이더넷 스위치 상태 모니터링 로그 수집
이더넷 스위치 상태 모니터(CSHM)는 클러스터 및 스토리지 네트워크 스위치의 작동 상태를 확인하고 디버깅을 위한 스위치 로그를 수집하는 역할을 담당합니다. 이 절차는 스위치에서 자세한 * 지원 * 로그 수집을 설정 및 시작하는 프로세스를 안내하고 AutoSupport에서 수집하는 * 주기적 * 데이터의 시간별 수집을 시작합니다.
-
RCF(Reference Configuration File)가 적용될 때 로그 수집용 사용자를 지정해야 합니다. 기본적으로 이 사용자는 'admin'으로 설정됩니다. 다른 사용자를 사용하려면 RCF의 *#SHM 사용자*s 섹션에서 이를 지정해야 합니다.
-
사용자는 * NV show * 명령에 액세스할 수 있어야 합니다. 이 기능은 를 실행하여 추가할 수 있습니다
sudo adduser USER nv show
사용자를 로그 수집용 사용자로 바꿉니다. -
스위치에 대해 스위치 상태 모니터링을 활성화해야 합니다. 를 확인하여 확인합니다
Is Monitored:
의 출력에서 필드는 * true * 로 설정됩니다system switch ethernet show
명령.
-
로그 수집을 설정하려면 각 스위치에 대해 다음 명령을 실행합니다. 로그 수집을 위해 스위치 이름, 사용자 이름 및 암호를 입력하라는 메시지가 표시됩니다.
'System switch Ethernet log setup - password'(시스템 스위치 이더넷 로그 설정 - 암호)
예제 보기
cluster1::*> system switch ethernet log setup-password Enter the switch name: <return> The switch name entered is not recognized. Choose from the following list: cs1 cs2 cluster1::*> system switch ethernet log setup-password Enter the switch name: cs1 Would you like to specify a user other than admin for log collection? {y|n}: n Enter the password: <enter switch password> Enter the password again: <enter switch password> cluster1::*> system switch ethernet log setup-password Enter the switch name: cs2 Would you like to specify a user other than admin for log collection? {y|n}: n Enter the password: <enter switch password> Enter the password again: <enter switch password>
-
로그 수집을 시작하려면 다음 명령을 실행하여 디바이스를 이전 명령에서 사용한 스위치로 바꿉니다. 이렇게 하면 두 가지 유형의 로그 수집이 시작됩니다. 세부 정보
Support
의 로그 및 시간별 컬렉션Periodic
정규화해야 합니다.system switch ethernet log modify -device <switch-name> -log-request true
예제 보기
cluster1::*> system switch ethernet log modify -device cs1 -log-request true Do you want to modify the cluster switch log collection configuration? {y|n}: [n] y Enabling cluster switch log collection. cluster1::*> system switch ethernet log modify -device cs2 -log-request true Do you want to modify the cluster switch log collection configuration? {y|n}: [n] y Enabling cluster switch log collection.
10분간 기다린 후 로그 수집이 완료되었는지 확인합니다.
system switch ethernet log show
이러한 명령 중 하나라도 오류를 반환하거나 로그 수집이 완료되지 않으면 NetApp 지원에 문의하십시오.
로그 수집 기능에 의해 보고되는 다음 오류 상태 중 하나가 발생하는 경우( 의 출력에 표시됨 system switch ethernet log show
), 해당 디버그 단계를 시도해 봅니다.
* 로그 수집 오류 상태 * |
* 해상도 * |
*RSA 키가 없습니다 |
ONTAP SSH 키를 재생성합니다. NetApp 지원 부서에 문의하십시오. |
|
자격 증명을 확인하고, SSH 연결을 테스트하고, ONTAP SSH 키를 다시 생성합니다. 스위치 설명서를 검토하거나 NetApp 지원에 문의하여 지침을 받으십시오. |
*FIPS*에 대한 ECDSA 키가 없습니다 |
FIPS 모드가 활성화된 경우 재시도하기 전에 스위치에서 ECDSA 키를 생성해야 합니다. |
|
에 있는 이전 로그 수집 디렉터리와 '.tar' 파일을 제거합니다 |
|
스위치 사용자에게 로그 수집 권한이 있는지 확인합니다. 위의 필수 구성 요소를 참조하십시오. |