ERROR

This message occurs when total number of async events are overflowed.

(None).

FC-VI adapter: Port %s async event overflowed. Resetting the adapter.

port (STRING): FCVI Interconnect NIC.

ERROR

This message occurs when the FC-VI adapter detects a connection error. The FC-VI driver will attempt to retry the connection.

If this message repeats frequently, there may be an issue with the FC fabric or the adapter. Contact NetApp technical support.

FC-VI adapter: Port %s detects connection error. FC-VI opcode = %s(0x%x), QP name = %s, QP index = %d, Remote node's system id = %llu. %s

port (STRING): Interconnect NIC.
opcode_str (STRING): FCVI opcode.
opcode (INTHEX): FCVI opcode.
qpname (STRING): QP name.
qpnum (INT): QP number.
systemID (LONGINT): Remote node's system ID.
info (STRING): Additional info.

ERROR

This message occurs when the CPR reset initiated by the FC-VI port got cancelled.

Reboot the filer. If issue still persists then replace the FCVI adapter.

FC-VI adapter: CPR reset initiated by port %s got cancelled. Offlining the port.

port (STRING): FCVI Interconnect adapter.

ERROR

This message occurs when the CPR reset initiated by the FC-VI port fails.

Reboot the filer. If issue still persists then replace the FCVI adapter.

FC-VI adapter: CPR reset initiated by port %s failed.

port (STRING): FCVI Interconnect adapter.

ERROR

This message occurs when the CPR reset is not supported by the adapter.

Reboot the filer. If issue still persists then replace the FCVI adapter.

FC-VI adapter: CPR reset is not supported by port %s.

port (STRING): FCVI Interconnect adapter.

ERROR

This message occurs when the FC-VI adapter firmware discards a received frame because of a receive frame error.

(None).

FC-VI adapter: Discarded a received frame because of a receive frame error. Port %s, QP name = %s, QP index = %d, exchange ID 0x%x, address offset 0x%x, remote node's system id = %llu. %s

port (STRING): FCVI Interconnect NIC.
qp_name (STRING): QP name.
qp_index (INT): QP number.
exchange_id (INTHEX): Exchange ID.
address (INTHEX): Address offset of the last good frame.
system_id (LONGINT): Remote node's system id.
info (STRING): Additional info.

ERROR

This message occurs when an FC-VI port's soft reset fails.

If CPR reset is not supported in the platform, then reboot the filer to recover from this issue. If issue persists then replace the FCVI adapter.

FC-VI adapter: Hard reset failed at port %s.

port (STRING): FCVI Interconnect adapter.

ERROR

This message occurs when FCVI driver receives invalid data from firmware.

(None).

FC-VI adapter: Port %s received invalid data. QP index = %d, completion status = %s(status code = %d), opcode = %s(%d), remote node's system id = %llu. %s

port (STRING): FCVI Interconnect NIC.
qpnum (INT): QP index.
status (STRING): Completion status.
status_code (INT): Completion status code.
opcode_str (STRING): FCVI opcode in string.
opcode (INT): FCVI opcode.
systemID (LONGINT): Remote node's system Id.
info (STRING): Additional info.

ERROR

This message occurs when FCVI driver receives a response with invalid exchange address.

(None).

FC-VI adapter: Port %s received invalid exchange address for %s. QP name = %s, QP index = %d, expected exchange address = 0x%x, received exchange address = 0x%x. %s

port (STRING): FCVI Interconnect NIC.
resp_type (STRING): Response type.
qpname (STRING): QP name.
qpnum (INT): QP number.
exp_oxid (INTHEX): Expected exchange address.
rcvd_oxid (INTHEX): Received exchange address.
info (STRING): Additional info.

ERROR

This message occurs when FCVI driver receives invalid QP index from firmware.

(None).

FC-VI adapter: Port %s received invalid QP. Received QP index = %d, completion status = %s(status code = %d), entry type = %s(entry code = %d). %s

port (STRING): FCVI Interconnect NIC.
qpnum (INT): QP index.
status (STRING): Completion status.
status_code (INT): Completion status code.
entry_type (STRING): Request/Response entry type.
entry_code (INT): Request/Response entry code.
info (STRING): Additional info.

ERROR

This message occurs when FCVI driver receives invalid response from firmware.

(None).

FC-VI adapter: Port %s received invalid response. %s. %s

port (STRING): FCVI Interconnect NIC.
error_type (STRING): Type of error.
info (STRING): Additional info.

ERROR

This message occurs when the FC-VI driver receives some IO error.

No corrective action is required. The driver internally resets the adapter if required. However, if you see this message frequently, there might be an issue with the FC fabric or the adapter. Contact NetApp technical support.

FC-VI adapter: FCVI driver on port %s received IO error. Status = %s(status code = 0x%x), FCVI opcode = %s(0x%x), QP name = %s, QP index = %d, Remote node's system id = %llu.

port (STRING): Interconnect NIC.
status_str (STRING): Completion status in string.
status (INTHEX): Completion status code.
opcode_str (STRING): FCVI opcode in string.
opcode (INTHEX): FCVI opcode.
qpName (STRING): QP name.
qpIndex (INT): QP number.
systemID (LONGINT): Remote node's system ID.

NOTICE

This message occurs when port login request times out.

(None).

FC-VI adapter: Remote port login timedout on port %s. Remote port id = 0x%x, Remote port handle = %d. %s

port (STRING): FCVI Interconnect NIC.
portid (INTHEX): Remote port identifier.
porthandle (INT): Remote port handle.
info (STRING): Additional info.

ERROR

This message occurs when the FCVI firmware rejects a link service.

(None).

FC-VI adapter: Link service = %s(code = %d), rejected on port %s. %s

ls (STRING): Link service name.
ls_code (INT): Link service code.
port (STRING): FCVI Interconnect NIC.
info (STRING): Additional info.

ERROR

This message occurs when a mailbox command is pending for a long time.

(None).

FC-VI adapter: Mailbox command '%s(code = 0x%x)' pending on port %s. %s

cmd (STRING): Mailbox command.
cmd_code (INTHEX): Mailbox command code.
port (STRING): FCVI Interconnect NIC.
info (STRING): Additional info.

ERROR

This message occurs when a mailbox command times out.

(None).

FC-VI adapter: Mailbox command '%s(code = 0x%x)' timedout on port %s. %s

cmd (STRING): Mailbox command.
cmd_code (INTHEX): Mailbox command code.
port (STRING): FCVI Interconnect NIC.
info (STRING): Additional info.

ERROR

This message occurs when the FCVI firmware identifies no more incoming IU buffers in the free pool.

(None).

FC-VI adapter: Port %s doesn't have free IU buffer. %s

port (STRING): FCVI Interconnect NIC.
info (STRING): Additional info.

ERROR

This message occurs when the FCVI firmware identifies no more receive buffers available for the incoming receive frames.

(None).

FC-VI adapter: Port %s doesn't have free receive buffer. QP name = %s, QP index = %d, Message ID = 0x%x. %s

port (STRING): FCVI Interconnect NIC.
qpname (STRING): QP name.
qpnum (INT): QP index.
msg_id (INTHEX): Message id of the incoming message.
info (STRING): Additional info.

ERROR

This message occurs when the FC-VI driver receives out of order completions.

No corrective action is required. The driver internally resets the adapter if required. However, if you see this message frequently, there might be an issue with the FC fabric or the adapter. Contact NetApp technical support.

FC-VI adapter: FCVI driver on port %s receives out of order completions. FCVI opcode = %s(0x%x), QP name = %s, QP index = %d, Remote node's system id = %llu.

port (STRING): Interconnect NIC.
opcode_str (STRING): FCVI opcode in string.
opcode (INTHEX): FCVI opcode.
qpName (STRING): QP name.
qpIndex (INT): QP number.
systemID (LONGINT): Remote node's system ID.

ERROR

This message occurs when the FC-VI adapter firmware encounters a PCI error because it cannot write a frame to host memory.

(None).

FC-VI adapter: PCI error while writing a frame to host memory. Port %s, QP name = %s, QP index = %d, exchange ID 0x%x, address offset 0x%x, remote node's system id = %llu. %s

port (STRING): FCVI Interconnect NIC.
qp_name (STRING): QP name.
qp_index (INT): QP number.
exchange_id (INTHEX): Exchange ID.
address (INTHEX): Address offset of the last good frame.
system_id (LONGINT): Remote node's system id.
info (STRING): Additional info.

ERROR

This message occurs when a FCVI port resets.

(None).

FC-VI adapter: Resetting the port %s. %s

port (STRING): FCVI Interconnect NIC.
reason (STRING): Reason for port reset.

ERROR

This message occurs when QP creation fails.

(None).

FC-VI adapter: Failed to create QP on port %s. Requested QP index = %d, completion status = %s(status code = %d). %s

port (STRING): FCVI Interconnect NIC.
qpnum (INT): QP index.
status (STRING): Completion status.
status_code (INT): Completion status code.
info (STRING): Additional info.

ERROR

This message occurs when the QP destroy request failed.

(None).

FC-VI adapter: QP destroy failed on port %s. QP index = %d. %s

port (STRING): FCVI Interconnect NIC.
qpnum (INT): QP index.
info (STRING): Additional info.

ERROR

This message occurs when the FC-VI driver receives a QP error from the Firmware. The FC-VI driver will attempt to retry the connection.

If this message repeats frequently, there may be an issue with the FC fabric or the adapter. Contact NetApp technical support.

FC-VI adapter: FCVI driver on port %s received QP Error. QP name = %s, QP index = 0x%x, VI state = %s(state code = 0x%x), sub-error = %s(error code = 0x%x). Remote node's system id = %llu. This error has occurred %d times. %s

port (STRING): Interconnect Adapter.
qpname (STRING): QP name.
qpnum (INTHEX): QP number.
state_str (STRING): QP state.
state (INTHEX): QP state code.
suberror (STRING): Sub-error.
code (INTHEX): Sub-error code.
system_id (LONGINT): Remote node's system ID.
errcnt (INT): Number of times QP async error was encountered.
info (STRING): Additional info.

ERROR

This message occurs when the FC-VI adapter receives invalid information unit buffer.

No corrective action is required. The driver internally resets the adapter if required. However, if you see this message frequently, there might be an issue with the FC fabric or the adapter. Contact NetApp technical support.

FC-VI adapter: Port %s received invalid IU buffer. Status = %s(status code = 0x%x), FCVI opcode = %s(0x%x), QP name = %s, QP index = %d, buffer handle = %d, Remote node's system id = %llu. %s

port (STRING): Interconnect NIC.
status_str (STRING): Completion status in string.
status (INTHEX): Completion status code.
opcode_str (STRING): FCVI opcode in string.
opcode (INTHEX): FCVI opcode.
qpname (STRING): QP name.
qpnum (INT): QP number.
bufhdl (INT): Buffer handle.
systemID (LONGINT): Remote node's system ID.
info (STRING): Additional info.

ERROR

This message occurs when the FCVI firmware detects an error in the received frame.

(None).

FC-VI adapter: Received bad frame on port %s. Mailbox-1 = %d, Mailbox-2 = %d. %s

port (STRING): FCVI Interconnect NIC.
mbox1 (INT): Content of mailbox-1.
mbox2 (INT): Content of mailbox-2.
info (STRING): Additional info.

NOTICE

This message occurs when FCVI driver receives disconnect request from partner.

(None).

FC-VI adapter: Disconnect request received on port %s. QP name = %s, QP index = %d, Remote node's system id = %llu. %s

port (STRING): FCVI Interconnect NIC.
qpname (STRING): QP name.
qpnum (INT): QP index.
system_id (LONGINT): Remote node's system id.
info (STRING): Additional info.

NOTICE

This message occurs when FCVI driver receives connection reject from partner.

(None).

FC-VI adapter: Connect request rejected on port %s. QP name = %s, QP index = %d, Remote node's system id = %llu. %s

port (STRING): FCVI Interconnect NIC.
qpname (STRING): QP name.
qpnum (INT): QP index.
system_id (LONGINT): Remote node's system id.
info (STRING): Additional info.

ERROR

This message occurs when the FC-VI adapter receives some error in received information unit.

No corrective action is required. The driver internally resets the adapter if required. However, if you see this message frequently, there might be an issue with the FC fabric or the adapter. Contact NetApp technical support.

FC-VI adapter: Port %s received IU error. Status = %s(status code = 0x%x), FCVI opcode = %s(0x%x), QP name = %s, QP index = %d, buffer handle = %d, Remote node's system id = %llu.

port (STRING): Interconnect NIC.
status_str (STRING): Completion status in string.
status (INTHEX): Completion status code.
opcode_str (STRING): FCVI opcode in string.
opcode (INTHEX): FCVI opcode.
qpname (STRING): QP name.
qpnum (INT): QP number.
bufhdl (INT): Buffer handle.
systemID (LONGINT): Remote node's system ID.

NOTICE

This message occurs when the FCVI driver saves a diagnostic dump in a file.

(None).

FC-VI adapter: Diagnostic dump for port %s saved to file %s.

port (STRING): FCVI Interconnect NIC.
filename (STRING): File to which the diagnostic dump was saved.

ERROR

This message occurs when the adapter firmware sends a response frame with the error bit set.

(None).

FC-VI adapter: Firmware sent a response with the error bit set. Port %s, QP name = %s, QP index = %d, exchange ID 0x%x, address offset 0x%x, remote node's system id = %llu. %s

port (STRING): FCVI Interconnect NIC.
qpname (STRING): QP name.
qp_index (INT): QP number.
exchange_id (INTHEX): Exchange ID.
address (INTHEX): Address offset of the last good frame.
system_id (LONGINT): Remote node's system id.
info (STRING): Additional info.

ERROR

This message occurs when FCVI RISC is paused.

(None).

FC-VI adapter: Port %s detected a RISC pause error. %s

port (STRING): FCVI Interconnect NIC.
info (STRING): Additional info.

NOTICE

This message occurs when FCVI driver lost link to partner port.

(None).

FC-VI adapter: Link to partner node over port %s is down. Partner port id = 0x%x, partner node's system id = %llu. %s

port (STRING): FCVI Interconnect NIC.
port_id (INTHEX): Partner port id.
system_id (LONGINT): Partner node's system id.
info (STRING): Additional info.

NOTICE

This message occurs when FCVI driver gets link to partner port.

(None).

FC-VI adapter: Link to partner node over port %s is up. Partner port id = 0x%x, partner node's system id = %llu. %s

port (STRING): FCVI Interconnect NIC.
port_id (INTHEX): Partner port id.
system_id (LONGINT): Partner node's system id.
info (STRING): Additional info.

ERROR

This message occurs when the FC-VI adapter fails to send an information unit.

No corrective action is required. The driver internally retries. However, if you see this message frequently, there might be an issue with the FC fabric or the adapter. Contact NetApp technical support.

FC-VI adapter: Port %s sendIU status = %s(status code = 0x%x), FCVI opcode = %s(0x%x), QP name = %s, QP index = %d, Remote node's system id = %llu. %s

port (STRING): Interconnect NIC.
status_str (STRING): Completion status in string.
status (INTHEX): Completion status code in hex.
opcode_str (STRING): FCVI opcode in string.
opcode (INTHEX): FCVI opcode in hex.
qpName (STRING): QP name.
qpIndex (INT): QP number.
systemID (LONGINT): Remote node's system id.
info (STRING): Additional info.

NOTICE

This message occurs when FCVI driver sends disconnect request to remote partner.

(None).

FC-VI adapter: Disconnect request sent on port %s. QP name = %s, QP index = %d, Remote node's system id = %llu. %s

port (STRING): FCVI Interconnect NIC.
qpname (STRING): QP name.
qpnum (INT): QP index.
system_id (LONGINT): Remote node's system id.
info (STRING): Additional info.

ERROR

This message occurs when an FC-VI port's soft reset fails.

None.

FC-VI adapter: Soft reset failed at port %s.

port (STRING): FCVI Interconnect adapter.

ERROR

This message occurs when FCVI driver receives system error from FCVI firmware.

No corrective action is required. The driver internally resets the adapter. However, if you see this message frequently, there might be an issue with the adapter/firmware. Contact NetApp technical support.

FC-VI adapter: System Error on port %s. %s

port (STRING): FCVI Interconnect NIC.
info (STRING): Additional info.

ERROR

This message occurs when the adapter firmware cannot send a request.

(None).

FC-VI adapter: Firmware could not send a request. Port %s, QP name = %s, QP index = %d, exchange ID 0x%x, address offset 0x%x, remote node's system id = %llu. %s

port (STRING): FCVI Interconnect NIC.
qp_name (STRING): QP name.
qp_index (INT): QP number.
exchange_id (INTHEX): Exchange ID.
address (INTHEX): Address offset of the last good frame.
system_id (LONGINT): Remote node's system id.
info (STRING): Additional info.

ERROR

This message occurs when the FCVI firmware detects a transfer error.

(None).

FC-VI adapter: %s transfer error on port %s. Affected queue number = %d. %s

trans_type (STRING): Transfer type.
port (STRING): FCVI Interconnect NIC.
queue_num (INT): Queue number.
info (STRING): Additional info.