Configure IPMI for each node
Suggest changes
PDFs
After you have racked, cabled, and powered on your NetApp HCI hardware, you can configure Intelligent Platform Management Interface (IPMI) access for each node. Assign each IPMI port an IP address and change the default IPMI administrator password as soon as you have remote IPMI access to the node.
Prerequisites
After you have validated that your environment is ready to support NetApp HCI and resolved any potential issues, you need to complete some final tasks before deployment.
-
Ensure you have a successful report from Active IQ Config Advisor.
-
Gather all relevant information about your network, current or planned VMware infrastructure, and planned user credentials.
-
Rack, cable, and power on the NetApp HCI installation.
Manually assign the IPMI port IP address
Dynamic Host Configuration Protocol (DHCP) is enabled by default for the IPMI port of each NetApp HCI node. If your IPMI network does not use DHCP, you can manually assign a static IPv4 address to the IPMI port.
Ensure that you have a keyboard, video, and mouse (KVM) switch or monitor and keyboard you can use to access the BIOS of each node.
Use the arrow keys to navigate in the BIOS. Select a tab or option by pressing Enter. Go back to previous screens by pressing ESC.
-
Power on the node.
-
Upon booting, enter the BIOS by pressing the
Delkey. -
Select the IPMI tab.
-
Select BMC Network Configuration and press
Enter. -
Choose Yes and press
Enter. -
Select Configuration Address Source and press
Enter. -
Choose Static and press
Enter. -
Select Station IP address and enter a new IP address for the IPMI port. Press
Enterwhen finished. -
Select Subnet mask and enter a new subnet mask for the IPMI port. Press
Enterwhen finished. -
Select Gateway IP address and enter a new gateway IP address for the IPMI port. Press
Enterwhen finished. -
Connect one end of an Ethernet cable to the IPMI port and the other end to a switch.
The IPMI port for this node is ready to use.
-
Repeat this procedure for any other NetApp HCI nodes with IPMI ports that are not configured.
Change the default IPMI password for H410C and H410S nodes
You should change the default password for the IPMI administrator account on each compute and storage node as soon as you configure the IPMI network port.
You have configured the IPMI IP address for each compute and storage node.
-
Open a web browser on a computer that can reach the IPMI network and browse to the IPMI IP address for the node.
-
Enter the user name
ADMINand passwordADMINin the login prompt. -
Upon logging in, select the Configuration tab.
-
Select Users.
-
Select the
ADMINuser and select Modify User. -
Select the Change Password check box.
-
Enter a new password in the Password and Confirm Password fields.
-
Select Modify, and then select OK.
-
Repeat this procedure for any other NetApp HCI H410C and H410S nodes with default IPMI passwords.
Change the default IPMI password for H610C, H615C, and H610S nodes
You should change the default password for the IPMI administrator account on each compute and storage node as soon as you configure the IPMI network port.
You have configured the IPMI IP address for each compute and storage node.
-
Open a web browser on a computer that can reach the IPMI network and browse to the IPMI IP address for the node.
-
Enter the user name
rootand passwordcalvinin the login prompt. -
Upon logging in, select the menu navigation icon at the top left of the page to open the sidebar drawer.
-
Select Settings.
-
Select User Management.
-
Select the Administrator user from the list.
-
Enable the Change Password check box.
-
Enter a new, strong password in the Password and Confirm Password fields.
-
Select Save at the bottom of the page.
-
Repeat this procedure for any other NetApp HCI H610C, H615C, or H610S nodes with default IPMI passwords.