Skip to main content
Se proporciona el idioma español mediante traducción automática para su comodidad. En caso de alguna inconsistencia, el inglés precede al español.

Instale o actualice el software NX-OS

Colaboradores netapp-yvonneo
PDF

Siga este procedimiento para instalar o actualizar el software NX-OS en el conmutador Nexus 9364D-GX2A.

Revise los requisitos

Antes de empezar

Verifique lo siguiente:

  • Complete el procedimiento en"Prepare la instalación de NX-OS y RCF" .

  • Está disponible una copia de seguridad actual de la configuración del conmutador.

  • Se ha instalado un clúster en pleno funcionamiento (sin errores en los registros ni problemas similares).

Documentación sugerida

  • "Página del switch Cisco Ethernet"

    Consulte en la tabla de compatibilidad del switch las versiones ONTAP y NX-OS compatibles.

  • "Guías de actualización y degradación de software"

    Consulte las guías de software y actualización correspondientes disponibles en el sitio web de Cisco para obtener documentación completa sobre los procedimientos de actualización y degradación del conmutador Cisco.

  • "Matriz de ISSU y actualización de Cisco Nexus 9000 y 3000"

    Proporciona información sobre actualización/degradación disruptiva para software Cisco NX-OS en los switches de la serie Nexus 9000 en función de tus versiones actuales y objetivo.

    En la página, selecciona Actualización disruptiva y selecciona tu versión actual y la versión de destino de la lista desplegable.

Acerca de los ejemplos

Los ejemplos de este procedimiento utilizan la nomenclatura de conmutador y nodo siguiente:

  • Los nombres de los dos switches de Cisco son cs1 y cs2.

  • Los nombres de los nodos son node1-01, node1-02, node1-03 y node1-04.

  • Los nombres del clúster LIF son node1-01_clus1, node1-01_clus2, node1-02_clus1, node1-02_clus2, node1-03_clus1, node1-03_clus2, node1-04_clus1 y node1-04_clus2.

  • La cluster1::*> prompt indica el nombre del clúster.

Instale el software

Para ello, es necesario utilizar tanto comandos de la ONTAP como comandos de la serie Cisco Nexus 9000; los comandos de la ONTAP se usan a menos que se indique lo contrario.

Importante

  • NX-OS 10.4.2 es la única versión compatible con los conmutadores Cisco Nexus 9364D-GX2A en un clúster ONTAP .

  • No actualice ni degrade su versión de NX-OS a una versión no compatible; actualmente solo se admite la versión 10.4.2.
Pasos

  1. Conecte el conmutador a la red de administración.

  2. Utilice el comando ping para verificar la conectividad con el servidor que aloja el software NX-OS y el RCF.

    Muestra el ejemplo

    Este ejemplo verifica que el switch puede llegar al servidor en la dirección IP 172.19.2.1:

    cs2# ping 172.19.2.1
Pinging 172.19.2.1 with 0 bytes of data:

Reply From 172.19.2.1: icmp_seq = 0. time= 5910 usec.

  3. Muestre los puertos del clúster en cada nodo que están conectados a los switches de clúster:

    network device-discovery show
    Muestra el ejemplo 
    cluster1::*> network device-discovery show

Node/       Local  Discovered
Protocol    Port   Device (LLDP: ChassisID) Interface         Platform
----------- ------ ------------------------ ----------------  ----------------
node1-01/cdp
            e10a   cs1(FLMXXXXXXXX)         Ethernet1/16/3    N9K-C9364D-GX2A
            e10b   cs2(FDOXXXXXXXX)         Ethernet1/13/3    N9K-C9364D-GX2A
            e11a   cs1(FLMXXXXXXXX)         Ethernet1/16/4    N9K-C9364D-GX2A
            e11b   cs2(FDOXXXXXXXX)         Ethernet1/13/4    N9K-C9364D-GX2A
            e1a    cs1(FLMXXXXXXXX)         Ethernet1/16/1    N9K-C9364D-GX2A
            e1b    cs2(FDOXXXXXXXX)         Ethernet1/13/1    N9K-C9364D-GX2A
            .
            .
            .

            e7a    cs1(FLMXXXXXXXX)         Ethernet1/16/2    N9K-C9364D-GX2A
            e7b    cs2(FDOXXXXXXXX)         Ethernet1/13/2    N9K-C9364D-GX2A

node1-01/lldp
            e10a   cs1 (c8:60:8f:xx:xx:xx)  Ethernet1/16/3    -
            e10b   cs2 (04:e3:87:xx:xx:xx)  Ethernet1/13/3    -
            e11a   cs1 (c8:60:8f:xx:xx:xx)  Ethernet1/16/4    -
            e11b   cs2 (04:e3:87:xx:xx:xx)  Ethernet1/13/4    -
            e1a    cs1 (c8:60:8f:xx:xx:xx)  Ethernet1/16/1    -
            e1b    cs2 (04:e3:87:xx:xx:xx)  Ethernet1/13/1    -
            .
            .
            .
            e7a    cs1 (c8:60:8f:xx:xx:xx)  Ethernet1/16/2    -
            e7b    cs2 (04:e3:87:xx:xx:xx)  Ethernet1/13/2    -
.
.
.

  4. Consulta el estado administrativo y operativo de cada puerto.

    1. Puertos de clúster

      1. Compruebe que todos los puertos del clúster tengan el estado correcto:

        network port show -ipspace Cluster
        Muestra el ejemplo 
        cluster1::*> network port show -ipspace Cluster

Node: node1-01
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/100000 healthy false
e7b       Cluster      Cluster          up   9000  auto/100000 healthy false

Node: node1-02
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/100000 healthy false
e7b       Cluster      Cluster          up   9000  auto/100000 healthy false

Node: node1-03

                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/10000 healthy  false
e7b       Cluster      Cluster          up   9000  auto/10000 healthy  false

Node: node1-04
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/10000 healthy  false
e7b       Cluster      Cluster          up   9000  auto/10000 healthy  false

      2. Compruebe que todas las interfaces del clúster (LIF) están en el puerto de inicio:

        network interface show -role cluster
        Muestra el ejemplo 
        cluster1::*> network interface show -role cluster

            Logical         Status     Network            Current   Current Is
Vserver     Interface       Admin/Oper Address/Mask       Node      Port    Home
----------- --------------- ---------- ------------------ --------- ------- ----
Cluster
            node1-01_clus1  up/up      169.254.36.44/16   node1-01  e7a     true
            node1-01_clus2  up/up      169.254.7.5/16     node1-01  e7b     true
            node1-02_clus1  up/up      169.254.197.206/16 node1-02  e7a     true
            node1-02_clus2  up/up      169.254.195.186/16 node1-02  e7b     true
            node1-03_clus1  up/up      169.254.192.49/16  node1-03  e7a     true
            node1-03_clus2  up/up      169.254.182.76/16  node1-03  e7b     true
            node1-04_clus1  up/up      169.254.59.49/16   node1-04  e7a     true
            node1-04_clus2  up/up      169.254.62.244/16  node1-04  e7b     true

8 entries were displayed.

      3. Compruebe que el clúster muestra información de ambos switches de clúster:

        system cluster-switch show -is-monitoring-enabled-operational true
        Muestra el ejemplo 
        cluster1::*> system cluster-switch show -is-monitoring-enabled-operational true

Switch                      Type               Address          Model
--------------------------- ------------------ ---------------- ---------------
cs2(FDOXXXXXXXX)            cluster-network    10.228.137.233   N9K-C9364D-GX2A
     Serial Number: FDOXXXXXXXX
      Is Monitored: true
            Reason: None
  Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                    10.4(2)
    Version Source: CDP/ISDP


cs1(FLMXXXXXXXX)             cluster-network   10.228.137.253   N9K-C9364D-GX2A
     Serial Number: FLMXXXXXXXX
      Is Monitored: true
            Reason: None
  Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                    10.4(2)
    Version Source: CDP/ISDP

2 entries were displayed.

    2. Puertos HA

      1. Verifique que todos los puertos HA estén activos con un estado saludable:

        ha interconnect status show -node <node-name>

    Muestra el ejemplo 
    cluster1::*> ha interconnect status show -node node1-01
  (system ha interconnect status show)

                       Node: node1-01
              Link 0 Status: up
              Link 1 Status: up
           Is Link 0 Active: true
           Is Link 1 Active: true
         IC RDMA Connection: up
                       Slot: 0
             Debug Firmware: no


Interconnect Port 0 :
                  Port Name: e1a-17
                        MTU: 4096
           Link Information: ACTIVE


Interconnect Port 1 :
                  Port Name: e1b-18
                        MTU: 4096
           Link Information: ACTIVE

cluster1::*> ha interconnect status show -node node1-02
  (system ha interconnect status show)

                       Node: node1-02
              Link 0 Status: up
              Link 1 Status: up
           Is Link 0 Active: true
           Is Link 1 Active: true
         IC RDMA Connection: up
                       Slot: 0
             Debug Firmware: no


Interconnect Port 0 :
                  Port Name: e1a-17
                        MTU: 4096
           Link Information: ACTIVE


Interconnect Port 1 :
                  Port Name: e1b-18
                        MTU: 4096
           Link Information: ACTIVE
.
.
.

    1. Puertos de almacenamiento

      1. Verifique que todos los puertos de almacenamiento se encuentren en buen estado:

        storage port show -port-type ENET
        Muestra el ejemplo 
        cluster1::*> storage port show -port-type ENET

                                      Speed
Node               Port Type  Mode    (Gb/s) State    Status
------------------ ---- ----- ------- ------ -------- -----------
node1-01
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
                   e11b ENET  -          100 enabled  online
node1-02
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
                   e11b ENET  -          100 enabled  online
node1-03
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
node1-04
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
                   e11b ENET  -          100 enabled  online
16 entries were displayed.

    2. Puertos para estantes de almacenamiento

      1. Verifique que todos los puertos del estante de almacenamiento estén activos con un estado saludable:

        storage shelf port show
        Muestra el ejemplo 
        cluster1::*> storage shelf port show

Shelf ID Module State        Internal?
----- -- ------ ------------ ---------
1.1
       0 A      connected    false
       1 A      connected    false
       2 A      connected    false
       3 A      connected    false
       4 A      connected    false
       5 A      connected    false
       6 A      connected    false
       7 A      connected    false
       8 B      connected    false
       9 B      connected    false
      10 B      connected    false
      11 B      connected    false
      12 B      connected    false
      13 B      connected    false
      14 B      connected    false
      15 B      connected    false

16 entries were displayed.

      2. Verifique el estado de conexión de todos los puertos del estante de almacenamiento:

        storage shelf port show -fields remote-device,remote-port,connector-state
        Muestra el ejemplo 
        cluster1::*> storage shelf port show -fields remote-device,remote-port,connector-state

shelf id connector-state remote-port    remote-device
----- -- --------------- -------------- -----------------
1.1   0  connected       Ethernet1/17/1 CX9332D-cs1
1.1   1  connected       Ethernet1/15/1 CX9364D-cs1
1.1   2  connected       Ethernet1/17/2 CX9332D-cs1
1.1   3  connected       Ethernet1/15/2 CX9364D-cs1
1.1   4  connected       Ethernet1/17/3 CX9332D-cs1
1.1   5  connected       Ethernet1/15/3 CX9364D-cs1
1.1   6  connected       Ethernet1/17/4 CX9332D-cs1
1.1   7  connected       Ethernet1/15/4 CX9364D-cs1
1.1   8  connected       Ethernet1/19/1 CX9332D-cs1
1.1   9  connected       Ethernet1/17/1 CX9364D-cs1
1.1   10 connected       Ethernet1/19/2 CX9332D-cs1
1.1   11 connected       Ethernet1/17/2 CX9364D-cs1
1.1   12 connected       Ethernet1/19/3 CX9332D-cs1
1.1   13 connected       Ethernet1/17/3 CX9364D-cs1
1.1   14 connected       Ethernet1/19/4 CX9332D-cs1
1.1   15 connected       Ethernet1/17/4 CX9364D-cs1

16 entries were displayed.

  5. Deshabilite la reversión automática en las LIF del clúster. Los LIF de clúster conmutan al switch del clúster asociado y permanecen allí mientras realiza el procedimiento de actualización en el switch de destino:

    network interface modify -vserver Cluster -lif * -auto-revert false

  6. Copie el software NX-OS y las imágenes EPLD al conmutador Nexus 9364D-GX2A.

    Muestra el ejemplo 
    cs2# copy sftp: bootflash: vrf management
Enter source filename: /code/nxos.10.4.2.bin
Enter hostname for the sftp server: 172.19.2.1
Enter username: root

Outbound-ReKey for 172.19.2.1:22
Inbound-ReKey for 172.19.2.1:22
root@172.19.2.1's password:
sftp> progress
Progress meter enabled
sftp> get   /code/nxos.10.4.2.bin  /bootflash/nxos.10.4.2.bin
/code/nxos.10.4.2.bin  100% 1261MB   9.3MB/s   02:15
sftp> exit
Copy complete, now saving to disk (please wait)...
Copy complete.

cs2# copy sftp: bootflash: vrf management
Enter source filename: /code/n9000-epld.10.4.2.F.img
Enter hostname for the sftp server: 172.19.2.1
Enter username: user1

Outbound-ReKey for 172.19.2.1:22
Inbound-ReKey for 172.19.2.1:22
user1@172.19.2.1's password:
sftp> progress
Progress meter enabled
sftp> get   /code/n9000-epld.10.4.2.F.img  /bootflash/n9000-epld.10.4.2.F.img
/code/n9000-epld.10.4.2.F.img  100%  161MB   9.5MB/s   00:16
sftp> exit
Copy complete, now saving to disk (please wait)...
Copy complete.

  7. Compruebe la versión que se está ejecutando del software NX-OS:

    show version

    Muestra el ejemplo 
    cs2# show version
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (C) 2002-2025, Cisco and/or its affiliates.
All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under their own
licenses, such as open source.  This software is provided "as is," and unless
otherwise stated, there is no warranty, express or implied, including but not
limited to warranties of merchantability and fitness for a particular purpose.
Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or
GNU General Public License (GPL) version 3.0  or the GNU
Lesser General Public License (LGPL) Version 2.1 or
Lesser General Public License (LGPL) Version 2.0.
A copy of each such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://opensource.org/licenses/gpl-3.0.html and
http://www.opensource.org/licenses/lgpl-2.1.php and
http://www.gnu.org/licenses/old-licenses/library.txt.


Software
  BIOS: version 01.14
  NXOS: version 10.4(1) [Feature Release]
  Host NXOS: version 10.4(1)
  BIOS compile time:  11/25/2024
  NXOS image file is: bootflash:///nxos64-cs.10.4.1.F.bin
  NXOS compile time:  11/30/2023 12:00:00 [12/14/2023 05:25:50]
  NXOS boot mode: LXC


Hardware
  cisco Nexus9000 C9332D-GX2B Chassis
  Intel(R) Xeon(R) CPU D-1633N @ 2.50GHz with 32802156 kB of memory.
  Processor Board ID FLMXXXXXXXX
  Device name: cs2
  bootflash:  115802886 kB


Kernel uptime is 5 day(s), 2 hour(s), 13 minute(s), 21 second(s)


Last reset at 3580 usecs after Thu Jun  5 15:55:08 2025
  Reason: Reset Requested by CLI command reload
  System version: 10.4(1)
  Service:


plugin
  Core Plugin, Ethernet Plugin


Active Package(s):

cs2#

  8. Instale la imagen NX-OS.

    La instalación del archivo de imagen hace que se cargue cada vez que se reinicia el conmutador.

    Muestra el ejemplo 
    cs2# install all nxos bootflash:nxos.10.4.2.bin

Installer will perform compatibility check first. Please wait.
Installer is forced disruptive

Verifying image bootflash:/nxos.10.4.2.bin for boot variable "nxos".
[] 100% -- SUCCESS

Verifying image type.
[] 100% -- SUCCESS

Preparing "nxos" version info using image bootflash:/nxos.10.4.2.bin.
[] 100% -- SUCCESS

Preparing "bios" version info using image bootflash:/nxos.10.4.2.bin.
[] 100% -- SUCCESS

Performing module support checks.
[] 100% -- SUCCESS

Notifying services about system upgrade.
[] 100% -- SUCCESS


Compatibility check is done:
Module  Bootable  Impact          Install-type  Reason
------  --------  --------------- ------------  ---------
  1     yes       Disruptive      Reset         Default upgrade is not hitless



Images will be upgraded according to following table:

Module   Image    Running-Version(pri:alt)                 New-Version         Upg-Required
------- --------- ---------------------------------------- ------------------- ------------
  1      nxos     10.4(1)                                  10.4(2)             Yes
  1      bios     xx.xx.:xx.xx                             xxx                 No


Switch will be reloaded for disruptive upgrade.

Do you want to continue with the installation (y/n)? [n] y

Install is in progress, please wait.

Performing runtime checks.
[] 100% -- SUCCESS

Setting boot variables.
[] 100% -- SUCCESS

Performing configuration copy.
[] 100% -- SUCCESS

Module 1: Refreshing compact flash and upgrading bios/loader/bootrom.
Warning: please do not remove or power off the module at this time.
[] 100% -- SUCCESS

Finishing the upgrade, switch will reboot in 10 seconds.

  9. Compruebe la nueva versión del software NX-OS una vez que se haya reiniciado el switch:

    show version

    Muestra el ejemplo 
    cs2# show version
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (C) 2002-2025, Cisco and/or its affiliates.
All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under their own
licenses, such as open source.  This software is provided "as is," and unless
otherwise stated, there is no warranty, express or implied, including but not
limited to warranties of merchantability and fitness for a particular purpose.
Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or
GNU General Public License (GPL) version 3.0  or the GNU
Lesser General Public License (LGPL) Version 2.1 or
Lesser General Public License (LGPL) Version 2.0.
A copy of each such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://opensource.org/licenses/gpl-3.0.html and
http://www.opensource.org/licenses/lgpl-2.1.php and
http://www.gnu.org/licenses/old-licenses/library.txt.


Software
  BIOS: version 01.14
  NXOS: version 10.4(2) [Feature Release]
  Host NXOS: version 10.4(2)
  BIOS compile time:  11/25/2024
  NXOS image file is: bootflash:///nxos64-cs.10.4.2.F.bin
  NXOS compile time:  11/30/2023 12:00:00 [12/14/2023 05:25:50]
  NXOS boot mode: LXC


Hardware
  cisco Nexus9000 C9332D-GX2B Chassis
  Intel(R) Xeon(R) CPU D-1633N @ 2.50GHz with 32802156 kB of memory.
  Processor Board ID FLMXXXXXXXX
  Device name: cs2
  bootflash:  115802886 kB


Kernel uptime is 5 day(s), 2 hour(s), 13 minute(s), 21 second(s)


Last reset at 3580 usecs after Thu Jun  5 15:55:08 2025
  Reason: Reset Requested by CLI command reload
  System version: 10.4(2)
  Service:


plugin
  Core Plugin, Ethernet Plugin


Active Package(s):

cs2#

  10. Actualice la imagen de EPLD y reinicie el switch.

    Muestra el ejemplo 
    cs2# show version module 1 epld

EPLD Device                     Version
---------------------------------------
MI   FPGA                        0x7
IO   FPGA                        0x17
MI   FPGA2                       0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2

cs2# install epld bootflash:n9000-epld.10.4.2.F.img module all
Compatibility check:
Module        Type         Upgradable        Impact    Reason
------  ------------------ ----------------- --------- -----------
     1         SUP         Yes       disruptive  Module Upgradable

Retrieving EPLD versions.... Please wait.
Images will be upgraded according to following table:
Module  Type   EPLD              Running-Version   New-Version  Upg-Required
------- ------ ----------------- ----------------- ------------ ------------
     1  SUP    MI FPGA           0x07              0x07         No
     1  SUP    IO FPGA           0x17              0x19         Yes
     1  SUP    MI FPGA2          0x02              0x02         No
The above modules require upgrade.
The switch will be reloaded at the end of the upgrade
Do you want to continue (y/n) ?  [n] y

Proceeding to upgrade Modules.

Starting Module 1 EPLD Upgrade

Module 1 : IO FPGA [Programming] : 100.00% (     64 of      64 sectors)
Module 1 EPLD upgrade is successful.
Module   Type  Upgrade-Result
-------- ----- --------------
     1   SUP   Success

EPLDs upgraded.

Module 1 EPLD upgrade is successful.

  11. Tras reiniciar el conmutador, vuelva a iniciar sesión y compruebe que la nueva versión de EPLD se ha cargado correctamente.

    Muestra el ejemplo 
    cs2# show version module 1 epld

EPLD Device                     Version
---------------------------------------
MI   FPGA                        0x7
IO   FPGA                        0x19
MI   FPGA2                       0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2

  12. Verificar el estado de todos los puertos del clúster.

    1. Puertos de clúster

      1. Compruebe que los puertos del clúster estén en buen estado en todos los nodos del clúster:

        network port show -ipspace Cluster
        Muestra el ejemplo 
        cluster1::*> network port show -ipspace Cluster

Node: node1-01
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/10000 healthy  false
e7b       Cluster      Cluster          up   9000  auto/10000 healthy  false

Node: node1-02
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/10000 healthy  false
e7b       Cluster      Cluster          up   9000  auto/10000 healthy  false

Node: node1-03
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/100000 healthy false
e7b       Cluster      Cluster          up   9000  auto/100000 healthy false

Node: node1-04
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e7a       Cluster      Cluster          up   9000  auto/100000 healthy false
e7b       Cluster      Cluster          up   9000  auto/100000 healthy false

      2. Compruebe el estado del switch del clúster:

        network device-discovery show -protocol cdp
        system cluster-switch show -is-monitoring-enabled-operational true
        Muestra el ejemplo 
        cluster1::*> network device-discovery show -protocol cdp

node1-01/cdp
            e10a   cs1(FLMXXXXXXXX)         Ethernet1/16/3    N9K-C9364D-GX2A
            e10b   cs2(FDOXXXXXXXX)         Ethernet1/13/3    N9K-C9364D-GX2A
            e11a   cs1(FLMXXXXXXXX)         Ethernet1/16/4    N9K-C9364D-GX2A
            e11b   cs2(FDOXXXXXXXX)         Ethernet1/13/4    N9K-C9364D-GX2A
            e1a    cs1(FLMXXXXXXXX)         Ethernet1/16/1    N9K-C9364D-GX2A
            e1b    cs2(FDOXXXXXXXX)         Ethernet1/13/1    N9K-C9364D-GX2A
            .
            .
            .
            e7a    cs1(FLMXXXXXXXX)         Ethernet1/16/2    N9K-C9364D-GX2A
            e7b    cs2(FDOXXXXXXXX)         Ethernet1/13/2    N9K-C9364D-GX2A

node1-02/cdp
            e10a   cs1(FLMXXXXXXXX)         Ethernet1/16/3    N9K-C9364D-GX2A
            e10b   cs2(FDOXXXXXXXX)         Ethernet1/13/3    N9K-C9364D-GX2A
            e11a   cs1(FLMXXXXXXXX)         Ethernet1/16/4    N9K-C9364D-GX2A
            e11b   cs2(FDOXXXXXXXX)         Ethernet1/13/4    N9K-C9364D-GX2A
            e1a    cs1(FLMXXXXXXXX)         Ethernet1/16/1    N9K-C9364D-GX2A
            e1b    cs2(FDOXXXXXXXX)         Ethernet1/13/1    N9K-C9364D-GX2A
            .
            .
            .
            e7a    cs1(FLMXXXXXXXX)         Ethernet1/16/2    N9K-C9364D-GX2A
            e7b    cs2(FDOXXXXXXXX)         Ethernet1/13/2    N9K-C9364D-GX2A
.
.
.

cluster1::*> system cluster-switch show -is-monitoring-enabled-operational true
Switch                      Type               Address          Model
--------------------------- ------------------ ---------------- ---------------
cs2(FDOXXXXXXXX)            cluster-network    10.228.137.233   N9K-C9364D-GX2A
     Serial Number: FDOXXXXXXXX
      Is Monitored: true
            Reason: None
  Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                    10.4(2)
    Version Source: CDP/ISDP


cs1(FLMXXXXXXXX)             cluster-network   10.228.137.253   N9K-C9364D-GX2A
     Serial Number: FLMXXXXXXXX
      Is Monitored: true
            Reason: None
  Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                    10.4(2)
    Version Source: CDP/ISDP

    2. Puertos HA

      1. Verifique que todos los puertos HA estén activos con un estado saludable:

        ha interconnect status show -node <node-name>

    Muestra el ejemplo 
    cluster1::*> ha interconnect status show -node node1-01
  (system ha interconnect status show)

                       Node: node1-01
              Link 0 Status: up
              Link 1 Status: up
           Is Link 0 Active: true
           Is Link 1 Active: true
         IC RDMA Connection: up
                       Slot: 0
             Debug Firmware: no


Interconnect Port 0 :
                  Port Name: e1a-17
                        MTU: 4096
           Link Information: ACTIVE


Interconnect Port 1 :
                  Port Name: e1b-18
                        MTU: 4096
           Link Information: ACTIVE

cluster1::*> ha interconnect status show -node node1-02
  (system ha interconnect status show)

                       Node: node1-02
              Link 0 Status: up
              Link 1 Status: up
           Is Link 0 Active: true
           Is Link 1 Active: true
         IC RDMA Connection: up
                       Slot: 0
             Debug Firmware: no


Interconnect Port 0 :
                  Port Name: e1a-17
                        MTU: 4096
           Link Information: ACTIVE


Interconnect Port 1 :
                  Port Name: e1b-18
                        MTU: 4096
           Link Information: ACTIVE
.
.
.

    1. Puertos de almacenamiento

      1. Verifique que todos los puertos de almacenamiento se encuentren en buen estado:

        storage port show -port-type ENET
        Muestra el ejemplo 
        cluster1::*> storage port show -port-type ENET

                                      Speed
Node               Port Type  Mode    (Gb/s) State    Status
------------------ ---- ----- ------- ------ -------- -----------
node1-01
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
                   e11b ENET  -          100 enabled  online
node1-02
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
                   e11b ENET  -          100 enabled  online
node1-03
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
node1-04
                   e10a ENET  -          100 enabled  online
                   e10b ENET  -          100 enabled  online
                   e11a ENET  -          100 enabled  online
                   e11b ENET  -          100 enabled  online
16 entries were displayed.

    2. Puertos para estantes de almacenamiento

      1. Verifique que todos los puertos del estante de almacenamiento estén activos con un estado saludable:

        storage shelf port show
        Muestra el ejemplo 
        cluster1::*> storage shelf port show

Shelf ID Module State        Internal?
----- -- ------ ------------ ---------
1.1
       0 A      connected    false
       1 A      connected    false
       2 A      connected    false
       3 A      connected    false
       4 A      connected    false
       5 A      connected    false
       6 A      connected    false
       7 A      connected    false
       8 B      connected    false
       9 B      connected    false
      10 B      connected    false
      11 B      connected    false
      12 B      connected    false
      13 B      connected    false
      14 B      connected    false
      15 B      connected    false

16 entries were displayed.

      2. Verifique el estado de conexión de todos los puertos del estante de almacenamiento:

        storage shelf port show -fields remote-device,remote-port,connector-state
        Muestra el ejemplo 
        cluster1::*> storage shelf port show -fields remote-device,remote-port,connector-state

shelf id connector-state remote-port    remote-device
----- -- --------------- -------------- -----------------
1.1   0  connected       Ethernet1/17/1 CX9332D-cs1
1.1   1  connected       Ethernet1/15/1 CX9364D-cs1
1.1   2  connected       Ethernet1/17/2 CX9332D-cs1
1.1   3  connected       Ethernet1/15/2 CX9364D-cs1
1.1   4  connected       Ethernet1/17/3 CX9332D-cs1
1.1   5  connected       Ethernet1/15/3 CX9364D-cs1
1.1   6  connected       Ethernet1/17/4 CX9332D-cs1
1.1   7  connected       Ethernet1/15/4 CX9364D-cs1
1.1   8  connected       Ethernet1/19/1 CX9332D-cs1
1.1   9  connected       Ethernet1/17/1 CX9364D-cs1
1.1   10 connected       Ethernet1/19/2 CX9332D-cs1
1.1   11 connected       Ethernet1/17/2 CX9364D-cs1
1.1   12 connected       Ethernet1/19/3 CX9332D-cs1
1.1   13 connected       Ethernet1/17/3 CX9364D-cs1
1.1   14 connected       Ethernet1/19/4 CX9332D-cs1
1.1   15 connected       Ethernet1/17/4 CX9364D-cs1

16 entries were displayed.

  13. Compruebe que el clúster esté en buen estado:

    cluster show

    Muestra el ejemplo 
    cluster1::*> cluster show


Node                 Health  Eligibility   Epsilon
-------------------- ------- ------------  ------------
node1-01             true    true          false
node1-02             true    true          false
node1-03             true    true          false
node1-04             true    true          true

4 entries were displayed.

  14. Repita los pasos 6 a 13 para instalar el software NX-OS en el interruptor CS1.

  15. Habilite la reversión automática en las LIF del clúster.

    network interface modify -vserver Cluster -lif * -auto-revert true

  16. Compruebe que las LIF del clúster han vuelto a su puerto de inicio:

    network interface show -role cluster
    Muestra el ejemplo 
    cluster1::*> network interface show -role cluster

            Logical         Status     Network            Current     Current Is
Vserver     Interface       Admin/Oper Address/Mask       Node        Port    Home
----------- --------------- ---------- ------------------ ----------- ------- ----
Cluster
            node1-01_clus1  up/up      169.254.36.44/16   node1-01    e7a     true
            node1-01_clus2  up/up      169.254.7.5/16     node1-01    e7b     true
            node1-02_clus1  up/up      169.254.197.206/16 node1-02    e7a     true
            node1-02_clus2  up/up      169.254.195.186/16 node1-02    e7b     true
            node1-03_clus1  up/up      169.254.192.49/16  node1-03    e7a     true
            node1-03_clus2  up/up      169.254.182.76/16  node1-03    e7b     true
            node1-04_clus1  up/up      169.254.59.49/16   node1-04    e7a     true
            node1-04_clus2  up/up      169.254.62.244/16  node1-04    e7b     true

    Si alguna LIF de clúster no ha regresado a sus puertos raíz, revertirla manualmente desde el nodo local:

    network interface revert -vserver Cluster -lif <lif-name>

El futuro

Después de haber instalado o actualizado el software NX-OS,"instalar o actualizar el archivo de configuración de referencia (RCF)" .