Skip to main content
ONTAP MetroCluster
본 한국어 번역은 사용자 편의를 위해 제공되는 기계 번역입니다. 영어 버전과 한국어 버전이 서로 어긋나는 경우에는 언제나 영어 버전이 우선합니다.

Cisco FC 스위치를 출하 시 기본값으로 재설정합니다

기여자

새 소프트웨어 버전과 RCFs를 설치하기 전에 Cisco 스위치 구성을 지우고 기본 구성을 수행해야 합니다.

이 작업에 대해

MetroCluster 패브릭 구성의 각 FC 스위치에 대해 이러한 단계를 반복해야 합니다.

참고 표시된 출력은 Cisco IP 스위치용으로 표시되지만 Cisco FC 스위치에도 적용할 수 있습니다.
단계
  1. 스위치를 출하 시 기본값으로 재설정합니다.

    1. 기존 구성 지우기: + `* 쓰기 지우기 * '

    2. 스위치 소프트웨어를 다시 로드합니다: + " * reload * "

      시스템이 재부팅되고 구성 마법사가 시작됩니다. 부팅 중에 Auto Provisioning 중단 메시지가 표시된 후 정상 설치를 계속하면(예/아니요) [n] "* yes*"로 응답하여 계속 진행해야 합니다.

    3. 구성 마법사에서 기본 스위치 설정을 입력합니다.

      • 관리자 암호입니다

      • 스위치 이름

      • 대역외 관리 구성

      • 기본 게이트웨이

      • SSH 서비스(원격 지원 에이전트)

        구성 마법사를 완료하면 스위치가 재부팅됩니다.

    4. 메시지가 표시되면 사용자 이름과 암호를 입력하여 스위치에 로그인합니다.

      다음 예에서는 스위치에 로그인할 때 프롬프트와 시스템 응답을 보여 줍니다. 꺾쇠 괄호(' * << * ')는 사용자가 정보를 입력하는 위치를 표시합니다.

      ---- System Admin Account Setup ----
      Do you want to enforce secure password standard (yes/no) [y]:y  **<<<**
      
          Enter the password for "admin": password  **<<<**
        Confirm the password for "admin": password  **<<<**
               ---- Basic System Configuration Dialog VDC: 1 ----
      
      This setup utility will guide you through the basic configuration of
      the system. Setup configures only enough connectivity for management
      of the system.
      
      Please register Cisco Nexus3000 Family devices promptly with your
      supplier. Failure to register may affect response times for initial
      service calls. Nexus3000 devices must be registered to receive
      entitled support services.
      
      Press Enter at anytime to skip a dialog. Use ctrl-c at anytime
      to skip the remaining dialogs.
    5. 스위치 이름, 관리 주소 및 게이트웨이를 포함한 다음 프롬프트 세트에 기본 정보를 입력하고, 다음 예에서와 같이 SSH 키에 대해 ' * RSA * '를 입력합니다.

      Would you like to enter the basic configuration dialog (yes/no): yes
        Create another login account (yes/no) [n]:
        Configure read-only SNMP community string (yes/no) [n]:
        Configure read-write SNMP community string (yes/no) [n]:
        Enter the switch name : switch-name **<<<**
        Continue with Out-of-band (mgmt0) management configuration? (yes/no) [y]:
          Mgmt0 IPv4 address : management-IP-address  **<<<**
          Mgmt0 IPv4 netmask : management-IP-netmask  **<<<**
        Configure the default gateway? (yes/no) [y]: y **<<<**
          IPv4 address of the default gateway : gateway-IP-address  **<<<**
        Configure advanced IP options? (yes/no) [n]:
        Enable the telnet service? (yes/no) [n]:
        Enable the ssh service? (yes/no) [y]: y  **<<<**
          Type of ssh key you would like to generate (dsa/rsa) [rsa]: rsa **<<<**
          Number of rsa key bits <1024-2048> [1024]:
        Configure the ntp server? (yes/no) [n]:
        Configure default interface layer (L3/L2) [L2]:
        Configure default switchport interface state (shut/noshut) [noshut]: shut **<<<**
        Configure CoPP system profile (strict/moderate/lenient/dense) [strict]:

      마지막 프롬프트 세트가 구성을 완료합니다.

    The following configuration will be applied:
      password strength-check
      switchname IP_switch_A_1
    vrf context management
    ip route 0.0.0.0/0 10.10.99.1
    exit
      no feature telnet
      ssh key rsa 1024 force
      feature ssh
      system default switchport
      system default switchport shutdown
      copp profile strict
    interface mgmt0
    ip address 10.10.99.10 255.255.255.0
    no shutdown
    
    Would you like to edit the configuration? (yes/no) [n]:
    
    Use this configuration and save it? (yes/no) [y]:
    2017 Jun 13 21:24:43 A1 %$ VDC-1 %$ %COPP-2-COPP_POLICY: Control-Plane is protected with policy copp-system-p-policy-strict.
    
    [########################################] 100%
    Copy complete.
    
    User Access Verification
    IP_switch_A_1 login: admin
    Password:
    Cisco Nexus Operating System (NX-OS) Software
    .
    .
    .
    IP_switch_A_1#
  2. 구성을 저장합니다.

    IP_switch_A_1# copy running-config startup-config
  3. 스위치를 재부팅하고 스위치가 다시 로드될 때까지 기다립니다.

    IP_switch_A_1# reload
  4. MetroCluster 패브릭 구성의 다른 3개 스위치에 대해 이전 단계를 반복합니다.