EMERGENCY

This message occurs when the NVRAM battery capacity is critically low. To prevent data loss, the system will shut down.

Correct any environmental problems, such as chassis over- temperature. The battery charges automatically. If the capacity is not restored automatically within 30 minutes after system power is on, replace the NVRAM battery. If the problem persists, replace the FRU (field-replaceable unit) NVRAM card or PCM, where the battery is located.

The NVRAM battery capacity is critically low (%s). To prevent data loss, the system will shut down in %d minutes.

reading (STRING): Reading that triggered this message.
num_minutes (INT): Number of minutes until the system shuts down.

NOTICE

This message occurs when the NVRAM battery capacity is below normal.

Correct any environmental problems, such as chassis over- temperature. The battery charges automatically. If the capacity is not restored automatically within 30 minutes after system power is on, replace the NVRAM battery within three months. If the problem persists, replace the FRU (field-replaceable unit) NVRAM card or PCM, where the battery is located.

The NVRAM battery capacity is below normal (%s).

reading (STRING): Reading that triggered this message.

INFORMATIONAL

This message occurs when the NVRAM battery capacity is normal.

(None).

The NVRAM battery capacity is normal.

(None).

ERROR

This message occurs when the NVRAM battery capacity is low. To prevent data loss, the system will schedule a clean chassis shutdown if the problem is not corrected.

Correct any environmental problems, such as chassis over- temperature. The battery charges automatically. If the capacity is not restored automatically within 30 minutes after system power is on, replace the NVRAM battery. If the problem persists, replace the FRU (field-replaceable unit) NVRAM card or PCM, where the battery is located.

The NVRAM battery capacity is low (%s).

reading (STRING): Reading that triggered this message.

INFORMATIONAL

This message occurs when the NVRAM battery charge FET is on.

(None).

The NVRAM battery charge FET is on.

(None).

ERROR

This message occurs when the NVRAM battery charge FET is off. To prevent data loss, the system will initiate a clean chassis shutdown if the problem is not corrected within 24 hours of first detection.

Shut down the system and power-cycle the controller. If the charge FET remains off, replace the NVRAM battery. If the problem persists, replace the FRU (field-replaceable unit) NVRAM card or PCM, where the battery is located.

The NVRAM battery charge FET is off. To prevent data loss, the system will shut down %s.

countdown (STRING): Remaining time before chassis shutdown.

EMERGENCY

This message occurs when the NVRAM battery is requesting to be charged but the charger is not charging the battery. To prevent data loss, the system will shut down.

Reseat the NVRAM battery connector. If the problem occurs again, replace the NVRAM battery. If the problem persists, replace the FRU (field-replaceable unit) NVRAM card or PCM, where the battery is located.

The NVRAM battery is requesting to be charged but the charger is not charging the battery. To prevent data loss, the system will shut down in %d minutes.

num_minutes (INT): Number of minutes until the system shuts down.

INFORMATIONAL

This message occurs when the NVRAM battery charging status is normal.

(None).

The NVRAM battery charging status is normal.

(None).

ERROR

This message occurs when the NVRAM battery charger is charging the battery even though the battery is not requesting to be charged. To prevent data loss, the system will initiate a clean chassis shutdown if the problem is not corrected within 24 hours of first detection.

Replace the NVRAM battery. If the problem persists, replace the FRU (field-replaceable unit) NVRAM card or PCM, where the battery is located.

The NVRAM battery charger is charging the battery even though the battery is not requesting to be charged. To prevent data loss, the system will shut down %s.

countdown (STRING): Remaining time before chassis shutdown.

EMERGENCY

This message occurs when the NVRAM battery charging current is critically high. To prevent data loss, the system will shut down.

Replace the NVRAM battery. If the problem persists, replace the FRU (field-replaceable unit) NVRAM card or PCM, where the battery is located.

The NVRAM battery current is critically high (%s). To prevent data loss, the system will shut down in %d minutes.

reading (STRING): Reading that triggered this message.
num_minutes (INT): Number of minutes until the system shuts down.

ERROR

This message occurs when the NVRAM battery charging current is above normal. To prevent data loss, the system will initiate a clean chassis shutdown if the problem is not corrected within 24 hours of first detection.

Replace the NVRAM battery. If the problem persists, replace the FRU (field-replaceable unit) NVRAM card or PCM, where the battery is located.

The NVRAM battery current is above normal (%s). To prevent data loss, the system will shut down %s.

reading (STRING): Reading that triggered this message.
countdown (STRING): Remaining time before chassis shutdown.

EMERGENCY

This message occurs when the NVRAM battery detects a short circuit. To prevent data loss, the system will shut down.

Contact NetApp technical support for assistance with identification and replacement of the appropriate component.

The NVRAM battery has a short circuit (%s). To prevent data loss, the system will shut down in %d minutes.

reading (STRING): Reading that triggered this message.
num_minutes (INT): Number of minutes until the system shuts down.

ERROR

This message occurs when the NVRAM battery is discharging when it should not. To prevent data loss, the system will initiate a clean chassis shutdown if the problem is not corrected within 24 hours of first detection.

Replace the NVRAM battery. If the problem persists, replace the FRU (field-replaceable unit) NVRAM card or PCM, where the battery is located.

The NVRAM battery current is below normal (%s). To prevent data loss, the system will shut down %s.

reading (STRING): Reading that triggered this message.
countdown (STRING): Remaining time before chassis shutdown.

INFORMATIONAL

This message occurs when the NVRAM battery current is normal.

(None).

The NVRAM battery current is normal.

(None).

INFORMATIONAL

This message occurs when the NVRAM battery discharge FET is on.

(None).

The NVRAM battery discharge FET is on.

(None).

EMERGENCY

This message occurs when the NVRAM battery discharge FET is off. To prevent data loss, the system will shut down.

Shut down the system and power-cycle the controller. If the discharge FET remains off, replace the NVRAM battery. If the problem persists, replace the FRU (field-replaceable unit) NVRAM card or PCM, where the battery is located.

The NVRAM battery discharge FET is off. To prevent data loss, the system will shut down in %d minutes.

num_minutes (INT): Number of minutes until the system shuts down.

INFORMATIONAL

This message occurs when the NVRAM battery-cycle count indicates that the battery has reached its anticipated life expectancy.

Replace the NVRAM battery in the next three months.

The NVRAM battery has reached its anticipated life expectancy.

(None).

INFORMATIONAL

This message occurs when the NVRAM battery-cycle count indicates that the battery is well below its anticipated life expectancy.

(None).

The NVRAM battery is well below its anticipated life expectancy.

(None).

EMERGENCY

This message occurs when the NVRAM battery is reporting a fatal fault condition. To prevent data loss, the system will shut down.

Correct any environmental problems, such as chassis over-temperature. If the battery still reports a fatal fault, replace the NVRAM battery. If the problem persists, replace the FRU (field-replaceable unit) NVRAM card or PCM, where the battery is located.

The NVRAM battery is reporting a fatal fault condition. To prevent data loss, the system will shut down in %d minutes.

num_minutes (INT): Number of minutes until the system shuts down.

INFORMATIONAL

This message occurs when the NVRAM battery internal fault condition has been cleared.

(None).

The NVRAM battery internal fault condition has been cleared.

(None).

NOTICE

This message occurs when the NVRAM battery is reporting a non-fatal fault condition.

Correct any environmental problems, such as chassis over- temperature. If the condition persists, replace the NVRAM battery in the next three months.

The NVRAM battery is reporting a non-fatal fault condition.

(None).

ERROR

This message occurs when the NVRAM battery full-charge capacity is low. To prevent data loss, the system will initiate a clean chassis shutdown if the problem is not corrected within 24 hours of first detection.

Use the "sysconfig -M" command in 7-Mode or the "run local sysconfig -M" command in clustered Data ONTAP® to get the battery manufacturer date. If the battery is newer than three years old, correct any chronic environmental problems, such as chassis over-temperature. Replace the NVRAM battery. If the problem persists, replace the FRU (field-replaceable unit) NVRAM card or PCM, where the battery is located.

The NVRAM battery full-charge capacity is low (%s). To prevent data loss, the system will shut down %s.

reading (STRING): Reading that triggered this message.
countdown (STRING): Remaining time before chassis shutdown.

Deprecated as of version 9.2.0 to address the EMS ID length violation.

EMERGENCY

This message occurs when the NVRAM battery full-charge capacity is critically low. To prevent data loss, the system will shut down.

Use the "sysconfig -M" command in 7-Mode or the "run local sysconfig -M" command in clustered Data ONTAP® to get the battery manufacturer date. If the battery is newer than three years old, correct any chronic environmental problems, such as chassis over-temperature. Replace the NVRAM battery. If the problem persists, replace the FRU (field-replaceable unit) NVRAM card or PCM, where the battery is located.

The NVRAM battery full-charge capacity is critically low (%s). To prevent data loss, the system will shut down in %d minutes.

reading (STRING): Reading that triggered this message.
num_minutes (INT): Number of minutes until the system shuts down.

NOTICE

This message occurs when the NVRAM battery full-charge capacity is below normal.

Replace the NVRAM battery in the next three months. Use the "sysconfig -M" command in 7-Mode or the "run local sysconfig -M" command in clustered Data ONTAP® to get the battery manufacturer date. If the battery is newer than three years old, correct any chronic environmental problems, such as chassis over-temperature.

The NVRAM battery full-charge capacity is below normal (%s).

reading (STRING): Reading that triggered this message.

INFORMATIONAL

This message occurs when the NVRAM battery full-charge capacity is normal.

(None).

The NVRAM battery full-charge capacity is normal.

(None).

EMERGENCY

This message occurs when the NVRAM battery full-charge capacity is critically low. To prevent data loss, the system will shut down.

Use the "system node run -node local sysconfig -M" command to obtain the battery manufacturing date. If the battery is over three years old, replacement might be necessary. Contact NetApp technical support for troubleshooting assistance.

The NVRAM battery full-charge capacity is critically low (%s). To prevent data loss, the system will shut down in %d minutes.

reading (STRING): Reading that triggered this message.
num_minutes (INT): Number of minutes until the system shuts down.

NOTICE

This message occurs when the NVRAM battery fast-charge timeout expires. The battery will not be charged until this condition is corrected.

Shut down the controller and power cycle it from the Service Processor (SP) command line interface (CLI) with the "system power cycle" command. The fast-charge timeout will be reset after the power cycle.

The NVRAM battery has reached a charging timeout fault. The battery charger will not turn on again until the contoller has been power cycled. Low capacity warning messages begin in %s weeks.

num_weeks (STRING): Number of weeks before low capacity warning messages begin.

EMERGENCY

This message occurs when the NVRAM battery is not present. To prevent data loss, the system will shut down.

While the system is shut down, pull the controller from the slot and ensure that the NVRAM battery is present. If the NVRAM battery is already present, ensure that the connector is seated properly. Push the controller back in and power on the system. If this does not correct the problem, replace the NVRAM battery. If the system still does not detect the battery, replace either the field-replaceable unit (FRU) NVRAM card or the Plus-CPU Module (PCM), where the battery is located.

The NVRAM battery is not present. To prevent data loss, the system will shut down in %d minutes.

num_minutes (INT): Number of minutes until the system shuts down.

ERROR

This message occurs when an unsupported NVRAM battery pack is installed in the system. To prevent data loss, the system initiates a clean chassis shutdown if the problem is not corrected within 24 hours of first detection.

Shut down the system and replace the NVRAM battery with a correct battery pack.

The incorrect NVRAM battery is installed. Expected part number is %s. To prevent data loss, the system will shut down in %d minutes.

partnum (STRING): Valid battery part number.
num_minutes (INT): Number of minutes until the system shuts down.

INFORMATIONAL

This message occurs when a valid NVRAM battery pack is now present and readable.

(None).

A valid NVRAM battery pack is present.

(None).

EMERGENCY

This message occurs when the NVRAM battery is not receiving power. To prevent data loss, the system will shut down.

Pull the controller from the slot and ensure that the NVRAM battery connector is seated properly. Push the controller back in and boot up the system. If the NVRAM battery is still not receiving power, replace the NVRAM battery. If the problem persists, replace the FRU (field-replaceable unit) NVRAM card or PCM, where the battery is located.

The NVRAM battery is not receiving power. To prevent data loss, the system will shut down in %d minutes.

num_minutes (INT): Number of minutes until the system shuts down.

INFORMATIONAL

This message occurs when the NVRAM battery power is normal.

(None).

The NVRAM battery power is normal.

(None).

EMERGENCY

This message occurs when the NVRAM battery state cannot be determined because the sensor is unreadable. To prevent data loss, the system will shut down.

Pull the controller from the slot and ensure that the NVRAM battery connector is seated properly. Push the controller back in and power on the system. If the problem is not corrected, replace the NVRAM battery. If the sensor is still not readable, replace the FRU (field-replaceable unit) NVRAM card or PCM, where the battery is located.

The NVRAM battery state cannot be determined because the '%s' sensor is unreadable. To prevent data loss, the system will shut down in %d minutes.

sensor_name (STRING): Sensor name.
num_minutes (INT): Number of minutes until the system shuts down.

EMERGENCY

This message occurs when the NVRAM battery temperature is critically high. To prevent data loss, the system will shut down.

Correct any environmental issues, such as a high ambient temperature. If the NVRAM battery temperature is still above normal, replace the NVRAM battery. If the problem persists, replace the FRU (field-replaceable unit) NVRAM card or PCM, where the battery is located.

The NVRAM battery temperature is critically high (%s). To prevent data loss, the system will shut down in %d minutes.

reading (STRING): Reading that triggered this message.
num_minutes (INT): Number of minutes until the system shuts down.

NOTICE

This message occurs when the NVRAM battery temperature is above normal. Battery life will be severely compromised.

Correct any environmental issues, such as a high ambient temperature. If the NVRAM battery temperature is still above normal, replace the NVRAM battery. If the problem persists, replace the FRU (field-replaceable unit) NVRAM card or PCM, where the battery is located.

The NVRAM battery temperature is above normal (%s).

reading (STRING): Reading that triggered this message.

ERROR

This message occurs when the NVRAM battery is too cold. To prevent data loss, the system will initiate a clean chassis shutdown if the problem is not corrected within 24 hours of first detection.

If the system is excessively cold, allow it to warm gradually. If the NVRAM battery temperature is still too low, replace the NVRAM battery. If the problem persists, replace the FRU (field-replaceable unit) NVRAM card or PCM, where the battery is located.

The NVRAM battery is too cold (%s). To prevent data loss, the system will shut down %s.

reading (STRING): Reading that triggered this message.
countdown (STRING): Remaining time before chassis shutdown.

NOTICE

This message occurs when the NVRAM battery temperature is below normal.

Allow the system to warm gradually. If the NVRAM battery temperature is still low, replace the NVRAM battery. If the problem persists, replace the FRU (field-replaceable unit) NVRAM card or PCM, where the battery is located.

The NVRAM battery temperature is below normal (%s).

reading (STRING): Reading that triggered this message.

INFORMATIONAL

This message occurs when the NVRAM battery temperature is normal.

(None).

The NVRAM battery temperature is normal.

(None).

EMERGENCY

This message occurs when the NVRAM battery voltage is critically high. To prevent data loss, the system will shut down.

Replace the NVRAM battery. If the problem persists, replace the FRU (field-replaceable unit) NVRAM card or PCM, where the battery is located.

The NVRAM battery voltage is critically high (%s). To prevent data loss, the system will shut down in %d minutes.

reading (STRING): Reading that triggered this message.
num_minutes (INT): Number of minutes until the system shuts down.

ERROR

This message occurs when the NVRAM battery voltage is above normal. To prevent data loss, the system will initiate a clean chassis shutdown if the problem is not corrected within 24 hours of first detection.

Correct any environmental problems, such as chassis over- temperature. If the NVRAM battery voltage is still above normal, replace the NVRAM battery. If the problem returns or persists, replace the FRU (field-replaceable unit) NVRAM card or PCM, where the battery is located.

The NVRAM battery voltage is above normal (%s). To prevent data loss, the system will shut down %s.

reading (STRING): Reading that triggered this message.
countdown (STRING): Remaining time before chassis shutdown.

EMERGENCY

This message occurs when the NVRAM battery voltage is critically low. To prevent data loss, the system will shut down.

Correct any environmental problems, such as chassis over- temperature. If the NVRAM battery voltage is still critically low, replace the NVRAM battery. If the problem persists, replace the FRU (field-replaceable unit) NVRAM card or PCM, where the battery is located.

The NVRAM battery voltage is critically low (%s). To prevent data loss, the system will shut down in %d minutes.

reading (STRING): Reading that triggered this message.
num_minutes (INT): Number of minutes until the system shuts down.

INFORMATIONAL

This message occurs when the NVRAM battery voltage is normal.

(None).

The NVRAM battery voltage is normal.

(None).

ERROR

This message occurs when the NVRAM battery voltage is below normal. To prevent data loss, the system will schedule a clean chassis shutdown if the problem is not corrected.

Correct any environmental problems, such as chassis over- temperature. If the NVRAM battery voltage is still below normal 30 minutes after environmental problems have been corrected, replace the NVRAM battery. If the problem persists, replace the FRU (field-replaceable unit) NVRAM card or PCM, where the battery is located.

The NVRAM battery voltage is below normal (%s).

reading (STRING): Reading that triggered this message.