# sanlun lun show all

controller(7mode/E-Series)/            device     host               lun
vserver(cDOT/FlashRay)   lun-pathname  filename   adapter  protocol  size    Product
------------------------------------------------------------------------------------
data_vserver          /vol/vol1/lun1   /dev/sdb   host16   FCP       120.0g  cDOT
data_vserver          /vol/vol1/lun1   /dev/sdc   host15   FCP       120.0g  cDOT
data_vserver          /vol/vol2/lun2   /dev/sdd   host16   FCP       120.0g  cDOT
data_vserver          /vol/vol2/lun2   /dev/sde   host15   FCP       120.0g  cDOT

chkconfig multipathd on
/etc/init.d/multipathd start

blacklist {
        wwid <DevId>
        devnode "^(ram|raw|loop|fd|md|dm-|sr|scd|st)[0-9]*"
        devnode "^hd[a-z]"
        devnode "^cciss.*"
}

+
`sda` is the local SCSI disk that you want to add to the blacklist.

. Add the `WWID` to the blacklist stanza in `/etc/multipath.conf`:
[source,cli]
+

Always check your `/etc/multipath.conf` file, especially in the defaults section, for legacy settings that might be overriding default settings.

The following table demonstrates the critical `multipathd` parameters for ONTAP LUNs and the required values. If a host is connected to LUNs from other vendors and any of these parameters are overridden, they must be corrected by later stanzas in the `multipath.conf` file that apply specifically to ONTAP LUNs. Without this correction, the ONTAP LUNs might not work as expected. You should only override these defaults in consultation with NetApp, the OS vendor, or both, and only when the impact is fully understood.

//ONTAPDOC-2578 9-Dec-2024
//ONTAPDOC-2561 25-Nov-202


[cols=2*,options="header"]
|===
| Parameter
| Setting
| detect_prio | yes
| dev_loss_tmo | "infinity"
| failback | immediate
| fast_io_fail_tmo | 5
| features | "3 queue_if_no_path pg_init_retries 50"
| flush_on_last_del | "yes"
| hardware_handler | "0"
| no_path_retry | queue
| path_checker | "tur"
| path_grouping_policy | "group_by_prio"
| path_selector | "service-time 0"
| polling_interval | 5
| prio | "ontap"
| product | LUN.*
| retain_attached_hw_handler | yes
| rr_weight | "uniform"
| user_friendly_names | no
| vendor | NETAPP
|===

.Example

The following example shows how to correct an overridden default. In this case, the `multipath.conf` file defines values for `path_checker` and `no_path_retry` that are not compatible with ONTAP LUNs. If they cannot be removed because of other SAN arrays still attached to the host, these parameters can be corrected specifically for ONTAP LUNs with a device stanza.

=== Configure KVM settings

You can use the recommended settings to configure Kernel-based Virtual Machine (KVM) as well. There are no changes required to configure KVM because the LUN is mapped to the hypervisor.

//ONTAPDOC-2561 5-Dec-2024

== Known issues

The CentOS 7.9 with ONTAP release has the following known issues:

[cols=3*,options="header"]
|===
| NetApp Bug ID
| Title
| Description
| 1440718 | If you unmap or map a LUN without performing a SCSI rescan, it might lead to data corruption on the host. | When you set the 'disable_changed_wwids' multipath configuration parameter to YES, it disables access to the path device in the event of a WWID change. Multipath will disable access to the path device until the WWID of the path is restored to the WWID of the multipath device. To learn more, see  link:https://kb.netapp.com/Advice_and_Troubleshooting/Flash_Storage/AFF_Series/The_filesystem_corruption_on_iSCSI_LUN_on_the_Oracle_Linux_7[NetApp Knowledge Base: The filesystem corruption on iSCSI LUN on the Oracle Linux 7^].
|===


// BURT 1447018, 28-02-22