Skip to main content
StorageGRID Appliances

Access StorageGRID Appliance Installer

Contributors netapp-perveilerk netapp-ivanad netapp-pcarriga
PDFs

You must access the StorageGRID Appliance Installer to verify the installer version and configure the connections between the appliance and the three StorageGRID networks: the Grid Network, the Admin Network (optional), and the Client Network (optional).

Before you begin

  • You are using any management client that can connect to the StorageGRID Admin Network, or you have a service laptop.

  • The client or service laptop has a supported web browser.

  • The services appliance or storage appliance controller is connected to all of the StorageGRID networks you plan to use.

  • You know the IP address, gateway, and subnet for the services appliance or storage appliance controller on these networks.

  • You have configured the network switches you plan to use.

About this task

To initially access the StorageGRID Appliance Installer, you can use the DHCP-assigned IP address for the Admin Network port on the services appliance or storage appliance controller (assuming it is connected to the Admin Network), or you can connect a service laptop directly to the services appliance or storage appliance controller.

Steps

  1. If possible, use the DHCP address for the Admin Network port on the services appliance or storage appliance controller. The Admin Network port is highlighted in the following figure. (Use the IP address on the Grid Network if the Admin Network is not connected.)

    SG100
    Admin Network port on the SG100
    SG110
    Admin Network port on the SG110
    SG1000
    Admin Network port on the SG1000
    SG1100
    Admin Network port on the SG1100
    E5700SG

    For the E5700SG, you can do either of the following:

    • Look at the seven-segment display on the E5700SG controller. If management port 1 and 10/25-GbE ports 2 and 4 on the E5700SG controller are connected to networks with DHCP servers, the controller attempts to obtain dynamically assigned IP addresses when you power on the enclosure. After the controller has completed the power-on process, its seven-segment display shows HO, followed by a repeating sequence of two numbers.

      HO -- IP address for Admin Network -- IP address for Grid Network HO

      In the sequence:

      • The first set of numbers is the DHCP address for the appliance Storage Node on the Admin Network, if it is connected. This IP address is assigned to management port 1 on the E5700SG controller.

      • The second set of numbers is the DHCP address for the appliance Storage Node on the Grid Network. This IP address is assigned to 10/25-GbE ports 2 and 4 when you first apply power to the appliance.

        Note If an IP address could not be assigned using DHCP, 0.0.0.0 is displayed.
    SG5800
    Admin Network port on the SG5800 controller
    SG6000-CN
    Admin Network port on the SG6000-CN controller
    SG6100-CN
    Admin Network port on the SG6000-CN controller
    SGF6112
    Admin Network port on the SGF6112

    1. Obtain the DHCP address for the appliance on the Admin Network from your network administrator.

    2. From the client, enter this URL for the StorageGRID Appliance Installer:
      https://Appliance_IP:8443

      For Appliance_IP, use the DHCP address (use the IP address for the Admin Network if you have it).

    3. If you are prompted with a security alert, view and install the certificate using the browser's installation wizard.

      The alert will not appear the next time you access this URL.

      The StorageGRID Appliance Installer Home page appears. The information and messages shown when you first access this page depend on how your appliance is currently connected to StorageGRID networks. Error messages might appear that will be resolved in later steps.

      Screen shot of the top part of the StorageGRID Appliance Installer home page

  2. If you can't obtain an IP address using DHCP, you can use a link-local connection.

    SG100

    Connect a service laptop directly to the rightmost RJ-45 port on the services appliance, using an Ethernet cable.

    SG100 Link-Local Connection
    SG110

    Connect a service laptop directly to the rightmost RJ-45 port on the appliance, using an Ethernet cable.

    SG110 Link-Local Connection
    SG1000

    Connect a service laptop directly to the rightmost RJ-45 port on the services appliance, using an Ethernet cable.

    SG1000 Link-Local Connection
    SG1100

    Connect a service laptop directly to the rightmost RJ-45 port on the appliance, using an Ethernet cable.

    SG1100 Link-Local Connection
    E5700SG

    Connect the service laptop to management port 2 on the E5700SG controller, using an Ethernet cable.

    Location of Management Port 2 on the E5700SG controller
    SG5800

    Connect the service laptop to management port 1 on the SG5800 controller, using an Ethernet cable.

    Location of Management Port 1 on the SG5800 controller
    SG6000-CN

    Connect a service laptop directly to the rightmost RJ-45 port on the SG6000-CN controller, using an Ethernet cable.

    Location of Management Port for SG6000-CN
    SG6100-CN

    Connect a service laptop directly to the rightmost RJ-45 port on the SG6100-CN controller, using an Ethernet cable.

    Location of Management Port for SG6100-CN
    SGF6112

    Connect a service laptop directly to the rightmost RJ-45 port on the appliance, using an Ethernet cable.

    SGF6112 Link-Local Connection

    1. Open a web browser on the service laptop.

    2. Enter this URL for the StorageGRID Appliance Installer:
      https://169.254.0.1:8443

      The StorageGRID Appliance Installer Home page appears. The information and messages shown when you first access this page depend on how your appliance is currently connected to StorageGRID networks. Error messages might appear that will be resolved in later steps.

      Note If you can't access the Home page over a link-local connection, configure the service laptop IP address as 169.254.0.2, and try again.
After you finish

After accessing the StorageGRID Appliance Installer:

  • Verify that the StorageGRID Appliance Installer version on the appliance matches the software version installed on your StorageGRID system. Upgrade StorageGRID Appliance Installer, if necessary.

    Verify and upgrade StorageGRID Appliance Installer version

  • Review any messages displayed on the StorageGRID Appliance Installer Home page and configure the link configuration and the IP configuration, as required.

    Appliance Installer Home