本繁體中文版使用機器翻譯，譯文僅供參考，若與英文版本牴觸，應以英文版本為準。
安裝或升級 NX-OS 軟體
貢獻者
建議變更
PDF
請依照下列步驟在 Nexus 9364D-GX2A 交換器上安裝或升級 NX-OS 軟體。
審查要求
開始之前
驗證以下內容：
-
完成該程式"準備安裝 NX-OS 和 RCF"。
-
交換器配置的目前備份可用。
-
一個功能齊全的叢集（日誌中沒有錯誤或類似問題）已經到位。
建議的文檔
-
請查閱交換器相容性表格，以了解支援的ONTAP和 NX-OS 版本。
-
有關Cisco交換器升級和降級程序的完整文檔，請參閱Cisco網站上提供的相應軟體和升級指南。
-
"Cisco Nexus 9000 和 3000 升級和 ISSU 矩陣"
根據您目前和目標版本，提供有關 Nexus 9000 系列交換器上Cisco NX-OS 軟體的中斷式升級/降級的資訊。
在頁面上，選擇“中斷式升級”，然後從下拉清單中選擇目前版本和目標版本。
關於範例
本流程中的範例使用以下開關和節點命名規則：
-
這兩個Cisco交換器的名稱分別是 cs1 和 cs2。
-
節點名稱為node1-01、node1-02、node1-03和node1-04。
-
群集 LIF 名稱稱為 node1-01_clus1、node1-01_clus2、node1-02_clus1、node1-02_clus2、node1-03_clus1、node1-03_clus2、node1-04_clus1 和 node1-04_clus2。
-
這 `cluster1::*>`prompt 指示叢集名稱。
安裝軟體
流程需要同時使用ONTAP指令和Cisco Nexus 9000 系列交換器指令；除非另有說明，否則使用ONTAP指令。
|
|
步驟
-
將交換器連接到管理網路。
-
使用 ping 指令驗證與託管 NX-OS 軟體和 RCF 的伺服器的連接性。
顯示範例
此範例驗證交換器可以存取 IP 位址為 172.19.2.1 的伺服器：
cs2# ping 172.19.2.1 Pinging 172.19.2.1 with 0 bytes of data: Reply From 172.19.2.1: icmp_seq = 0. time= 5910 usec.
-
顯示每個節點上連接到叢集交換器的叢集連接埠：
network device-discovery show顯示範例
cluster1::*> network device-discovery show Node/ Local Discovered Protocol Port Device (LLDP: ChassisID) Interface Platform ----------- ------ ------------------------ ---------------- ---------------- node1-01/cdp e10a cs1(FLMXXXXXXXX) Ethernet1/16/3 N9K-C9364D-GX2A e10b cs2(FDOXXXXXXXX) Ethernet1/13/3 N9K-C9364D-GX2A e11a cs1(FLMXXXXXXXX) Ethernet1/16/4 N9K-C9364D-GX2A e11b cs2(FDOXXXXXXXX) Ethernet1/13/4 N9K-C9364D-GX2A e1a cs1(FLMXXXXXXXX) Ethernet1/16/1 N9K-C9364D-GX2A e1b cs2(FDOXXXXXXXX) Ethernet1/13/1 N9K-C9364D-GX2A . . . e7a cs1(FLMXXXXXXXX) Ethernet1/16/2 N9K-C9364D-GX2A e7b cs2(FDOXXXXXXXX) Ethernet1/13/2 N9K-C9364D-GX2A node1-01/lldp e10a cs1 (c8:60:8f:xx:xx:xx) Ethernet1/16/3 - e10b cs2 (04:e3:87:xx:xx:xx) Ethernet1/13/3 - e11a cs1 (c8:60:8f:xx:xx:xx) Ethernet1/16/4 - e11b cs2 (04:e3:87:xx:xx:xx) Ethernet1/13/4 - e1a cs1 (c8:60:8f:xx:xx:xx) Ethernet1/16/1 - e1b cs2 (04:e3:87:xx:xx:xx) Ethernet1/13/1 - . . . e7a cs1 (c8:60:8f:xx:xx:xx) Ethernet1/16/2 - e7b cs2 (04:e3:87:xx:xx:xx) Ethernet1/13/2 - . . . -
檢查各港口的行政及營運狀況。
-
集群連接埠
-
確認叢集所有連接埠均已啟動且狀態正常：
network port show -ipspace Cluster顯示範例
cluster1::*> network port show -ipspace Cluster Node: node1-01 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ----------- -------- ------ e7a Cluster Cluster up 9000 auto/100000 healthy false e7b Cluster Cluster up 9000 auto/100000 healthy false Node: node1-02 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ----------- -------- ------ e7a Cluster Cluster up 9000 auto/100000 healthy false e7b Cluster Cluster up 9000 auto/100000 healthy false Node: node1-03 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ----------- -------- ------ e7a Cluster Cluster up 9000 auto/10000 healthy false e7b Cluster Cluster up 9000 auto/10000 healthy false Node: node1-04 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ----------- -------- ------ e7a Cluster Cluster up 9000 auto/10000 healthy false e7b Cluster Cluster up 9000 auto/10000 healthy false -
確認所有叢集介面（LIF）都位於主連接埠上：
network interface show -role cluster顯示範例
cluster1::*> network interface show -role cluster Logical Status Network Current Current Is Vserver Interface Admin/Oper Address/Mask Node Port Home ----------- --------------- ---------- ------------------ --------- ------- ---- Cluster node1-01_clus1 up/up 169.254.36.44/16 node1-01 e7a true node1-01_clus2 up/up 169.254.7.5/16 node1-01 e7b true node1-02_clus1 up/up 169.254.197.206/16 node1-02 e7a true node1-02_clus2 up/up 169.254.195.186/16 node1-02 e7b true node1-03_clus1 up/up 169.254.192.49/16 node1-03 e7a true node1-03_clus2 up/up 169.254.182.76/16 node1-03 e7b true node1-04_clus1 up/up 169.254.59.49/16 node1-04 e7a true node1-04_clus2 up/up 169.254.62.244/16 node1-04 e7b true 8 entries were displayed. -
確認集群顯示兩個集群交換器的資訊：
system cluster-switch show -is-monitoring-enabled-operational true顯示範例
cluster1::*> system cluster-switch show -is-monitoring-enabled-operational true Switch Type Address Model --------------------------- ------------------ ---------------- --------------- cs2(FDOXXXXXXXX) cluster-network 10.228.137.233 N9K-C9364D-GX2A Serial Number: FDOXXXXXXXX Is Monitored: true Reason: None Software Version: Cisco Nexus Operating System (NX-OS) Software, Version 10.4(2) Version Source: CDP/ISDP cs1(FLMXXXXXXXX) cluster-network 10.228.137.253 N9K-C9364D-GX2A Serial Number: FLMXXXXXXXX Is Monitored: true Reason: None Software Version: Cisco Nexus Operating System (NX-OS) Software, Version 10.4(2) Version Source: CDP/ISDP 2 entries were displayed.
-
-
HA 連接埠
-
驗證所有 HA 連接埠是否處於正常運作狀態：
ha interconnect status show -node <node-name>
-
顯示範例
cluster1::*> ha interconnect status show -node node1-01 (system ha interconnect status show) Node: node1-01 Link 0 Status: up Link 1 Status: up Is Link 0 Active: true Is Link 1 Active: true IC RDMA Connection: up Slot: 0 Debug Firmware: no Interconnect Port 0 : Port Name: e1a-17 MTU: 4096 Link Information: ACTIVE Interconnect Port 1 : Port Name: e1b-18 MTU: 4096 Link Information: ACTIVE cluster1::*> ha interconnect status show -node node1-02 (system ha interconnect status show) Node: node1-02 Link 0 Status: up Link 1 Status: up Is Link 0 Active: true Is Link 1 Active: true IC RDMA Connection: up Slot: 0 Debug Firmware: no Interconnect Port 0 : Port Name: e1a-17 MTU: 4096 Link Information: ACTIVE Interconnect Port 1 : Port Name: e1b-18 MTU: 4096 Link Information: ACTIVE . . .-
儲存連接埠
-
驗證所有儲存連接埠均處於正常狀態：
storage port show -port-type ENET顯示範例
cluster1::*> storage port show -port-type ENET Speed Node Port Type Mode (Gb/s) State Status ------------------ ---- ----- ------- ------ -------- ----------- node1-01 e10a ENET - 100 enabled online e10b ENET - 100 enabled online e11a ENET - 100 enabled online e11b ENET - 100 enabled online node1-02 e10a ENET - 100 enabled online e10b ENET - 100 enabled online e11a ENET - 100 enabled online e11b ENET - 100 enabled online node1-03 e10a ENET - 100 enabled online e10b ENET - 100 enabled online e11a ENET - 100 enabled online node1-04 e10a ENET - 100 enabled online e10b ENET - 100 enabled online e11a ENET - 100 enabled online e11b ENET - 100 enabled online 16 entries were displayed.
-
-
儲存架連接埠
-
驗證所有儲存架連接埠是否處於正常狀態：
storage shelf port show顯示範例
cluster1::*> storage shelf port show Shelf ID Module State Internal? ----- -- ------ ------------ --------- 1.1 0 A connected false 1 A connected false 2 A connected false 3 A connected false 4 A connected false 5 A connected false 6 A connected false 7 A connected false 8 B connected false 9 B connected false 10 B connected false 11 B connected false 12 B connected false 13 B connected false 14 B connected false 15 B connected false 16 entries were displayed. -
驗證所有儲存架連接埠的連線狀態：
storage shelf port show -fields remote-device,remote-port,connector-state顯示範例
cluster1::*> storage shelf port show -fields remote-device,remote-port,connector-state shelf id connector-state remote-port remote-device ----- -- --------------- -------------- ----------------- 1.1 0 connected Ethernet1/17/1 CX9332D-cs1 1.1 1 connected Ethernet1/15/1 CX9364D-cs1 1.1 2 connected Ethernet1/17/2 CX9332D-cs1 1.1 3 connected Ethernet1/15/2 CX9364D-cs1 1.1 4 connected Ethernet1/17/3 CX9332D-cs1 1.1 5 connected Ethernet1/15/3 CX9364D-cs1 1.1 6 connected Ethernet1/17/4 CX9332D-cs1 1.1 7 connected Ethernet1/15/4 CX9364D-cs1 1.1 8 connected Ethernet1/19/1 CX9332D-cs1 1.1 9 connected Ethernet1/17/1 CX9364D-cs1 1.1 10 connected Ethernet1/19/2 CX9332D-cs1 1.1 11 connected Ethernet1/17/2 CX9364D-cs1 1.1 12 connected Ethernet1/19/3 CX9332D-cs1 1.1 13 connected Ethernet1/17/3 CX9364D-cs1 1.1 14 connected Ethernet1/19/4 CX9332D-cs1 1.1 15 connected Ethernet1/17/4 CX9364D-cs1 16 entries were displayed.
-
-
-
停用群集 LIF 的自動回滾功能。叢集 LIF 會故障轉移到夥伴叢集交換機，並在您對目標交換器執行升級程序時保留在該交換器上：
network interface modify -vserver Cluster -lif * -auto-revert false -
將 NX-OS 軟體和 EPLD 映像複製到 Nexus 9364D-GX2A 交換器。
顯示範例
cs2# copy sftp: bootflash: vrf management Enter source filename: /code/nxos.10.4.2.bin Enter hostname for the sftp server: 172.19.2.1 Enter username: root Outbound-ReKey for 172.19.2.1:22 Inbound-ReKey for 172.19.2.1:22 root@172.19.2.1's password: sftp> progress Progress meter enabled sftp> get /code/nxos.10.4.2.bin /bootflash/nxos.10.4.2.bin /code/nxos.10.4.2.bin 100% 1261MB 9.3MB/s 02:15 sftp> exit Copy complete, now saving to disk (please wait)... Copy complete. cs2# copy sftp: bootflash: vrf management Enter source filename: /code/n9000-epld.10.4.2.F.img Enter hostname for the sftp server: 172.19.2.1 Enter username: user1 Outbound-ReKey for 172.19.2.1:22 Inbound-ReKey for 172.19.2.1:22 user1@172.19.2.1's password: sftp> progress Progress meter enabled sftp> get /code/n9000-epld.10.4.2.F.img /bootflash/n9000-epld.10.4.2.F.img /code/n9000-epld.10.4.2.F.img 100% 161MB 9.5MB/s 00:16 sftp> exit Copy complete, now saving to disk (please wait)... Copy complete.
-
請確認NX-OS軟體的運作版本：
show version顯示範例
cs2# show version Cisco Nexus Operating System (NX-OS) Software TAC support: http://www.cisco.com/tac Copyright (C) 2002-2025, Cisco and/or its affiliates. All rights reserved. The copyrights to certain works contained in this software are owned by other third parties and used and distributed under their own licenses, such as open source. This software is provided "as is," and unless otherwise stated, there is no warranty, express or implied, including but not limited to warranties of merchantability and fitness for a particular purpose. Certain components of this software are licensed under the GNU General Public License (GPL) version 2.0 or GNU General Public License (GPL) version 3.0 or the GNU Lesser General Public License (LGPL) Version 2.1 or Lesser General Public License (LGPL) Version 2.0. A copy of each such license is available at http://www.opensource.org/licenses/gpl-2.0.php and http://opensource.org/licenses/gpl-3.0.html and http://www.opensource.org/licenses/lgpl-2.1.php and http://www.gnu.org/licenses/old-licenses/library.txt. Software BIOS: version 01.14 NXOS: version 10.4(1) [Feature Release] Host NXOS: version 10.4(1) BIOS compile time: 11/25/2024 NXOS image file is: bootflash:///nxos64-cs.10.4.1.F.bin NXOS compile time: 11/30/2023 12:00:00 [12/14/2023 05:25:50] NXOS boot mode: LXC Hardware cisco Nexus9000 C9332D-GX2B Chassis Intel(R) Xeon(R) CPU D-1633N @ 2.50GHz with 32802156 kB of memory. Processor Board ID FLMXXXXXXXX Device name: cs2 bootflash: 115802886 kB Kernel uptime is 5 day(s), 2 hour(s), 13 minute(s), 21 second(s) Last reset at 3580 usecs after Thu Jun 5 15:55:08 2025 Reason: Reset Requested by CLI command reload System version: 10.4(1) Service: plugin Core Plugin, Ethernet Plugin Active Package(s): cs2#
-
安裝 NX-OS 鏡像。
安裝鏡像檔案後，每次交換器重新啟動時都會載入該檔案。
顯示範例
cs2# install all nxos bootflash:nxos.10.4.2.bin Installer will perform compatibility check first. Please wait. Installer is forced disruptive Verifying image bootflash:/nxos.10.4.2.bin for boot variable "nxos". [] 100% -- SUCCESS Verifying image type. [] 100% -- SUCCESS Preparing "nxos" version info using image bootflash:/nxos.10.4.2.bin. [] 100% -- SUCCESS Preparing "bios" version info using image bootflash:/nxos.10.4.2.bin. [] 100% -- SUCCESS Performing module support checks. [] 100% -- SUCCESS Notifying services about system upgrade. [] 100% -- SUCCESS Compatibility check is done: Module Bootable Impact Install-type Reason ------ -------- --------------- ------------ --------- 1 yes Disruptive Reset Default upgrade is not hitless Images will be upgraded according to following table: Module Image Running-Version(pri:alt) New-Version Upg-Required ------- --------- ---------------------------------------- ------------------- ------------ 1 nxos 10.4(1) 10.4(2) Yes 1 bios xx.xx.:xx.xx xxx No Switch will be reloaded for disruptive upgrade. Do you want to continue with the installation (y/n)? [n] y Install is in progress, please wait. Performing runtime checks. [] 100% -- SUCCESS Setting boot variables. [] 100% -- SUCCESS Performing configuration copy. [] 100% -- SUCCESS Module 1: Refreshing compact flash and upgrading bios/loader/bootrom. Warning: please do not remove or power off the module at this time. [] 100% -- SUCCESS Finishing the upgrade, switch will reboot in 10 seconds.
-
交換器重新啟動後，請先驗證NX-OS軟體的新版本：
show version顯示範例
cs2# show version Cisco Nexus Operating System (NX-OS) Software TAC support: http://www.cisco.com/tac Copyright (C) 2002-2025, Cisco and/or its affiliates. All rights reserved. The copyrights to certain works contained in this software are owned by other third parties and used and distributed under their own licenses, such as open source. This software is provided "as is," and unless otherwise stated, there is no warranty, express or implied, including but not limited to warranties of merchantability and fitness for a particular purpose. Certain components of this software are licensed under the GNU General Public License (GPL) version 2.0 or GNU General Public License (GPL) version 3.0 or the GNU Lesser General Public License (LGPL) Version 2.1 or Lesser General Public License (LGPL) Version 2.0. A copy of each such license is available at http://www.opensource.org/licenses/gpl-2.0.php and http://opensource.org/licenses/gpl-3.0.html and http://www.opensource.org/licenses/lgpl-2.1.php and http://www.gnu.org/licenses/old-licenses/library.txt. Software BIOS: version 01.14 NXOS: version 10.4(2) [Feature Release] Host NXOS: version 10.4(2) BIOS compile time: 11/25/2024 NXOS image file is: bootflash:///nxos64-cs.10.4.2.F.bin NXOS compile time: 11/30/2023 12:00:00 [12/14/2023 05:25:50] NXOS boot mode: LXC Hardware cisco Nexus9000 C9332D-GX2B Chassis Intel(R) Xeon(R) CPU D-1633N @ 2.50GHz with 32802156 kB of memory. Processor Board ID FLMXXXXXXXX Device name: cs2 bootflash: 115802886 kB Kernel uptime is 5 day(s), 2 hour(s), 13 minute(s), 21 second(s) Last reset at 3580 usecs after Thu Jun 5 15:55:08 2025 Reason: Reset Requested by CLI command reload System version: 10.4(2) Service: plugin Core Plugin, Ethernet Plugin Active Package(s): cs2#
-
升級EPLD鏡像並重新啟動交換器。
顯示範例
cs2# show version module 1 epld EPLD Device Version --------------------------------------- MI FPGA 0x7 IO FPGA 0x17 MI FPGA2 0x2 GEM FPGA 0x2 GEM FPGA 0x2 GEM FPGA 0x2 GEM FPGA 0x2 cs2# install epld bootflash:n9000-epld.10.4.2.F.img module all Compatibility check: Module Type Upgradable Impact Reason ------ ------------------ ----------------- --------- ----------- 1 SUP Yes disruptive Module Upgradable Retrieving EPLD versions.... Please wait. Images will be upgraded according to following table: Module Type EPLD Running-Version New-Version Upg-Required ------- ------ ----------------- ----------------- ------------ ------------ 1 SUP MI FPGA 0x07 0x07 No 1 SUP IO FPGA 0x17 0x19 Yes 1 SUP MI FPGA2 0x02 0x02 No The above modules require upgrade. The switch will be reloaded at the end of the upgrade Do you want to continue (y/n) ? [n] y Proceeding to upgrade Modules. Starting Module 1 EPLD Upgrade Module 1 : IO FPGA [Programming] : 100.00% ( 64 of 64 sectors) Module 1 EPLD upgrade is successful. Module Type Upgrade-Result -------- ----- -------------- 1 SUP Success EPLDs upgraded. Module 1 EPLD upgrade is successful. -
交換器重新啟動後，再次登入並驗證新版本的 EPLD 是否已成功載入。
顯示範例
cs2# show version module 1 epld EPLD Device Version --------------------------------------- MI FPGA 0x7 IO FPGA 0x19 MI FPGA2 0x2 GEM FPGA 0x2 GEM FPGA 0x2 GEM FPGA 0x2 GEM FPGA 0x2
-
驗證叢集上所有連接埠的健康狀況。
-
集群連接埠
-
確認叢集中所有節點的叢集連接埠均已啟動且運作狀況良好：
network port show -ipspace Cluster顯示範例
cluster1::*> network port show -ipspace Cluster Node: node1-01 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ----------- -------- ------ e7a Cluster Cluster up 9000 auto/10000 healthy false e7b Cluster Cluster up 9000 auto/10000 healthy false Node: node1-02 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ----------- -------- ------ e7a Cluster Cluster up 9000 auto/10000 healthy false e7b Cluster Cluster up 9000 auto/10000 healthy false Node: node1-03 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ----------- -------- ------ e7a Cluster Cluster up 9000 auto/100000 healthy false e7b Cluster Cluster up 9000 auto/100000 healthy false Node: node1-04 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ----------- -------- ------ e7a Cluster Cluster up 9000 auto/100000 healthy false e7b Cluster Cluster up 9000 auto/100000 healthy false -
從叢集驗證交換器運作狀況：
network device-discovery show -protocol cdpsystem cluster-switch show -is-monitoring-enabled-operational true顯示範例
cluster1::*> network device-discovery show -protocol cdp node1-01/cdp e10a cs1(FLMXXXXXXXX) Ethernet1/16/3 N9K-C9364D-GX2A e10b cs2(FDOXXXXXXXX) Ethernet1/13/3 N9K-C9364D-GX2A e11a cs1(FLMXXXXXXXX) Ethernet1/16/4 N9K-C9364D-GX2A e11b cs2(FDOXXXXXXXX) Ethernet1/13/4 N9K-C9364D-GX2A e1a cs1(FLMXXXXXXXX) Ethernet1/16/1 N9K-C9364D-GX2A e1b cs2(FDOXXXXXXXX) Ethernet1/13/1 N9K-C9364D-GX2A . . . e7a cs1(FLMXXXXXXXX) Ethernet1/16/2 N9K-C9364D-GX2A e7b cs2(FDOXXXXXXXX) Ethernet1/13/2 N9K-C9364D-GX2A node1-02/cdp e10a cs1(FLMXXXXXXXX) Ethernet1/16/3 N9K-C9364D-GX2A e10b cs2(FDOXXXXXXXX) Ethernet1/13/3 N9K-C9364D-GX2A e11a cs1(FLMXXXXXXXX) Ethernet1/16/4 N9K-C9364D-GX2A e11b cs2(FDOXXXXXXXX) Ethernet1/13/4 N9K-C9364D-GX2A e1a cs1(FLMXXXXXXXX) Ethernet1/16/1 N9K-C9364D-GX2A e1b cs2(FDOXXXXXXXX) Ethernet1/13/1 N9K-C9364D-GX2A . . . e7a cs1(FLMXXXXXXXX) Ethernet1/16/2 N9K-C9364D-GX2A e7b cs2(FDOXXXXXXXX) Ethernet1/13/2 N9K-C9364D-GX2A . . . cluster1::*> system cluster-switch show -is-monitoring-enabled-operational true Switch Type Address Model --------------------------- ------------------ ---------------- --------------- cs2(FDOXXXXXXXX) cluster-network 10.228.137.233 N9K-C9364D-GX2A Serial Number: FDOXXXXXXXX Is Monitored: true Reason: None Software Version: Cisco Nexus Operating System (NX-OS) Software, Version 10.4(2) Version Source: CDP/ISDP cs1(FLMXXXXXXXX) cluster-network 10.228.137.253 N9K-C9364D-GX2A Serial Number: FLMXXXXXXXX Is Monitored: true Reason: None Software Version: Cisco Nexus Operating System (NX-OS) Software, Version 10.4(2) Version Source: CDP/ISDP
-
-
HA 連接埠
-
驗證所有 HA 連接埠是否處於正常運作狀態：
ha interconnect status show -node <node-name>
-
顯示範例
cluster1::*> ha interconnect status show -node node1-01 (system ha interconnect status show) Node: node1-01 Link 0 Status: up Link 1 Status: up Is Link 0 Active: true Is Link 1 Active: true IC RDMA Connection: up Slot: 0 Debug Firmware: no Interconnect Port 0 : Port Name: e1a-17 MTU: 4096 Link Information: ACTIVE Interconnect Port 1 : Port Name: e1b-18 MTU: 4096 Link Information: ACTIVE cluster1::*> ha interconnect status show -node node1-02 (system ha interconnect status show) Node: node1-02 Link 0 Status: up Link 1 Status: up Is Link 0 Active: true Is Link 1 Active: true IC RDMA Connection: up Slot: 0 Debug Firmware: no Interconnect Port 0 : Port Name: e1a-17 MTU: 4096 Link Information: ACTIVE Interconnect Port 1 : Port Name: e1b-18 MTU: 4096 Link Information: ACTIVE . . .-
儲存連接埠
-
驗證所有儲存連接埠均處於正常狀態：
storage port show -port-type ENET顯示範例
cluster1::*> storage port show -port-type ENET Speed Node Port Type Mode (Gb/s) State Status ------------------ ---- ----- ------- ------ -------- ----------- node1-01 e10a ENET - 100 enabled online e10b ENET - 100 enabled online e11a ENET - 100 enabled online e11b ENET - 100 enabled online node1-02 e10a ENET - 100 enabled online e10b ENET - 100 enabled online e11a ENET - 100 enabled online e11b ENET - 100 enabled online node1-03 e10a ENET - 100 enabled online e10b ENET - 100 enabled online e11a ENET - 100 enabled online node1-04 e10a ENET - 100 enabled online e10b ENET - 100 enabled online e11a ENET - 100 enabled online e11b ENET - 100 enabled online 16 entries were displayed.
-
-
儲存架連接埠
-
驗證所有儲存架連接埠是否處於正常狀態：
storage shelf port show顯示範例
cluster1::*> storage shelf port show Shelf ID Module State Internal? ----- -- ------ ------------ --------- 1.1 0 A connected false 1 A connected false 2 A connected false 3 A connected false 4 A connected false 5 A connected false 6 A connected false 7 A connected false 8 B connected false 9 B connected false 10 B connected false 11 B connected false 12 B connected false 13 B connected false 14 B connected false 15 B connected false 16 entries were displayed. -
驗證所有儲存架連接埠的連線狀態：
storage shelf port show -fields remote-device,remote-port,connector-state顯示範例
cluster1::*> storage shelf port show -fields remote-device,remote-port,connector-state shelf id connector-state remote-port remote-device ----- -- --------------- -------------- ----------------- 1.1 0 connected Ethernet1/17/1 CX9332D-cs1 1.1 1 connected Ethernet1/15/1 CX9364D-cs1 1.1 2 connected Ethernet1/17/2 CX9332D-cs1 1.1 3 connected Ethernet1/15/2 CX9364D-cs1 1.1 4 connected Ethernet1/17/3 CX9332D-cs1 1.1 5 connected Ethernet1/15/3 CX9364D-cs1 1.1 6 connected Ethernet1/17/4 CX9332D-cs1 1.1 7 connected Ethernet1/15/4 CX9364D-cs1 1.1 8 connected Ethernet1/19/1 CX9332D-cs1 1.1 9 connected Ethernet1/17/1 CX9364D-cs1 1.1 10 connected Ethernet1/19/2 CX9332D-cs1 1.1 11 connected Ethernet1/17/2 CX9364D-cs1 1.1 12 connected Ethernet1/19/3 CX9332D-cs1 1.1 13 connected Ethernet1/17/3 CX9364D-cs1 1.1 14 connected Ethernet1/19/4 CX9332D-cs1 1.1 15 connected Ethernet1/17/4 CX9364D-cs1 16 entries were displayed.
-
-
-
驗證叢集是否運作正常：
cluster show顯示範例
cluster1::*> cluster show Node Health Eligibility Epsilon -------------------- ------- ------------ ------------ node1-01 true true false node1-02 true true false node1-03 true true false node1-04 true true true 4 entries were displayed.
-
重複步驟 6 至 13，在交換器 cs1 上安裝 NX-OS 軟體。
-
啟用叢集 LIF 的自動回滾功能。
network interface modify -vserver Cluster -lif * -auto-revert true -
確認叢集 LIF 已恢復到其原始連接埠：
network interface show -role cluster顯示範例
cluster1::*> network interface show -role cluster Logical Status Network Current Current Is Vserver Interface Admin/Oper Address/Mask Node Port Home ----------- --------------- ---------- ------------------ ----------- ------- ---- Cluster node1-01_clus1 up/up 169.254.36.44/16 node1-01 e7a true node1-01_clus2 up/up 169.254.7.5/16 node1-01 e7b true node1-02_clus1 up/up 169.254.197.206/16 node1-02 e7a true node1-02_clus2 up/up 169.254.195.186/16 node1-02 e7b true node1-03_clus1 up/up 169.254.192.49/16 node1-03 e7a true node1-03_clus2 up/up 169.254.182.76/16 node1-03 e7b true node1-04_clus1 up/up 169.254.59.49/16 node1-04 e7a true node1-04_clus2 up/up 169.254.62.244/16 node1-04 e7b true如果任何叢集 LIF 尚未返回其來源端口，請從本機節點手動將其還原：
network interface revert -vserver Cluster -lif <lif-name>
下一步是什麼？
安裝或升級 NX-OS 軟體後，您"安裝或升級參考設定檔（RCF）"。