# sanlun lun show all

controller(7mode/E-Series)/            device     host               lun
vserver(cDOT/FlashRay)   lun-pathname  filename   adapter  protocol  size    Product
------------------------------------------------------------------------------------
data_vserver          /vol/vol1/lun1   /dev/sdb   host16   FCP       120.0g  cDOT
data_vserver          /vol/vol1/lun1   /dev/sdc   host15   FCP       120.0g  cDOT
data_vserver          /vol/vol2/lun2   /dev/sdd   host16   FCP       120.0g  cDOT
data_vserver          /vol/vol2/lun2   /dev/sde   host15   FCP       120.0g  cDOT

chkconfig multipathd on
/etc/init.d/multipathd start

blacklist {
        wwid <DevId>
        devnode "^(ram|raw|loop|fd|md|dm-|sr|scd|st)[0-9]*"
        devnode "^hd[a-z]"
        devnode "^cciss.*"
}

+
`sda` is the local SCSI disk that you want to add to the blacklist.

. Add the `WWID` to the blacklist stanza in `/etc/multipath.conf`:
[source,cli]
+

Always check your `/etc/multipath.conf` file, especially in the defaults section, for legacy settings that might be overriding default settings.

The following table demonstrates the critical `multipathd` parameters for ONTAP LUNs and the required values. If a host is connected to LUNs from other vendors and any of these parameters are overridden, they must be corrected by later stanzas in the `multipath.conf` file that apply specifically to ONTAP LUNs. Without this correction, the ONTAP LUNs might not work as expected. You should only override these defaults in consultation with NetApp, the OS vendor, or both, and only when the impact is fully understood.

//ONTAPDOC-2578 9-Dec-2024
//ONTAPDOC-2561 25-Nov-202

[cols=2*,options="header"]
|===
| Parameter
| Setting
| detect_prio | yes
| dev_loss_tmo | "infinity"
| failback | immediate
| fast_io_fail_tmo | 5
| features | "3 queue_if_no_path pg_init_retries 50"
| flush_on_last_del | "yes"
| hardware_handler | "0"
| no_path_retry | queue
| path_checker | "tur"
| path_grouping_policy | "group_by_prio"
| path_selector | "service-time 0"
| polling_interval | 5
| prio | "ontap"
| product | LUN.*
| retain_attached_hw_handler | yes
| rr_weight | "uniform"
| user_friendly_names | no
| vendor | NETAPP
|===

.Example

The following example shows how to correct an overridden default. In this case, the `multipath.conf` file defines values for `path_checker` and `no_path_retry` that are not compatible with ONTAP LUNs. If they cannot be removed because of other SAN arrays still attached to the host, these parameters can be corrected specifically for ONTAP LUNs with a device stanza.

=== Configure KVM settings

You can use the recommended settings to configure Kernel-based Virtual Machine (KVM) as well. There are no changes required to configure KVM because the LUN is mapped to the hypervisor.

//ONTAPDOC-2561 5-Dec-2024

== Known issues

The RHEL 7.6 with ONTAP release has the following known issues:

[cols=3*,options="header"]
|===
| NetApp Bug ID
| Title
| Description
| 1440718 | If you unmap or map a LUN without performing a SCSI rescan, it might lead to data corruption on the host. | When you set the 'disable_changed_wwids' multipath configuration parameter to YES, it disables access to the path device in the event of a WWID change. Multipath will disable access to the path device until the WWID of the path is restored to the WWID of the multipath device. To learn more, see  link:https://kb.netapp.com/Advice_and_Troubleshooting/Flash_Storage/AFF_Series/The_filesystem_corruption_on_iSCSI_LUN_on_the_Oracle_Linux_7[NetApp Knowledge Base: The filesystem corruption on iSCSI LUN on the Oracle Linux 7^].
| link:https://mysupport.netapp.com/NOW/cgi-bin/bol?Type=Detail&Display=1186754[1186754^] | Remote ports status on RHEL7U6 with QLogic QLE2742 host might be in blocked during host discovery | During host discovery, FC remote port status on RHEL7U6 host with a QLogic QLE2742 adapter might enter a blocked state. These blocked remote ports might result in the paths to LUNs becoming unavailable. During storage failover, the path redundancy might be reduced and result in I/O outage. You can check the remote port status by entering the following command:# cat /sys/class/fc_remote_ports/rport-*/port_state
| link:https://mysupport.netapp.com/NOW/cgi-bin/bol?Type=Detail&Display=1190698[1190698^] | Remote port status on RHEL7U6 with QLogic QLE2672 host might be in blocked during storage failover operations | FC remote ports might be blocked on Red Hat Enterprise Linux (RHEL) 7U6 with the QLogic QLE2672 host during storage failover operations. Because the logical interfaces go down when a storage node is down, the remote ports set the storage node status to blocked. When the storage node returns to its optimal state, the logical interfaces also come up and the remote ports should be online. However, the remote portsmight still be blocked. This blocked state registers as failed faulty to LUNS at the multipath layer. You can verify the remote ports state with the following command:# cat /sys/class/fc_remote_ports/rport-*/port_state
|===

// 2024 SEP 2, ONTAPDOC-2345