Skip to main content

Confirm that the new controllers are set up correctly

Contributors netapp-aoife netapp-pcarriga netapp-aherbin
PDFs

To confirm correct setup, you must enable the HA pair. You must also verify that node3 and node4 can access each other's storage and that neither owns data LIFs belonging to other nodes on the cluster. In addition, you must confirm that node3 owns node1's aggregates and that node4 owns node2's aggregates, and that the volumes for both nodes are online.

Steps

  1. After the post-checks of node2, the storage failover and cluster HA pair for the node2 cluster are enabled. When the operation is done, both nodes show as completed and the system performs some cleanup operations.

  2. Verify that storage failover is enabled:

    storage failover show

    The following example shows the output of the command when storage failover is enabled:

    cluster::> storage failover show
                  Takeover
Node     Partner  Possible   State Description
-------- -----    -------    ------------------
node3    node4    true       Connected to node4
node4    node3    true       Connected to node3

  3. Verify that node3 and node4 belong to the same cluster by using the following command and examining the output:

    cluster show

  4. Verify that node3 and node4 can access each other's storage by using the following command and examining the output:

    storage failover show -fields local-missing-disks, partner-missing-disks

  5. Verify that neither node3 nor node4 owns data LIFs home-owned by other nodes in the cluster by using the following command and examining the output:

    network interface show

    If neither node3 or node4 owns data LIFs home-owned by other nodes in the cluster, revert the data LIFs to their home owner:

    network interface revert

  6. Verify that node3 owns the aggregates from node1 and that node4 owns the aggregates from node2:

    storage aggregate show -owner-name node3

    storage aggregate show -owner-name node4

  7. Determine whether any volumes are offline:

    volume show -node node3 -state offline

    volume show -node node4 -state offline

  8. If any volumes are offline, compare them with the list of offline volumes that you captured in the section Prepare the nodes for upgrade, and bring online any of the offline volumes, as required, by using the following command, once for each volume:

    volume online -vserver vserver_name -volume volume_name

  9. Install new licenses for the new nodes by using the following command for each node:

    system license add -license-code license_code,license_code,license_code…

    The license-code parameter accepts a list of 28 upper-case alphabetic character keys. You can add one license at a time, or you can add multiple licenses at once, separating each license key by a comma.

  10. Remove all of the old licenses from the original nodes by using one of the following commands:

    system license clean-up -unused -expired

    system license delete -serial-number node_serial_number -package licensable_package

    • Delete all expired licenses:

      system license clean-up -expired

    • Delete all unused licenses:

      system license clean-up -unused

    • Delete a specific license from a cluster by using the following commands on the nodes:

      system license delete -serial-number node1_serial_number -package *

      system license delete -serial-number node2_serial_number -package *

    The following output is displayed:

    Warning: The following licenses will be removed:
<list of each installed package>
Do you want to continue? {y|n}: y

    Enter y to remove all of the packages.

  11. Verify that the licenses are correctly installed by using the following command and examining the output:

    system license show

    You can compare the output with the output that you captured in the section Prepare the nodes for upgrade.

  12. If self-encrypting drives are being used in the configuration and you have set the kmip.init.maxwait variable to off (for example, in Install and boot node4, Step 27), you must unset the variable:

    set diag; systemshell -node node_name -command sudo kenv -u -p kmip.init.maxwait

  1. Configure the SPs by using the following command on both nodes:

    system service-processor network modify -node node_name

    Refer to References to link to the System Administration Reference for information about the SPs and the ONTAP 9.8 Commands: Manual Page Reference for detailed information about the system service-processor network modify command.

  2. If you want to set up a switchless cluster on the new nodes, refer to References to link to the NetApp Support Site and follow the instructions in Transitioning to a two-node switchless cluster.

After you finish

If Storage Encryption is enabled on node3 and node4, complete the section Set up Storage Encryption on the new controller module. Otherwise, complete the section Decommission the old system.