 connected Ethernet1/17/2 CX9332D-cs1 1.1 3 connected Ethernet1/15/2 CX9364D-cs1 1.1 4 connected Ethernet1/17/3 CX9332D-cs1 1.1 5 connected Ethernet1/15/3 CX9364D-cs1 1.1 6 connected Ethernet1/17/4 CX9332D-cs1 1.1 7 connected Ethernet1/15/4 CX9364D-cs1 1.1 8 connected Ethernet1/19/1 CX9332D-cs1 1.1 9 connected Ethernet1/17/1 CX9364D-cs1 1.1 10 connected Ethernet1/19/2 CX9332D-cs1 1.1 11 connected Ethernet1/17/2 CX9364D-cs1 1.1 12 connected Ethernet1/19/3 CX9332D-cs1 1.1 13 connected Ethernet1/17/3 CX9364D-cs1 1.1 14 connected Ethernet1/19/4 CX9332D-cs1 1.1 15 connected Ethernet1/17/4 CX9364D-cs1 16 entries were displayed.
-
-
-
验证集群是否运行正常：
cluster show显示示例
cluster1::*> cluster show Node Health Eligibility Epsilon ----------------- -------- ------------- ------- node1-01 true true false node1-02 true true false node1-03 true true true node1-04 true true false 4 entries were displayed.
-
在交换机 cs2 上重复步骤 4 至 18。
-
启用集群 LIF 的自动回滚功能：
network interface modify -vserver Cluster -lif * -auto-revert True
步骤 3：验证集群网络配置和集群健康状况
-
确认连接到集群端口的交换机端口已开启。
show interface brief显示示例
cs1# show interface brief | grep up . . Eth1/9/3 1 eth trunk up none 100G(D) -- Eth1/9/4 1 eth trunk up none 100G(D) -- Eth1/15/1 1 eth trunk up none 100G(D) -- Eth1/15/2 1 eth trunk up none 100G(D) -- Eth1/15/3 1 eth trunk up none 100G(D) -- Eth1/15/4 1 eth trunk up none 100G(D) -- Eth1/16/1 1 eth trunk up none 100G(D) -- Eth1/16/2 1 eth trunk up none 100G(D) -- Eth1/16/3 1 eth trunk up none 100G(D) -- Eth1/16/4 1 eth trunk up none 100G(D) -- Eth1/17/1 1 eth trunk up none 100G(D) -- Eth1/17/2 1 eth trunk up none 100G(D) -- Eth1/17/3 1 eth trunk up none 100G(D) -- Eth1/17/4 1 eth trunk up none 100G(D) -- . . .
-
确认预期节点仍然连接：
show cdp neighbors显示示例
cs1# show cdp neighbors Capability Codes: R - Router, T - Trans-Bridge, B - Source-Route-Bridge S - Switch, H - Host, I - IGMP, r - Repeater, V - VoIP-Phone, D - Remotely-Managed-Device, s - Supports-STP-Dispute Device-ID Local Intrfce Hldtme Capability Platform Port ID cs2(FDOXXXXXXXX) Eth1/63 179 R S I s N9K-C9332D-GX2B Eth1/31 cs2(FDOXXXXXXXX) Eth1/64 179 R S I s N9K-C9332D-GX2B Eth1/32 node1-01 Eth1/4/1 123 H AFX-1K e1a node1-01 Eth1/4/2 123 H AFX-1K e7a node1-01 Eth1/4/3 123 H AFX-1K e10a node1-01 Eth1/4/4 123 H AFX-1K e11a node1-02 Eth1/9/1 138 H AFX-1K e1a node1-02 Eth1/9/2 138 H AFX-1K e7a node1-02 Eth1/9/3 138 H AFX-1K e10a node1-02 Eth1/9/4 138 H AFX-1K e11a node1-03 Eth1/15/1 138 H AFX-1K e1a node1-03 Eth1/15/2 138 H AFX-1K e7a node1-03 Eth1/15/3 138 H AFX-1K e10a node1-03 Eth1/15/4 138 H AFX-1K e11a node1-04 Eth1/16/1 173 H AFX-1K e1a node1-04 Eth1/16/2 173 H AFX-1K e7a node1-04 Eth1/16/3 173 H AFX-1K e10a node1-04 Eth1/16/4 173 H AFX-1K e11a Total entries displayed: 18 -
使用以下命令验证集群节点是否位于正确的集群 VLAN 中：
show vlan briefshow interface trunk显示示例
cs1# show vlan brief VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Po1, Po999, Eth1/63, Eth1/64 Eth1/65, Eth1/66, Eth1/1/1 Eth1/1/2, Eth1/1/3, Eth1/1/4 Eth1/2/1, Eth1/2/2, Eth1/2/3 Eth1/2/4, Eth1/3/1, Eth1/3/2 Eth1/3/3, Eth1/3/4, Eth1/4/1 Eth1/4/2, Eth1/4/3, Eth1/4/4 Eth1/5/1, Eth1/5/2, Eth1/5/3 Eth1/5/4, Eth1/6/1, Eth1/6/2 Eth1/6/3, Eth1/6/4, Eth1/7/1 Eth1/7/2, Eth1/7/3, Eth1/7/4 Eth1/8/1, Eth1/8/2, Eth1/8/3 Eth1/8/4, Eth1/9/1, Eth1/9/2 Eth1/9/3, Eth1/9/4, Eth1/10/1 Eth1/10/2, Eth1/10/3, Eth1/10/4 Eth1/11/1, Eth1/11/2, Eth1/11/3 Eth1/11/4, Eth1/12/1, Eth1/12/2 Eth1/12/3, Eth1/12/4, Eth1/13/1 Eth1/13/2, Eth1/13/3, Eth1/13/4 Eth1/14/1, Eth1/14/2, Eth1/14/3 Eth1/14/4, Eth1/15/1, Eth1/15/2 Eth1/15/3, Eth1/15/4, Eth1/16/1 Eth1/16/2, Eth1/16/3, Eth1/16/4 Eth1/17/1, Eth1/17/2, Eth1/17/3 Eth1/17/4, Eth1/18/1, Eth1/18/2 Eth1/18/3, Eth1/18/4, Eth1/19/1 Eth1/19/2, Eth1/19/3, Eth1/19/4 Eth1/20/1, Eth1/20/2, Eth1/20/3 Eth1/20/4, Eth1/21/1, Eth1/21/2 Eth1/21/3, Eth1/21/4, Eth1/22/1 Eth1/22/2, Eth1/22/3, Eth1/22/4 Eth1/23/1, Eth1/23/2, Eth1/23/3 Eth1/23/4, Eth1/24/1, Eth1/24/2 Eth1/24/3, Eth1/24/4, Eth1/25/1 Eth1/25/2, Eth1/25/3, Eth1/25/4 Eth1/26/1, Eth1/26/2, Eth1/26/3 Eth1/26/4, Eth1/27/1, Eth1/27/2 Eth1/27/3, Eth1/27/4, Eth1/28/1 Eth1/28/2, Eth1/28/3, Eth1/28/4 Eth1/29/1, Eth1/29/2, Eth1/29/3 Eth1/29/4, Eth1/30/1, Eth1/30/2 Eth1/30/3, Eth1/30/4, Eth1/31/1 Eth1/31/2, Eth1/31/3, Eth1/31/4 Eth1/32/1, Eth1/32/2, Eth1/32/3 Eth1/32/4, Eth1/33/1, Eth1/33/2 Eth1/33/3, Eth1/33/4, Eth1/34/1 Eth1/34/2, Eth1/34/3, Eth1/34/4 Eth1/35/1, Eth1/35/2, Eth1/35/3 Eth1/35/4, Eth1/36/1, Eth1/36/2 Eth1/36/3, Eth1/36/4, Eth1/37/1 Eth1/37/2, Eth1/37/3, Eth1/37/4 Eth1/38/1, Eth1/38/2, Eth1/38/3 Eth1/38/4, Eth1/39/1, Eth1/39/2 Eth1/39/3, Eth1/39/4, Eth1/40/1 Eth1/40/2, Eth1/40/3, Eth1/40/4 Eth1/41/1, Eth1/41/2, Eth1/41/3 Eth1/41/4, Eth1/42/1, Eth1/42/2 Eth1/42/3, Eth1/42/4, Eth1/43/1 Eth1/43/2, Eth1/43/3, Eth1/43/4 Eth1/44/1, Eth1/44/2, Eth1/44/3 Eth1/44/4, Eth1/45/1, Eth1/45/2 Eth1/45/3, Eth1/45/4, Eth1/46/1 Eth1/46/2, Eth1/46/3, Eth1/46/4 Eth1/47/1, Eth1/47/2, Eth1/47/3 Eth1/47/4, Eth1/48/1, Eth1/48/2 Eth1/48/3, Eth1/48/4, Eth1/49/1 Eth1/49/2, Eth1/49/3, Eth1/49/4 Eth1/50/1, Eth1/50/2, Eth1/50/3 Eth1/50/4, Eth1/51/1, Eth1/51/2 Eth1/51/3, Eth1/51/4, Eth1/52/1 Eth1/52/2, Eth1/52/3, Eth1/52/4 Eth1/53/1, Eth1/53/2, Eth1/53/3 Eth1/53/4, Eth1/54/1, Eth1/54/2 Eth1/54/3, Eth1/54/4, Eth1/55/1 Eth1/55/2, Eth1/55/3, Eth1/55/4 Eth1/56/1, Eth1/56/2, Eth1/56/3 Eth1/56/4, Eth1/57/1, Eth1/57/2 Eth1/57/3, Eth1/57/4, Eth1/58/1 Eth1/58/2, Eth1/58/3, Eth1/58/4 Eth1/59/1, Eth1/59/2, Eth1/59/3 Eth1/59/4, Eth1/60/1, Eth1/60/2 Eth1/60/3, Eth1/60/4, Eth1/61/1 Eth1/61/2, Eth1/61/3, Eth1/61/4 Eth1/62/1, Eth1/62/2, Eth1/62/3 Eth1/62/4 17 VLAN0017 active Eth1/1/1, Eth1/1/2, Eth1/1/3 Eth1/1/4, Eth1/2/1, Eth1/2/2 Eth1/2/3, Eth1/2/4, Eth1/3/1 Eth1/3/2, Eth1/3/3, Eth1/3/4 Eth1/4/1, Eth1/4/2, Eth1/4/3 Eth1/4/4, Eth1/5/1, Eth1/5/2 Eth1/5/3, Eth1/5/4, Eth1/6/1 Eth1/6/2, Eth1/6/3, Eth1/6/4 Eth1/7/1, Eth1/7/2, Eth1/7/3 Eth1/7/4, Eth1/8/1, Eth1/8/2 Eth1/8/3, Eth1/8/4, Eth1/9/1 Eth1/9/2, Eth1/9/3, Eth1/9/4 Eth1/10/1, Eth1/10/2, Eth1/10/3 Eth1/10/4, Eth1/11/1, Eth1/11/2 Eth1/11/3, Eth1/11/4, Eth1/12/1 Eth1/12/2, Eth1/12/3, Eth1/12/4 Eth1/13/1, Eth1/13/2, Eth1/13/3 Eth1/13/4, Eth1/14/1, Eth1/14/2 Eth1/14/3, Eth1/14/4, Eth1/15/1 Eth1/15/2, Eth1/15/3, Eth1/15/4 Eth1/16/1, Eth1/16/2, Eth1/16/3 Eth1/16/4, Eth1/17/1, Eth1/17/2 Eth1/17/3, Eth1/17/4, Eth1/18/1 Eth1/18/2, Eth1/18/3, Eth1/18/4 Eth1/19/1, Eth1/19/2, Eth1/19/3 Eth1/19/4, Eth1/20/1, Eth1/20/2 Eth1/20/3, Eth1/20/4, Eth1/21/1 Eth1/21/2, Eth1/21/3, Eth1/21/4 Eth1/22/1, Eth1/22/2, Eth1/22/3 Eth1/22/4, Eth1/23/1, Eth1/23/2 Eth1/23/3, Eth1/23/4, Eth1/24/1 Eth1/24/2, Eth1/24/3, Eth1/24/4 Eth1/25/1, Eth1/25/2, Eth1/25/3 Eth1/25/4, Eth1/26/1, Eth1/26/2 Eth1/26/3, Eth1/26/4, Eth1/27/1 Eth1/27/2, Eth1/27/3, Eth1/27/4 Eth1/28/1, Eth1/28/2, Eth1/28/3 Eth1/28/4, Eth1/29/1, Eth1/29/2 Eth1/29/3, Eth1/29/4, Eth1/30/1 Eth1/30/2, Eth1/30/3, Eth1/30/4 Eth1/31/1, Eth1/31/2, Eth1/31/3 Eth1/31/4, Eth1/32/1, Eth1/32/2 Eth1/32/3, Eth1/32/4, Eth1/33/1 Eth1/33/2, Eth1/33/3, Eth1/33/4 Eth1/34/1, Eth1/34/2, Eth1/34/3 Eth1/34/4, Eth1/35/1, Eth1/35/2 Eth1/35/3, Eth1/35/4, Eth1/36/1 Eth1/36/2, Eth1/36/3, Eth1/36/4 Eth1/37/1, Eth1/37/2, Eth1/37/3 Eth1/37/4, Eth1/38/1, Eth1/38/2 Eth1/38/3, Eth1/38/4, Eth1/39/1 Eth1/39/2, Eth1/39/3, Eth1/39/4 Eth1/40/1, Eth1/40/2, Eth1/40/3 Eth1/40/4, Eth1/41/1, Eth1/41/2 Eth1/41/3, Eth1/41/4, Eth1/42/1 Eth1/42/2, Eth1/42/3, Eth1/42/4 Eth1/43/1, Eth1/43/2, Eth1/43/3 Eth1/43/4, Eth1/44/1, Eth1/44/2 Eth1/44/3, Eth1/44/4, Eth1/45/1 Eth1/45/2, Eth1/45/3, Eth1/45/4 Eth1/46/1, Eth1/46/2, Eth1/46/3 Eth1/46/4, Eth1/47/1, Eth1/47/2 Eth1/47/3, Eth1/47/4, Eth1/48/1 Eth1/48/2, Eth1/48/3, Eth1/48/4 Eth1/49/1, Eth1/49/2, Eth1/49/3 Eth1/49/4, Eth1/50/1, Eth1/50/2 Eth1/50/3, Eth1/50/4, Eth1/51/1 Eth1/51/2, Eth1/51/3, Eth1/51/4 Eth1/52/1, Eth1/52/2, Eth1/52/3 Eth1/52/4, Eth1/53/1, Eth1/53/2 Eth1/53/3, Eth1/53/4, Eth1/54/1 Eth1/54/2, Eth1/54/3, Eth1/54/4 Eth1/55/1, Eth1/55/2, Eth1/55/3 Eth1/55/4, Eth1/56/1, Eth1/56/2 Eth1/56/3, Eth1/56/4, Eth1/57/1 Eth1/57/2, Eth1/57/3, Eth1/57/4 Eth1/58/1, Eth1/58/2, Eth1/58/3 Eth1/58/4, Eth1/59/1, Eth1/59/2 Eth1/59/3, Eth1/59/4, Eth1/60/1 Eth1/60/2, Eth1/60/3, Eth1/60/4 Eth1/61/1, Eth1/61/2, Eth1/61/3 Eth1/61/4, Eth1/62/1, Eth1/62/2 Eth1/62/3, Eth1/62/4 18 VLAN0018 active Eth1/1/1, Eth1/1/2, Eth1/1/3 Eth1/1/4, Eth1/2/1, Eth1/2/2 Eth1/2/3, Eth1/2/4, Eth1/3/1 Eth1/3/2, Eth1/3/3, Eth1/3/4 Eth1/4/1, Eth1/4/2, Eth1/4/3 Eth1/4/4, Eth1/5/1, Eth1/5/2 Eth1/5/3, Eth1/5/4, Eth1/6/1 Eth1/6/2, Eth1/6/3, Eth1/6/4 Eth1/7/1, Eth1/7/2, Eth1/7/3 Eth1/7/4, Eth1/8/1, Eth1/8/2 Eth1/8/3, Eth1/8/4, Eth1/9/1 Eth1/9/2, Eth1/9/3, Eth1/9/4 Eth1/10/1, Eth1/10/2, Eth1/10/3 Eth1/10/4, Eth1/11/1, Eth1/11/2 Eth1/11/3, Eth1/11/4, Eth1/12/1 Eth1/12/2, Eth1/12/3, Eth1/12/4 Eth1/13/1, Eth1/13/2, Eth1/13/3 Eth1/13/4, Eth1/14/1, Eth1/14/2 Eth1/14/3, Eth1/14/4, Eth1/15/1 Eth1/15/2, Eth1/15/3, Eth1/15/4 Eth1/16/1, Eth1/16/2, Eth1/16/3 Eth1/16/4, Eth1/17/1, Eth1/17/2 Eth1/17/3, Eth1/17/4, Eth1/18/1 Eth1/18/2, Eth1/18/3, Eth1/18/4 Eth1/19/1, Eth1/19/2, Eth1/19/3 Eth1/19/4, Eth1/20/1, Eth1/20/2 Eth1/20/3, Eth1/20/4, Eth1/21/1 Eth1/21/2, Eth1/21/3, Eth1/21/4 Eth1/22/1, Eth1/22/2, Eth1/22/3 Eth1/22/4, Eth1/23/1, Eth1/23/2 Eth1/23/3, Eth1/23/4, Eth1/24/1 Eth1/24/2, Eth1/24/3, Eth1/24/4 Eth1/25/1, Eth1/25/2, Eth1/25/3 Eth1/25/4, Eth1/26/1, Eth1/26/2 Eth1/26/3, Eth1/26/4, Eth1/27/1 Eth1/27/2, Eth1/27/3, Eth1/27/4 Eth1/28/1, Eth1/28/2, Eth1/28/3 Eth1/28/4, Eth1/29/1, Eth1/29/2 Eth1/29/3, Eth1/29/4, Eth1/30/1 Eth1/30/2, Eth1/30/3, Eth1/30/4 Eth1/31/1, Eth1/31/2, Eth1/31/3 Eth1/31/4, Eth1/32/1, Eth1/32/2 Eth1/32/3, Eth1/32/4, Eth1/33/1 Eth1/33/2, Eth1/33/3, Eth1/33/4 Eth1/34/1, Eth1/34/2, Eth1/34/3 Eth1/34/4, Eth1/35/1, Eth1/35/2 Eth1/35/3, Eth1/35/4, Eth1/36/1 Eth1/36/2, Eth1/36/3, Eth1/36/4 Eth1/37/1, Eth1/37/2, Eth1/37/3 Eth1/37/4, Eth1/38/1, Eth1/38/2 Eth1/38/3, Eth1/38/4, Eth1/39/1 Eth1/39/2, Eth1/39/3, Eth1/39/4 Eth1/40/1, Eth1/40/2, Eth1/40/3 Eth1/40/4, Eth1/41/1, Eth1/41/2 Eth1/41/3, Eth1/41/4, Eth1/42/1 Eth1/42/2, Eth1/42/3, Eth1/42/4 Eth1/43/1, Eth1/43/2, Eth1/43/3 Eth1/43/4, Eth1/44/1, Eth1/44/2 Eth1/44/3, Eth1/44/4, Eth1/45/1 Eth1/45/2, Eth1/45/3, Eth1/45/4 Eth1/46/1, Eth1/46/2, Eth1/46/3 Eth1/46/4, Eth1/47/1, Eth1/47/2 Eth1/47/3, Eth1/47/4, Eth1/48/1 Eth1/48/2, Eth1/48/3, Eth1/48/4 Eth1/49/1, Eth1/49/2, Eth1/49/3 Eth1/49/4, Eth1/50/1, Eth1/50/2 Eth1/50/3, Eth1/50/4, Eth1/51/1 Eth1/51/2, Eth1/51/3, Eth1/51/4 Eth1/52/1, Eth1/52/2, Eth1/52/3 Eth1/52/4, Eth1/53/1, Eth1/53/2 Eth1/53/3, Eth1/53/4, Eth1/54/1 Eth1/54/2, Eth1/54/3, Eth1/54/4 Eth1/55/1, Eth1/55/2, Eth1/55/3 Eth1/55/4, Eth1/56/1, Eth1/56/2 Eth1/56/3, Eth1/56/4, Eth1/57/1 Eth1/57/2, Eth1/57/3, Eth1/57/4 Eth1/58/1, Eth1/58/2, Eth1/58/3 Eth1/58/4, Eth1/59/1, Eth1/59/2 Eth1/59/3, Eth1/59/4, Eth1/60/1 Eth1/60/2, Eth1/60/3, Eth1/60/4 Eth1/61/1, Eth1/61/2, Eth1/61/3 Eth1/61/4, Eth1/62/1, Eth1/62/2 Eth1/62/3, Eth1/62/4 30 VLAN0030 active Eth1/1/1, Eth1/1/2, Eth1/1/3 Eth1/1/4, Eth1/2/1, Eth1/2/2 Eth1/2/3, Eth1/2/4, Eth1/3/1 Eth1/3/2, Eth1/3/3, Eth1/3/4 Eth1/4/1, Eth1/4/2, Eth1/4/3 Eth1/4/4, Eth1/5/1, Eth1/5/2 Eth1/5/3, Eth1/5/4, Eth1/6/1 Eth1/6/2, Eth1/6/3, Eth1/6/4 Eth1/7/1, Eth1/7/2, Eth1/7/3 Eth1/7/4, Eth1/8/1, Eth1/8/2 Eth1/8/3, Eth1/8/4, Eth1/9/1 Eth1/9/2, Eth1/9/3, Eth1/9/4 Eth1/10/1, Eth1/10/2, Eth1/10/3 Eth1/10/4, Eth1/11/1, Eth1/11/2 Eth1/11/3, Eth1/11/4, Eth1/12/1 Eth1/12/2, Eth1/12/3, Eth1/12/4 Eth1/13/1, Eth1/13/2, Eth1/13/3 Eth1/13/4, Eth1/14/1, Eth1/14/2 Eth1/14/3, Eth1/14/4, Eth1/15/1 Eth1/15/2, Eth1/15/3, Eth1/15/4 Eth1/16/1, Eth1/16/2, Eth1/16/3 Eth1/16/4, Eth1/17/1, Eth1/17/2 Eth1/17/3, Eth1/17/4, Eth1/18/1 Eth1/18/2, Eth1/18/3, Eth1/18/4 Eth1/19/1, Eth1/19/2, Eth1/19/3 Eth1/19/4, Eth1/20/1, Eth1/20/2 Eth1/20/3, Eth1/20/4, Eth1/21/1 Eth1/21/2, Eth1/21/3, Eth1/21/4 Eth1/22/1, Eth1/22/2, Eth1/22/3 Eth1/22/4, Eth1/23/1, Eth1/23/2 Eth1/23/3, Eth1/23/4, Eth1/24/1 Eth1/24/2, Eth1/24/3, Eth1/24/4 Eth1/25/1, Eth1/25/2, Eth1/25/3 Eth1/25/4, Eth1/26/1, Eth1/26/2 Eth1/26/3, Eth1/26/4, Eth1/27/1 Eth1/27/2, Eth1/27/3, Eth1/27/4 Eth1/28/1, Eth1/28/2, Eth1/28/3 Eth1/28/4, Eth1/29/1, Eth1/29/2 Eth1/29/3, Eth1/29/4, Eth1/30/1 Eth1/30/2, Eth1/30/3, Eth1/30/4 Eth1/31/1, Eth1/31/2, Eth1/31/3 Eth1/31/4, Eth1/32/1, Eth1/32/2 Eth1/32/3, Eth1/32/4, Eth1/33/1 Eth1/33/2, Eth1/33/3, Eth1/33/4 Eth1/34/1, Eth1/34/2, Eth1/34/3 Eth1/34/4, Eth1/35/1, Eth1/35/2 Eth1/35/3, Eth1/35/4, Eth1/36/1 Eth1/36/2, Eth1/36/3, Eth1/36/4 Eth1/37/1, Eth1/37/2, Eth1/37/3 Eth1/37/4, Eth1/38/1, Eth1/38/2 Eth1/38/3, Eth1/38/4, Eth1/39/1 Eth1/39/2, Eth1/39/3, Eth1/39/4 Eth1/40/1, Eth1/40/2, Eth1/40/3 Eth1/40/4, Eth1/41/1, Eth1/41/2 Eth1/41/3, Eth1/41/4, Eth1/42/1 Eth1/42/2, Eth1/42/3, Eth1/42/4 Eth1/43/1, Eth1/43/2, Eth1/43/3 Eth1/43/4, Eth1/44/1, Eth1/44/2 Eth1/44/3, Eth1/44/4, Eth1/45/1 Eth1/45/2, Eth1/45/3, Eth1/45/4 Eth1/46/1, Eth1/46/2, Eth1/46/3 Eth1/46/4, Eth1/47/1, Eth1/47/2 Eth1/47/3, Eth1/47/4, Eth1/48/1 Eth1/48/2, Eth1/48/3, Eth1/48/4 Eth1/49/1, Eth1/49/2, Eth1/49/3 Eth1/49/4, Eth1/50/1, Eth1/50/2 Eth1/50/3, Eth1/50/4, Eth1/51/1 Eth1/51/2, Eth1/51/3, Eth1/51/4 Eth1/52/1, Eth1/52/2, Eth1/52/3 Eth1/52/4, Eth1/53/1, Eth1/53/2 Eth1/53/3, Eth1/53/4, Eth1/54/1 Eth1/54/2, Eth1/54/3, Eth1/54/4 Eth1/55/1, Eth1/55/2, Eth1/55/3 Eth1/55/4, Eth1/56/1, Eth1/56/2 Eth1/56/3, Eth1/56/4, Eth1/57/1 Eth1/57/2, Eth1/57/3, Eth1/57/4 Eth1/58/1, Eth1/58/2, Eth1/58/3 Eth1/58/4, Eth1/59/1, Eth1/59/2 Eth1/59/3, Eth1/59/4, Eth1/60/1 Eth1/60/2, Eth1/60/3, Eth1/60/4 Eth1/61/1, Eth1/61/2, Eth1/61/3 Eth1/61/4, Eth1/62/1, Eth1/62/2 Eth1/62/3, Eth1/62/4 40 VLAN0040 active Eth1/1/1, Eth1/1/2, Eth1/1/3 Eth1/1/4, Eth1/2/1, Eth1/2/2 Eth1/2/3, Eth1/2/4, Eth1/3/1 Eth1/3/2, Eth1/3/3, Eth1/3/4 Eth1/4/1, Eth1/4/2, Eth1/4/3 Eth1/4/4, Eth1/5/1, Eth1/5/2 Eth1/5/3, Eth1/5/4, Eth1/6/1 Eth1/6/2, Eth1/6/3, Eth1/6/4 Eth1/7/1, Eth1/7/2, Eth1/7/3 Eth1/7/4, Eth1/8/1, Eth1/8/2 Eth1/8/3, Eth1/8/4, Eth1/9/1 Eth1/9/2, Eth1/9/3, Eth1/9/4 Eth1/10/1, Eth1/10/2, Eth1/10/3 Eth1/10/4, Eth1/11/1, Eth1/11/2 Eth1/11/3, Eth1/11/4, Eth1/12/1 Eth1/12/2, Eth1/12/3, Eth1/12/4 Eth1/13/1, Eth1/13/2, Eth1/13/3 Eth1/13/4, Eth1/14/1, Eth1/14/2 Eth1/14/3, Eth1/14/4, Eth1/15/1 Eth1/15/2, Eth1/15/3, Eth1/15/4 Eth1/16/1, Eth1/16/2, Eth1/16/3 Eth1/16/4, Eth1/17/1, Eth1/17/2 Eth1/17/3, Eth1/17/4, Eth1/18/1 Eth1/18/2, Eth1/18/3, Eth1/18/4 Eth1/19/1, Eth1/19/2, Eth1/19/3 Eth1/19/4, Eth1/20/1, Eth1/20/2 Eth1/20/3, Eth1/20/4, Eth1/21/1 Eth1/21/2, Eth1/21/3, Eth1/21/4 Eth1/22/1, Eth1/22/2, Eth1/22/3 Eth1/22/4, Eth1/23/1, Eth1/23/2 Eth1/23/3, Eth1/23/4, Eth1/24/1 Eth1/24/2, Eth1/24/3, Eth1/24/4 Eth1/25/1, Eth1/25/2, Eth1/25/3 Eth1/25/4, Eth1/26/1, Eth1/26/2 Eth1/26/3, Eth1/26/4, Eth1/27/1 Eth1/27/2, Eth1/27/3, Eth1/27/4 Eth1/28/1, Eth1/28/2, Eth1/28/3 Eth1/28/4, Eth1/29/1, Eth1/29/2 Eth1/29/3, Eth1/29/4, Eth1/30/1 Eth1/30/2, Eth1/30/3, Eth1/30/4 Eth1/31/1, Eth1/31/2, Eth1/31/3 Eth1/31/4, Eth1/32/1, Eth1/32/2 Eth1/32/3, Eth1/32/4, Eth1/33/1 Eth1/33/2, Eth1/33/3, Eth1/33/4 Eth1/34/1, Eth1/34/2, Eth1/34/3 Eth1/34/4, Eth1/35/1, Eth1/35/2 Eth1/35/3, Eth1/35/4, Eth1/36/1 Eth1/36/2, Eth1/36/3, Eth1/36/4 Eth1/37/1, Eth1/37/2, Eth1/37/3 Eth1/37/4, Eth1/38/1, Eth1/38/2 Eth1/38/3, Eth1/38/4, Eth1/39/1 Eth1/39/2, Eth1/39/3, Eth1/39/4 Eth1/40/1, Eth1/40/2, Eth1/40/3 Eth1/40/4, Eth1/41/1, Eth1/41/2 Eth1/41/3, Eth1/41/4, Eth1/42/1 Eth1/42/2, Eth1/42/3, Eth1/42/4 Eth1/43/1, Eth1/43/2, Eth1/43/3 Eth1/43/4, Eth1/44/1, Eth1/44/2 Eth1/44/3, Eth1/44/4, Eth1/45/1 Eth1/45/2, Eth1/45/3, Eth1/45/4 Eth1/46/1, Eth1/46/2, Eth1/46/3 Eth1/46/4, Eth1/47/1, Eth1/47/2 Eth1/47/3, Eth1/47/4, Eth1/48/1 Eth1/48/2, Eth1/48/3, Eth1/48/4 Eth1/49/1, Eth1/49/2, Eth1/49/3 Eth1/49/4, Eth1/50/1, Eth1/50/2 Eth1/50/3, Eth1/50/4, Eth1/51/1 Eth1/51/2, Eth1/51/3, Eth1/51/4 Eth1/52/1, Eth1/52/2, Eth1/52/3 Eth1/52/4, Eth1/53/1, Eth1/53/2 Eth1/53/3, Eth1/53/4, Eth1/54/1 Eth1/54/2, Eth1/54/3, Eth1/54/4 Eth1/55/1, Eth1/55/2, Eth1/55/3 Eth1/55/4, Eth1/56/1, Eth1/56/2 Eth1/56/3, Eth1/56/4, Eth1/57/1 Eth1/57/2, Eth1/57/3, Eth1/57/4 Eth1/58/1, Eth1/58/2, Eth1/58/3 Eth1/58/4, Eth1/59/1, Eth1/59/2 Eth1/59/3, Eth1/59/4, Eth1/60/1 Eth1/60/2, Eth1/60/3, Eth1/60/4 Eth1/61/1, Eth1/61/2, Eth1/61/3 Eth1/61/4, Eth1/62/1, Eth1/62/2 Eth1/62/3, Eth1/62/4 cs1# show interface trunk ----------------------------------------------------- Port Native Status Port Vlan Channel ----------------------------------------------------- Eth1/1/1 1 trunking -- Eth1/1/2 1 trunking -- Eth1/1/3 1 trunking -- Eth1/1/4 1 trunking -- Eth1/2/1 1 trunking -- Eth1/2/2 1 trunking -- Eth1/2/3 1 trunking -- Eth1/2/4 1 trunking -- . . . Eth1/62/2 none Eth1/62/3 none Eth1/62/4 none Eth1/63 none Eth1/64 none Po1 1
有关具体端口和 VLAN 使用详情，请参阅 RCF 中的横幅和重要说明部分。 -
验证 cs1 和 cs2 之间的 ISL 连接是否正常：
show port-channel summary显示示例
cs1# show port-channel summary Flags: D - Down P - Up in port-channel (members) I - Individual H - Hot-standby (LACP only) s - Suspended r - Module-removed b - BFD Session Wait S - Switched R - Routed U - Up (port-channel) p - Up in delay-lacp mode (member) M - Not in use. Min-links not met -------------------------------------------------------------------------------- Group Port- Type Protocol Member Ports Channel -------------------------------------------------------------------------------- 1 Po1(SU) Eth LACP Eth1/63(P) Eth1/64(P) 999 Po999(SD) Eth NONE -- cs1# -
确认集群 LIF 已恢复到其原端口：
network interface show -role cluster显示示例
cluster1::*> network interface show -role cluster Logical Status Network Current Current Is Vserver Interface Admin/Oper Address/Mask Node Port Home ----------- ------------------ ---------- ------------------ ------------ ------- ---- Cluster node1-01_clus1 up/up 169.254.36.44/16 node1-01 e7a true node1-01_clus2 up/up 169.254.7.5/16 node1-01 e7b true node1-02_clus1 up/up 169.254.197.206/16 node1-02 e7a true node1-02_clus2 up/up 169.254.195.186/16 node1-02 e7b true node1-03_clus1 up/up 169.254.192.49/16 node1-03 e7a true node1-03_clus2 up/up 169.254.182.76/16 node1-03 e7b true node1-04_clus1 up/up 169.254.59.49/16 node1-04 e7a true node1-04_clus2 up/up 169.254.62.244/16 node1-04 e7b true 8 entries were displayed.如果任何集群 LIF 尚未返回到其源端口，请从本地节点手动将其还原：
network interface revert -vserver vserver_name -lif <lif-name> -
验证集群是否运行正常：
cluster show显示示例
cluster1::*> cluster show Node Health Eligibility Epsilon ----------------- ------- ------------- ------- node1-01 true true false node1-02 true true false node1-03 true true true node1-04 true true false
-
验证远程集群接口的连接性：
-
你可以使用 `network interface check cluster-connectivity show`用于显示集群连接性可访问性检查详细信息的命令：
network interface check cluster-connectivity show显示示例
cluster1::*> network interface check cluster-connectivity show Source Destination Packet Node Date LIF LIF Loss ------ -------------------------- ---------------- --------------- ----------- node1-01 6/4/2025 03:13:33 -04:00 node1-01_clus2 node1-02_clus1 none 6/4/2025 03:13:34 -04:00 node1-01_clus2 node1-02_clus1 none node1-02 6/4/2025 03:13:33 -04:00 node1-02_clus2 node1-01_clus1 none 6/4/2025 03:13:34 -04:00 node1-02_clus2 node1-01_clus2 none . . . -
或者，您可以使用 `cluster ping-cluster -node <node-name>`检查连接性的命令：
cluster ping-cluster -node <node-name>
显示示例
cluster1::*> cluster ping-cluster -node local Host is node1-04 Getting addresses from network interface table... Cluster node1-01_clus1 169.254.36.44 node1-01 e7a Cluster node1-01_clus2 169.254.7.5 node1-01 e7b Cluster node1-02_clus1 169.254.197.206 node1-02 e7a Cluster node1-02_clus2 169.254.195.186 node1-02 e7b Cluster node1-03_clus1 169.254.192.49 node1-03 e7a Cluster node1-03_clus2 169.254.182.76 node1-03 e7b Cluster node1-04_clus1 169.254.59.49 node1-04 e7a Cluster node1-04_clus2 169.254.62.244 node1-04 e7b Local = 169.254.59.49 169.254.62.244 Remote = 169.254.36.44 169.254.7.5 169.254.197.206 169.254.195.186 169.254.192.49 169.254.182.76 Cluster Vserver Id = 4294967293 Ping status: ............ Basic connectivity succeeds on 12 path(s) Basic connectivity fails on 0 path(s) ................................................ Detected 9000 byte MTU on 12 path(s): Local 169.254.59.49 to Remote 169.254.182.76 Local 169.254.59.49 to Remote 169.254.192.49 Local 169.254.59.49 to Remote 169.254.195.186 Local 169.254.59.49 to Remote 169.254.197.206 Local 169.254.59.49 to Remote 169.254.36.44 Local 169.254.59.49 to Remote 169.254.7.5 Local 169.254.62.244 to Remote 169.254.182.76 Local 169.254.62.244 to Remote 169.254.192.49 Local 169.254.62.244 to Remote 169.254.195.186 Local 169.254.62.244 to Remote 169.254.197.206 Local 169.254.62.244 to Remote 169.254.36.44 Local 169.254.62.244 to Remote 169.254.7.5 Larger than PMTU communication succeeds on 12 path(s) RPC status: 6 paths up, 0 paths down (tcp check) 6 paths up, 0 paths down (udp check) -
下一步是什么？
升级 RCF 后，您"验证 SSH 配置"。