본 한국어 번역은 사용자 편의를 위해 제공되는 기계 번역입니다. 영어 버전과 한국어 버전이 서로 어긋나는 경우에는 언제나 영어 버전이 우선합니다.

NX-OS 소프트웨어 설치 또는 업그레이드

07/21/2026 기여자

PDF

Nexus 9336C-FX2 및 9336C-FX2-T 클러스터 스위치에 NX-OS 소프트웨어를 설치하거나 업그레이드하려면 다음 절차를 따르세요.

시작하기 전에 다음 절차를 완료하세요."NX-OS 및 RCF 설치 준비" .

NetApp은 ONTAP 소프트웨어 업그레이드를 먼저 완료한 다음 스위치 소프트웨어 업그레이드를 수행할 것을 권장합니다.

검토 요구 사항

시작하기 전에

다음을 수행해야 합니다:

스위치에서 show install all impact nxos bootflash:<image_name>.bin 명령을 실행하여 새 NX-OS 소프트웨어 이미지 설치 또는 업그레이드의 영향을 검토하십시오. 이미지 무결성을 확인하고, 필요한 재부팅을 점검하며, 하드웨어 호환성을 평가하고, 충분한 공간이 있는지 확인합니다.
대상 NX-OS 소프트웨어 버전의 릴리스 노트를 검토하여 특정 요구 사항이 있는지 확인하십시오.
스위치 구성의 현재 백업이 있는지 확인합니다.
완전히 작동하는 클러스터가 있는지 확인하십시오(로그에 오류가 없거나 유사한 문제가 없는지 확인).

제안된 문서

"Cisco 이더넷 스위치 페이지"

지원되는 ONTAP 및 NX-OS 버전에 대한 스위치 호환성 표를 참조하세요.
"소프트웨어 업그레이드 및 다운그레이드 가이드"

Cisco 소프트웨어 업그레이드 및 다운그레이드 가이드는 Cisco 웹사이트를 참조하십시오.
"Cisco Nexus 9000 및 3000 업그레이드 및 ISSU 매트릭스"

현재 및 대상 릴리스를 기반으로 Nexus 9000 시리즈 스위치의 Cisco NX-OS 소프트웨어에 대한 중단적 업그레이드/다운그레이드에 대한 정보를 제공합니다.

해당 페이지에서 *중단 업그레이드*를 선택하고 드롭다운 목록에서 현재 릴리스와 대상 릴리스를 선택합니다.

예시에 관하여

이 절차의 예에서는 다음 스위치 및 노드 명명법을 사용합니다.

두 Cisco 스위치의 이름은 cs1과 cs2입니다.
노드 이름은 cluster1-01, cluster1-02, cluster1-03, cluster1-04입니다.
클러스터 LIF 이름은 cluster1-01_clus1, cluster1-01_clus2, cluster1-02_clus1, cluster1-02_clus2, cluster1-03_clus1, cluster1-03_clus2, cluster1-04_clus1 및 cluster1-04_clus2입니다.
그만큼 cluster1::*> 프롬프트는 클러스터의 이름을 나타냅니다.

소프트웨어를 설치하세요

이 절차에서는 Cisco Nexus 9000 Series Switch 명령이 지정되지 않은 경우 ONTAP 명령을 사용하십시오.

단계

클러스터 스위치를 관리 네트워크에 연결합니다.
ping 명령을 사용하여 NX-OS 소프트웨어와 RCF를 호스팅하는 서버에 대한 연결을 확인합니다.

ping <IP address> vrf management
예를 보여주세요
이 예제에서는 스위치가 IP 주소 172.19.2.1의 서버에 도달할 수 있는지 확인합니다.
cs2# ping 172.19.2.1 vrf management Pinging 172.19.2.1 with 0 bytes of data: Reply From 172.19.2.1: icmp_seq = 0. time= 5910 usec.

클러스터 스위치에 연결된 각 노드의 클러스터 포트를 표시합니다.

network device-discovery show

예를 보여주세요

cluster1::*> network device-discovery show
Node/       Local  Discovered
Protocol    Port   Device (LLDP: ChassisID)  Interface         Platform
----------- ------ ------------------------- ----------------- --------------
cluster1-01/cdp
            e0a    cs1                       Ethernet1/7       N9K-C9336C-FX2
            e0b    cs2                       Ethernet1/7       N9K-C9336C-FX2
cluster1-02/cdp
            e0a    cs1                       Ethernet1/8       N9K-C9336C-FX2
            e0b    cs2                       Ethernet1/8       N9K-C9336C-FX2
cluster1-03/cdp
            e0a    cs1                       Ethernet1/1/1     N9K-C9336C-FX2
            e0b    cs2                       Ethernet1/1/1     N9K-C9336C-FX2
cluster1-04/cdp
            e0a    cs1                       Ethernet1/1/2     N9K-C9336C-FX2
            e0b    cs2                       Ethernet1/1/2     N9K-C9336C-FX2
cluster1::*>

각 클러스터 포트의 관리 및 운영 상태를 확인합니다.

모든 클러스터 포트가 정상 상태로 *작동*되어 있는지 확인하세요.

network port show -ipspace Cluster

예를 보여주세요

cluster1::*> network port show -ipspace Cluster

Node: cluster1-01
                                                                        Ignore
                                                  Speed(Mbps)  Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper   Status   Status
--------- ------------ ---------------- ---- ---- ------------ -------- ------
e0a       Cluster      Cluster          up   9000  auto/100000 healthy  false
e0b       Cluster      Cluster          up   9000  auto/100000 healthy  false

Node: cluster1-02
                                                                        Ignore
                                                  Speed(Mbps)  Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper   Status   Status
--------- ------------ ---------------- ---- ---- ------------ -------- ------
e0a       Cluster      Cluster          up   9000  auto/100000 healthy  false
e0b       Cluster      Cluster          up   9000  auto/100000 healthy  false

Node: cluster1-03

                                                                        Ignore
                                                  Speed(Mbps)  Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper   Status   Status
--------- ------------ ---------------- ---- ---- ------------ -------- ------
e0a       Cluster      Cluster          up   9000  auto/100000 healthy  false
e0b       Cluster      Cluster          up   9000  auto/100000 healthy  false

Node: cluster1-04
                                                                        Ignore
                                                  Speed(Mbps)  Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper   Status   Status
--------- ------------ ---------------- ---- ---- ------------ -------- ------
e0a       Cluster      Cluster          up   9000  auto/100000 healthy  false
e0b       Cluster      Cluster          up   9000  auto/100000 healthy  false
cluster1::*>

모든 클러스터 인터페이스(LIF)가 홈 포트에 있는지 확인하세요.

network interface show -vserver Cluster

예를 보여주세요

cluster1::*> network interface show -vserver Cluster
            Logical            Status     Network            Current             Current Is
Vserver     Interface          Admin/Oper Address/Mask       Node                Port    Home
----------- ------------------ ---------- ------------------ ------------------- ------- ----
Cluster
            cluster1-01_clus1  up/up      169.254.3.4/23     cluster1-01         e0b     true
            cluster1-01_clus2  up/up      169.254.3.5/23     cluster1-01         e0b     true
            cluster1-02_clus1  up/up      169.254.3.8/23     cluster1-02         e0b     true
            cluster1-02_clus2  up/up      169.254.3.9/23     cluster1-02         e0b     true
            cluster1-03_clus1  up/up      169.254.1.3/23     cluster1-03         e0b     true
            cluster1-03_clus2  up/up      169.254.1.1/23     cluster1-03         e0b     true
            cluster1-04_clus1  up/up      169.254.1.6/23     cluster1-04         e0b     true
            cluster1-04_clus2  up/up      169.254.1.7/23     cluster1-04         e0b     true
cluster1::*>

클러스터가 두 클러스터 스위치에 대한 정보를 모두 표시하는지 확인합니다.

system cluster-switch show -is-monitoring-enabled-operational true

예를 보여주세요

cluster1::*> system cluster-switch show -is-monitoring-enabled-operational true
Switch                      Type               Address          Model
--------------------------- ------------------ ---------------- --------------
cs1                         cluster-network    10.233.205.90    N9K-C9336C-FX2
     Serial Number: FOCXXXXXXGD
      Is Monitored: true
            Reason: None
  Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                    9.3(5)
    Version Source: CDP

cs2                         cluster-network    10.233.205.91    N9K-C9336C-FX2
     Serial Number: FOCXXXXXXGS
      Is Monitored: true
            Reason: None
  Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                    9.3(5)
    Version Source: CDP
cluster1::*>

클러스터 LIF에서 자동 되돌리기를 비활성화합니다. 클러스터 LIF는 파트너 클러스터 스위치로 장애 조치되고 대상 스위치에서 업그레이드 절차를 수행하는 동안 해당 위치에 남아 있습니다.

network interface modify -vserver Cluster -lif * -auto-revert false
NX-OS 소프트웨어와 EPLD 이미지를 다운로드하여 설치하십시오. 설치 단계는 현재 사용 중인 NX-OS 버전과 설치 대상 NX-OS 버전에 따라 다를 수 있습니다.

본인의 상황에 맞는 탭을 선택하십시오.
- 10.4(5)(M)으로 업그레이드
- 10.4(5)(M) 이전 버전에서 10.5(3)(F) 이후 버전으로 업그레이드
- 10.5(3)(F)에서 이후 버전으로 업그레이드

10.4(5)(M)으로 업그레이드

NX-OS 소프트웨어와 EPLD 이미지를 Nexus 9336C-FX2 스위치에 복사합니다.

copy <protocol>: bootflash: vrf management

예

cs2# *copy sftp: bootflash: vrf management*
Enter source filename: */code/nxos.10.4.5.M.bin*
Enter hostname for the sftp server: *172.19.2.1*
Enter username: *user1*

Outbound-ReKey for 172.19.2.1:22
Inbound-ReKey for 172.19.2.1:22
user1@172.19.2.1's password:
sftp> *progress*
Progress meter enabled
sftp> *get /code/nxos.10.4.5.M.bin /bootflash/nxos.10.4.5.M.bin*
/code/nxos.10.4.5.M.bin  100% 1261MB   9.3MB/s   02:15
sftp> *exit*
Copy complete, now saving to disk (please wait)...
Copy complete.


cs2# *copy sftp: bootflash: vrf management*
Enter source filename: */code/n9000-epld.10.4.5.M.img*
Enter hostname for the sftp server: *172.19.2.1*
Enter username: *user1*

Outbound-ReKey for 172.19.2.1:22
Inbound-ReKey for 172.19.2.1:22
user1@172.19.2.1's password:
sftp> *progress*
Progress meter enabled
sftp> *get /code/n9000-epld.10.4.5.M.img /bootflash/n9000-epld.10.4.5.M.img*
/code/n9000-epld.10.4.5.M.img  100%  161MB   9.5MB/s   00:16
sftp> *exit*
Copy complete, now saving to disk (please wait)...
Copy complete.

NX-OS 소프트웨어의 실행 버전을 확인하세요.

show version

예

cs2# *show version*
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (C) 2002-2020, Cisco and/or its affiliates.
All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under their own
licenses, such as open source.  This software is provided "as is," and unless
otherwise stated, there is no warranty, express or implied, including but not
limited to warranties of merchantability and fitness for a particular purpose.
Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or
GNU General Public License (GPL) version 3.0  or the GNU
Lesser General Public License (LGPL) Version 2.1 or
Lesser General Public License (LGPL) Version 2.0.
A copy of each such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://opensource.org/licenses/gpl-3.0.html and
http://www.opensource.org/licenses/lgpl-2.1.php and
http://www.gnu.org/licenses/old-licenses/library.txt.

Software
  BIOS: version 08.38
  NXOS: version 10.3(5)
  BIOS compile time:  05/29/2020
  NXOS image file is: bootflash:///nxos.10.3.5.bin
  NXOS compile time:  4/28/2020 21:00:00 [04/29/2020 02:28:31]


Hardware
  cisco Nexus9000 C9336C-FX2 Chassis
  Intel(R) Xeon(R) CPU E5-2403 v2 @ 1.80GHz with 8154432 kB of memory.
  Processor Board ID FOC20291J6K

  Device name: cs2
  bootflash:   53298520 kB
Kernel uptime is 0 day(s), 0 hour(s), 3 minute(s), 42 second(s)


Last reset at 157524 usecs after Mon Nov  2 18:32:06 2020
  Reason: Reset Requested by CLI command reload
  System version: 9.3(4)
  Service:

plugin
  Core Plugin, Ethernet Plugin

Active Package(s):


cs2#

NX-OS 이미지를 설치합니다.

이미지 파일을 설치하면 스위치를 재부팅할 때마다 이미지 파일이 로드됩니다.

install all nxos bootflash:<bin_file_name>

예

cs2# *install all nxos bootflash:nxos.10.4.5.M.bin*

Installer will perform compatibility check first. Please wait.
Installer is forced disruptive

Verifying image bootflash:/nxos.10.4.5.M.bin for boot variable "nxos".
[] 100% -- SUCCESS

Verifying image type.
[] 100% -- SUCCESS

Preparing "nxos" version info using image bootflash:/nxos.10.4.5.M.bin.
[] 100% -- SUCCESS

Preparing "bios" version info using image bootflash:/nxos.10.4.5.M.bin.
[] 100% -- SUCCESS

Performing module support checks.
[] 100% -- SUCCESS

Notifying services about system upgrade.
[] 100% -- SUCCESS


Compatibility check is done:
Module  Bootable  Impact          Install-type  Reason
------  --------  --------------- ------------  ---------
  1     yes       Disruptive      Reset         Default upgrade is not hitless


Images will be upgraded according to following table:

Module   Image    Running-Version(pri:alt)                 New-Version         Upg-Required
------- --------- ---------------------------------------- ------------------- ------------
  1      nxos     10.3(5)                                   10.4.5(M)              yes
  1      bios     v08.37(01/28/2020):v08.23(09/23/2015)    v08.38(05/29/2020)      yes


Switch will be reloaded for disruptive upgrade.

Do you want to continue with the installation (y/n)? [n] *y*

Install is in progress, please wait.

Performing runtime checks.
[] 100% -- SUCCESS

Setting boot variables.
[] 100% -- SUCCESS

Performing configuration copy.
[] 100% -- SUCCESS

Module 1: Refreshing compact flash and upgrading bios/loader/bootrom.
Warning: please do not remove or power off the module at this time.
[] 100% -- SUCCESS

Finishing the upgrade, switch will reboot in 10 seconds.

스위치가 재부팅된 후 NX-OS 소프트웨어의 새 버전을 확인하세요.

show version

예

cs2# *show version*

Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (C) 2002-2020, Cisco and/or its affiliates.
All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under their own
licenses, such as open source.  This software is provided "as is," and unless
otherwise stated, there is no warranty, express or implied, including but not
limited to warranties of merchantability and fitness for a particular purpose.
Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or
GNU General Public License (GPL) version 3.0  or the GNU
Lesser General Public License (LGPL) Version 2.1 or
Lesser General Public License (LGPL) Version 2.0.
A copy of each such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://opensource.org/licenses/gpl-3.0.html and
http://www.opensource.org/licenses/lgpl-2.1.php and
http://www.gnu.org/licenses/old-licenses/library.txt.

Software
  BIOS: version 05.33
  NXOS: version 10.4.5(M)  BIOS compile time:  09/08/2018
  NXOS image file is: bootflash:///nxos.10.4.5.M.bin
  NXOS compile time:  11/4/2018 21:00:00 [11/05/2018 06:11:06]


Hardware
  cisco Nexus9000 C9336C-FX2 Chassis
  Intel(R) Xeon(R) CPU E5-2403 v2 @ 1.80GHz with 8154432 kB of memory.
  Processor Board ID FOC20291J6K

  Device name: cs2
  bootflash:   53298520 kB
Kernel uptime is 0 day(s), 0 hour(s), 3 minute(s), 42 second(s)

Last reset at 277524 usecs after Mon Nov  2 22:45:12 2020
  Reason: Reset due to upgrade
  System version: 10.4.5(M)
  Service:

plugin
  Core Plugin, Ethernet Plugin

Active Package(s):

EPLD 이미지를 업그레이드하고 스위치를 재부팅합니다.

show version module 1 epld

install epld bootflash:<image_file_name> module all

예

cs2# *show version module 1 epld*

EPLD Device                     Version
---------------------------------------
MI   FPGA                        0x7
IO   FPGA                        0x17
MI   FPGA2                       0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2

cs2# *install epld bootflash:n9000-epld.10.4.5.M.img module all*
Compatibility check:
Module  Type      Upgradable        Impact      Reason
------  --------- ----------------- ----------- -----------
     1  SUP       Yes               disruptive  Module Upgradable

Retrieving EPLD versions.... Please wait.
Images will be upgraded according to following table:
Module  Type   EPLD              Running-Version   New-Version  Upg-Required
------- ------ ----------------- ----------------- ------------ ------------
     1  SUP    MI FPGA           0x07              0x07         No
     1  SUP    IO FPGA           0x17              0x19         Yes
     1  SUP    MI FPGA2          0x02              0x02         No
The above modules require upgrade.
The switch will be reloaded at the end of the upgrade
Do you want to continue (y/n) ?  [n] *y*

Proceeding to upgrade Modules.

Starting Module 1 EPLD Upgrade

Module 1 : IO FPGA [Programming] : 100.00% (     64 of      64 sectors)
Module 1 EPLD upgrade is successful.
Module   Type  Upgrade-Result
-------- ----- --------------
     1   SUP   Success

EPLDs upgraded.

Module 1 EPLD upgrade is successful.

스위치를 재부팅한 후 다시 로그인하여 새로운 버전의 EPLD가 성공적으로 로드되었는지 확인하세요.

show version module 1 epld

예

cs2# *show version module 1 epld*

EPLD Device                     Version
---- -------------------------- -------
MI   FPGA                        0x7
IO   FPGA                        0x19
MI   FPGA2                       0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2

10.4(5)(M) 이전 버전에서 10.5(3)(F) 이후 버전으로 업그레이드

NX-OS 소프트웨어와 EPLD 이미지를 Nexus 9336C-FX2 스위치에 복사합니다.

copy <protocol>: bootflash: vrf management

예

cs2# *copy sftp: bootflash: vrf management*
Enter source filename: */code/nxos.10.5.3.F.bin*
Enter hostname for the sftp server: *172.19.2.1*
Enter username: *user1*

Outbound-ReKey for 172.19.2.1:22
Inbound-ReKey for 172.19.2.1:22
user1@172.19.2.1's password:
sftp> *progress*
Progress meter enabled
sftp> *get /code/nxos.10.5.3.F.bin /bootflash/nxos.10.5.3.F.bin*
/code/nxos.10.5.3.F.bin  100% 1261MB   9.3MB/s   02:15
sftp> *exit*
Copy complete, now saving to disk (please wait)...
Copy complete.


cs2# *copy sftp: bootflash: vrf management*
Enter source filename: */code/n9000-epld.10.5.3.F.img*
Enter hostname for the sftp server: *172.19.2.1*
Enter username: *user1*

Outbound-ReKey for 172.19.2.1:22
Inbound-ReKey for 172.19.2.1:22
user1@172.19.2.1's password:
sftp> *progress*
Progress meter enabled
sftp> *get /code/n9000-epld.10.5.3.F.img /bootflash/n9000-epld.10.5.3.F.img*
/code/n9000-epld.10.5.3.F.img  100%  161MB   9.5MB/s   00:16
sftp> *exit*
Copy complete, now saving to disk (please wait)...
Copy complete.

NX-OS 소프트웨어의 실행 버전을 확인하세요.

show version

예

cs2# *show version*
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (C) 2002-2020, Cisco and/or its affiliates.
All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under their own
licenses, such as open source.  This software is provided "as is," and unless
otherwise stated, there is no warranty, express or implied, including but not
limited to warranties of merchantability and fitness for a particular purpose.
Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or
GNU General Public License (GPL) version 3.0  or the GNU
Lesser General Public License (LGPL) Version 2.1 or
Lesser General Public License (LGPL) Version 2.0.
A copy of each such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://opensource.org/licenses/gpl-3.0.html and
http://www.opensource.org/licenses/lgpl-2.1.php and
http://www.gnu.org/licenses/old-licenses/library.txt.

Software
  BIOS: version 08.38
  NXOS: version 10.5.3(F)
  BIOS compile time:  05/29/2020
  NXOS image file is: bootflash:///nxos.10.5.3.F.bin
  NXOS compile time:  4/28/2020 21:00:00 [04/29/2020 02:28:31]


Hardware
  cisco Nexus9000 C9336C-FX2 Chassis
  Intel(R) Xeon(R) CPU E5-2403 v2 @ 1.80GHz with 8154432 kB of memory.
  Processor Board ID FOC20291J6K

  Device name: cs2
  bootflash:   53298520 kB
Kernel uptime is 0 day(s), 0 hour(s), 3 minute(s), 42 second(s)


Last reset at 157524 usecs after Mon Nov  2 18:32:06 2020
  Reason: Reset Requested by CLI command reload
  System version: 9.3(4)
  Service:

plugin
  Core Plugin, Ethernet Plugin

Active Package(s):

cs2#

NX-OS 및 EPLD 이미지를 설치합니다.

NX-OS 10.5(3)(F) 이상으로 업그레이드할 때 EPLD 이미지는 자동으로 업데이트되지 않습니다. 업그레이드가 완료되고 스위치가 재부팅된 후에는 동일한 업그레이드 install all 명령을 다시 실행해야 합니다.

두 번째 업그레이드 단계에서는 검증만 수행하고 NX-OS 업그레이드는 건너뛰며 EPLD 이미지만 업데이트합니다.
NX-OS 10.5(3)(F) 이상으로 이미 업그레이드한 경우 두 이미지가 동시에 업데이트됩니다.

+ 이미지 파일을 설치하면 스위치를 재부팅할 때마다 이미지 파일이 로드됩니다.

+ 다음 단계는 NX-OS 10.4(5)(M)에서 10.5(3)(F)로의 업그레이드를 보여줍니다. 첫 번째 단계에서는 NX-OS 업그레이드를 수행하고 두 번째 단계에서는 EPLD 이미지 업그레이드를 수행합니다.

+ install all nxos bootflash:<nxos_image.bin>

+ .예

Details

cs2# *install all nxos bootflash:nxos.10.5.3.F.bin*   <---- 1st pass updates NX-OS only

Installer will perform compatibility check first. Please wait.
Installer is forced disruptive

Verifying image bootflash:/nxos.10.5.3.F.bin for boot variable "nxos".
[####################] 100% -- SUCCESS

Verifying image type.
[####################] 100% -- SUCCESS

Preparing "nxos" version info using image bootflash:/nxos.10.5.3.F.bin.
[####################] 100% -- SUCCESS

Preparing "bios" version info using image bootflash:/nxos.10.5.3.F.bin.
[####################] 100% -- SUCCESS

Performing module support checks.
[####################] 100% -- SUCCESS

Notifying services about system upgrade.
[####################] 100% -- SUCCESS


Compatibility check is done:
Module  Bootable  Impact          Install-type  Reason
------  --------  --------------- ------------  ---------
1       yes       Disruptive      Reset         Default upgrade is not hitless


Images will be upgraded according to following table:

Module   Image    Running-Version(pri:alt)                 New-Version          Upg-Required
------- --------- ---------------------------------------- -------------------- ------------ 
1        nxos     10.4(5)(M)                                10.5(3)(F)            yes
1        bios     v05.47(04/28/2022):v05.47(04/28/2022)    v05.53(01/22/2025)     yes

Switch will be reloaded for disruptive upgrade.

Do you want to continue with the installation (y/n)? [n] *y*

Install is in progress, please wait.

Performing runtime checks.
[####################] 100% -- SUCCESS

Setting boot variables.
[####################] 100% -- SUCCESS

Performing configuration copy.
[####################] 100% -- SUCCESS

Module 1: Refreshing compact flash and upgrading bios/loader/bootrom.
Warning: please do not remove or power off the module at this time.
[####################] 100% -- SUCCESS
[####################] 100% -- SUCCESS

Finishing the upgrade, switch will reboot in 10 seconds.


cs2# *install all nxos bootflash:nxos.10.5.3.F.bin*   <---- 2nd pass updates EPLD image only
 
Installer will perform compatibility check first. Please wait. 
Installer is forced disruptive
 
Verifying image bootflash:/nxos.10.5.3.F.bin for boot variable "nxos".
[####################] 100% -- SUCCESS
 
Verifying EPLD/FPGA image //bootflash/nxos.10.5.3.F.bin.
[####################] 100% -- SUCCESS
 
Verifying image type.
[####################] 100% -- SUCCESS
 
Preparing "nxos" version info using image bootflash:/nxos.10.5.3.F.bin.
[####################] 100% -- SUCCESS
 
Preparing "bios" version info using image bootflash:/nxos.10.5.3.F.bin.
[####################] 100% -- SUCCESS

Performing module support checks.
[####################] 100% -- SUCCESS
 
Notifying services about system upgrade.
[####################] 100% -- SUCCESS
 

Compatibility check is done:
Module  bootable  Impact          Install-type  Reason
------  --------  --------------  ------------  ------
1       yes       disruptive      reset         default upgrade is not hitless
27      yes       disruptive      none          default upgrade is not hitless
 
 
Images will be upgraded according to following table:
Module    Image                  Running-Version(pri:alt)              New-Version         Upg-Required
--------  ---------------------  ------------------------------------- -----------------  ------------
27        nxos                   10.4(5)(M)                            10.5(3)(F)             no
27        bios                   v05.53(01/22/2025):v05.47(04/28/2022) v05.53(01/22/2025)    no
 
 
FPGA microcode will be upgraded according to following table:
Module  Type  EPLD               Running-Version  Flashed-Version*   New-Version  Upg-Required
------  ----  -----------------  ---------------  ----------------   -----------  ------------
27      SUP   MI FPGA            0x5              0x5                0x5          No
27      SUP   IO FPGA            0x17             0x17               0x18         Yes

If Running-Version and Flashed-Version are different it implies that the system has not yet been reloaded for the new version to take effect.
 
EPLD Upgrade may result in multiple modules going offline.
 
 
Switch will be reloaded for disruptive upgrade.
 
Do you want to continue with the installation (y/n)?  [n] *y*
 
Install is in progress, please wait.

Setting boot variables.
[####################] 100% -- SUCCESS
 
Performing configuration copy.
[####################] 100% -- SUCCESS
Performing configuration copy.
[####################] 100% -- SUCCESS
 
Module 1: Refreshing compact flash and upgrading bios/loader/bootrom.
Warning: please do not remove or power off the module at this time.

Module 1: Refreshing compact flash and upgrading bios/loader/bootrom.
Warning: please do not remove or power off the module at this time.
[####################] 100% -- SUCCESS
 
Module 27: Refreshing compact flash and upgrading bios/loader/bootrom.
Warning: please do not remove or power off the module at this time.

Module 27: Refreshing compact flash and upgrading bios/loader/bootrom.
Warning: please do not remove or power off the module at this time.
[####################] 100% -- SUCCESS
 
EPLD/FPGA upgrade can take up to 4 mins.

Performing EPLD/FPGA upgrade.
[####################] 100% -- SUCCESS
 
Install has been successful.

스위치가 재부팅된 후 NX-OS 소프트웨어의 새 버전을 확인하세요.

show version

예

cs2# *show version*
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (C) 2002-2020, Cisco and/or its affiliates.
All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under their own
licenses, such as open source.  This software is provided "as is," and unless
otherwise stated, there is no warranty, express or implied, including but not
limited to warranties of merchantability and fitness for a particular purpose.
Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or
GNU General Public License (GPL) version 3.0  or the GNU
Lesser General Public License (LGPL) Version 2.1 or
Lesser General Public License (LGPL) Version 2.0.
A copy of each such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://opensource.org/licenses/gpl-3.0.html and
http://www.opensource.org/licenses/lgpl-2.1.php and
http://www.gnu.org/licenses/old-licenses/library.txt.

Software
  BIOS: version 05.33
  NXOS: version 10.5.3(f)
  BIOS compile time:  09/08/2018
  NXOS image file is: bootflash:///nxos.10.5.3.F.bin
  NXOS compile time:  11/4/2018 21:00:00 [11/05/2018 06:11:06]


Hardware
  cisco Nexus9000 C9336C-FX2 Chassis
  Intel(R) Xeon(R) CPU E5-2403 v2 @ 1.80GHz with 8154432 kB of memory.
  Processor Board ID FOC20291J6K

  Device name: cs2
  bootflash:   53298520 kB
Kernel uptime is 0 day(s), 0 hour(s), 3 minute(s), 42 second(s)

Last reset at 277524 usecs after Mon Nov  2 22:45:12 2020
  Reason: Reset due to upgrade
  System version: 9.3(4)
  Service:

plugin
  Core Plugin, Ethernet Plugin

Active Package(s):

스위치를 재부팅한 후 다시 로그인하여 새로운 버전의 EPLD가 성공적으로 로드되었는지 확인하세요.

show version module 1 epld

예

cs2# *show version module 1 epld*

EPLD Device                     Version
---------------------------------------
MI   FPGA                        0x7
IO   FPGA                        0x19
MI   FPGA2                       0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2
GEM  FPGA                        0x2

NX-OS 및 EPLD 이미지를 첫 번째 스위치에 복사합니다.

copy <protocol>: bootflash: vrf management

이 예제에서는 SFTP를 사용합니다.

예

cs2# *copy sftp: bootflash: vrf management*
Enter source filename: *nxos64-cs.10.5.4.M.bin*
Enter hostname for the sftp server: *172.19.2.1*
Enter username: *user1*

Outbound-ReKey for 172.19.2.1:22
Inbound-ReKey for 172.19.2.1:22
user1@172.19.2.1's password:
sftp> *progress*
Progress meter enabled
sftp> *get /code/nxos64-cs.10.5.4.M.bin /bootflash/nxos64-cs.10.5.4.M.bin*
/code/nxos64-cs.10.5.4.M.bin  100% 1261MB   9.3MB/s   02:15
sftp> *exit*
Copy complete, now saving to disk (please wait)...
Copy complete.

NX-OS의 실행 중인 버전을 확인하십시오.

show version

예

cs2# *show version*
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (C) 2002-2025, Cisco and/or its affiliates.
All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under their own
licenses, such as open source.  This software is provided "as is," and unless
otherwise stated, there is no warranty, express or implied, including but not
limited to warranties of merchantability and fitness for a particular purpose.
Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or
GNU General Public License (GPL) version 3.0  or the GNU
Lesser General Public License (LGPL) Version 2.1 or
Lesser General Public License (LGPL) Version 2.0.
A copy of each such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://opensource.org/licenses/gpl-3.0.html and
http://www.opensource.org/licenses/lgpl-2.1.php and
http://www.gnu.org/licenses/old-licenses/library.txt.


Software
  BIOS: version 01.14
  NXOS: version 10.5(3)(F) [Feature Release]
  Host NXOS: version 10.5(3)(F)
  BIOS compile time:  11/25/2024
  NXOS image file is: bootflash:///nxos.10.5.3.F.bin
  NXOS compile time:  02/27/2026 12:00:00 [03/14/2026 05:25:50]
  NXOS boot mode: LXC


Hardware
  cisco  Nexus9000 C9336C-FX2 Chassis
  Intel(R) Xeon(R) CPU D-1633N @ 2.50GHz with 32802156 kB of memory.
  Processor Board ID FLMXXXXXXXX
  Device name: cs2
  bootflash:  115802886 kB


Kernel uptime is 5 day(s), 2 hour(s), 13 minute(s), 21 second(s)


Last reset at 3580 usecs after Thu Mar 5 15:55:08 2026
  Reason: Reset Requested by CLI command reload
  System version: 10.5.3(f)
  Service:


plugin
  Core Plugin, Ethernet Plugin


Active Package(s):

cs2#

NX-OS 및 EPLD 이미지를 설치합니다.

이미지 파일을 설치하면 스위치를 재부팅할 때마다 이미지 파일이 로드됩니다.

install all nxos bootflash:<nxos_image.bin>

이 예제는 NX-OS 버전 10.5(4)(M)을 사용합니다.

예

cs2# *install all nxos bootflash:nxos64-cs.10.5.4.M.bin*

Installer will perform compatibility check first. Please wait.
Installer is forced disruptive

Verifying image bootflash:/nxos64-cs.10.5.4.M.bin for boot variable "nxos".
[####################] 100% -- SUCCESS

Verifying image type.
[####################] 100% -- SUCCESS

Preparing "nxos" version info using image bootflash:/nxos64-cs.10.5.4.M.bin.
[####################] 100% -- SUCCESS

Preparing "bios" version info using image bootflash:/nxos64-cs.10.5.4.M.bin.
[####################] 100% -- SUCCESS

Performing module support checks.
[####################] 100% -- SUCCESS

Notifying services about system upgrade.
[####################] 100% -- SUCCESS


Compatibility check is done:
Module  Bootable  Impact          Install-type  Reason
------  --------  --------------- ------------  ---------
  1     yes       Disruptive      Reset         Default upgrade is not hitless


Images will be upgraded according to following table:

Module   Image    Running-Version(pri:alt)            New-Version         Upg-Required
------- --------- ----------------------------------- ------------------- ------------
  1      nxos     10.5(3)(F)                          10.5(4)(M)          Yes
  1      bios     <current_version>                   <new_version>       No


Switch will be reloaded for disruptive upgrade.

Do you want to continue with the installation (y/n)? [n] *y*

Install is in progress, please wait.

Performing runtime checks.
[####################] 100% -- SUCCESS

Setting boot variables.
[####################] 100% -- SUCCESS

Performing configuration copy.
[####################] 100% -- SUCCESS

Module 1: Refreshing compact flash and upgrading bios/loader/bootrom.
Warning: please do not remove or power off the module at this time.
[####################] 100% -- SUCCESS

Finishing the upgrade, switch will reboot in 10 seconds.

스위치가 재부팅된 후 NX-OS의 새 버전을 확인하십시오.

show version

예

cs2# *show version*
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (C) 2002-2025, Cisco and/or its affiliates.
All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under their own
licenses, such as open source.  This software is provided "as is," and unless
otherwise stated, there is no warranty, express or implied, including but not
limited to warranties of merchantability and fitness for a particular purpose.
Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or
GNU General Public License (GPL) version 3.0  or the GNU
Lesser General Public License (LGPL) Version 2.1 or
Lesser General Public License (LGPL) Version 2.0.
A copy of each such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://opensource.org/licenses/gpl-3.0.html and
http://www.opensource.org/licenses/lgpl-2.1.php and
http://www.gnu.org/licenses/old-licenses/library.txt.


Software
  BIOS: version 01.14
  NXOS: version 10.5(4)(M) [Feature Release]
  Host NXOS: version 10.5(4)(M)
  BIOS compile time:  11/25/2024
  NXOS image file is: bootflash:///nxos64-cs.10.5.4.M.bin
  NXOS compile time:  05/30/2026 12:00:00 [06/14/2026 05:25:50]
  NXOS boot mode: LXC


Hardware
  cisco Nexus9000 C9336C-FX2 Chassis
  Intel(R) Xeon(R) CPU D-1633N @ 2.50GHz with 32802156 kB of memory.
  Processor Board ID FLMXXXXXXXX
  Device name: cs2
  bootflash:  115802886 kB


Kernel uptime is 5 day(s), 2 hour(s), 13 minute(s), 21 second(s)


Last reset at 3580 usecs after Thu Jun 5 15:55:08 2026
  Reason: Reset Requested by CLI command reload
  System version: 10.5(4)(M)
  Service:


plugin
  Core Plugin, Ethernet Plugin


Active Package(s):

새 버전의 EPLD가 성공적으로 로드되었는지 확인하십시오.

show install epld status

이 예제는 EPLD 버전 10.5(4)(M)을 사용합니다.

예

cs2# *show install epld status*

1) Module 2 upgraded on Mon May  4 09:17:08 2026 (631239  us)
EPLD Install Image: EPLD image file 10.5.4.M. built on Fri Apr 24 19:49:50 2026

Status: EPLD Upgrade was Successful

EPLD                             Curr Ver       Old Ver
-------------------------------------------------------
MI FPGA                         0x10014         0x1000b
IO FPGA                         0x10033         0x10006

2) Module 27 upgraded on Wed Apr  1 15:03:13 2026 (193093  us)
EPLD Install Image: EPLD image file 10.5.4.M. built on Mon Mar 16 03:28:47 2026

Status: EPLD Upgrade was Successful

EPLD                            Curr Ver        Old Ver
-------------------------------------------------------
IO FPGA                         0x1002d         0x10020

3) Module 28 upgraded on Wed Apr  1 14:59:53 2026 (843907  us)
EPLD Install Image: EPLD image file 10.5.4.M. built on Mon Mar 16 03:28:47 2026

Status: EPLD Upgrade was Successful

EPLD                            Curr Ver        Old Ver
-------------------------------------------------------
IO FPGA                         0x1002d         0x10020

4) Module 27 upgraded on Fri Mar 27 21:55:55 2026 (132290  us)
EPLD Install Image: EPLD image file 10.5.4.M. built on Fri Dec 12 11:15:18 2025

Status: EPLD Upgrade was Successful

EPLD                            Curr Ver        Old Ver
-------------------------------------------------------
FM-19 FPGA                      0x10006         0x10000
FM-20 FPGA                      0x10006         0x10000
FM-21 FPGA                      0x10006         0x10000
FM-22 FPGA                      0x10006         0x10000
FM-23 FPGA                      0x10006         0x10000
FM-24 FPGA                      0x10006         0x10000
FM-25 FPGA                      0x10006         0x10000
FM-26 FPGA                      0x10006         0x10000

5) Module 27 upgraded on Fri Mar 27 21:50:16 2026 (  4899  us)
EPLD Install Image: EPLD image file 10.5.4.M. built on Fri Dec 12 11:15:18 2025

Status: EPLD Upgrade was Successful

EPLD                            Curr Ver        Old Ver
-------------------------------------------------------
FM-19 FPGA                      0x10006         0x10000
FM-20 FPGA                      0x10006         0x10000
FM-21 FPGA                      0x10006         0x10000
FM-22 FPGA                      0x10006         0x10000
FM-23 FPGA                      0x10006         0x10000
FM-24 FPGA                      0x10006         0x10000
FM-25 FPGA                      0x10006         0x10000
FM-26 FPGA                      0x10006         0x10000

6) Module 27 upgraded on Fri Mar 27 21:44:36 2026 (775397  us)
EPLD Install Image: EPLD image file 10.5.4.M. built on Fri Dec 12 11:15:18 2025

Status: EPLD Upgrade was Successful

EPLD                            Curr Ver        Old Ver
-------------------------------------------------------
FM-19 FPGA                      0x10006         0x10000
FM-20 FPGA                      0x10006         0x10000
FM-21 FPGA                      0x10006         0x10000
FM-22 FPGA                      0x10006         0x10000
FM-23 FPGA                      0x10006         0x10000
FM-24 FPGA                      0x10006         0x10000
FM-25 FPGA                      0x10006         0x10000
FM-26 FPGA                      0x10006         0x10000

7) Module 27 upgraded on Fri Mar 27 21:38:58 2026 (330582  us)
EPLD Install Image: EPLD image file 10.5.4.M. built on Fri Dec 12 11:15:18 2025

Status: EPLD Upgrade was Successful

EPLD                            Curr Ver        Old Ver
-------------------------------------------------------
FM-19 FPGA                      0x10006         0x10000
FM-20 FPGA                      0x10006         0x10000
FM-21 FPGA                      0x10006         0x10000
FM-22 FPGA                      0x10006         0x10000
FM-23 FPGA                      0x10006         0x10000
FM-24 FPGA                      0x10006         0x10000
FM-25 FPGA                      0x10006         0x10000
FM-26 FPGA                      0x10006         0x10000

8) Module 27 upgraded on Fri Mar 27 21:33:19 2026 (112679  us)
EPLD Install Image: EPLD image file 10.5.4.M. built on Fri Dec 12 11:15:18 2025

Status: EPLD Upgrade was Successful

EPLD                            Curr Ver        Old Ver
-------------------------------------------------------
FM-19 FPGA                      0x10006         0x10000
FM-20 FPGA                      0x10006         0x10000
FM-21 FPGA                      0x10006         0x10000
FM-22 FPGA                      0x10006         0x10000
FM-23 FPGA                      0x10006         0x10000
FM-24 FPGA                      0x10006         0x10000
FM-25 FPGA                      0x10006         0x10000
FM-26 FPGA                      0x10006         0x10000

9) Module 27 upgraded on Fri Mar 27 21:27:41 2026 (957182  us)
EPLD Install Image: EPLD image file 10.5.4.M. built on Fri Dec 12 11:15:18 2025

Status: EPLD Upgrade was Successful

EPLD                            Curr Ver        Old Ver
-------------------------------------------------------
FM-19 FPGA                      0x10006         0x10000
FM-20 FPGA                      0x10006         0x10000
FM-21 FPGA                      0x10006         0x10000
FM-22 FPGA                      0x10006         0x10000
FM-23 FPGA                      0x10006         0x10000
FM-24 FPGA                      0x10006         0x10000
FM-25 FPGA                      0x10006         0x10000
FM-26 FPGA                      0x10006         0x10000

10) Module 27 upgraded on Fri Mar 27 21:22:03 2026 ( 90303  us)
EPLD Install Image: EPLD image file 10.5.4.M. built on Fri Dec 12 11:15:18 2025

Status: EPLD Upgrade was Successful

EPLD                            Curr Ver        Old Ver
-------------------------------------------------------
FM-19 FPGA                      0x10006         0x10000
FM-20 FPGA                      0x10006         0x10000
FM-21 FPGA                      0x10006         0x10000
FM-22 FPGA                      0x10006         0x10000
FM-23 FPGA                      0x10006         0x10000
FM-24 FPGA                      0x10006         0x10000
FM-25 FPGA                      0x10006         0x10000
FM-26 FPGA                      0x10006         0x10000

11) Module 1 upgraded on Fri Mar 27 21:16:24 2026 (240369  us)
EPLD Install Image: EPLD image file 10.5.4.M. built on Fri Dec 12 11:15:18 2025

Status: EPLD Upgrade was Successful

EPLD                            Curr Ver        Old Ver
-------------------------------------------------------
MI FPGA                         0x10014         0x1000b
IO FPGA                         0x10033         0x10006

클러스터에서 클러스터 포트의 상태를 확인합니다.

클러스터의 모든 노드에서 클러스터 포트가 작동 중이고 정상인지 확인하세요.

network port show -ipspace Cluster

예를 보여주세요

cluster1::*> network port show -ipspace Cluster

Node: cluster1-01
                                                                        Ignore
                                                  Speed(Mbps)  Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper   Status   Status
--------- ------------ ---------------- ---- ---- ------------ -------- ------
e0a       Cluster      Cluster          up   9000  auto/100000 healthy  false
e0b       Cluster      Cluster          up   9000  auto/100000 healthy  false

Node: cluster1-02
                                                                        Ignore
                                                  Speed(Mbps)  Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper   Status   Status
--------- ------------ ---------------- ---- ---- ------------ -------- ------
e0a       Cluster      Cluster          up   9000  auto/100000 healthy  false
e0b       Cluster      Cluster          up   9000  auto/100000 healthy  false

Node: cluster1-03
                                                                        Ignore
                                                  Speed(Mbps)  Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper   Status   Status
--------- ------------ ---------------- ---- ---- ------------ -------- ------
e0a       Cluster      Cluster          up   9000  auto/100000 healthy  false
e0b       Cluster      Cluster          up   9000  auto/100000 healthy  false

Node: cluster1-04
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e0a       Cluster      Cluster          up   9000  auto/100000 healthy false
e0b       Cluster      Cluster          up   9000  auto/100000 healthy false

클러스터에서 스위치 상태를 확인합니다.

network device-discovery show -protocol cdp

예를 보여주세요

cluster1::*> network device-discovery show -protocol cdp
Node/       Local  Discovered
Protocol    Port   Device (LLDP: ChassisID)  Interface         Platform
----------- ------ ------------------------- ----------------- --------------
cluster1-01/cdp
            e0a    cs1                       Ethernet1/7       N9K-C9336C-FX2
            e0b    cs2                       Ethernet1/7       N9K-C9336C-FX2
cluster01-2/cdp
            e0a    cs1                       Ethernet1/8       N9K-C9336C-FX2
            e0b    cs2                       Ethernet1/8       N9K-C9336C-FX2
cluster01-3/cdp
            e0a    cs1                       Ethernet1/1/1     N9K-C9336C-FX2
            e0b    cs2                       Ethernet1/1/1     N9K-C9336C-FX2
cluster1-04/cdp
            e0a    cs1                       Ethernet1/1/2     N9K-C9336C-FX2
            e0b    cs2                       Ethernet1/1/2     N9K-C9336C-FX2

cluster1::*> system cluster-switch show -is-monitoring-enabled-operational true
Switch                      Type               Address          Model
--------------------------- ------------------ ---------------- --------------
cs1                         cluster-network    10.233.205.90    N9K-C9336C-FX2
     Serial Number: FOCXXXXXXGD
      Is Monitored: true
            Reason: None
  Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                    9.3(5)
    Version Source: CDP

cs2                         cluster-network    10.233.205.91    N9K-C9336C-FX2
     Serial Number: FOCXXXXXXGS
      Is Monitored: true
            Reason: None
  Software Version: Cisco Nexus Operating System (NX-OS) Software, Version
                    9.3(5)
    Version Source: CDP

2 entries were displayed.

스위치에 이전에 로드된 RCF 버전에 따라 cs1 스위치 콘솔에서 다음과 같은 출력이 표시될 수 있습니다.

2020 Nov 17 16:07:18 cs1 %$ VDC-1 %$ %STP-2-UNBLOCK_CONSIST_PORT: Unblocking port port-channel1 on VLAN0092. Port consistency restored.
2020 Nov 17 16:07:23 cs1 %$ VDC-1 %$ %STP-2-BLOCK_PVID_PEER: Blocking port-channel1 on VLAN0001. Inconsistent peer vlan.
2020 Nov 17 16:07:23 cs1 %$ VDC-1 %$ %STP-2-BLOCK_PVID_LOCAL: Blocking port-channel1 on VLAN0092. Inconsistent local vlan.

클러스터가 정상인지 확인하세요.

cluster show

예를 보여주세요

cluster1::*> cluster show
Node                 Health   Eligibility   Epsilon
-------------------- -------- ------------- -------
cluster1-01          true     true          false
cluster1-02          true     true          false
cluster1-03          true     true          true
cluster1-04          true     true          false
4 entries were displayed.
cluster1::*>

6단계부터 8단계까지 반복하여 스위치 cs1에 NX-OS 소프트웨어를 설치하십시오.
클러스터 LIF에서 자동 복원 기능을 활성화하기 전에 원격 클러스터 인터페이스의 연결 상태를 확인하십시오.

ONTAP 9.9.1 이상

당신은 사용할 수 있습니다 network interface check cluster-connectivity 클러스터 연결에 대한 접근성 검사를 시작한 다음 세부 정보를 표시하는 명령:

network interface check cluster-connectivity start`그리고 `network interface check cluster-connectivity show

cluster1::*> network interface check cluster-connectivity start

참고: 실행하기 전에 몇 초 동안 기다리십시오. show 세부 정보를 표시하는 명령입니다.

cluster1::*> network interface check cluster-connectivity show
                                  Source               Destination         Packet
Node   Date                       LIF                  LIF                 Loss
------ -------------------------- -------------------- ------------------- -----------
cluster1-01
       3/5/2022 19:21:18 -06:00   cluster1-01_clus2    cluster1-02-clus1   none
       3/5/2022 19:21:20 -06:00   cluster1-01_clus2    cluster1-02_clus2   none
cluster1-02
       3/5/2022 19:21:18 -06:00   cluster1-02_clus2    cluster1-01_clus1   none
       3/5/2022 19:21:20 -06:00   cluster1-02_clus2    cluster1-01_clus2   none

모든 ONTAP 릴리스

모든 ONTAP 릴리스의 경우 다음을 사용할 수도 있습니다. cluster ping-cluster -node <name> 연결성을 확인하는 명령:

cluster ping-cluster -node <name>

cluster1::*> cluster ping-cluster -node local
Host is cluster1-02
Getting addresses from network interface table...
Cluster cluster1-01_clus1 169.254.209.69 cluster1-01     e0a
Cluster cluster1-01_clus2 169.254.49.125 cluster1-01     e0b
Cluster cluster1-02_clus1 169.254.47.194 cluster1-02     e0a
Cluster cluster1-02_clus2 169.254.19.183 cluster1-02     e0b
Local = 169.254.47.194 169.254.19.183
Remote = 169.254.209.69 169.254.49.125
Cluster Vserver Id = 4294967293
Ping status:

Basic connectivity succeeds on 4 path(s)
Basic connectivity fails on 0 path(s)

Detected 9000 byte MTU on 4 path(s):
    Local 169.254.19.183 to Remote 169.254.209.69
    Local 169.254.19.183 to Remote 169.254.49.125
    Local 169.254.47.194 to Remote 169.254.209.69
    Local 169.254.47.194 to Remote 169.254.49.125
Larger than PMTU communication succeeds on 4 path(s)
RPC status:
2 paths up, 0 paths down (tcp check)
2 paths up, 0 paths down (udp check)

클러스터 LIF에서 자동 되돌리기를 활성화합니다.

network interface modify -vserver Cluster -lif * -auto-revert true

클러스터 LIF가 홈 포트로 되돌아갔는지 확인하세요.

network interface show -vserver Cluster

예를 보여주세요

cluster1::*> network interface show -vserver Cluster
            Logical            Status     Network            Current             Current Is
Vserver     Interface          Admin/Oper Address/Mask       Node                Port    Home
----------- ------------------ ---------- ------------------ ------------------- ------- ----
Cluster
            cluster1-01_clus1  up/up      169.254.3.4/23     cluster1-01         e0b     true
            cluster1-01_clus2  up/up      169.254.3.5/23     cluster1-01         e0b     true
            cluster1-02_clus1  up/up      169.254.3.8/23     cluster1-02         e0b     true
            cluster1-02_clus2  up/up      169.254.3.9/23     cluster1-02         e0b     true
            cluster1-03_clus1  up/up      169.254.1.3/23     cluster1-03         e0b     true
            cluster1-03_clus2  up/up      169.254.1.1/23     cluster1-03         e0b     true
            cluster1-04_clus1  up/up      169.254.1.6/23     cluster1-04         e0b     true
            cluster1-04_clus2  up/up      169.254.1.7/23     cluster1-04         e0b     true
cluster1::*>

클러스터 LIF가 홈 포트로 복귀하지 않은 경우 로컬 노드에서 수동으로 되돌리십시오.

network interface revert -vserver Cluster -lif <lif_name>

다음은 무엇인가요?

NX-OS 소프트웨어를 설치 또는 업그레이드한 후 "참조 구성 파일(RCF) 설치 또는 업그레이드"할 수 있습니다.

NX-OS 소프트웨어 설치 또는 업그레이드

Creating your file...

검토 요구 사항

소프트웨어를 설치하세요