Instalar el software NX-OS y los archivos de configuración de referencia (RCF)
Instale el software NX-OS y RCF en un switch de clúster Cisco Nexus 9336C- FX2
Debe instalarse el software Cisco NX-OS y el archivo de configuración de referencia (RCF) en los switches de clúster Cisco Nexus 9336C-FX2.
Deben existir las siguientes condiciones antes de instalar el software NX-OS y RCF en el switch del clúster:
-
El clúster debe estar funcionando completamente (no debe haber errores en los registros ni problemas similares).
-
Debe haber comprobado o establecido la configuración de inicio deseada en el RCF para reflejar las imágenes de arranque deseadas si sólo está instalando NX-OS y manteniendo su versión actual de RCF.
-
Si necesita cambiar la configuración de arranque para reflejar las imágenes de arranque actuales, debe hacerlo antes de volver a aplicar el RCF para que se cree una instancia de la versión correcta en futuros reinicios.
-
Debe tener una conexión de consola al conmutador, necesaria para instalar el RCF.
-
Debe haber consultado la tabla de compatibilidad de switches de la página del conmutador Ethernet de Cisco para las versiones ONTAP, NX-OS y RCF compatibles. Consulte "Switches Ethernet de Cisco" si quiere más información.
-
Puede haber dependencias de comandos entre la sintaxis de comandos en el RCF y la que se encuentra en las versiones de NX-OS.
-
Debe haber hecho referencia a las guías de software y actualizaciones adecuadas disponibles en el sitio web de Cisco para obtener documentación completa sobre los procedimientos de actualización y degradación de switches de Cisco en los switches de la serie Cisco Nexus 9000. Consulte "Switches Cisco Nexus serie 9000" si quiere más información.
-
Debe tener el RCF actual.
Configuración inicial
Los ejemplos de este procedimiento utilizan dos nodos. Estos nodos utilizan dos puertos de interconexión de clúster de 100 GbE e3a y e3b, como se indica en la controladora A400. Consulte "Hardware Universe" para verificar los puertos de clúster correctos en sus plataformas.
Los resultados del comando pueden variar en función de las diferentes versiones de ONTAP. |
Los ejemplos de este procedimiento utilizan la nomenclatura de conmutador y nodo siguiente:
-
Los nombres de los dos switches Cisco son cs1 y cs2.
-
Los nombres de nodo son cluster1-01 y cluster1-02.
-
Los nombres de las LIF del clúster son cluster1-01_clus1 y cluster1-01_clus2 para cluster1-01 y cluster1-02_clus1 y cluster1-02_clus2 para cluster1-02.
-
El símbolo del sistema cluster1:*> indica el nombre del clúster.
Para ello, es necesario utilizar tanto comandos de la ONTAP como comandos de la serie Cisco Nexus 9000; los comandos de la ONTAP se usan a menos que se indique lo contrario. |
-
Si AutoSupport está habilitado en este clúster, elimine la creación automática de casos invocando un mensaje de AutoSupport:
system node autosupport invoke -node * -type all -message MAINT=x h
Donde x es la duración de la ventana de mantenimiento en horas.
-
cambie el nivel de privilegio a avanzado, introduciendo y cuando se le solicite continuar:
set -privilege advanced
Aparece el mensaje avanzado (*>).
-
muestra cuántas interfaces de interconexión de clúster están configuradas en cada nodo para cada switch de interconexión de clúster:
network device-discovery show -protocol cdp
cluster1:: network device-discovery show -protocol cdp Node/ Local Discovered Protocol Port Device (LLDP: ChassisID) Interface Platform ----------- ------ ------------------------- ----------------- -------- cluster1-02/cdp e3a cs1 Eth1/2 N9K-C9336C e3b cs2 Eth1/2 N9K-C9336C cluster1-01/cdp e3a cs1 Eth1/1 N9K-C9336C e3b cs2 Eth1/1 N9K-C9336C 4 entries were displayed.
cluster1::*> network port show -ipspace Cluster Node: cluster1-02 Speed(Mbps) Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status --------- ------------ ---------------- ---- ---- ------------ ------ e3a Cluster Cluster up 9000 auto/100000 healthy e3b Cluster Cluster up 9000 auto/100000 healthy Node: cluster1-01 Speed(Mbps) Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status --------- ------------ ---------------- ---- ---- ------------ ------ e3a Cluster Cluster up 9000 auto/100000 healthy e3b Cluster Cluster up 9000 auto/100000 healthy 4 entries were displayed.
-
Mostrar información acerca de las LIF:
network interface show - vserver Cluster
cluster1::*> network interface show -vserver Cluster Logical Status Network Current Current Is Vserver Interface Admin/Oper Address/Mask Node Port Home ------- ------------------ ---------- ------------------ ----------- ------ ---- Cluster cluster1-01_clus1 up/up 169.254.209.69/16 cluster1-01 e3a true cluster1-01_clus2 up/up 169.254.49.125/16 cluster1-01 e3b true cluster1-02_clus1 up/up 169.254.47.194/16 cluster1-02 e3a true cluster1-02_clus2 up/up 169.254.19.183/16 cluster1-02 e3b true 4 entries were displayed.
cluster1::*> cluster ping-cluster -node cluster1-02 Host is cluster1-02 Getting addresses from network interface table... Cluster cluster1-01_clus1 169.254.209.69 cluster1-01 e3a Cluster cluster1-01_clus2 169.254.49.125 cluster1-01 e3b Cluster cluster1-02_clus1 169.254.47.194 cluster1-02 e3a Cluster cluster1-02_clus2 169.254.19.183 cluster1-02 e3b Local = 169.254.47.194 169.254.19.183 Remote = 169.254.209.69 169.254.49.125 Cluster Vserver Id = 4294967293 Ping status: Basic connectivity succeeds on 4 path(s) Basic connectivity fails on 0 path(s) Detected 9000 byte MTU on 4 path(s): Local 169.254.19.183 to Remote 169.254.209.69 Local 169.254.19.183 to Remote 169.254.49.125 Local 169.254.47.194 to Remote 169.254.209.69 Local 169.254.47.194 to Remote 169.254.49.125 Larger than PMTU communication succeeds on 4 path(s) RPC status: 2 paths up, 0 paths down (tcp check) 2 paths up, 0 paths down (udp check)
cluster1::*> network interface show -vserver Cluster -fields auto-revert Logical Vserver Interface Auto-revert --------- ––––––-------------- ------------ Cluster cluster1-01_clus1 true cluster1-01_clus2 true cluster1-02_clus1 true cluster1-02_clus2 true 4 entries were displayed.
cluster1::*> system switch ethernet log setup password Enter the switch name: <return> The switch name entered is not recognized. Choose from the following list: cs1 cs2 cluster1::*> system switch ethernet log setup-password Enter the switch name: cs1 RSA key fingerprint is e5:8b:c6:dc:e2:18:18:09:36:63:d9:63:dd:03:d9:cc Do you want to continue? {y|n}::[n] y Enter the password: <enter switch password> Enter the password again: <enter switch password> cluster1::*> system switch ethernet log setup-password Enter the switch name: cs2 RSA key fingerprint is 57:49:86:a1:b9:80:6a:61:9a:86:8e:3c:e3:b7:1f:b1 Do you want to continue? {y|n}:: [n] y Enter the password: <enter switch password> Enter the password again: <enter switch password> cluster1::*> system switch ethernet log enable-collection Do you want to enable cluster log collection for all nodes in the cluster? {y|n}: [n] y Enabling cluster switch log collection. cluster1::*>
Si alguno de estos comandos devuelve un error, póngase en contacto con el soporte de NetApp. |
Instale el software NX-OS en un switch de clúster Cisco Nexus 9336C- FX2
Puede utilizar este procedimiento para instalar el software NX-OS en el switch de clúster Cisco Nexus 9336C-FX2.
cs2# ping 172.19.2.1 Pinging 172.19.2.1 with 0 bytes of data: Reply From 172.19.2.1: icmp_seq = 0. time= 5910 usec.
cs2# copy sftp: bootflash: vrf management Enter source filename: /code/nxos.9.3.5.bin Enter hostname for the sftp server: 172.19.2.1 Enter username: user1 Outbound-ReKey for 172.19.2.1:22 Inbound-ReKey for 172.19.2.1:22 user1@172.19.2.1's password: sftp> progress Progress meter enabled sftp> get /code/nxos.9.3.5.bin /bootflash/nxos.9.3.5.bin /code/nxos.9.3.5.bin 100% 1261MB 9.3MB/s 02:15 sftp> exit Copy complete, now saving to disk (please wait)... Copy complete. cs2# copy sftp: bootflash: vrf management Enter source filename: /code/n9000-epld.9.3.5.img Enter hostname for the sftp server: 172.19.2.1 Enter username: user1 Outbound-ReKey for 172.19.2.1:22 Inbound-ReKey for 172.19.2.1:22 user1@172.19.2.1's password: sftp> progress Progress meter enabled sftp> get /code/n9000-epld.9.3.5.img /bootflash/n9000-epld.9.3.5.img /code/n9000-epld.9.3.5.img 100% 161MB 9.5MB/s 00:16 sftp> exit Copy complete, now saving to disk (please wait)... Copy complete.
cs2# show version Cisco Nexus Operating System (NX-OS) Software TAC support: http://www.cisco.com/tac Copyright (C) 2002-2020, Cisco and/or its affiliates. All rights reserved. The copyrights to certain works contained in this software are owned by other third parties and used and distributed under their own licenses, such as open source. This software is provided "as is," and unless otherwise stated, there is no warranty, express or implied, including but not limited to warranties of merchantability and fitness for a particular purpose. Certain components of this software are licensed under the GNU General Public License (GPL) version 2.0 or GNU General Public License (GPL) version 3.0 or the GNU Lesser General Public License (LGPL) Version 2.1 or Lesser General Public License (LGPL) Version 2.0. A copy of each such license is available at http://www.opensource.org/licenses/gpl-2.0.php and http://opensource.org/licenses/gpl-3.0.html and http://www.opensource.org/licenses/lgpl-2.1.php and http://www.gnu.org/licenses/old-licenses/library.txt. Software BIOS: version 08.38 NXOS: version 9.3(4) BIOS compile time: 05/29/2020 NXOS image file is: bootflash:///nxos.9.3.4.bin NXOS compile time: 4/28/2020 21:00:00 [04/29/2020 02:28:31] Hardware cisco Nexus9000 C9336C-FX2 Chassis Intel(R) Xeon(R) CPU E5-2403 v2 @ 1.80GHz with 8154432 kB of memory. Processor Board ID FOC20291J6K Device name: cs2 bootflash: 53298520 kB Kernel uptime is 0 day(s), 0 hour(s), 3 minute(s), 42 second(s) Last reset at 157524 usecs after Mon Nov 2 18:32:06 2020 Reason: Reset Requested by CLI command reload System version: 9.3(4) Service: plugin Core Plugin, Ethernet Plugin Active Package(s): cs2#
La instalación del archivo de imagen hace que se cargue cada vez que se reinicia el conmutador. |
cs2# install all nxos bootflash:nxos.9.3.5.bin Installer will perform compatibility check first. Please wait. Installer is forced disruptive Verifying image bootflash:/nxos.9.3.5.bin for boot variable "nxos". [####################] 100% -- SUCCESS Verifying image type. [####################] 100% -- SUCCESS Preparing "nxos" version info using image bootflash:/nxos.9.3.5.bin. [####################] 100% -- SUCCESS Preparing "bios" version info using image bootflash:/nxos.9.3.5.bin. [####################] 100% -- SUCCESS Performing module support checks. [####################] 100% -- SUCCESS Notifying services about system upgrade. [####################] 100% -- SUCCESS Compatibility check is done: Module bootable Impact Install-type Reason ------ -------- --------------- ------------ ------ 1 yes disruptive reset default upgrade is not hitless Images will be upgraded according to following table: Module Image Running-Version(pri:alt New-Version Upg- Required ------- --------- -------------------------------------- ------------------- ------------ 1 nxos 9.3(4) 9.3(5) yes 1 bios v08.37(01/28/2020):v08.23(09/23/2015) v08.38(05/29/2020) yes Switch will be reloaded for disruptive upgrade. Do you want to continue with the installation (y/n)? [n] y Install is in progress, please wait. Performing runtime checks. [####################] 100% -- SUCCESS Setting boot variables. [####################] 100% -- SUCCESS Performing configuration copy. [####################] 100% -- SUCCESS Module 1: Refreshing compact flash and upgrading bios/loader/bootrom. Warning: please do not remove or power off the module at this time. [####################] 100% -- SUCCESS Finishing the upgrade, switch will reboot in 10 seconds.
cs2# show version Cisco Nexus Operating System (NX-OS) Software TAC support: http://www.cisco.com/tac Copyright (C) 2002-2020, Cisco and/or its affiliates. All rights reserved. The copyrights to certain works contained in this software are owned by other third parties and used and distributed under their own licenses, such as open source. This software is provided "as is," and unless otherwise stated, there is no warranty, express or implied, including but not limited to warranties of merchantability and fitness for a particular purpose. Certain components of this software are licensed under the GNU General Public License (GPL) version 2.0 or GNU General Public License (GPL) version 3.0 or the GNU Lesser General Public License (LGPL) Version 2.1 or Lesser General Public License (LGPL) Version 2.0. A copy of each such license is available at http://www.opensource.org/licenses/gpl-2.0.php and http://opensource.org/licenses/gpl-3.0.html and http://www.opensource.org/licenses/lgpl-2.1.php and http://www.gnu.org/licenses/old-licenses/library.txt. Software BIOS: version 05.33 NXOS: version 9.3(5) BIOS compile time: 09/08/2018 NXOS image file is: bootflash:///nxos.9.3.5.bin NXOS compile time: 11/4/2018 21:00:00 [11/05/2018 06:11:06] Hardware cisco Nexus9000 C9336C-FX2 Chassis Intel(R) Xeon(R) CPU E5-2403 v2 @ 1.80GHz with 8154432 kB of memory. Processor Board ID FOC20291J6K Device name: cs2 bootflash: 53298520 kB Kernel uptime is 0 day(s), 0 hour(s), 3 minute(s), 42 second(s) Last reset at 277524 usecs after Mon Nov 2 22:45:12 2020 Reason: Reset due to upgrade System version: 9.3(4) Service: plugin Core Plugin, Ethernet Plugin Active Package(s):
cs2# show version module 1 epld EPLD Device Version ---- -------------------------- ------- MI FPGA 0x7 IO FPGA 0x17 MI FPGA2 0x2 GEM FPGA 0x2 GEM FPGA 0x2 GEM FPGA 0x2 GEM FPGA 0x2 cs2# install epld bootflash:n9000-epld.9.3.5.img module 1 Compatibility check: Module Type Upgradable Impact Reason ------ -------------- ------------ ----------- ------- 1 SUP Yes disruptive Module Upgradable Retrieving EPLD versions... Please wait. Images will be upgraded according to following table: Module Type EPLD Running-Version New-Version Upg-Required ------- ------ ----------------- ----------------- ------------ ------------ 1 SUP MI FPGA 0x07 0x07 No 1 SUP IO FPGA 0x17 0x19 Yes 1 SUP MI FPGA2 0x02 0x02 No The above modules require upgrade. The switch will be reloaded at the end of the upgrade Do you want to continue (y/n) ? [n] y Proceeding to upgrade Modules. Starting Module 1 EPLD Upgrade Module 1 : IO FPGA [Programming] : 100.00% ( 64 of 64 sectors) Module 1 EPLD upgrade is successful. Module Type Upgrade-Result -------- ----- -------------- 1 SUP Success EPLDs upgraded. Module 1 EPLD upgrade is successful.
cs2# show version module 1 epld EPLD Device Version ---- -------------------------- -------- MI FPGA 0x7 IO FPGA 0x19 MI FPGA2 0x2 GEM FPGA 0x2 GEM FPGA 0x2 GEM FPGA 0x2 GEM FPGA 0x2
Instale el RCF en un switch de clúster Cisco Nexus 9336C-FX2
Puede instalar el RCF después de configurar por primera vez el switch de clúster Nexus 9336C-FX2. También puede usar este procedimiento para actualizar la versión de RCF en el switch de clúster.
Los ejemplos de este procedimiento utilizan la nomenclatura de conmutador y nodo siguiente:
-
Los nombres de los dos switches Cisco son
cs1
y..cs2
. -
Los nombres de nodo son
cluster1-01
,cluster1-02
,cluster1-03
, y.cluster1-04
. -
Los nombres de LIF del clúster son
cluster1-01_clus1
,cluster1-01_clus2
,cluster1-02_clus1
,cluster1-02_clus2
,cluster1-03_clus1
,cluster1-03_clus2
,cluster1-04_clus1
, y.cluster1-04_clus2
. -
El símbolo del sistema cluster1:*> indica el nombre del clúster.
Para ello, es necesario utilizar tanto comandos de la ONTAP como comandos de la serie Cisco Nexus 9000; los comandos de la ONTAP se usan a menos que se indique lo contrario. |
cluster1::*> network device-discovery show Node/ Local Discovered Protocol Port Device (LLDP: ChassisID) Interface Platform ----------- ------ ------------------------- ---------------- -------- cluster1-01/cdp e3a cs1 Ethernet1/7 N9K-C9336C e0d cs2 Ethernet1/7 N9K-C9336C cluster1-02/cdp e3a cs1 Ethernet1/8 N9K-C9336C e0d cs2 Ethernet1/8 N9K-C9336C cluster1-03/cdp e3a cs1 Ethernet1/1/1 N9K-C9336C e3b cs2 Ethernet1/1/1 N9K-C9336C cluster1-04/cdp e3a cs1 Ethernet1/1/2 N9K-C9336C e3b cs2 Ethernet1/1/2 N9K-C9336C cluster1::*>
cluster1::*> network port show -role cluster Node: cluster1-01 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ----------- -------- ------ e3a Cluster Cluster up 9000 auto/100000 healthy false e0d Cluster Cluster up 9000 auto/100000 healthy false Node: cluster1-02 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ----------- -------- ------ e3a Cluster Cluster up 9000 auto/100000 healthy false e0d Cluster Cluster up 9000 auto/100000 healthy false 8 entries were displayed. Node: cluster1-03 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ------------ -------- ------ e3a Cluster Cluster up 9000 auto/100000 healthy false e3b Cluster Cluster up 9000 auto/100000 healthy false Node: cluster1-04 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ------------ -------- ------ e0a Cluster Cluster up 9000 auto/100000 healthy false e0b Cluster Cluster up 9000 auto/100000 healthy false cluster1::*>
cluster1::*> network interface show -role cluster Logical Status Network Current Current Is Vserver Interface Admin/Oper Address/Mask Node Port Home ------- ------------------ ---------- --------------- ------------ ------- ---- Cluster cluster1-01_clus1 up/up 169.254.3.4/23 cluster1-01 e3a true cluster1-01_clus2 up/up 169.254.3.5/23 cluster1-01 e0d true cluster1-02_clus1 up/up 169.254.3.8/23 cluster1-02 e3a true cluster1-02_clus2 up/up 169.254.3.9/23 cluster1-02 e0d true cluster1-03_clus1 up/up 169.254.1.3/23 cluster1-03 e3a true cluster1-03_clus2 up/up 169.254.1.1/23 cluster1-03 e3b true cluster1-04_clus1 up/up 169.254.1.6/23 cluster1-04 e3a true cluster1-04_clus2 up/up 169.254.1.7/23 cluster1-04 e3b true 8 entries were displayed. cluster1::*>
cluster1::*> system cluster-switch show -is-monitoring-enabled-operational true Switch Type Address Model --------------------------- ------------------ ---------------- ----- cs1 cluster-network 10.233.205.90 N9K-C9336C Serial Number: FOCXXXXXXGD Is Monitored: true Reason: None Software Version: Cisco Nexus Operating System (NX-OS) Software, Version 9.3(5) Version Source: CDP cs2 cluster-network 10.233.205.91 N9K-C9336C Serial Number: FOCXXXXXXGS Is Monitored: true Reason: None Software Version: Cisco Nexus Operating System (NX-OS) Software, Version 9.3(5) Version Source: CDP cluster1::*>
cluster1::*> network interface modify -vserver Cluster -lif * -auto-revert false
cs2(config)# interface eth1/1/1-2,eth1/7-8 cs2(config-if-range)# shutdown
cluster1::*> network interface show -role cluster Logical Status Network Current Current Is Vserver Interface Admin/Oper Address/Mask Node Port Home ------- ----------------- --------- ---------------- ------------- ------- ---- Cluster cluster1-01_clus1 up/up 169.254.3.4/23 cluster1-01 e3a true cluster1-01_clus2 up/up 169.254.3.5/23 cluster1-01 e3a false cluster1-02_clus1 up/up 169.254.3.8/23 cluster1-02 e3a true cluster1-02_clus2 up/up 169.254.3.9/23 cluster1-02 e3a false cluster1-03_clus1 up/up 169.254.1.3/23 cluster1-03 e3a true cluster1-03_clus2 up/up 169.254.1.1/23 cluster1-03 e3a false cluster1-04_clus1 up/up 169.254.1.6/23 cluster1-04 e3a true cluster1-04_clus2 up/up 169.254.1.7/23 cluster1-04 e3a false 8 entries were displayed. cluster1::*>
cluster1::*> cluster show Node Health Eligibility Epsilon -------------------- ------- ------------ ------- cluster1-01 true true false cluster1-02 true true false cluster1-03 true true true cluster1-04 true true false 4 entries were displayed. cluster1::*>
cs2# write erase Warning: This command will erase the startup-configuration. Do you wish to proceed anyway? (y/n) [n] y cs2# reload This command will reboot the system. (y/n)? [n] y cs2#
-
Realice una configuración básica del interruptor.
-
copie el RCF al bootflash del conmutador cs2 utilizando uno de los siguientes protocolos de transferencia: FTP, TFTP, SFTP o SCP. Para obtener más información acerca de los comandos de Cisco, consulte la guía correspondiente en "Guías de referencia de comandos Cisco Nexus serie 9000 NX-OS".
En este ejemplo se muestra TFTP que se utiliza para copiar un RCF al bootflash del conmutador cs2.
cs2# copy tftp: bootflash: vrf management Enter source filename: Nexus_9336C_RCF_v1.6-Cluster-HA-Breakout.txt Enter hostname for the tftp server: 172.22.201.50 Trying to connect to tftp server...Connection to Server Established. TFTP get operation was successful Copy complete, now saving to disk (please wait)...
-
aplique el RCF descargado anteriormente al flash de inicio. Para obtener más información acerca de los comandos de Cisco, consulte la guía correspondiente en "Guías de referencia de comandos Cisco Nexus serie 9000 NX-OS".
En este ejemplo se muestra el archivo RCF
Nexus_9336C_RCF_v1.6-Cluster-HA-Breakout.txt
se está instalando en el conmutador cs2.
cs2# copy Nexus_9336C_RCF_v1.6-Cluster-HA-Breakout.txt running-config echo-commands
cs2# show banner motd *************************************************************************** * NetApp Reference Configuration File (RCF) * * Switch : Nexus N9K-C9336C-FX2 * Filename : Nexus_9336C_RCF_v1.6-Cluster-HA-Breakout.txt * Date : 10-23-2020 * Version : v1.6 * * Port Usage: * Ports 1- 3: Breakout mode (4x10G) Intra-Cluster Ports, int e1/1/1-4, * e1/2/1-4, e1/3/1-4 * Ports 4- 6: Breakout mode (4x25G) Intra-Cluster/HA Ports, int e1/4/1-4, * e1/5/1-4, e1/6/1-4 * Ports 7-34: 40/100GbE Intra-Cluster/HA Ports, int e1/7-34 * Ports 35-36: Intra-Cluster ISL Ports, int e1/35-36 * * Dynamic breakout commands: * 10G: interface breakout module 1 port <range> map 10g-4x * 25G: interface breakout module 1 port <range> map 25g-4x * * Undo breakout commands and return interfaces to 40/100G configuration in * config mode: * no interface breakout module 1 port <range> map 10g-4x * no interface breakout module 1 port <range> map 25g-4x * interface Ethernet <interfaces taken out of breakout mode> * inherit port-profile 40-100G * priority-flow-control mode auto * service-policy input HA * exit * ***************************************************************************
-
Compruebe que el archivo RCF es la versión más reciente correcta:
show running-config
Cuando compruebe la salida para verificar que tiene el RCF correcto, asegúrese de que la siguiente información es correcta:
-
El banner de RCF
-
La configuración del nodo y el puerto
-
Personalizaciones
La salida varía en función de la configuración del sitio. Compruebe la configuración del puerto y consulte las notas de versión para conocer los cambios específicos del RCF que haya instalado.
-
-
Después de comprobar que las versiones de RCF y los ajustes del switch son correctos, copie el archivo running-config en el archivo startup-config.
Para obtener más información acerca de los comandos de Cisco, consulte la guía correspondiente en "Guías de referencia de comandos Cisco Nexus serie 9000 NX-OS".
cs2# copy running-config startup-config [########################################] 100% Copy complete
cs2# reload This command will reboot the system. (y/n)? [n] y
cs2# copy Nexus_9336C_RCF_v1.6-Cluster-HA-Breakout.txt running-config echo-commands cs2# copy running-config startup-config [########################################] 100% Copy complete
-
[[paso 18]]Compruebe el estado de los puertos del clúster.
-
Compruebe que los puertos e0d están en buen estado y en todos los nodos del clúster:
network port show -role cluster
-
cluster1::*> network port show -role cluster Node: cluster1-01 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status ------- --------- ---------------- ---- ---- ------------ -------- ------ e3a Cluster Cluster up 9000 auto/100000 healthy false e3b Cluster Cluster up 9000 auto/100000 healthy false Node: cluster1-02 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status ------- --------- ---------------- ---- ----- ------------ -------- ------ e3a Cluster Cluster up 9000 auto/100000 healthy false e3b Cluster Cluster up 9000 auto/100000 healthy false Node: cluster1-03 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status ------ ---------- ---------------- ---- ----- ----------- -------- ------ e3a Cluster Cluster up 9000 auto/100000 healthy false e0d Cluster Cluster up 9000 auto/100000 healthy false Node: cluster1-04 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status ------ ---------- ---------------- ---- ----- ----------- -------- ------ e3a Cluster Cluster up 9000 auto/100000 healthy false e0d Cluster Cluster up 9000 auto/100000 healthy false 8 entries were displayed.
-
Compruebe el estado del switch del clúster (es posible que no muestre el switch cs2, ya que las LIF no son homadas en el e0d).
cluster1::*> network device-discovery show -protocol cdp Node/ Local Discovered Protocol Port Device (LLDP: ChassisID) Interface Platform ----------- ------ ------------------------- ----------------- -------- cluster1-01/cdp e3a cs1 Ethernet1/7 N9K-C9336C e0d cs2 Ethernet1/7 N9K-C9336C cluster01-2/cdp e3a cs1 Ethernet1/8 N9K-C9336C e0d cs2 Ethernet1/8 N9K-C9336C cluster01-3/cdp e3a cs1 Ethernet1/1/1 N9K-C9336C e3b cs2 Ethernet1/1/1 N9K-C9336C cluster1-04/cdp e3a cs1 Ethernet1/1/2 N9K-C9336C e3b cs2 Ethernet1/1/2 N9K-C9336C cluster1::*> system cluster-switch show -is-monitoring-enabled-operational true Switch Type Address Model --------------------------- ------------------ ---------------- ----- cs1 cluster-network 10.233.205.90 NX9-C9336C Serial Number: FOCXXXXXXGD Is Monitored: true Reason: None Software Version: Cisco Nexus Operating System (NX-OS) Software, Version 9.3(5) Version Source: CDP cs2 cluster-network 10.233.205.91 NX9-C9336C Serial Number: FOCXXXXXXGS Is Monitored: true Reason: None Software Version: Cisco Nexus Operating System (NX-OS) Software, Version 9.3(5) Version Source: CDP 2 entries were displayed.
Puede observar la siguiente salida en la consola del conmutador cs1 dependiendo de la versión RCF cargada previamente en el conmutador. |
2020 Nov 17 16:07:18 cs1 %$ VDC-1 %$ %STP-2-UNBLOCK_CONSIST_PORT: Unblocking port port-channel1 on VLAN0092. Port consistency restored. 2020 Nov 17 16:07:23 cs1 %$ VDC-1 %$ %STP-2-BLOCK_PVID_PEER: Blocking port-channel1 on VLAN0001. Inconsistent peer vlan. 2020 Nov 17 16:07:23 cs1 %$ VDC-1 %$ %STP-2-BLOCK_PVID_LOCAL: Blocking port-channel1 on VLAN0092. Inconsistent local vlan.
-
[[paso 19]]en el switch de clúster cs1, apague los puertos conectados a los puertos del clúster de los nodos. En el ejemplo siguiente se utiliza el resultado del ejemplo de interfaz del paso 1:
cs1(config)# interface eth1/1/1-2,eth1/7-8 cs1(config-if-range)# shutdown
-
[[paso 20]]Compruebe que las LIF del clúster han migrado a los puertos alojados en el switch cs2. Esto puede tardar unos segundos:
network interface show -role cluster
cluster1::*> network interface show -role cluster Logical Status Network Current Current Is Vserver Interface Admin/Oper Address/Mask Node Port Home ------- ------------------ ----------- --------------- ------------ ------- ---- Cluster cluster1-01_clus1 up/up 169.254.3.4/23 cluster1-01 e0d false cluster1-01_clus2 up/up 169.254.3.5/23 cluster1-01 e0d true cluster1-02_clus1 up/up 169.254.3.8/23 cluster1-02 e0d false cluster1-02_clus2 up/up 169.254.3.9/23 cluster1-02 e0d true cluster1-03_clus1 up/up 169.254.1.3/23 cluster1-03 e3b false cluster1-03_clus2 up/up 169.254.1.1/23 cluster1-03 e3b true cluster1-04_clus1 up/up 169.254.1.6/23 cluster1-04 e3b false cluster1-04_clus2 up/up 169.254.1.7/23 cluster1-04 e3b true 8 entries were displayed. cluster1::*>
cluster1::*> cluster show Node Health Eligibility Epsilon -------------------- -------- ------------- ------- cluster1-01 true true false cluster1-02 true true false cluster1-03 true true true cluster1-04 true true false 4 entries were displayed. cluster1::*>
cluster1::*> network interface modify -vserver Cluster -lif * -auto-revert True
cs1# reload This command will reboot the system. (y/n)? [n] y
cs1# show interface brief | grep up . . Eth1/1/1 1 eth access up none 100G(D) -- Eth1/1/2 1 eth access up none 100G(D) -- Eth1/7 1 eth trunk up none 100G(D) -- Eth1/8 1 eth trunk up none 100G(D) -- . .
cs1# show port-channel summary Flags: D - Down P - Up in port-channel (members) I - Individual H - Hot-standby (LACP only) s - Suspended r - Module-removed b - BFD Session Wait S - Switched R - Routed U - Up (port-channel) p - Up in delay-lacp mode (member) M - Not in use. Min-links not met -------------------------------------------------------------------------------- Group Port- Type Protocol Member Ports Channel -------------------------------------------------------------------------------- 1 Po1(SU) Eth LACP Eth1/35(P) Eth1/36(P) cs1#
cluster1::*> network interface show -role cluster Logical Status Network Current Current Is Vserver Interface Admin/Oper Address/Mask Node Port Home ------- ------------------ ---------- ----------------- ----------- ------- ---- Cluster cluster1-01_clus1 up/up 169.254.3.4/23 cluster1-01 e0d true cluster1-01_clus2 up/up 169.254.3.5/23 cluster1-01 e0d true cluster1-02_clus1 up/up 169.254.3.8/23 cluster1-02 e0d true cluster1-02_clus2 up/up 169.254.3.9/23 cluster1-02 e0d true cluster1-03_clus1 up/up 169.254.1.3/23 cluster1-03 e3b true cluster1-03_clus2 up/up 169.254.1.1/23 cluster1-03 e3b true cluster1-04_clus1 up/up 169.254.1.6/23 cluster1-04 e3b true cluster1-04_clus2 up/up 169.254.1.7/23 cluster1-04 e3b true 8 entries were displayed. cluster1::*>
cluster1::*> cluster show Node Health Eligibility Epsilon -------------------- ------- ------------- ------- cluster1-01 true true false cluster1-02 true true false cluster1-03 true true true cluster1-04 true true false 4 entries were displayed. cluster1::*>
cluster1::*> cluster ping-cluster -node local Host is cluster1-03 Getting addresses from network interface table... Cluster cluster1-03_clus1 169.254.1.3 cluster1-03 e3a Cluster cluster1-03_clus2 169.254.1.1 cluster1-03 e3b Cluster cluster1-04_clus1 169.254.1.6 cluster1-04 e3a Cluster cluster1-04_clus2 169.254.1.7 cluster1-04 e3b Cluster cluster1-01_clus1 169.254.3.4 cluster1-01 e3a Cluster cluster1-01_clus2 169.254.3.5 cluster1-01 e0d Cluster cluster1-02_clus1 169.254.3.8 cluster1-02 e3a Cluster cluster1-02_clus2 169.254.3.9 cluster1-02 e0d Local = 169.254.1.3 169.254.1.1 Remote = 169.254.1.6 169.254.1.7 169.254.3.4 169.254.3.5 169.254.3.8 169.254.3.9 Cluster Vserver Id = 4294967293 Ping status: Basic connectivity succeeds on 12 path(s) Basic connectivity fails on 0 path(s) Detected 9000 byte MTU on 12 path(s): Local 169.254.1.3 to Remote 169.254.1.6 Local 169.254.1.3 to Remote 169.254.1.7 Local 169.254.1.3 to Remote 169.254.3.4 Local 169.254.1.3 to Remote 169.254.3.5 Local 169.254.1.3 to Remote 169.254.3.8 Local 169.254.1.3 to Remote 169.254.3.9 Local 169.254.1.1 to Remote 169.254.1.6 Local 169.254.1.1 to Remote 169.254.1.7 Local 169.254.1.1 to Remote 169.254.3.4 Local 169.254.1.1 to Remote 169.254.3.5 Local 169.254.1.1 to Remote 169.254.3.8 Local 169.254.1.1 to Remote 169.254.3.9 Larger than PMTU communication succeeds on 12 path(s) RPC status: 6 paths up, 0 paths down (tcp check) 6 paths up, 0 paths down (udp check)
Instale el RCF en un switch de almacenamiento Cisco Nexus 9336C-FX2
Los archivos de configuración de referencia (RCF) se pueden actualizar en los switches de almacenamiento Cisco Nexus 9336C-FX2.
Antes de actualizar el RCF en el conmutador de almacenamiento deben existir las siguientes condiciones:
-
El conmutador debe estar completamente operativo (no debe haber errores en los registros o problemas similares).
-
Debe haber comprobado o establecido las variables de arranque deseadas en el RCF para reflejar las imágenes de arranque deseadas si sólo está instalando NX-OS y manteniendo su versión actual de RCF.
-
Si necesita cambiar las variables de arranque para reflejar las imágenes de arranque actuales, debe hacerlo antes de volver a aplicar el RCF para que se cree una instancia de la versión correcta en futuros reinicios.
-
Debe haber hecho referencia a las guías de software y actualizaciones adecuadas disponibles en el sitio web de Cisco para obtener documentación completa sobre los procedimientos de actualización y degradación del almacenamiento de Cisco. Consulte "Switches Cisco Nexus serie 9000" si quiere más información.
-
El número de puertos de 100 GbE se define en los archivos de configuración de referencia (RCF) disponibles en la "Switches Ethernet de Cisco" página.
Resumen del procedimiento
-
Comprobar el estado de los switches y los puertos (pasos 1-4)
-
Descargue la imagen de NX-OS al switch cisco st2 y reinicie (pasos 5-8)
-
Copie el RCF al switch cisco st2 (pasos 9-12)
-
Volver a comprobar el estado de los switches y puertos (pasos 13-15)
-
Repita los pasos 1-15 para el switch Cisco st1.
Los resultados del comando pueden variar en función de las diferentes versiones de ONTAP. |
Los ejemplos de este procedimiento utilizan la nomenclatura de conmutador y nodo siguiente:
-
Los nombres de los dos switches de almacenamiento son st1 y st2.
-
Los nodos son 1 y 2.
Para ello, es necesario utilizar tanto comandos de la ONTAP como comandos de la serie Cisco Nexus 9000; los comandos de la ONTAP se usan a menos que se indique lo contrario. |
-
Si se habilita AutoSupport en este clúster, elimine la creación automática de casos invocando un mensaje de AutoSupport:
system node autosupport invoke -node * -type all - message MAINT=xh
Donde x es la duración de la ventana de mantenimiento en horas.
-
Compruebe que estén disponibles los switches de almacenamiento:
system switch ethernet show
storage::*> system switch ethernet show Switch Type Address Model ------------------------- ------------------ ---------------- --------------- st1 storage-network 172.17.227.5 NX9-C9336C Serial Number: FOC221206C2 Is Monitored: true Reason: None Software Version: Cisco Nexus Operating System (NX-OS) Software, Version 9.3(5) Version Source: CDP st2 storage-network 172.17.227.6 NX9-C9336C Serial Number: FOC220443LZ Is Monitored: true Reason: None Software Version: Cisco Nexus Operating System (NX-OS) Software, Version 9.3(5) Version Source: CDP 2 entries were displayed. storage::*>
storage::*> storage port show -port-type ENET Speed VLAN Node Port Type Mode (Gb/s) State Status ID ------- ------- ------- ---------- ---------- --------- ----------- ----- node1 e3a ENET storage 100 enabled online 30 e3b ENET storage 0 enabled offline 30 e7a ENET storage 0 enabled offline 30 e7b ENET storage 100 enabled online 30 node2 e3a ENET storage 100 enabled online 30 e3b ENET storage 0 enabled offline 30 e7a ENET storage 0 enabled offline 30 e7b ENET storage 100 enabled online 30
storage::*> system health alert show -instance There are no entries matching your query.
st2# install all nxos bootflash:nxos.9.3. 5.bin Installer will perform compatibility check first. Please wait. Installer is forced disruptive Verifying image bootflash:/nxos.9.3.4.bin for boot variable "nxos". [####################] 100% -- SUCCESS Verifying image type. [[####################] 100% -- SUCCESS Preparing "nxos" version info using image bootflash:/nxos.9.3.4.bin. [####################] 100% -- SUCCESS Preparing "bios" version info using image bootflash:/nxos.9.3.4.bin. [####################] 100% -- SUCCESS Performing module support checks. [####################] 100% -- SUCCESS Notifying services about system upgrade. [####################] 100% -- SUCCESS Compatibility check is done: Module bootable Impact Install-type Reason ------ -------- ----- -------- ------------ ---- -- 1 yes disruptive reset default upgrade is not hitless Images will be upgraded according to following table: Module Image Running-Version(pri:alt) New-Version Upg Required ------ -------- --------------------------------------- ------------ -------- 1 nxos 9.3(3) 9.3(4) yes 1 bios v08.37(01/28/2020):v08.23(09/23/2015) v08.38(05/29/2020) no Switch will be reloaded for disruptive upgrade. Do you want to continue with the installation (y/n)? [n] y input string too long Do you want to continue with the installation (y/n)? [n] y Install is in progress, please wait. Performing runtime checks. [####################] 100% -- SUCCESS Setting boot variables. [####################] 100% -- SUCCESS Performing configuration copy. [####################] 100% -- SUCCESS Module 1: Refreshing compact flash and upgrading bios/loader/bootrom. Warning: please do not remove or power off the module at this time. [####################] 100% -- SUCCESS Finishing the upgrade, switch will reboot in 10 seconds. st2#
st2# copy running-config startup-config [########################################] 100% Copy complete. st2# reload This command will reboot the system. (y/n)? [n] y
st2# show version Cisco Nexus Operating System (NX-OS) Software TAC support: http://www.cisco.com/tac Upgrading a Cisco Nexus 9336C Storage Switch 6 Upgrading a Cisco Nexus 9336C storage switch Copyright (C) 2002-2020, Cisco and/or its affiliates. All rights reserved. The copyrights to certain works contained in this software are owned by other third parties and used and distributed under their own licenses, such as open source. This software is provided "as is," and unless otherwise stated, there is no warranty, express or implied, including but not limited to warranties of merchantability and fitness for a particular purpose. Certain components of this software are licensed under the GNU General Public License (GPL) version 2.0 or GNU General Public License (GPL) version 3.0 or the GNU Lesser General Public License (LGPL) Version 2.1 or Lesser General Public License (LGPL) Version 2.0. A copy of each such license is available at http://www.opensource.org/licenses/gpl-2.0.php and http://opensource.org/licenses/gpl-3.0.html and http://www.opensource.org/licenses/lgpl-2.1.php and . Software BIOS: version 08.38 NXOS: version 9.3(5) BIOS compile time: 05/29/2020 NXOS image file is: bootflash:///nxos.9.3. 5.bin NXOS compile time: 4/28/2020 21:00:00 [04/29/2020 02:28:31] Hardware cisco Nexus9000 C9336C Chassis (Nexus 9000 Series) Intel(R) Xeon(R) CPU E5-2403 v2 @ 1.80GHz with 8154432 kB of memory. Processor Board ID FOC20291J6K Device name: S2 bootflash: 53298520 kB Kernel uptime is 0 day(s), 0 hour(s), 3 minute(s), 42 second(s) Last reset at 157524 usecs after Mon Nov 2 18:32:06 2020 Reason: Reset due to upgrade System version: 9.3(5) Service: plugin Core Plugin, Ethernet Plugin Active Package(s): st2#
-
copie el RCF en el conmutador st2 en el bootflash del conmutador utilizando uno de los siguientes protocolos de transferencia: FTP, HTTP, TFTP, SFTP o SCP.
Para obtener más información acerca de los comandos de Cisco, consulte la guía correspondiente en "Guías de referencia de comandos Cisco Nexus serie 9000 NX-OS".
El ejemplo siguiente muestra que se está utilizando HTTP para copiar un RCF al bootflash en el switch st2:
st2# copy http://172.16.10.1//cfg/Nexus_9336C_RCF_v1.6-Storage.txt bootflash: vrf management % Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed 100 3254 100 3254 0 0 8175 0 --:--:-- --:--:-- --:--:– 8301 Copy complete, now saving to disk (please wait)... Copy complete. st2#
st2# copy Nexus_9336C_RCF_v1.6-Storage.txt running-config echo-commands
-
Compruebe que el archivo RCF es la versión más reciente correcta:
show running-config
Cuando compruebe la salida para verificar que tiene el RCF correcto, asegúrese de que la siguiente información es correcta:
-
El banner de RCF
-
La configuración del nodo y el puerto
-
Personalizaciones
La salida varía en función de la configuración del sitio. Compruebe la configuración del puerto y consulte las notas de versión para conocer los cambios específicos del RCF que haya instalado.
Importante: en la salida de banner de
show banner motd
Debe leer y seguir las instrucciones de la sección *NOTAS IMPORTANTES *para garantizar la configuración y el funcionamiento correctos del interruptor. -
st2# show banner motd ****************************************************************************** *NetApp Reference Configuration File (RCF) * *Switch : Nexus N9K-C9336C-FX2 *Filename : Nexus_9336C_RCF_v1.6-Storage.txt * Date : 10-23-2020 *Version : v1.6 * *Port Usage: Storage configuration *Ports 1-36: 100GbE Controller and Shelf Storage Ports * *IMPORTANT NOTES* *- This RCF utilizes QoS and requires TCAM re-configuration, requiring RCF *to be loaded twice with the Storage Switch rebooted in between. * *- Perform the following 4 steps to ensure proper RCF installation: * *(1) Apply RCF first time, expect following messages: *- Please save config and reload the system... *- Edge port type (portfast) should only be enabled on ports... *- TCAM region is not configured for feature QoS class IPv4 ingress... * *(2) Save running-configuration and reboot Cluster Switch * *(3) After reboot, apply same RCF second time and expect following messages: *- % Invalid command at '^' marker *- Syntax error while parsing... * *(4) Save running-configuration again ****************************************************************************** st2#
-
después de comprobar que las versiones de software y los ajustes del switch son correctos, copie el archivo running-config en el archivo startup-config en el conmutador st2.
Para obtener más información acerca de los comandos de Cisco, consulte la guía correspondiente en "Guías de referencia de comandos Cisco Nexus serie 9000 NX-OS".
En el siguiente ejemplo se muestra el
running-config
el archivo se ha copiado correctamente enstartup-config
archivo:
st2# copy running-config startup-config [########################################] 100% Copy complete.
storage::*> system switch ethernet show Switch Type Address Model ---------------------------- ------------------ ---------------- --------------- st1 storage-network 172.17.227.5 NX9-C9336C Serial Number: FOC221206C2 Is Monitored: true Reason: None Software Version: Cisco Nexus Operating System (NX-OS) Software, Version 9.3(5) Version Source: CDP st2 storage-network 172.17.227.6 NX9-C9336C Serial Number: FOC220443LZ Is Monitored: true Reason: None Software Version: Cisco Nexus Operating System (NX-OS) Software, Version 9.3(5) Version Source: CDP 2 entries were displayed. storage::*
storage::*> storage port show -port-type ENET Speed VLAN Node Port Type Mode (Gb/s) State Status ID ------- ------- ------- ---------- ----------- --------- --------- ----- node1 e3a ENET storage 100 enabled online 30 e3b ENET storage 0 enabled offline 30 e7a ENET storage 0 enabled offline 30 e7b ENET storage 100 enabled online 30 node2 e3a ENET storage 100 enabled online 30 e3b ENET storage 0 enabled offline 30 e7a ENET storage 0 enabled offline 30 e7b ENET storage 100 enabled online 30
storage::*> system health alert show -instance There are no entries matching your query.
Instale el RCF en un switch compartido Cisco Nexus 9336C-FX2
Desde ONTAP 9.9.1, puede utilizar los switches Cisco Nexus 9336C-FX2 para combinar las funciones de almacenamiento y clúster en un escenario de switch compartido.
-
Los switches del clúster deben funcionar correctamente (no deben haber errores en los registros ni problemas similares).
-
Los switches de almacenamiento deben funcionar correctamente (no deben haber errores en los registros ni problemas similares).
-
Los nombres de los dos conmutadores de almacenamiento son sh1 y sh2.
-
El ejemplo utilizado aquí carga el RCF compartido en el nuevo conmutador.
-
Copie el RCF del switch sh2 en el bootflash del switch utilizando uno de los siguientes protocolos de transferencia: FTP, HTTP, TFTP, SFTP o SCP.
Para obtener más información acerca de los comandos de Cisco, consulte la guía correspondiente en "Guías de referencia de comandos Cisco Nexus serie 9000 NX-OS".
En el ejemplo siguiente se muestra el uso de HTTP para copiar un RCF al flash de inicio del conmutador sh2:
sh2# copy http://172.16.10.1//cfg/Nexus_9336C_RCF_v1.7-Cluster-Ha-Storage.txt bootflash: vrf management % Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed 100 5143 100 5143 0 0 11300 0 --:--:-- --:--:-- --:--:– 11300 Copy complete, now saving to disk (please wait)... Copy complete. sh2#
sh2# copy Nexus_9336C_RCF_v1.7-Cluster-HA-Storage.txt running-config echo-commands
-
Compruebe que el archivo RCF es la versión más reciente correcta:
show running-config
Cuando compruebe la salida para verificar que tiene el RCF correcto, asegúrese de que la siguiente información es correcta:
-
El banner de RCF
-
La configuración del nodo y el puerto
-
Personalizaciones
La salida varía en función de la configuración del sitio. Compruebe la configuración del puerto y consulte las notas de versión para conocer los cambios específicos del RCF que haya instalado.
Importante: en la salida de banner de
show banner motd
Debe leer y seguir las instrucciones de la sección *NOTAS IMPORTANTES *para garantizar la configuración y el funcionamiento correctos del interruptor. -
sh2# show banner motd ****************************************************************************** *NetApp Reference Configuration File (RCF) * *Switch : Nexus N9K-C9336C-FX2 *Filename : Nexus_9336C_RCF_v1.7-Cluster-HA-Storage.txt * Date : Jan-08-2021 *Version : v1.7 * *Port Usage: *Ports 1-8: 40/100GbE Intra-Cluster/HA Ports, int e1/1-8 *Port 9: 10GbE breakout Intra-Cluster Ports, int e1/9/1-4 *Port 10: 25GbE breakout Intra-Cluster/HA Ports, int e1/10/1-4 *Ports 11-22: First HA-pair Controller and Shelf Storage Ports, int e1/11-22 *Ports 23-34: Second HA-pair Controller and Shelf Storage Ports, int e1/23-34 *Ports 35-36: Intra-Cluster ISL Ports, int e1/35-36 * * Undo breakout commands and return interfaces to 40/100G configuration in * config mode: * no interface breakout module 1 port 9 map 10g-4x * no interface breakout module 1 port 10 map 25g-4x * interface Ethernet 1/9-10 * inherit port-profile CLUSTER_HA * priority-flow-control mode auto * service-policy type qos input HA_POLICY * exit * *IMPORTANT NOTES* * In certain conditions, N9K-C9336C-FX2 may not be able to auto-negotiate port * speed correctly, and port speed must be manually set, in config mode, e.g. * int e1/1 * speed 40000 * int e1/3 * speed 100000 * ****************************************************************************** sh2#
-
después de verificar que las versiones de software y los ajustes del switch son correctos, copie el
running-config
archivo al archivo de configuración de inicio en el conmutador sh2.Para obtener más información acerca de los comandos de Cisco, consulte la guía correspondiente en "Guías de referencia de comandos Cisco Nexus serie 9000 NX-OS".
En el siguiente ejemplo se muestra el
running-config
el archivo se ha copiado correctamente enstartup-config
archivo:
sh2# copy running-config startup-config [########################################] 100% Copy complete.