Skip to main content
Cluster and storage switches
Se proporciona el idioma español mediante traducción automática para su comodidad. En caso de alguna inconsistencia, el inglés precede al español.

Instale el software NX-OS

Colaboradores
PDF

Puede utilizar este procedimiento para instalar el software NX-OS en el switch de clúster Nexus 3232C.

Revise los requisitos

Antes de empezar

  • Una copia de seguridad actual de la configuración del switch.

  • Un clúster en pleno funcionamiento (sin errores en los registros o problemas similares).

  • "Página del switch Cisco Ethernet". Consulte en la tabla de compatibilidad del switch las versiones ONTAP y NX-OS compatibles.

  • "Switches Cisco Nexus serie 3000". Consulte las guías de software y actualización adecuadas disponibles en el sitio web de Cisco para obtener documentación completa sobre los procedimientos de actualización y degradación de switches de Cisco.

Instale el software

Para ello, es necesario utilizar tanto comandos de la ONTAP como comandos de la serie Cisco Nexus 3000; los comandos de la ONTAP se usan a menos que se indique lo contrario.

Asegúrese de completar el procedimiento en "Prepare la instalación de NX-OS y RCF"y, a continuación, siga los pasos que se indican a continuación.

Pasos

  1. Conecte el switch de clúster a la red de gestión.

  2. Utilice la ping Comando para verificar la conectividad con el servidor que aloja el software NX-OS y el RCF.

    Muestra el ejemplo

    Este ejemplo verifica que el switch puede llegar al servidor en la dirección IP 172.19.2.1:

    cs2# ping 172.19.2.1
Pinging 172.19.2.1 with 0 bytes of data:

Reply From 172.19.2.1: icmp_seq = 0. time= 5910 usec.

  3. Muestre los puertos del clúster en cada nodo que están conectados a los switches de clúster:

    network device-discovery show

    Muestra el ejemplo 
    cluster1::*> network device-discovery show
Node/       Local  Discovered
Protocol    Port   Device (LLDP: ChassisID)  Interface         Platform
----------- ------ ------------------------- ----------------  ----------
cluster1-01/cdp
            e0a    cs1                       Ethernet1/7       N3K-C3232C
            e0d    cs2                       Ethernet1/7       N3K-C3232C
cluster1-02/cdp
            e0a    cs1                       Ethernet1/8       N3K-C3232C
            e0d    cs2                       Ethernet1/8       N3K-C3232C
cluster1-03/cdp
            e0a    cs1                       Ethernet1/1/1     N3K-C3232C
            e0b    cs2                       Ethernet1/1/1     N3K-C3232C
cluster1-04/cdp
            e0a    cs1                       Ethernet1/1/2     N3K-C3232C
            e0b    cs2                       Ethernet1/1/2     N3K-C3232C
cluster1::*>

  4. Compruebe el estado administrativo y operativo de cada puerto del clúster.

    1. Compruebe que todos los puertos del clúster están up con un estado correcto:

      network port show -role cluster

      Muestra el ejemplo 
      cluster1::*> network port show -role cluster

Node: cluster1-01
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e0a       Cluster      Cluster          up   9000  auto/100000 healthy false
e0d       Cluster      Cluster          up   9000  auto/100000 healthy false

Node: cluster1-02
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e0a       Cluster      Cluster          up   9000  auto/100000 healthy false
e0d       Cluster      Cluster          up   9000  auto/100000 healthy false
8 entries were displayed.

Node: cluster1-03

   Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e0a       Cluster      Cluster          up   9000  auto/10000 healthy  false
e0b       Cluster      Cluster          up   9000  auto/10000 healthy  false

Node: cluster1-04
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e0a       Cluster      Cluster          up   9000  auto/10000 healthy  false
e0b       Cluster      Cluster          up   9000  auto/10000 healthy  false
cluster1::*>

    2. Compruebe que todas las interfaces del clúster (LIF) están en el puerto de inicio:

      network interface show -role cluster

      Muestra el ejemplo 
      cluster1::*> network interface show -role cluster
            Logical            Status     Network           Current      Current Is
Vserver     Interface          Admin/Oper Address/Mask      Node         Port    Home
----------- ------------------ ---------- ----------------- ------------ ------- ----
Cluster
            cluster1-01_clus1  up/up     169.254.3.4/23     cluster1-01  e0a     true
            cluster1-01_clus2  up/up     169.254.3.5/23     cluster1-01  e0d     true
            cluster1-02_clus1  up/up     169.254.3.8/23     cluster1-02  e0a     true
            cluster1-02_clus2  up/up     169.254.3.9/23     cluster1-02  e0d     true
            cluster1-03_clus1  up/up     169.254.1.3/23     cluster1-03  e0a     true
            cluster1-03_clus2  up/up     169.254.1.1/23     cluster1-03  e0b     true
            cluster1-04_clus1  up/up     169.254.1.6/23     cluster1-04  e0a     true
            cluster1-04_clus2  up/up     169.254.1.7/23     cluster1-04  e0b     true
8 entries were displayed.
cluster1::*>

    3. Compruebe que el clúster muestra información de ambos switches de clúster:

      system cluster-switch show -is-monitoring-enabled-operational true

    Muestra el ejemplo 
    cluster1::*> system cluster-switch show -is-monitoring-enabled-operational true
Switch                      Type               Address          Model
--------------------------- ------------------ ---------------- ----------
cs1                         cluster-network    10.233.205.90    N3K-C3232C
     Serial Number: FOCXXXXXXGD
      Is Monitored: true
            Reason: None
  Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                    9.3(5)
    Version Source: CDP

cs2                         cluster-network    10.233.205.91    N3K-C3232C
     Serial Number: FOCXXXXXXGS
      Is Monitored: true
            Reason: None
  Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                    9.3(5)
    Version Source: CDP
cluster1::*>

  5. Deshabilite la reversión automática en las LIF del clúster. Los LIF de clúster conmutan al switch del clúster asociado y permanecen allí mientras realiza el procedimiento de actualización en el switch de destino:

    network interface modify -vserver Cluster -lif * -auto-revert false

  6. Copie las imágenes del software NX-OS y EPLD en el switch Nexus 3232C.

    Muestra el ejemplo 
    cs2# copy sftp: bootflash: vrf management
Enter source filename: /code/nxos.9.3.4.bin
Enter hostname for the sftp server: 172.19.2.1
Enter username: user1

Outbound-ReKey for 172.19.2.1:22
Inbound-ReKey for 172.19.2.1:22
user1@172.19.2.1's password:
sftp> progress
Progress meter enabled
sftp> get   /code/nxos.9.3.4.bin  /bootflash/nxos.9.3.4.bin
/code/nxos.9.3.4.bin  100% 1261MB   9.3MB/s   02:15
sftp> exit
Copy complete, now saving to disk (please wait)...
Copy complete.


cs2# copy sftp: bootflash: vrf management
Enter source filename: /code/n9000-epld.9.3.4.img
Enter hostname for the sftp server: 172.19.2.1
Enter username: user1

Outbound-ReKey for 172.19.2.1:22
Inbound-ReKey for 172.19.2.1:22
user1@172.19.2.1's password:
sftp> progress
Progress meter enabled
sftp> get   /code/n9000-epld.9.3.4.img  /bootflash/n9000-epld.9.3.4.img
/code/n9000-epld.9.3.4.img  100%  161MB   9.5MB/s   00:16
sftp> exit
Copy complete, now saving to disk (please wait)...
Copy complete.

  7. Compruebe la versión que se está ejecutando del software NX-OS:

    show version

    Muestra el ejemplo 
    cs2# show version
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (C) 2002-2019, Cisco and/or its affiliates.
All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under their own
licenses, such as open source.  This software is provided "as is," and unless
otherwise stated, there is no warranty, express or implied, including but not
limited to warranties of merchantability and fitness for a particular purpose.
Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or
GNU General Public License (GPL) version 3.0  or the GNU
Lesser General Public License (LGPL) Version 2.1 or
Lesser General Public License (LGPL) Version 2.0.
A copy of each such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://opensource.org/licenses/gpl-3.0.html and
http://www.opensource.org/licenses/lgpl-2.1.php and
http://www.gnu.org/licenses/old-licenses/library.txt.

Software
  BIOS: version 08.37
  NXOS: version 9.3(3)
  BIOS compile time:  01/28/2020
  NXOS image file is: bootflash:///nxos.9.3.3.bin
  NXOS compile time:  12/22/2019 2:00:00 [12/22/2019 14:00:37]

Hardware
  cisco Nexus3000 C3232C Chassis (Nexus 9000 Series)
  Intel(R) Xeon(R) CPU E5-2403 v2 @ 1.80GHz with 8154432 kB of memory.
  Processor Board ID FOCXXXXXXGD

  Device name: cs2
  bootflash:   53298520 kB
Kernel uptime is 0 day(s), 0 hour(s), 3 minute(s), 36 second(s)

Last reset at 74117 usecs after Tue Nov 24 06:24:23 2020
  Reason: Reset Requested by CLI command reload
  System version: 9.3(3)
  Service:

plugin
  Core Plugin, Ethernet Plugin

Active Package(s):

cs2#

  8. Instale la imagen NX-OS.

    La instalación del archivo de imagen hace que se cargue cada vez que se reinicia el conmutador.

    Muestra el ejemplo 
    cs2# install all nxos bootflash:nxos.9.3.4.bin
Installer will perform compatibility check first. Please wait.
Installer is forced disruptive

Verifying image bootflash:/nxos.9.3.4.bin for boot variable "nxos".
[] 100% -- SUCCESS

Verifying image type.
[] 100% -- SUCCESS

Preparing "nxos" version info using image bootflash:/nxos.9.3.4.bin.
[] 100% -- SUCCESS

Preparing "bios" version info using image bootflash:/nxos.9.3.4.bin.
[] 100% -- SUCCESS

Performing module support checks.
[] 100% -- SUCCESS

Notifying services about system upgrade.
[] 100% -- SUCCESS


Compatibility check is done:
Module  bootable          Impact              Install-type  Reason
------- ----------------- ------------------- ------------- ----------
     1     Yes            Disruptive          Reset         Default upgrade is not hitless


Images will be upgraded according to following table:
Module       Image       Running-Version(pri:alt)                New-Version          Upg-Required
------------ ----------- --------------------------------------- -------------------- ------------
     1       nxos        9.3(3)                                  9.3(4)               yes
     1       bios        v08.37(01/28/2020):v08.32(10/18/2016)   v08.37(01/28/2020)   no


Switch will be reloaded for disruptive upgrade.
Do you want to continue with the installation (y/n)?  [n] y

Install is in progress, please wait.

Performing runtime checks.
[] 100% -- SUCCESS

Setting boot variables.
[] 100% -- SUCCESS

Performing configuration copy.
[] 100% -- SUCCESS

Module 1: Refreshing compact flash and upgrading bios/loader/bootrom.
Warning: please do not remove or power off the module at this time.
[] 100% -- SUCCESS


Finishing the upgrade, switch will reboot in 10 seconds.
cs2#

  9. Compruebe la nueva versión del software NX-OS una vez que se haya reiniciado el switch:

    show version

    Muestra el ejemplo 
    cs2# show version
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (C) 2002-2020, Cisco and/or its affiliates.
All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under their own
licenses, such as open source.  This software is provided "as is," and unless
otherwise stated, there is no warranty, express or implied, including but not
limited to warranties of merchantability and fitness for a particular purpose.
Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or
GNU General Public License (GPL) version 3.0  or the GNU
Lesser General Public License (LGPL) Version 2.1 or
Lesser General Public License (LGPL) Version 2.0.
A copy of each such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://opensource.org/licenses/gpl-3.0.html and
http://www.opensource.org/licenses/lgpl-2.1.php and
http://www.gnu.org/licenses/old-licenses/library.txt.

Software
  BIOS: version 08.37
  NXOS: version 9.3(4)
  BIOS compile time:  01/28/2020
  NXOS image file is: bootflash:///nxos.9.3.4.bin
  NXOS compile time:  4/28/2020 21:00:00 [04/29/2020 06:28:31]

Hardware
 cisco Nexus3000 C3232C Chassis (Nexus 9000 Series)
  Intel(R) Xeon(R) CPU E5-2403 v2 @ 1.80GHz with 8154432 kB of memory.
  Processor Board ID FOCXXXXXXGS

  Device name: rtpnpi-mcc01-8200-ms-A1
  bootflash:   53298520 kB
Kernel uptime is 0 day(s), 0 hour(s), 3 minute(s), 14 second(s)

Last reset at 196755 usecs after Tue Nov 24 06:37:36 2020
  Reason: Reset due to upgrade
  System version: 9.3(3)
  Service:

plugin
  Core Plugin, Ethernet Plugin

Active Package(s):

cs2#

  10. Actualice la imagen de EPLD y reinicie el switch.

    Muestra el ejemplo 
    cs2# show version module 1 epld

EPLD Device                     Version
---------------------------------------
MI   FPGA                       0x12
IO   FPGA                       0x11

cs2# install epld bootflash:n9000-epld.9.3.4.img module 1
Compatibility check:
Module        Type         Upgradable    Impact      Reason
------  -----------------  ----------    ----------  -----------------
     1         SUP         Yes           Disruptive  Module Upgradable

Retrieving EPLD versions.... Please wait.
Images will be upgraded according to following table:
Module  Type   EPLD              Running-Version   New-Version  Upg-Required
------  ----  -----------------  ---------------   -----------  ------------
     1   SUP   MI FPGA                0x12         0x12         No
     1   SUP   IO FPGA                0x11         0x12         Yes
The above modules require upgrade.
The switch will be reloaded at the end of the upgrade
Do you want to continue (y/n) ?  [n] y

Proceeding to upgrade Modules.

Starting Module 1 EPLD Upgrade

Module 1 : IO FPGA [Programming] : 100.00% (     64 of      64 sectors)
Module 1 EPLD upgrade is successful.
Module        Type  Upgrade-Result
------  ------------------  --------------
     1         SUP         Success

Module 1 EPLD upgrade is successful.
cs2#

  11. Si va a actualizar a NX-OS versión 9,3(11), debe actualizar la imagen EPLD golden y reiniciar el conmutador una vez más. De lo contrario, vaya al paso 12.

    Consulte "Notas de la versión de actualización de EPLD, versión 9,3(11)" para obtener más información.

    Muestra el ejemplo 
    cs2# install epld bootflash:n9000-epld.9.3.11.img module 1 golden
Digital signature verification is successful
Compatibility check:
Module        Type         Upgradable     Impact      Reason
------  -----------------  -------------  ----------  -----------------
     1        SUP          Yes            Disruptive  Module Upgradable

Retrieving EPLD versions.... Please wait.
The above modules require upgrade.
The switch will be reloaded at the end of the upgrade
Do you want to continue (y/n) ?  [n] y

Proceeding to upgrade Modules.

 Starting Module 1 EPLD Upgrade

Module 1 : MI FPGA [Programming] : 100.00% (     64 of      64 sect)
Module 1 : IO FPGA [Programming] : 100.00% (     64 of      64 sect)
Module 1 EPLD upgrade is successful.
Module        Type          Upgrade-Result
------  ------------------  --------------
     1         SUP          Success

EPLDs upgraded.

Module 1 EPLD upgrade is successful.
cs2#

  12. Tras reiniciar el conmutador, inicie sesión para verificar que la nueva versión de EPLD se ha cargado correctamente.

    Muestra el ejemplo 
    cs2# show version module 1 epld

EPLD Device                     Version
---------------------------------------
MI   FPGA                        0x12
IO   FPGA                        0x12

  13. Compruebe el estado de los puertos del clúster en el clúster.

    1. Compruebe que los puertos del clúster estén en buen estado en todos los nodos del clúster:

      network port show -role cluster

      Muestra el ejemplo 
      cluster1::*> network port show -role cluster

Node: cluster1-01
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e0a       Cluster      Cluster          up   9000  auto/10000 healthy  false
e0b       Cluster      Cluster          up   9000  auto/10000 healthy  false

Node: cluster1-02
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e0a       Cluster      Cluster          up   9000  auto/10000 healthy  false
e0b       Cluster      Cluster          up   9000  auto/10000 healthy  false

Node: cluster1-03
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e0a       Cluster      Cluster          up   9000  auto/100000 healthy false
e0d       Cluster      Cluster          up   9000  auto/100000 healthy false

Node: cluster1-04
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e0a       Cluster      Cluster          up   9000  auto/100000 healthy false
e0d       Cluster      Cluster          up   9000  auto/100000 healthy false
8 entries were displayed.

    2. Compruebe el estado del switch del clúster.

      network device-discovery show -protocol cdp

    Muestra el ejemplo 
    cluster1::*> network device-discovery show -protocol cdp
Node/       Local  Discovered
Protocol    Port   Device (LLDP: ChassisID)  Interface         Platform
----------- ------ ------------------------- ----------------- ----------
cluster1-01/cdp
            e0a    cs1                       Ethernet1/7       N3K-C3232C
            e0d    cs2                       Ethernet1/7       N3K-C3232C
cluster01-2/cdp
            e0a    cs1                       Ethernet1/8       N3K-C3232C
            e0d    cs2                       Ethernet1/8       N3K-C3232C
cluster01-3/cdp
            e0a    cs1                       Ethernet1/1/1     N3K-C3232C
            e0b    cs2                       Ethernet1/1/1     N3K-C3232C
cluster1-04/cdp
            e0a    cs1                       Ethernet1/1/2     N3K-C3232C
            e0b    cs2                       Ethernet1/1/2     N3K-C3232C

cluster1::*> system cluster-switch show -is-monitoring-enabled-operational true
Switch                      Type               Address          Model
--------------------------- ------------------ ---------------- ----------
cs1                         cluster-network    10.233.205.90    N3K-C3232C
     Serial Number: FOCXXXXXXGD
      Is Monitored: true
            Reason: None
  Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                    9.3(5)
    Version Source: CDP

cs2                         cluster-network    10.233.205.91    N3K-C3232C
     Serial Number: FOCXXXXXXGS
      Is Monitored: true
            Reason: None
  Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                    9.3(5)
    Version Source: CDP

2 entries were displayed.

    Puede observar la siguiente salida en la consola del conmutador cs1 dependiendo de la versión RCF cargada previamente en el conmutador:

    2020 Nov 17 16:07:18 cs1 %$ VDC-1 %$ %STP-2-UNBLOCK_CONSIST_PORT: Unblocking port port-channel1 on VLAN0092. Port consistency restored.
2020 Nov 17 16:07:23 cs1 %$ VDC-1 %$ %STP-2-BLOCK_PVID_PEER: Blocking port-channel1 on VLAN0001. Inconsistent peer vlan.
2020 Nov 17 16:07:23 cs1 %$ VDC-1 %$ %STP-2-BLOCK_PVID_LOCAL: Blocking port-channel1 on VLAN0092. Inconsistent local vlan.

  14. Compruebe que el clúster esté en buen estado:

    cluster show

    Muestra el ejemplo 
    cluster1::*> cluster show
Node                 Health   Eligibility   Epsilon
-------------------- -------- ------------- -------
cluster1-01          true     true          false
cluster1-02          true     true          false
cluster1-03          true     true          true
cluster1-04          true     true          false
4 entries were displayed.
cluster1::*>

  15. Repita los pasos 6 a 14 en el interruptor CS1.

  16. Habilite la reversión automática en las LIF del clúster.

    network interface modify -vserver Cluster -lif * -auto-revert true

  17. Compruebe que las LIF del clúster han vuelto a su puerto de inicio:

    network interface show -role cluster

    Muestra el ejemplo 
    cluster1::*> network interface show -role cluster
            Logical            Status     Network            Current             Current Is
Vserver     Interface          Admin/Oper Address/Mask       Node                Port    Home
----------- ------------------ ---------- ------------------ ------------------- ------- ----
Cluster
            cluster1-01_clus1  up/up      169.254.3.4/23     cluster1-01         e0d     true
            cluster1-01_clus2  up/up      169.254.3.5/23     cluster1-01         e0d     true
            cluster1-02_clus1  up/up      169.254.3.8/23     cluster1-02         e0d     true
            cluster1-02_clus2  up/up      169.254.3.9/23     cluster1-02         e0d     true
            cluster1-03_clus1  up/up      169.254.1.3/23     cluster1-03         e0b     true
            cluster1-03_clus2  up/up      169.254.1.1/23     cluster1-03         e0b     true
            cluster1-04_clus1  up/up      169.254.1.6/23     cluster1-04         e0b     true
            cluster1-04_clus2  up/up      169.254.1.7/23     cluster1-04         e0b     true
8 entries were displayed.
cluster1::*>

    Si alguna LIF de clúster no ha regresado a sus puertos raíz, revertirla manualmente desde el nodo local:

    network interface revert -vserver Cluster -lif <lif_name>

El futuro

"Instale el archivo de configuración RCF".