開始使用
本繁體中文版使用機器翻譯，譯文僅供參考，若與英文版本牴觸，應以英文版本為準。
準備安裝NX-OS軟體和RCF
貢獻者
建議變更
PDF
在安裝NX-OS軟體和參考組態檔（RCF）之前、請遵循此程序。
關於範例
本程序中的範例使用下列交換器和節點命名法：
-
兩個Cisco交換器的名稱為CS1和CS2。
-
節點名稱為cluster1-01和cluster1-02。
-
叢集LIF名稱為cluster1-01_clus1、cluster1-01_clus2（叢集1-01）和cluster1-02_clus2（叢集1-01）、cluster1-02_clus2（叢集1-02）。
-
「cluster1：*：>」提示會指出叢集的名稱。
關於這項工作
此程序需要同時使用ONTAP 支援指令和Cisco Nexus 9000系列交換器的指令；ONTAP 除非另有說明、否則會使用支援指令。
步驟
-
如果AutoSupport 此叢集啟用了「支援功能」、請叫用AutoSupport 下列訊息來抑制自動建立案例：「System Node AutoSupport Rsepooke -Node *-type all -most MAn=x h」
其中x是維護時段的持續時間（以小時為單位）。
此資訊可通知技術支援人員執行此維護工作、以便在維護期間抑制自動建立案例。AutoSupport -
將權限等級變更為進階、並在系統提示您繼續時輸入* y*：
"進階權限"
出現進階提示（「*>」）。
-
顯示每個叢集互連交換器的每個節點已設定多少個叢集互連介面：
「network device-dDiscovery show -protocol cup」
顯示範例
cluster1::*> network device-discovery show -protocol cdp Node/ Local Discovered Protocol Port Device (LLDP: ChassisID) Interface Platform ----------- ------ ------------------------- ----------------- -------- cluster1-02/cdp e0a cs1 Eth1/2 N9K-C9336C e0b cs2 Eth1/2 N9K-C9336C cluster1-01/cdp e0a cs1 Eth1/1 N9K-C9336C e0b cs2 Eth1/1 N9K-C9336C 4 entries were displayed. -
檢查每個叢集介面的管理或作業狀態。
-
顯示網路連接埠屬性：
`network port show –ipspace Cluster`
顯示範例
cluster1::*> network port show -ipspace Cluster Node: cluster1-02 Speed(Mbps) Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status --------- ------------ ---------------- ---- ---- ----------- ------ e0a Cluster Cluster up 9000 auto/10000 healthy e0b Cluster Cluster up 9000 auto/10000 healthy Node: cluster1-01 Speed(Mbps) Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status --------- ------------ ---------------- ---- ---- ----------- ------ e0a Cluster Cluster up 9000 auto/10000 healthy e0b Cluster Cluster up 9000 auto/10000 healthy 4 entries were displayed. -
顯示關於生命的資訊：
「網路介面show -vserver叢集」
顯示範例
cluster1::*> network interface show -vserver Cluster Logical Status Network Current Current Is Vserver Interface Admin/Oper Address/Mask Node Port Home ----------- ------------------ ---------- ------------------ ------------- ------- ---- Cluster cluster1-01_clus1 up/up 169.254.209.69/16 cluster1-01 e0a true cluster1-01_clus2 up/up 169.254.49.125/16 cluster1-01 e0b true cluster1-02_clus1 up/up 169.254.47.194/16 cluster1-02 e0a true cluster1-02_clus2 up/up 169.254.19.183/16 cluster1-02 e0b true 4 entries were displayed. -
-
Ping遠端叢集LIF：
「叢集ping叢集節點節點名稱」
顯示範例
cluster1::*> cluster ping-cluster -node cluster1-02 Host is cluster1-02 Getting addresses from network interface table... Cluster cluster1-01_clus1 169.254.209.69 cluster1-01 e0a Cluster cluster1-01_clus2 169.254.49.125 cluster1-01 e0b Cluster cluster1-02_clus1 169.254.47.194 cluster1-02 e0a Cluster cluster1-02_clus2 169.254.19.183 cluster1-02 e0b Local = 169.254.47.194 169.254.19.183 Remote = 169.254.209.69 169.254.49.125 Cluster Vserver Id = 4294967293 Ping status: Basic connectivity succeeds on 4 path(s) Basic connectivity fails on 0 path(s) Detected 9000 byte MTU on 4 path(s): Local 169.254.19.183 to Remote 169.254.209.69 Local 169.254.19.183 to Remote 169.254.49.125 Local 169.254.47.194 to Remote 169.254.209.69 Local 169.254.47.194 to Remote 169.254.49.125 Larger than PMTU communication succeeds on 4 path(s) RPC status: 2 paths up, 0 paths down (tcp check) 2 paths up, 0 paths down (udp check) -
驗證是否已在所有叢集生命體上啟用自動還原命令：
「網路介面show -vserver叢集-功能 變數自動回復」
顯示範例
cluster1::*> network interface show -vserver Cluster -fields auto-revert Logical Vserver Interface Auto-revert --------- ––––––-------------- ------------ Cluster cluster1-01_clus1 true cluster1-01_clus2 true cluster1-02_clus1 true cluster1-02_clus2 true 4 entries were displayed. -
對於更新版本的支援、請使用下列命令啟用乙太網路交換器健全狀況監視器記錄收集功能、以收集交換器相關的記錄檔ONTAP ：
「系統交換器乙太網路記錄設定密碼」和「系統交換器乙太網路記錄啟用-收集」
顯示範例
cluster1::*> system switch ethernet log setup-password Enter the switch name: <return> The switch name entered is not recognized. Choose from the following list: cs1 cs2 cluster1::*> system switch ethernet log setup-password Enter the switch name: cs1 RSA key fingerprint is e5:8b:c6:dc:e2:18:18:09:36:63:d9:63:dd:03:d9:cc Do you want to continue? {y|n}::[n] y Enter the password: <enter switch password> Enter the password again: <enter switch password> cluster1::*> system switch ethernet log setup-password Enter the switch name: cs2 RSA key fingerprint is 57:49:86:a1:b9:80:6a:61:9a:86:8e:3c:e3:b7:1f:b1 Do you want to continue? {y|n}:: [n] y Enter the password: <enter switch password> Enter the password again: <enter switch password> cluster1::*> system switch ethernet log enable-collection Do you want to enable cluster log collection for all nodes in the cluster? {y|n}: [n] y Enabling cluster switch log collection. cluster1::*>
如果這些命令中有任何一個出現錯誤、請聯絡NetApp支援部門。 -
針對發行9.5P16、9.6P12及9.7P10及更新版本的修補程式、請使用下列命令啟用乙太網路交換器健全狀況監視器記錄收集功能、以收集交換器相關的記錄檔ONTAP ：
「系統叢集交換器記錄設定密碼」和「系統叢集交換器記錄啟用收集」
顯示範例
cluster1::*> system cluster-switch log setup-password Enter the switch name: <return> The switch name entered is not recognized. Choose from the following list: cs1 cs2 cluster1::*> system cluster-switch log setup-password Enter the switch name: cs1 RSA key fingerprint is e5:8b:c6:dc:e2:18:18:09:36:63:d9:63:dd:03:d9:cc Do you want to continue? {y|n}::[n] y Enter the password: <enter switch password> Enter the password again: <enter switch password> cluster1::*> system cluster-switch log setup-password Enter the switch name: cs2 RSA key fingerprint is 57:49:86:a1:b9:80:6a:61:9a:86:8e:3c:e3:b7:1f:b1 Do you want to continue? {y|n}:: [n] y Enter the password: <enter switch password> Enter the password again: <enter switch password> cluster1::*> system cluster-switch log enable-collection Do you want to enable cluster log collection for all nodes in the cluster? {y|n}: [n] y Enabling cluster switch log collection. cluster1::*>
|
|
如果這些命令中有任何一個出現錯誤、請聯絡NetApp支援部門。 |
接下來呢？