Skip to main content
本繁體中文版使用機器翻譯，譯文僅供參考，若與英文版本牴觸，應以英文版本為準。

設定 Cisco Nexus 92300YC 叢集交換器

貢獻者 netapp-jsnyder netapp-yvonneo netapp-jolieg
PDF

使用初始設定指令設定 Cisco Nexus 92300YC 叢集交換器，使其做好叢集運作的準備。

步驟

  1. 將串口連接到主機或串列埠。

  2. 將管理連接埠（交換器的非連接埠側）連接到 SFTP 伺服器所在的相同網路。

  3. 在控制台上，設定主機端串列埠設定：

    • 9600 baud

    • 8 位元數據

    • 1 停止位

    • 奇偶性：無

    • 流量控制：無

  4. 首次開機或在清除執行中組態後重新開機時，Nexus 92300YC 交換器會陷入開機循環。輸入 yes 可中斷此循環，從而中止 Power on Auto Provisioning。

    顯示系統管理員帳戶設定。

    顯示範例 
    $ VDC-1 %$ %POAP-2-POAP_INFO:   - Abort Power On Auto Provisioning [yes - continue with normal setup, skip - bypass password and basic configuration, no - continue with Power On Auto Provisioning] (yes/skip/no)[no]: y
Disabling POAP.......Disabling POAP
2019 Apr 10 00:36:17 switch %$ VDC-1 %$ poap: Rolling back, please wait... (This may take 5-15 minutes)

          ---- System Admin Account Setup ----

Do you want to enforce secure password standard (yes/no) [y]:

  5. 輸入 y 強制執行安全的密碼標準：

    Do you want to enforce secure password standard (yes/no) [y]: y

  6. 請輸入並確認管理者使用者的密碼：

    Enter the password for "admin":
Confirm the password for "admin":

  7. 輸入 yes 進入基本系統組態對話框。

    顯示範例 
    This setup utility will guide you through the basic configuration of
the system. Setup configures only enough connectivity for management
of the system.

Please register Cisco Nexus9000 Family devices promptly with your
supplier. Failure to register may affect response times for initial
service calls. Nexus9000 devices must be registered to receive
entitled support services.

Press Enter at anytime to skip a dialog. Use ctrl-c at anytime
to skip the remaining dialogs.

Would you like to enter the basic configuration dialog (yes/no):

  8. 建立另一個登入帳戶：

    Create another login account (yes/no) [n]:

  9. 設定唯讀和讀寫 SNMP 團體字串：

    Configure read-only SNMP community string (yes/no) [n]:

Configure read-write SNMP community string (yes/no) [n]:

  10. 設定叢集交換器名稱：

    Enter the switch name : cs2

  11. 設定帶外管理介面：

    Continue with Out-of-band (mgmt0) management configuration? (yes/no) [y]: y

Mgmt0 IPv4 address : 172.22.133.216

Mgmt0 IPv4 netmask : 255.255.224.0

Configure the default gateway? (yes/no) [y]: y

IPv4 address of the default gateway : 172.22.128.1

  12. 設定進階 IP 選項：

    Configure advanced IP options? (yes/no) [n]: n

  13. 設定 Telnet 服務：

    Enable the telnet service? (yes/no) [n]: n

  14. 設定 SSH 服務和 SSH 金鑰：

    Enable the ssh service? (yes/no) [y]: y

       Type of ssh key you would like to generate (dsa/rsa) [rsa]: rsa

       Number of rsa key bits <1024-2048> [1024]: 2048

  15. 設定其他設定：

    Configure the ntp server? (yes/no) [n]: n

  Configure default interface layer (L3/L2) [L2]: L2

  Configure default switchport interface state (shut/noshut) [noshut]: noshut

  Configure CoPP system profile (strict/moderate/lenient/dense) [strict]: strict

  16. 確認交換器資訊並儲存組態：

    Would you like to edit the configuration? (yes/no) [n]: n

Use this configuration and save it? (yes/no) [y]: y

[] 100%
Copy complete, now saving to disk (please wait)...
Copy complete.
下一步是什麼？

配置好交換器後，您可以"準備安裝NX-OS軟體和RCF"。