Skip to main content
Die deutsche Sprachversion wurde als Serviceleistung für Sie durch maschinelle Übersetzung erstellt. Bei eventuellen Unstimmigkeiten hat die englische Sprachversion Vorrang.

Installieren Sie die NX-OS-Software

Beitragende netapp-yvonneo netapp-jolieg
PDFs

Mit diesem Verfahren können Sie die NX-OS-Software auf dem Nexus 3232C Cluster-Switch installieren.

Überprüfungsanforderungen

Bevor Sie beginnen

  • Eine aktuelle Sicherungskopie der Switch-Konfiguration.

  • Ein voll funktionsfähiger Cluster (keine Fehler in den Protokollen oder ähnliche Probleme).

  • "Cisco Ethernet-Switch-Seite". In der Switch-Kompatibilitätstabelle finden Sie die unterstützten ONTAP und NX-OS-Versionen.

  • "Cisco Nexus 3000 Series Switches". Die vollständige Dokumentation zu den Upgrade- und Downgrade-Verfahren für Cisco -Switches finden Sie in den entsprechenden Software- und Upgrade-Anleitungen auf der Cisco -Website.

Installieren Sie die Software

Für dieses Verfahren werden sowohl ONTAP -Befehle als auch Cisco Nexus 3000 Series Switches-Befehle benötigt; es werden ONTAP -Befehle verwendet, sofern nicht anders angegeben.

Stellen Sie sicher, dass Sie den Vorgang abschließen in"Bereiten Sie die Installation von NX-OS und RCF vor." Befolgen Sie anschließend die folgenden Schritte.

Schritte

  1. Verbinden Sie den Cluster-Switch mit dem Management-Netzwerk.

  2. Verwenden Sie die ping Befehl zum Überprüfen der Verbindung zum Server, auf dem die NX-OS-Software und die RCF gehostet werden.

    Beispiel anzeigen

    Dieses Beispiel bestätigt, dass der Switch den Server unter der IP-Adresse 172.19.2.1 erreichen kann:

    cs2# ping 172.19.2.1
Pinging 172.19.2.1 with 0 bytes of data:

Reply From 172.19.2.1: icmp_seq = 0. time= 5910 usec.

  3. Zeigen Sie die Cluster-Ports auf jedem Knoten an, die mit den Cluster-Switches verbunden sind:

    network device-discovery show

    Beispiel anzeigen 
    cluster1::*> network device-discovery show
Node/       Local  Discovered
Protocol    Port   Device (LLDP: ChassisID)  Interface         Platform
----------- ------ ------------------------- ----------------  ----------
cluster1-01/cdp
            e0a    cs1                       Ethernet1/7       N3K-C3232C
            e0d    cs2                       Ethernet1/7       N3K-C3232C
cluster1-02/cdp
            e0a    cs1                       Ethernet1/8       N3K-C3232C
            e0d    cs2                       Ethernet1/8       N3K-C3232C
cluster1-03/cdp
            e0a    cs1                       Ethernet1/1/1     N3K-C3232C
            e0b    cs2                       Ethernet1/1/1     N3K-C3232C
cluster1-04/cdp
            e0a    cs1                       Ethernet1/1/2     N3K-C3232C
            e0b    cs2                       Ethernet1/1/2     N3K-C3232C
cluster1::*>

  4. Überprüfen Sie den administrativen und operativen Status jedes Cluster-Ports.

    1. Überprüfen Sie, ob alle Cluster-Ports aktiv sind und einen fehlerfreien Status aufweisen:

      network port show -role cluster

      Beispiel anzeigen 
      cluster1::*> network port show -role cluster

Node: cluster1-01
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e0a       Cluster      Cluster          up   9000  auto/100000 healthy false
e0d       Cluster      Cluster          up   9000  auto/100000 healthy false

Node: cluster1-02
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e0a       Cluster      Cluster          up   9000  auto/100000 healthy false
e0d       Cluster      Cluster          up   9000  auto/100000 healthy false
8 entries were displayed.

Node: cluster1-03

   Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e0a       Cluster      Cluster          up   9000  auto/10000 healthy  false
e0b       Cluster      Cluster          up   9000  auto/10000 healthy  false

Node: cluster1-04
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e0a       Cluster      Cluster          up   9000  auto/10000 healthy  false
e0b       Cluster      Cluster          up   9000  auto/10000 healthy  false
cluster1::*>

    2. Überprüfen Sie, ob alle Cluster-Schnittstellen (LIFs) am Home-Port angeschlossen sind:

      network interface show -role cluster

      Beispiel anzeigen 
      cluster1::*> network interface show -role cluster
            Logical            Status     Network           Current      Current Is
Vserver     Interface          Admin/Oper Address/Mask      Node         Port    Home
----------- ------------------ ---------- ----------------- ------------ ------- ----
Cluster
            cluster1-01_clus1  up/up     169.254.3.4/23     cluster1-01  e0a     true
            cluster1-01_clus2  up/up     169.254.3.5/23     cluster1-01  e0d     true
            cluster1-02_clus1  up/up     169.254.3.8/23     cluster1-02  e0a     true
            cluster1-02_clus2  up/up     169.254.3.9/23     cluster1-02  e0d     true
            cluster1-03_clus1  up/up     169.254.1.3/23     cluster1-03  e0a     true
            cluster1-03_clus2  up/up     169.254.1.1/23     cluster1-03  e0b     true
            cluster1-04_clus1  up/up     169.254.1.6/23     cluster1-04  e0a     true
            cluster1-04_clus2  up/up     169.254.1.7/23     cluster1-04  e0b     true
8 entries were displayed.
cluster1::*>

    3. Überprüfen Sie, ob der Cluster Informationen für beide Cluster-Switches anzeigt:

      system cluster-switch show -is-monitoring-enabled-operational true

    Beispiel anzeigen 
    cluster1::*> system cluster-switch show -is-monitoring-enabled-operational true
Switch                      Type               Address          Model
--------------------------- ------------------ ---------------- ----------
cs1                         cluster-network    10.233.205.90    N3K-C3232C
     Serial Number: FOCXXXXXXGD
      Is Monitored: true
            Reason: None
  Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                    9.3(5)
    Version Source: CDP

cs2                         cluster-network    10.233.205.91    N3K-C3232C
     Serial Number: FOCXXXXXXGS
      Is Monitored: true
            Reason: None
  Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                    9.3(5)
    Version Source: CDP
cluster1::*>

  5. Automatische Wiederherstellung der Cluster-LIFs deaktivieren. Die Cluster-LIFs wechseln zum Partner-Cluster-Switch und bleiben dort, während Sie das Upgrade-Verfahren auf dem Ziel-Switch durchführen:

    network interface modify -vserver Cluster -lif * -auto-revert false

  6. Kopieren Sie die NX-OS-Software und die EPLD-Images auf den Nexus 3232C-Switch.

    Beispiel anzeigen 
    cs2# copy sftp: bootflash: vrf management
Enter source filename: /code/nxos.9.3.4.bin
Enter hostname for the sftp server: 172.19.2.1
Enter username: user1

Outbound-ReKey for 172.19.2.1:22
Inbound-ReKey for 172.19.2.1:22
user1@172.19.2.1's password:
sftp> progress
Progress meter enabled
sftp> get   /code/nxos.9.3.4.bin  /bootflash/nxos.9.3.4.bin
/code/nxos.9.3.4.bin  100% 1261MB   9.3MB/s   02:15
sftp> exit
Copy complete, now saving to disk (please wait)...
Copy complete.


cs2# copy sftp: bootflash: vrf management
Enter source filename: /code/n9000-epld.9.3.4.img
Enter hostname for the sftp server: 172.19.2.1
Enter username: user1

Outbound-ReKey for 172.19.2.1:22
Inbound-ReKey for 172.19.2.1:22
user1@172.19.2.1's password:
sftp> progress
Progress meter enabled
sftp> get   /code/n9000-epld.9.3.4.img  /bootflash/n9000-epld.9.3.4.img
/code/n9000-epld.9.3.4.img  100%  161MB   9.5MB/s   00:16
sftp> exit
Copy complete, now saving to disk (please wait)...
Copy complete.

  7. Überprüfen Sie die laufende Version der NX-OS-Software:

    show version

    Beispiel anzeigen 
    cs2# show version
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (C) 2002-2019, Cisco and/or its affiliates.
All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under their own
licenses, such as open source.  This software is provided "as is," and unless
otherwise stated, there is no warranty, express or implied, including but not
limited to warranties of merchantability and fitness for a particular purpose.
Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or
GNU General Public License (GPL) version 3.0  or the GNU
Lesser General Public License (LGPL) Version 2.1 or
Lesser General Public License (LGPL) Version 2.0.
A copy of each such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://opensource.org/licenses/gpl-3.0.html and
http://www.opensource.org/licenses/lgpl-2.1.php and
http://www.gnu.org/licenses/old-licenses/library.txt.

Software
  BIOS: version 08.37
  NXOS: version 9.3(3)
  BIOS compile time:  01/28/2020
  NXOS image file is: bootflash:///nxos.9.3.3.bin
  NXOS compile time:  12/22/2019 2:00:00 [12/22/2019 14:00:37]

Hardware
  cisco Nexus3000 C3232C Chassis (Nexus 9000 Series)
  Intel(R) Xeon(R) CPU E5-2403 v2 @ 1.80GHz with 8154432 kB of memory.
  Processor Board ID FOCXXXXXXGD

  Device name: cs2
  bootflash:   53298520 kB
Kernel uptime is 0 day(s), 0 hour(s), 3 minute(s), 36 second(s)

Last reset at 74117 usecs after Tue Nov 24 06:24:23 2020
  Reason: Reset Requested by CLI command reload
  System version: 9.3(3)
  Service:

plugin
  Core Plugin, Ethernet Plugin

Active Package(s):

cs2#

  8. Installieren Sie das NX-OS-Image.

    Durch die Installation der Image-Datei wird diese bei jedem Neustart des Switches geladen.

    Beispiel anzeigen 
    cs2# install all nxos bootflash:nxos.9.3.4.bin
Installer will perform compatibility check first. Please wait.
Installer is forced disruptive

Verifying image bootflash:/nxos.9.3.4.bin for boot variable "nxos".
[] 100% -- SUCCESS

Verifying image type.
[] 100% -- SUCCESS

Preparing "nxos" version info using image bootflash:/nxos.9.3.4.bin.
[] 100% -- SUCCESS

Preparing "bios" version info using image bootflash:/nxos.9.3.4.bin.
[] 100% -- SUCCESS

Performing module support checks.
[] 100% -- SUCCESS

Notifying services about system upgrade.
[] 100% -- SUCCESS


Compatibility check is done:
Module  bootable          Impact              Install-type  Reason
------- ----------------- ------------------- ------------- ----------
     1     Yes            Disruptive          Reset         Default upgrade is not hitless


Images will be upgraded according to following table:
Module       Image       Running-Version(pri:alt)                New-Version          Upg-Required
------------ ----------- --------------------------------------- -------------------- ------------
     1       nxos        9.3(3)                                  9.3(4)               yes
     1       bios        v08.37(01/28/2020):v08.32(10/18/2016)   v08.37(01/28/2020)   no


Switch will be reloaded for disruptive upgrade.
Do you want to continue with the installation (y/n)?  [n] y

Install is in progress, please wait.

Performing runtime checks.
[] 100% -- SUCCESS

Setting boot variables.
[] 100% -- SUCCESS

Performing configuration copy.
[] 100% -- SUCCESS

Module 1: Refreshing compact flash and upgrading bios/loader/bootrom.
Warning: please do not remove or power off the module at this time.
[] 100% -- SUCCESS


Finishing the upgrade, switch will reboot in 10 seconds.
cs2#

  9. Überprüfen Sie nach dem Neustart des Switches die neue Version der NX-OS-Software:

    show version

    Beispiel anzeigen 
    cs2# show version
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (C) 2002-2020, Cisco and/or its affiliates.
All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under their own
licenses, such as open source.  This software is provided "as is," and unless
otherwise stated, there is no warranty, express or implied, including but not
limited to warranties of merchantability and fitness for a particular purpose.
Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or
GNU General Public License (GPL) version 3.0  or the GNU
Lesser General Public License (LGPL) Version 2.1 or
Lesser General Public License (LGPL) Version 2.0.
A copy of each such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://opensource.org/licenses/gpl-3.0.html and
http://www.opensource.org/licenses/lgpl-2.1.php and
http://www.gnu.org/licenses/old-licenses/library.txt.

Software
  BIOS: version 08.37
  NXOS: version 9.3(4)
  BIOS compile time:  01/28/2020
  NXOS image file is: bootflash:///nxos.9.3.4.bin
  NXOS compile time:  4/28/2020 21:00:00 [04/29/2020 06:28:31]

Hardware
 cisco Nexus3000 C3232C Chassis (Nexus 9000 Series)
  Intel(R) Xeon(R) CPU E5-2403 v2 @ 1.80GHz with 8154432 kB of memory.
  Processor Board ID FOCXXXXXXGS

  Device name: rtpnpi-mcc01-8200-ms-A1
  bootflash:   53298520 kB
Kernel uptime is 0 day(s), 0 hour(s), 3 minute(s), 14 second(s)

Last reset at 196755 usecs after Tue Nov 24 06:37:36 2020
  Reason: Reset due to upgrade
  System version: 9.3(3)
  Service:

plugin
  Core Plugin, Ethernet Plugin

Active Package(s):

cs2#

  10. Aktualisieren Sie das EPLD-Image und starten Sie den Switch neu.

    Beispiel anzeigen 
    cs2# show version module 1 epld

EPLD Device                     Version
---------------------------------------
MI   FPGA                       0x12
IO   FPGA                       0x11

cs2# install epld bootflash:n9000-epld.9.3.4.img module 1
Compatibility check:
Module        Type         Upgradable    Impact      Reason
------  -----------------  ----------    ----------  -----------------
     1         SUP         Yes           Disruptive  Module Upgradable

Retrieving EPLD versions.... Please wait.
Images will be upgraded according to following table:
Module  Type   EPLD              Running-Version   New-Version  Upg-Required
------  ----  -----------------  ---------------   -----------  ------------
     1   SUP   MI FPGA                0x12         0x12         No
     1   SUP   IO FPGA                0x11         0x12         Yes
The above modules require upgrade.
The switch will be reloaded at the end of the upgrade
Do you want to continue (y/n) ?  [n] y

Proceeding to upgrade Modules.

Starting Module 1 EPLD Upgrade

Module 1 : IO FPGA [Programming] : 100.00% (     64 of      64 sectors)
Module 1 EPLD upgrade is successful.
Module        Type  Upgrade-Result
------  ------------------  --------------
     1         SUP         Success

Module 1 EPLD upgrade is successful.
cs2#

  11. Wenn Sie auf NX-OS Version 9.3(11) aktualisieren, müssen Sie auch das EPLD aktualisieren. golden Image erstellen und den Switch erneut starten. Andernfalls fahren Sie mit Schritt 12 fort.

    Sehen "EPLD-Upgrade-Versionshinweise, Version 9.3(11)" für weitere Einzelheiten.

    Beispiel anzeigen 
    cs2# install epld bootflash:n9000-epld.9.3.11.img module 1 golden
Digital signature verification is successful
Compatibility check:
Module        Type         Upgradable     Impact      Reason
------  -----------------  -------------  ----------  -----------------
     1        SUP          Yes            Disruptive  Module Upgradable

Retrieving EPLD versions.... Please wait.
The above modules require upgrade.
The switch will be reloaded at the end of the upgrade
Do you want to continue (y/n) ?  [n] y

Proceeding to upgrade Modules.

 Starting Module 1 EPLD Upgrade

Module 1 : MI FPGA [Programming] : 100.00% (     64 of      64 sect)
Module 1 : IO FPGA [Programming] : 100.00% (     64 of      64 sect)
Module 1 EPLD upgrade is successful.
Module        Type          Upgrade-Result
------  ------------------  --------------
     1         SUP          Success

EPLDs upgraded.

Module 1 EPLD upgrade is successful.
cs2#

  12. Nach dem Neustart des Switches melden Sie sich an, um zu überprüfen, ob die neue Version von EPLD erfolgreich geladen wurde.

    Beispiel anzeigen 
    cs2# show version module 1 epld

EPLD Device                     Version
---------------------------------------
MI   FPGA                        0x12
IO   FPGA                        0x12

  13. Überprüfen Sie den Zustand der Cluster-Ports im Cluster.

    1. Überprüfen Sie, ob die Cluster-Ports auf allen Knoten im Cluster aktiv und fehlerfrei sind:

      network port show -role cluster

      Beispiel anzeigen 
      cluster1::*> network port show -role cluster

Node: cluster1-01
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e0a       Cluster      Cluster          up   9000  auto/10000 healthy  false
e0b       Cluster      Cluster          up   9000  auto/10000 healthy  false

Node: cluster1-02
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e0a       Cluster      Cluster          up   9000  auto/10000 healthy  false
e0b       Cluster      Cluster          up   9000  auto/10000 healthy  false

Node: cluster1-03
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e0a       Cluster      Cluster          up   9000  auto/100000 healthy false
e0d       Cluster      Cluster          up   9000  auto/100000 healthy false

Node: cluster1-04
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e0a       Cluster      Cluster          up   9000  auto/100000 healthy false
e0d       Cluster      Cluster          up   9000  auto/100000 healthy false
8 entries were displayed.

    2. Überprüfen Sie den Zustand der Switches im Cluster.

      network device-discovery show -protocol cdp

    Beispiel anzeigen 
    cluster1::*> network device-discovery show -protocol cdp
Node/       Local  Discovered
Protocol    Port   Device (LLDP: ChassisID)  Interface         Platform
----------- ------ ------------------------- ----------------- ----------
cluster1-01/cdp
            e0a    cs1                       Ethernet1/7       N3K-C3232C
            e0d    cs2                       Ethernet1/7       N3K-C3232C
cluster01-2/cdp
            e0a    cs1                       Ethernet1/8       N3K-C3232C
            e0d    cs2                       Ethernet1/8       N3K-C3232C
cluster01-3/cdp
            e0a    cs1                       Ethernet1/1/1     N3K-C3232C
            e0b    cs2                       Ethernet1/1/1     N3K-C3232C
cluster1-04/cdp
            e0a    cs1                       Ethernet1/1/2     N3K-C3232C
            e0b    cs2                       Ethernet1/1/2     N3K-C3232C

cluster1::*> system cluster-switch show -is-monitoring-enabled-operational true
Switch                      Type               Address          Model
--------------------------- ------------------ ---------------- ----------
cs1                         cluster-network    10.233.205.90    N3K-C3232C
     Serial Number: FOCXXXXXXGD
      Is Monitored: true
            Reason: None
  Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                    9.3(5)
    Version Source: CDP

cs2                         cluster-network    10.233.205.91    N3K-C3232C
     Serial Number: FOCXXXXXXGS
      Is Monitored: true
            Reason: None
  Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                    9.3(5)
    Version Source: CDP

2 entries were displayed.

    Je nach der zuvor auf dem Switch geladenen RCF-Version kann die folgende Ausgabe auf der cs1-Switch-Konsole angezeigt werden:

    2020 Nov 17 16:07:18 cs1 %$ VDC-1 %$ %STP-2-UNBLOCK_CONSIST_PORT: Unblocking port port-channel1 on VLAN0092. Port consistency restored.
2020 Nov 17 16:07:23 cs1 %$ VDC-1 %$ %STP-2-BLOCK_PVID_PEER: Blocking port-channel1 on VLAN0001. Inconsistent peer vlan.
2020 Nov 17 16:07:23 cs1 %$ VDC-1 %$ %STP-2-BLOCK_PVID_LOCAL: Blocking port-channel1 on VLAN0092. Inconsistent local vlan.

  14. Überprüfen Sie, ob der Cluster fehlerfrei funktioniert:

    cluster show

    Beispiel anzeigen 
    cluster1::*> cluster show
Node                 Health   Eligibility   Epsilon
-------------------- -------- ------------- -------
cluster1-01          true     true          false
cluster1-02          true     true          false
cluster1-03          true     true          true
cluster1-04          true     true          false
4 entries were displayed.
cluster1::*>

  15. Wiederholen Sie die Schritte 6 bis 14 auf Switch cs1.

  16. Automatische Wiederherstellung der Cluster-LIFs aktivieren.

    network interface modify -vserver Cluster -lif * -auto-revert true

  17. Überprüfen Sie, ob die Cluster-LIFs wieder auf ihren Heimatport zurückgekehrt sind:

    network interface show -role cluster

    Beispiel anzeigen 
    cluster1::*> network interface show -role cluster
            Logical            Status     Network            Current             Current Is
Vserver     Interface          Admin/Oper Address/Mask       Node                Port    Home
----------- ------------------ ---------- ------------------ ------------------- ------- ----
Cluster
            cluster1-01_clus1  up/up      169.254.3.4/23     cluster1-01         e0d     true
            cluster1-01_clus2  up/up      169.254.3.5/23     cluster1-01         e0d     true
            cluster1-02_clus1  up/up      169.254.3.8/23     cluster1-02         e0d     true
            cluster1-02_clus2  up/up      169.254.3.9/23     cluster1-02         e0d     true
            cluster1-03_clus1  up/up      169.254.1.3/23     cluster1-03         e0b     true
            cluster1-03_clus2  up/up      169.254.1.1/23     cluster1-03         e0b     true
            cluster1-04_clus1  up/up      169.254.1.6/23     cluster1-04         e0b     true
            cluster1-04_clus2  up/up      169.254.1.7/23     cluster1-04         e0b     true
8 entries were displayed.
cluster1::*>

    Falls Cluster-LIFs nicht zu ihren Heimatports zurückgekehrt sind, setzen Sie sie manuell vom lokalen Knoten aus zurück:

    network interface revert -vserver Cluster -lif <lif_name>

Wie geht es weiter?

Nach der Installation der NX-OS-Software können Sie "Installieren oder aktualisieren Sie die Referenzkonfigurationsdatei (RCF)."Die