시작하십시오
본 한국어 번역은 사용자 편의를 위해 제공되는 기계 번역입니다. 영어 버전과 한국어 버전이 서로 어긋나는 경우에는 언제나 영어 버전이 우선합니다.
RCF(Reference Configuration File) 스크립트를 설치합니다
기여자
변경 제안
PDF
RCF 스크립트를 설치하려면 다음 절차를 따르십시오.
필요한 것
RCF 스크립트를 설치하기 전에 스위치에서 다음 사항을 사용할 수 있는지 확인하십시오.
-
Cumulus Linux가 설치되었습니다. 를 참조하십시오 "Hardware Universe" 를 참조하십시오.
-
IP 주소, 서브넷 마스크 및 기본 게이트웨이는 DHCP를 통해 정의되거나 수동으로 구성됩니다.
|
RCF에서 특히 로그 수집에 사용할 사용자(관리자 사용자 제외)를 지정해야 합니다. |
최신 RCF 스크립트 버전
클러스터 및 스토리지 애플리케이션에 사용 가능한 RCF 스크립트 2개가 있습니다. 에서 RCFs를 다운로드합니다 "여기". 각각의 절차는 동일합니다.
-
클러스터: * MSN2100-RCF-v1.x-Cluster-HA-Breakout-LLDP *
-
스토리지: * MSN2100-RCF-v1.x-스토리지 *
예를 참조하십시오
다음 예제 절차에서는 클러스터 스위치용 RCF 스크립트를 다운로드하고 적용하는 방법을 보여 줍니다.
명령 출력의 예는 스위치 관리 IP 주소 10.233.204.71, 넷마스크 255.255.254.0 및 기본 게이트웨이 10.233.204.1을 사용합니다.
예 1. 단계
Cumulus Linux 4.4.3
-
SN2100 스위치에 사용 가능한 인터페이스를 표시합니다.
admin@sw1:mgmt:~$ net show interface all State Name Spd MTU Mode LLDP Summary ----- ----- --- ----- ----------- ------------------ -------------- ... ... ADMDN swp1 N/A 9216 NotConfigured ADMDN swp2 N/A 9216 NotConfigured ADMDN swp3 N/A 9216 NotConfigured ADMDN swp4 N/A 9216 NotConfigured ADMDN swp5 N/A 9216 NotConfigured ADMDN swp6 N/A 9216 NotConfigured ADMDN swp7 N/A 9216 NotConfigured ADMDN swp8 N/A 9216 NotConfigured ADMDN swp9 N/A 9216 NotConfigured ADMDN swp10 N/A 9216 NotConfigured ADMDN swp11 N/A 9216 NotConfigured ADMDN swp12 N/A 9216 NotConfigured ADMDN swp13 N/A 9216 NotConfigured ADMDN swp14 N/A 9216 NotConfigured ADMDN swp15 N/A 9216 NotConfigured ADMDN swp16 N/A 9216 NotConfigured
-
RCF 비톤 스크립트를 스위치에 복사합니다.
admin@sw1:mgmt:~$ pwd /home/cumulus cumulus@cumulus:mgmt: /tmp$ scp <user>@<host:/<path>/MSN2100-RCF-v1.x-Cluster-HA-Breakout-LLDP ./ ssologin@10.233.204.71's password: MSN2100-RCF-v1.x-Cluster-HA-Breakout-LLDP 100% 8607 111.2KB/s 00:00
있습니다 scp이 예제에 사용된 경우, 선호하는 파일 전송 방법을 사용할 수 있습니다. -
RCF python 스크립트 * MSN2100-RCF-v1.x-Cluster-HA-Breakout-LLDP * 를 적용합니다.
cumulus@cumulus:mgmt:/tmp$ sudo python3 MSN2100-RCF-v1.x-Cluster-HA-Breakout-LLDP [sudo] password for cumulus: ... Step 1: Creating the banner file Step 2: Registering banner message Step 3: Updating the MOTD file Step 4: Ensuring passwordless use of cl-support command by admin Step 5: Disabling apt-get Step 6: Creating the interfaces Step 7: Adding the interface config Step 8: Disabling cdp Step 9: Adding the lldp config Step 10: Adding the RoCE base config Step 11: Modifying RoCE Config Step 12: Configure SNMP Step 13: Reboot the switch
RCF 스크립트는 위의 예에 나열된 단계를 완료합니다.
3단계 * 위의 MOTD 파일 업데이트 * 에서, 명령어 cat /etc/motd가 실행됩니다. 이를 통해 RCF 배너에서 RCF 파일 이름, RCF 버전, 사용할 포트 및 기타 중요한 정보를 확인할 수 있습니다.
수정할 수 없는 RCF 비톤 스크립트 문제에 대해서는 에 문의하십시오 "NetApp 지원" 을 참조하십시오. -
재부팅 후 구성을 확인합니다.
admin@sw1:mgmt:~$ net show interface all State Name Spd MTU Mode LLDP Summary ----- --------- ---- ----- ---------- ----------------- -------- ... ... DN swp1s0 N/A 9216 Trunk/L2 Master: bridge(UP) DN swp1s1 N/A 9216 Trunk/L2 Master: bridge(UP) DN swp1s2 N/A 9216 Trunk/L2 Master: bridge(UP) DN swp1s3 N/A 9216 Trunk/L2 Master: bridge(UP) DN swp2s0 N/A 9216 Trunk/L2 Master: bridge(UP) DN swp2s1 N/A 9216 Trunk/L2 Master: bridge(UP) DN swp2s2 N/A 9216 Trunk/L2 Master: bridge(UP) DN swp2s3 N/A 9216 Trunk/L2 Master: bridge(UP) UP swp3 100G 9216 Trunk/L2 Master: bridge(UP) UP swp4 100G 9216 Trunk/L2 Master: bridge(UP) DN swp5 N/A 9216 Trunk/L2 Master: bridge(UP) DN swp6 N/A 9216 Trunk/L2 Master: bridge(UP) DN swp7 N/A 9216 Trunk/L2 Master: bridge(UP) DN swp8 N/A 9216 Trunk/L2 Master: bridge(UP) DN swp9 N/A 9216 Trunk/L2 Master: bridge(UP) DN swp10 N/A 9216 Trunk/L2 Master: bridge(UP) DN swp11 N/A 9216 Trunk/L2 Master: bridge(UP) DN swp12 N/A 9216 Trunk/L2 Master: bridge(UP) DN swp13 N/A 9216 Trunk/L2 Master: bridge(UP) DN swp14 N/A 9216 Trunk/L2 Master: bridge(UP) UP swp15 N/A 9216 BondMember Master: bond_15_16(UP) UP swp16 N/A 9216 BondMember Master: bond_15_16(UP) ... ... admin@sw1:mgmt:~$ net show roce config RoCE mode.......... lossless Congestion Control: Enabled SPs.... 0 2 5 Mode........... ECN Min Threshold.. 150 KB Max Threshold.. 1500 KB PFC: Status......... enabled Enabled SPs.... 2 5 Interfaces......... swp10-16,swp1s0-3,swp2s0-3,swp3-9 DSCP 802.1p switch-priority ----------------------- ------ --------------- 0 1 2 3 4 5 6 7 0 0 8 9 10 11 12 13 14 15 1 1 16 17 18 19 20 21 22 23 2 2 24 25 26 27 28 29 30 31 3 3 32 33 34 35 36 37 38 39 4 4 40 41 42 43 44 45 46 47 5 5 48 49 50 51 52 53 54 55 6 6 56 57 58 59 60 61 62 63 7 7 switch-priority TC ETS --------------- -- -------- 0 1 3 4 6 7 0 DWRR 28% 2 2 DWRR 28% 5 5 DWRR 43%
-
인터페이스의 트랜시버에 대한 정보를 확인합니다.
admin@sw1:mgmt:~$ net show interface pluggables Interface Identifier Vendor Name Vendor PN Vendor SN Vendor Rev --------- ------------- ----------- --------------- -------------- ---------- swp3 0x11 (QSFP28) Amphenol 112-00574 APF20379253516 B0 swp4 0x11 (QSFP28) AVAGO 332-00440 AF1815GU05Z A0 swp15 0x11 (QSFP28) Amphenol 112-00573 APF21109348001 B0 swp16 0x11 (QSFP28) Amphenol 112-00573 APF21109347895 B0
-
각 노드가 각 스위치에 연결되어 있는지 확인합니다.
admin@sw1:mgmt:~$ net show lldp LocalPort Speed Mode RemoteHost RemotePort --------- ----- ---------- ---------------------- ----------- swp3 100G Trunk/L2 sw1 e3a swp4 100G Trunk/L2 sw2 e3b swp15 100G BondMember sw13 swp15 swp16 100G BondMember sw14 swp16
-
클러스터에서 클러스터 포트의 상태를 확인합니다.
-
e0d 포트가 클러스터의 모든 노드에서 정상 작동 중인지 확인합니다.
cluster1::*> network port show -role cluster Node: node1 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ----------- -------- ------ e3a Cluster Cluster up 9000 auto/10000 healthy false e3b Cluster Cluster up 9000 auto/10000 healthy false Node: node2 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ----------- -------- ------ e3a Cluster Cluster up 9000 auto/10000 healthy false e3b Cluster Cluster up 9000 auto/10000 healthy false -
클러스터에서 스위치 상태를 확인합니다. LIF가 e0d에 홈링되지 않으므로 스위치 SW2가 표시되지 않을 수 있습니다.
cluster1::*> network device-discovery show -protocol lldp Node/ Local Discovered Protocol Port Device (LLDP: ChassisID) Interface Platform ----------- ------ ------------------------- --------- ---------- node1/lldp e3a sw1 (b8:ce:f6:19:1a:7e) swp3 - e3b sw2 (b8:ce:f6:19:1b:96) swp3 - node2/lldp e3a sw1 (b8:ce:f6:19:1a:7e) swp4 - e3b sw2 (b8:ce:f6:19:1b:96) swp4 - cluster1::*> system switch ethernet show -is-monitoring-enabled-operational true Switch Type Address Model --------------------------- ------------------ ---------------- ----- sw1 cluster-network 10.233.205.90 MSN2100-CB2RC Serial Number: MNXXXXXXGD Is Monitored: true Reason: None Software Version: Cumulus Linux version 4.4.3 running on Mellanox Technologies Ltd. MSN2100 Version Source: LLDP sw2 cluster-network 10.233.205.91 MSN2100-CB2RC Serial Number: MNCXXXXXXGS Is Monitored: true Reason: None Software Version: Cumulus Linux version 4.4.3 running on Mellanox Technologies Ltd. MSN2100 Version Source: LLDP
-
Cumulus Linux 5.x를 의미합니다
-
SN2100 스위치에 사용 가능한 인터페이스를 표시합니다.
admin@sw1:mgmt:~$ nv show interface Interface MTU Speed State Remote Host Remote Port- Type Summary ------------- ----- ----- ----- ------------------- ------------ --------- ------------- + cluster_isl 9216 200G up bond + eth0 1500 100M up mgmt-sw1 Eth105/1/14 eth IP Address: 10.231.80 206/22 eth0 IP Address: fd20:8b1e:f6ff:fe31:4a0e/64 + lo 65536 up loopback IP Address: 127.0.0.1/8 lo IP Address: ::1/128 + swp1s0 9216 10G up cluster01 e0b swp . . . + swp15 9216 100G up sw2 swp15 swp + swp16 9216 100G up sw2 swp16 swp
-
RCF 비톤 스크립트를 스위치에 복사합니다.
admin@sw1:mgmt:~$ pwd /home/cumulus cumulus@cumulus:mgmt: /tmp$ scp <user>@<host:/<path>/MSN2100-RCF-v1.x-Cluster-HA-Breakout-LLDP ./ ssologin@10.233.204.71's password: MSN2100-RCF-v1.x-Cluster-HA-Breakout-LLDP 100% 8607 111.2KB/s 00:00
있습니다 scp이 예제에 사용된 경우, 선호하는 파일 전송 방법을 사용할 수 있습니다. -
RCF python 스크립트 * MSN2100-RCF-v1.x-Cluster-HA-Breakout-LLDP * 를 적용합니다.
cumulus@cumulus:mgmt:/tmp$ sudo python3 MSN2100-RCF-v1.x-Cluster-HA-Breakout-LLDP [sudo] password for cumulus: . . Step 1: Creating the banner file Step 2: Registering banner message Step 3: Updating the MOTD file Step 4: Ensuring passwordless use of cl-support command by admin Step 5: Disabling apt-get Step 6: Creating the interfaces Step 7: Adding the interface config Step 8: Disabling cdp Step 9: Adding the lldp config Step 10: Adding the RoCE base config Step 11: Modifying RoCE Config Step 12: Configure SNMP Step 13: Reboot the switch
RCF 스크립트는 위의 예에 나열된 단계를 완료합니다.
3단계 * 위의 MOTD 파일 업데이트 * 에서, 명령어 cat /etc/issue가 실행됩니다. 이를 통해 RCF 배너에서 RCF 파일 이름, RCF 버전, 사용할 포트 및 기타 중요한 정보를 확인할 수 있습니다.예를 들면 다음과 같습니다.
admin@sw1:mgmt:~$ cat /etc/issue ****************************************************************************** * * NetApp Reference Configuration File (RCF) * Switch : Mellanox MSN2100 * Filename : MSN2100-RCF-1.x-Cluster-HA-Breakout-LLDP * Release Date : 13-02-2023 * Version : 1.x-Cluster-HA-Breakout-LLDP * * Port Usage: * Port 1 : 4x10G Breakout mode for Cluster+HA Ports, swp1s0-3 * Port 2 : 4x25G Breakout mode for Cluster+HA Ports, swp2s0-3 * Ports 3-14 : 40/100G for Cluster+HA Ports, swp3-14 * Ports 15-16 : 100G Cluster ISL Ports, swp15-16 * * NOTE: * RCF manually sets swp1s0-3 link speed to 10000 and * auto-negotiation to off for Intel 10G * RCF manually sets swp2s0-3 link speed to 25000 and * auto-negotiation to off for Chelsio 25G * * * IMPORTANT: Perform the following steps to ensure proper RCF installation: * - Copy the RCF file to /tmp * - Ensure the file has execute permission * - From /tmp run the file as sudo python3 <filename> * ******************************************************************************
수정할 수 없는 RCF 비톤 스크립트 문제에 대해서는 에 문의하십시오 "NetApp 지원" 을 참조하십시오. -
재부팅 후 구성을 확인합니다.
admin@sw1:mgmt:~$ nv show interface Interface MTU Speed State Remote Host Remote Port Type Summary ----------- ----- ----- ----- ----------- ----------- ---- ------------- + cluster_isl 9216 200G up bond + eth0 1500 100M up RTP-LF01-410G38.rtp.eng.netapp.com Eth105/1/14 eth IP Address: 10.231.80.206/22 eth0 IP Address: fd20:8b1e:b255:85a0:bace:f6ff:fe31:4a0e/64 + lo 65536 up loopback IP Address: 127.0.0.1/8 lo IP Address: ::1/128 + swp1s0 9216 10G up cumulus1 e0b swp . . . + swp15 9216 100G up cumulus swp15 swp admin@sw1:mgmt:~$ nv show interface Interface MTU Speed State Remote Host Remote Port- Type Summary ------------- ----- ----- ----- ------------------- ------------ --------- ------------- + cluster_isl 9216 200G up bond + eth0 1500 100M up mgmt-sw1 Eth105/1/14 eth IP Address: 10.231.80 206/22 eth0 IP Address: fd20:8b1e:f6ff:fe31:4a0e/64 + lo 65536 up loopback IP Address: 127.0.0.1/8 lo IP Address: ::1/128 + swp1s0 9216 10G up cluster01 e0b swp . . . + swp15 9216 100G up sw2 swp15 swp + swp16 9216 100G up sw2 swp16 swp admin@sw1:mgmt:~$ nv show qos roce operational applied description ----------------- ----------- --------- ---------------------------------------- enable on Turn feature 'on' or 'off'. This feature is disabled by default. mode lossless lossless Roce Mode congestion-control congestion-mode ECN,RED Congestion config mode enabled-tc 0,2,5 Congestion config enabled Traffic Class max-threshold 195.31 KB Congestion config max-threshold min-threshold 39.06 KB Congestion config min-threshold probability 100 lldp-app-tlv priority 3 switch-priority of roce protocol-id 4791 L4 port number selector UDP L4 protocol pfc pfc-priority 2, 5 switch-prio on which PFC is enabled rx-enabled enabled PFC Rx Enabled status tx-enabled enabled PFC Tx Enabled status trust trust-mode pcp,dscp Trust Setting on the port for packet classification RoCE PCP/DSCP->SP mapping configurations =========================================== pcp dscp switch-prio -- --- ----------------------- ----------- 0 0 0,1,2,3,4,5,6,7 0 1 1 8,9,10,11,12,13,14,15 1 2 2 16,17,18,19,20,21,22,23 2 3 3 24,25,26,27,28,29,30,31 3 4 4 32,33,34,35,36,37,38,39 4 5 5 40,41,42,43,44,45,46,47 5 6 6 48,49,50,51,52,53,54,55 6 7 7 56,57,58,59,60,61,62,63 7 RoCE SP->TC mapping and ETS configurations ============================================= switch-prio traffic-class scheduler-weight -- ----------- ------------- ---------------- 0 0 0 DWRR-28% 1 1 0 DWRR-28% 2 2 2 DWRR-28% 3 3 0 DWRR-28% 4 4 0 DWRR-28% 5 5 5 DWRR-43% 6 6 0 DWRR-28% 7 7 0 DWRR-28% RoCE pool config =================== name mode size switch-priorities traffic-class -- --------------------- ------- ---- ----------------- ------------- 0 lossy-default-ingress Dynamic 50% 0,1,3,4,6,7 - 1 roce-reserved-ingress Dynamic 50% 2,5 - 2 lossy-default-egress Dynamic 50% - 0 3 roce-reserved-egress Dynamic inf - 2,5 Exception List ================= description -- -----------------------------------------------------------------------… 1 RoCE PFC Priority Mismatch.Expected pfc-priority: 3. 2 Congestion Config TC Mismatch.Expected enabled-tc: 0,3. 3 Congestion Config mode Mismatch.Expected congestion-mode: ECN. 4 Congestion Config min-threshold Mismatch.Expected min-threshold: 150000. 5 Congestion Config max-threshold Mismatch.Expected max-threshold: 1500000. 6 Scheduler config mismatch for traffic-class mapped to switch-prio0. Expected scheduler-weight: DWRR-50%. 7 Scheduler config mismatch for traffic-class mapped to switch-prio1. Expected scheduler-weight: DWRR-50%. 8 Scheduler config mismatch for traffic-class mapped to switch-prio2. Expected scheduler-weight: DWRR-50%. 9 Scheduler config mismatch for traffic-class mapped to switch-prio3. Expected scheduler-weight: DWRR-50%. 10 Scheduler config mismatch for traffic-class mapped to switch-prio4. Expected scheduler-weight: DWRR-50%. 11 Scheduler config mismatch for traffic-class mapped to switch-prio5. Expected scheduler-weight: DWRR-50%. 12 Scheduler config mismatch for traffic-class mapped to switch-prio6. Expected scheduler-weight: strict-priority. 13 Scheduler config mismatch for traffic-class mapped to switch-prio7. Expected scheduler-weight: DWRR-50%. 14 Invalid reserved config for ePort.TC[2].Expected 0 Got 1024 15 Invalid reserved config for ePort.TC[5].Expected 0 Got 1024 16 Invalid traffic-class mapping for switch-priority 2.Expected 0 Got 2 17 Invalid traffic-class mapping for switch-priority 3.Expected 3 Got 0 18 Invalid traffic-class mapping for switch-priority 5.Expected 0 Got 5 19 Invalid traffic-class mapping for switch-priority 6.Expected 6 Got 0 Incomplete Command: set interface swp3-16 link fast-linkupp3-16 link fast-linkup Incomplete Command: set interface swp3-16 link fast-linkupp3-16 link fast-linkup Incomplete Command: set interface swp3-16 link fast-linkupp3-16 link fast-linkup
나열된 예외는 성능에 영향을 주지 않으므로 무시해도 됩니다. -
인터페이스의 트랜시버에 대한 정보를 확인합니다.
admin@sw1:mgmt:~$ nv show interface --view=pluggables Interface Identifier Vendor Name Vendor PN Vendor SN Vendor Rev --------- ------------- ----------- --------------- -------------- ---------- swp1s0 0x00 None swp1s1 0x00 None swp1s2 0x00 None swp1s3 0x00 None swp2s0 0x11 (QSFP28) CISCO-LEONI L45593-D278-D20 LCC2321GTTJ 00 swp2s1 0x11 (QSFP28) CISCO-LEONI L45593-D278-D20 LCC2321GTTJ 00 swp2s2 0x11 (QSFP28) CISCO-LEONI L45593-D278-D20 LCC2321GTTJ 00 swp2s3 0x11 (QSFP28) CISCO-LEONI L45593-D278-D20 LCC2321GTTJ 00 swp3 0x00 None swp4 0x00 None swp5 0x00 None swp6 0x00 None . . . swp15 0x11 (QSFP28) Amphenol 112-00595 APF20279210117 B0 swp16 0x11 (QSFP28) Amphenol 112-00595 APF20279210166 B0
-
각 노드가 각 스위치에 연결되어 있는지 확인합니다.
admin@sw1:mgmt:~$ nv show interface --view=lldp LocalPort Speed Mode RemoteHost RemotePort --------- ----- ---------- ----------------------- ----------- eth0 100M Mgmt mgmt-sw1 Eth110/1/29 swp2s1 25G Trunk/L2 node1 e0a swp15 100G BondMember sw2 swp15 swp16 100G BondMember sw2 swp16
-
클러스터에서 클러스터 포트의 상태를 확인합니다.
-
e0d 포트가 클러스터의 모든 노드에서 정상 작동 중인지 확인합니다.
cluster1::*> network port show -role cluster Node: node1 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ----------- -------- ------ e3a Cluster Cluster up 9000 auto/10000 healthy false e3b Cluster Cluster up 9000 auto/10000 healthy false Node: node2 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ----------- -------- ------ e3a Cluster Cluster up 9000 auto/10000 healthy false e3b Cluster Cluster up 9000 auto/10000 healthy false -
클러스터에서 스위치 상태를 확인합니다. LIF가 e0d에 홈링되지 않으므로 스위치 SW2가 표시되지 않을 수 있습니다.
cluster1::*> network device-discovery show -protocol lldp Node/ Local Discovered Protocol Port Device (LLDP: ChassisID) Interface Platform ----------- ------ ------------------------- --------- ---------- node1/lldp e3a sw1 (b8:ce:f6:19:1a:7e) swp3 - e3b sw2 (b8:ce:f6:19:1b:96) swp3 - node2/lldp e3a sw1 (b8:ce:f6:19:1a:7e) swp4 - e3b sw2 (b8:ce:f6:19:1b:96) swp4 - cluster1::*> system switch ethernet show -is-monitoring-enabled-operational true Switch Type Address Model --------------------------- ------------------ ---------------- ----- sw1 cluster-network 10.233.205.90 MSN2100-CB2RC Serial Number: MNXXXXXXGD Is Monitored: true Reason: None Software Version: Cumulus Linux version 5.4.0 running on Mellanox Technologies Ltd. MSN2100 Version Source: LLDP sw2 cluster-network 10.233.205.91 MSN2100-CB2RC Serial Number: MNCXXXXXXGS Is Monitored: true Reason: None Software Version: Cumulus Linux version 5.4.0 running on Mellanox Technologies Ltd. MSN2100 Version Source: LLDP
-
다음 단계