Skip to main content
ONTAP MetroCluster
本繁體中文版使用機器翻譯,譯文僅供參考,若與英文版本牴觸,應以英文版本為準。

變更 FC 交換器的廠商或型號

貢獻者

您可能需要將 FC 交換器的廠商從 Cisco 變更為 Brocade 、或是反之、變更交換器模式或兩者都變更。

關於這項工作
  • 此程序適用於使用 NetApp 驗證交換器的情況。

  • 對於組態中的兩個 Fabric 、您必須一次在一個 Fabric 上執行本程序中的步驟。

步驟
  1. [[Step_1 、 Step 1]] 檢查組態的健全狀況。

    1. 檢查MetroCluster 每個叢集上的「* MetroCluster 」「」「」「顯示*」是否已設定成正常模式

      cluster_A::> metrocluster show
      Cluster                   Entry Name          State
      ------------------------- ------------------- -----------
       Local: cluster_A         Configuration state configured
                                Mode                normal
                                AUSO Failure Domain auso-on-cluster-disaster
      Remote: cluster_B         Configuration state configured
                                Mode                normal
                                AUSO Failure Domain auso-on-cluster-disaster
    2. 檢查是否在每個節點上啟用鏡射:「* MetroCluster 鏡射節點show *」

      cluster_A::> metrocluster node show
      DR                           Configuration  DR
      Group Cluster Node           State          Mirroring Mode
      ----- ------- -------------- -------------- --------- --------------------
      1     cluster_A
                    node_A_1       configured     enabled   normal
            cluster_B
                    node_B_1       configured     enabled   normal
      2 entries were displayed.
    3. 請檢查MetroCluster 這些元件是否健全:「* MetroCluster 《不實檢查路跑

      cluster_A::> metrocluster check run
      
      Last Checked On: 10/1/2014 16:03:37
      
      Component           Result
      ------------------- ---------
      nodes               ok
      lifs                ok
      config-replication  ok
      aggregates          ok
      4 entries were displayed.
      
      Command completed. Use the "metrocluster check show -instance" command or sub-commands in "metrocluster check" directory for detailed results.
      To check if the nodes are ready to do a switchover or switchback operation, run "metrocluster switchover -simulate" or "metrocluster switchback -simulate", respectively.
    4. 檢查是否沒有健全狀況警示:「系統健全狀況警示顯示

  2. 安裝前請先設定新交換器。

    請依照中的步驟進行 "設定FC交換器"

  3. 按照下列順序移除連線、以中斷舊交換器的連線:

    1. 如果本機叢集介面已連線至交換器:

      1. 拔下本機叢集介面

      2. 中斷本機叢集 ISL 的連線

    2. 拔下 MetroCluster FC 介面。

    3. 中斷 MetroCluster ISL 的連線。

  4. 關閉舊交換器電源、拔下纜線、然後以新交換器實際更換舊交換器。

  5. 依下列順序連接交換器:

    您必須遵循中的步驟 "安裝 MetroCluster 元件並連接纜線"

    1. 將 ISL 連接到遠端站台。

    2. 連接 MetroCluster FC 介面。

    3. 連接本機叢集介面。

      如果本機叢集介面已連線至交換器:

      1. 連接本機叢集介面。

      2. 連接本機叢集 ISL 。

  6. 開啟交換器電源。

  7. 重複、確認 MetroCluster 組態正常 [步驟1.]

  8. 針對組態中的第二個 Fabric 重複步驟 1 至步驟 7 。