CN1610 클러스터 스위치를 BES-53248 클러스터 스위치로 마이그레이션하는 방법
기여자
클러스터의 기존 CN1610 클러스터 스위치를 Broadcom 지원 BES-53248 클러스터 스위치로 교체하려면 특정 작업 시퀀스를 수행해야 합니다.
이 절차의 예에서는 각각 10GbE 클러스터 인터커넥트 포트 2개('e0a' 및 'e0b')를 구축하는 2개의 노드를 사용합니다.
이 절차의 예에서는 다음 스위치 및 노드 명명법을 사용합니다.
-
명령 출력은 ONTAP 소프트웨어의 릴리스에 따라 다를 수 있습니다.
-
교체할 CN1610 스위치는 CL1 CL2입니다.
-
CN1610 스위치를 교체하기 위한 BES-53248 스위치는 CS1, CS2입니다.
-
노드는 노드1, 노드2.
-
스위치 CL2는 먼저 CS2로 대체되고 그 다음에는 CL1이 CS1로 대체됩니다.
-
BES-53248 스위치는 포트 55 및 56에 연결된 ISL 케이블을 통해 지원되는 버전의 RCF(Reference Configuration File) 및 EFOS(Ethernet Fabric OS)가 미리 로드되어 있습니다.
-
클러스터 LIF 이름은 node1의 node1_clus1 및 node1_clus2, node2의 node2_clus1 및 node2_clus2 입니다.
이 절차에서는 다음 시나리오에 대해 설명합니다.
-
클러스터가 두 CN1610 클러스터 스위치에 연결된 두 노드로 시작됩니다.
-
CN1610 스위치 CL2가 BES-53248 스위치 CS2로 교체됩니다.
-
CL2에 연결된 모든 노드의 모든 클러스터 포트에서 케이블을 분리한 다음 지원되는 케이블을 사용하여 포트를 새 클러스터 스위치 CS2에 다시 연결합니다.
-
ISL 포트 CL1과 CL2 사이의 케이블을 분리한 다음 지원되는 케이블을 사용하여 CL1에서 CS2로 포트를 다시 연결합니다.
-
-
CN1610 스위치 CL1이 BES-53248 스위치 CS1로 교체됩니다.
-
CL1에 연결된 모든 노드의 모든 클러스터 포트에서 케이블을 분리한 다음 지원되는 케이블을 사용하여 포트를 새 클러스터 스위치 CS1에 다시 연결합니다.
-
ISL 포트 CL1과 CS2 사이의 케이블을 분리한 다음 지원되는 케이블을 사용하여 CS1에서 CS2로 포트를 다시 연결합니다.
-
-
이 클러스터에서 AutoSupport가 활성화되어 있는 경우 AutoSupport 메시지를 호출하여 자동 케이스 생성을 억제합니다.
'System node AutoSupport invoke-node * -type all-message maINT=xh'
여기서 x는 유지 보수 기간(시간)입니다.
AutoSupport 메시지는 유지보수 기간 동안 자동 케이스 생성이 억제되도록 이 유지보수 작업의 기술 지원에 알립니다. 다음 명령을 실행하면 2시간 동안 자동 케이스가 생성되지 않습니다.
cluster1::*> system node autosupport invoke -node \* -type all -message MAINT=2h
-
권한 수준을 고급으로 변경하고 계속할 것인지 묻는 메시지가 표시되면 * y * 를 입력합니다.
세트 프리빌리지 고급
고급 프롬프트(*>)가 나타납니다.
-
모든 클러스터 LIF에서 자동 복구가 설정되었는지 확인합니다.
'network interface show-vserver Cluster-fields auto-revert'
cluster1::*> network interface show -vserver Cluster -fields auto-revert Logical Vserver Interface Auto-revert --------- ------------- ------------ Cluster node1_clus1 true node1_clus2 true node2_clus1 true node2_clus2 true
-
구성에 있는 장치에 대한 정보를 표시합니다.
네트워크 디바이스 검색 표시 프로토콜 CDP
다음 예는 각 클러스터 인터커넥트 스위치에 대해 각 노드에 구성된 클러스터 인터커넥트 인터페이스 수를 표시합니다.
cluster1::*> network device-discovery show -protocol cdp Node/ Local Discovered Protocol Port Device (LLDP: ChassisID) Interface Platform ----------- ------ ------------------------- ---------------- ---------------- node2 /cdp e0a CL2 0/2 CN1610 e0b CL1 0/2 CN1610 node1 /cdp e0a CL2 0/1 CN1610 e0b CL1 0/1 CN1610
-
각 클러스터 인터페이스의 관리 또는 운영 상태를 확인합니다.
-
클러스터 네트워크 포트 속성을 표시합니다.
네트워크 포트 표시 - IPSpace 클러스터
cluster1::*> network port show -ipspace Cluster Node: node1 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ----------- -------- ------ e0a Cluster Cluster up 9000 auto/10000 healthy false e0b Cluster Cluster up 9000 auto/10000 healthy false Node: node2 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ----------- -------- ------ e0a Cluster Cluster up 9000 auto/10000 healthy false e0b Cluster Cluster up 9000 auto/10000 healthy false
-
논리 인터페이스에 대한 정보를 표시합니다.
'network interface show-vserver cluster'
cluster1::*> network interface show -vserver Cluster Logical Status Network Current Current Is Vserver Interface Admin/Oper Address/Mask Node Port Home ----------- ---------- ---------- ------------------ ------------- ------- ---- Cluster node1_clus1 up/up 169.254.209.69/16 node1 e0a true node1_clus2 up/up 169.254.49.125/16 node1 e0b true node2_clus1 up/up 169.254.47.194/16 node2 e0a true node2_clus2 up/up 169.254.19.183/16 node2 e0b true
-
-
필요에 따라 새 BES-53248 스위치에 적절한 포트 라이센스, RCF 및 EFOS 이미지가 설치되어 있는지 확인하고 사용자 및 암호, 네트워크 주소 등과 같은 필수 사이트 사용자 지정을 수행합니다.
-
원격 클러스터 인터페이스에 대해 ping을 수행합니다.
'cluster ping-cluster-node-name’입니다
다음 예는 원격 클러스터 인터페이스를 ping하는 방법을 보여줍니다.
cluster1::*> cluster ping-cluster -node node2 Host is node2 Getting addresses from network interface table... Cluster node1_clus1 169.254.209.69 node1 e0a Cluster node1_clus2 169.254.49.125 node1 e0b Cluster node2_clus1 169.254.47.194 node2 e0a Cluster node2_clus2 169.254.19.183 node2 e0b Local = 169.254.47.194 169.254.19.183 Remote = 169.254.209.69 169.254.49.125 Cluster Vserver Id = 4294967293 Ping status: Basic connectivity succeeds on 4 path(s) Basic connectivity fails on 0 path(s) Detected 9000 byte MTU on 4 path(s): Local 169.254.47.194 to Remote 169.254.209.69 Local 169.254.47.194 to Remote 169.254.49.125 Local 169.254.19.183 to Remote 169.254.209.69 Local 169.254.19.183 to Remote 169.254.49.125 Larger than PMTU communication succeeds on 4 path(s) RPC status: 2 paths up, 0 paths down (tcp check) 2 paths up, 0 paths down (udp check)
-
활성 CN1610 스위치 CL1에서 ISL 포트 13~16을 종료합니다.
'허틀다운'
다음 예에서는 CN1610 스위치 CL1에서 ISL 포트 13~16을 종료하는 방법을 보여 줍니다.
(CL1)# configure (CL1)(Config)# interface 0/13-0/16 (CL1)(Interface 0/13-0/16)# shutdown (CL1)(Interface 0/13-0/16)# exit (CL1)(Config)# exit (CL1)#
-
CN1610 CL1과 새 BES-53248 CS2 간에 임시 ISL을 구축합니다. ISL은 CL1의 기존 ISL을 재사용할 수 있으므로 CS2에만 정의됩니다.
다음 예에서는 CL1(포트 13-16)의 기존 ISL에 연결할 CS2(포트 13-16)에 임시 ISL을 구축합니다.
(cs2)# configure (cs2) (Config)# port-channel name 1/2 temp-isl-cn1610 (cs2) (Config)# interface 0/13-0/16 (cs2) (Interface 0/13-0/16)# no spanning-tree edgeport (cs2) (Interface 0/13-0/16)# addport 1/2 (cs2) (Interface 0/13-0/16)# exit (cs2) (Config)# interface lag 2 (cs2) (Interface lag 2)# mtu 9216 (cs2) (Interface lag 2)# port-channel load-balance 7 (cs2) (Config)# exit (cs2)# show port-channel 1/2 Local Interface................................ 1/2 Channel Name................................... temp-isl-cn1610 Link State..................................... Down Admin Mode..................................... Enabled Type........................................... Static Port-channel Min-links......................... 1 Load Balance Option............................ 7 (Enhanced hashing mode) Mbr Device/ Port Port Ports Timeout Speed Active ------- -------------- --------- ------- 0/13 actor/long 10G Full False partner/long 0/14 actor/long 10G Full False partner/long 0/15 actor/long 10G Full False partner/long 0/16 actor/long 10G Full False partner/long
-
모든 노드에서 CN1610 스위치 CL2에 연결된 케이블을 제거합니다.
그런 다음 모든 노드의 분리된 포트를 새 BES-53248 스위치 CS2에 다시 연결해야 합니다. 을 참조하십시오 "_NetApp Hardware Universe _" 승인된 케이블링 옵션에 관한 것입니다.
-
CN1610 스위치 CL2의 포트 13 - 16에서 ISL 케이블 4개를 분리합니다.
새 BES-53248 스위치 CS2의 포트 0/13-0/16 연결 승인된 케이블을 기존 CN1610 스위치 CL1의 포트 13-16에 연결해야 합니다.
-
활성 CN1610 스위치 CL1에서 ISL 13 ~ 16을 실행합니다.
다음 예에서는 CL1에서 ISL 포트 13 - 16을 가져오는 프로세스를 보여 줍니다.
(CL1)# configure (CL1)(Config)# interface 0/13-0/16 (CL1)(Interface 0/13-0/16,3/1)# no shutdown (CL1)(Interface 0/13-0/16,3/1)# exit (CL1)(Config)# exit (CL1)#
-
CN1610 스위치 CL1에서 ISL이 * UP * 인지 확인합니다.
항로를 선택합니다
Link State는 Up, Type은 Tetic, Port Active는 True여야 하며, Port Active는 0/13 ~ 0/16 포트의 경우 True여야 합니다.
(CL2)# show port-channel 3/1 Local Interface................................ 3/1 Channel Name................................... ISL-LAG Link State..................................... Up Admin Mode..................................... Enabled Type........................................... Static Load Balance Option............................ 7 (Enhanced hashing mode) Mbr Device/ Port Port Ports Timeout Speed Active -------- -------------- ----------- -------- 0/13 actor/long 10 Gb Full True partner/long 0/14 actor/long 10 Gb Full True partner/long 0/15 actor/long 10 Gb Full True partner/long 0/16 actor/long 10 Gb Full True partner/long
-
BES-53248 스위치에서 ISL 포트가 작동하는지 확인합니다.
항로를 선택합니다
(cs2)# show port-channel 1/2 Local Interface................................ 1/2 Channel Name................................... temp-isl-cn1610 Link State..................................... Up Admin Mode..................................... Enabled Type........................................... Static Port-channel Min-links......................... 1 Load Balance Option............................ 7 (Src/Dest MAC, VLAN, EType, incoming port) Mbr Device/ Port Port Ports Timeout Speed Active ------- ------------- --------- ------- 0/13 actor/long 10G Full True partner/long 0/14 actor/long 10G Full True partner/long 0/15 actor/long 10G Full True partner/long 0/16 actor/long 10G Full True partner/long
-
모든 클러스터 인터커넥트 포트가 홈 포트로 되돌려졌는지 확인합니다.
'network interface show-vserver cluster'
cluster1::*> network interface show -vserver Cluster Logical Status Network Current Current Is Vserver Interface Admin/Oper Address/Mask Node Port Home ----------- ------------ ---------- ------------------ ------------- ------- ---- Cluster node1_clus1 up/up 169.254.209.69/16 node1 e0a true node1_clus2 up/up 169.254.49.125/16 node1 e0b true node2_clus1 up/up 169.254.47.194/16 node2 e0a true node2_clus2 up/up 169.254.19.183/16 node2 e0b true
-
모든 클러스터 포트가 연결되어 있는지 확인합니다.
네트워크 포트 표시 - IPSpace 클러스터
다음 예에서는 이전 명령의 결과를 확인하여 모든 클러스터 인터커넥트가 작동하는지 확인합니다.
cluster1::*> network port show -ipspace Cluster Node: node1 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ----------- -------- ------ e0a Cluster Cluster up 9000 auto/10000 healthy false e0b Cluster Cluster up 9000 auto/10000 healthy false Node: node2 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ----------- -------- ------ e0a Cluster Cluster up 9000 auto/10000 healthy false e0b Cluster Cluster up 9000 auto/10000 healthy false
-
원격 클러스터 인터페이스에 대해 ping을 수행합니다.
'cluster ping-cluster-node_node-name_'
다음 예는 원격 클러스터 인터페이스를 ping하는 방법을 보여줍니다.
cluster1::*> cluster ping-cluster -node node2 Host is node2 Getting addresses from network interface table... Cluster node1_clus1 169.254.209.69 node1 e0a Cluster node1_clus2 169.254.49.125 node1 e0b Cluster node2_clus1 169.254.47.194 node2 e0a Cluster node2_clus2 169.254.19.183 node2 eob Local = 169.254.47.194 169.254.19.183 Remote = 169.254.209.69 169.254.49.125 Cluster Vserver Id = 4294967293 Ping status: .... Basic connectivity succeeds on 4 path(s) Basic connectivity fails on 0 path(s) ................ Detected 9000 byte MTU on 4 path(s): Local 169.254.47.194 to Remote 169.254.209.69 Local 169.254.47.194 to Remote 169.254.49.125 Local 169.254.19.183 to Remote 169.254.209.69 Local 169.254.19.183 to Remote 169.254.49.125 Larger than PMTU communication succeeds on 4 path(s) RPC status: 2 paths up, 0 paths down (tcp check) 2 paths up, 0 paths down (udp check)
-
모든 노드에서 CN1610 스위치 CL1에 연결된 케이블을 제거합니다.
그런 다음 모든 노드의 분리된 포트를 새 BES-53248 스위치 CS1에 다시 연결해야 합니다. 을 참조하십시오 "_NetApp Hardware Universe _" 승인된 케이블링 옵션에 관한 것입니다.
-
BES-53248 스위치 CS2의 포트 13에서 16까지 ISL 케이블 4개를 분리합니다.
-
CS2에서 임시 포트-채널 2를 분리합니다.
다음 예에서는 port-channel 2를 제거하고 running-configuration 파일을 startup-configuration 파일에 복사합니다.
(cs2)# configure (cs2) (Config)# deleteport 1/2 all (cs2) (Config)# interface 0/13-0/16 (cs2) (Interface 0/13-0/16)# spanning-tree edgeport (cs2) (Interface 0/13-0/16)# exit (cs2) (Config)# exit (cs2)# write memory This operation may take a few minutes. Management interfaces will not be available during this time. Are you sure you want to save? (y/n) y Config file 'startup-config' created successfully .
-
클러스터 노드 포트의 상태를 확인합니다.
네트워크 포트 표시 - IPSpace 클러스터
다음 예제에서는 node1과 node2의 모든 클러스터 상호 연결 포트가 "작동"되었는지 확인합니다.
cluster1::*> network port show -ipspace Cluster Node: node1 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ----------- -------- ------ e0a Cluster Cluster up 9000 auto/10000 healthy false e0b Cluster Cluster up 9000 auto/10000 healthy false Node: node2 Ignore Speed(Mbps) Health Health Port IPspace Broadcast Domain Link MTU Admin/Oper Status Status --------- ------------ ---------------- ---- ---- ----------- -------- ------ e0a Cluster Cluster up 9000 auto/10000 healthy false e0b Cluster Cluster up 9000 auto/10000 healthy false
-
인터페이스가 현재 홈 인터페이스인지 확인합니다.
'network interface show-vserver cluster'
다음 예에서는 node1과 node2에 대한 클러스터 인터커넥트 인터페이스의 상태가 Up 이고 is home인 것을 보여 줍니다.
cluster1::*> network interface show -vserver Cluster Logical Status Network Current Current Is Vserver Interface Admin/Oper Address/Mask Node Port Home ----------- ------------ ---------- ------------------ --------- ------- ------ Cluster node1_clus1 up/up 169.254.209.69/16 node1 e0a true node1_clus2 up/up 169.254.49.125/16 node1 e0b true node2_clus1 up/up 169.254.47.194/16 node2 e0a true node2_clus2 up/up 169.254.19.183/16 node2 e0b true
-
원격 클러스터 인터페이스에 대해 ping을 수행한 다음 원격 프로시저 호출 서버 검사를 수행합니다.
'cluster ping-cluster-node_node-name_'
다음 예는 원격 클러스터 인터페이스를 ping하는 방법을 보여줍니다.
cluster1::*> cluster ping-cluster -node node2 Host is node2 Getting addresses from network interface table... Cluster node1_clus1 169.254.209.69 node1 e0a Cluster node1_clus2 169.254.49.125 node1 e0b Cluster node2_clus1 169.254.47.194 node2 e0a Cluster node2_clus2 169.254.19.183 node2 e0b Local = 169.254.47.194 169.254.19.183 Remote = 169.254.209.69 169.254.49.125 Cluster Vserver Id = 4294967293 Ping status: Basic connectivity succeeds on 4 path(s) Basic connectivity fails on 0 path(s) ................ Detected 9000 byte MTU on 4 path(s): Local 169.254.47.194 to Remote 169.254.209.69 Local 169.254.47.194 to Remote 169.254.49.125 Local 169.254.19.183 to Remote 169.254.209.69 Local 169.254.19.183 to Remote 169.254.49.125 Larger than PMTU communication succeeds on 4 path(s) RPC status: 2 paths up, 0 paths down (tcp check) 2 paths up, 0 paths down (udp check)
-
구성에 있는 장치에 대한 정보를 표시합니다.
네트워크 디바이스 검색 표시 프로토콜 CDP
다음 예에서는 노드 1과 노드 2가 CN1610 CL2 및 CL1에서 BES-53248 CS2 및 CS1로 마이그레이션되었음을 보여 줍니다.
cluster1::*> network device-discovery show -protocol cdp Node/ Local Discovered Protocol Port Device (LLDP: ChassisID) Interface Platform ----------- ------ ------------------------- ---------------- ---------------- node1 /cdp e0a cs2 0/1 BES-53248 e0b cs1 0/1 BES-53248 node2 /cdp e0a cs2 0/2 BES-53248 e0b cs1 0/2 BES-53248
-
교체된 CN1610 스위치가 자동으로 제거되지 않은 경우 제거합니다.
'system cluster-switch delete-device_device-name_'
다음 예에서는 CN1610 스위치를 제거하는 방법을 보여 줍니다.
cluster::*> system cluster-switch delete –device CL2 cluster::*> system cluster-switch delete –device CL1
-
자동 케이스 생성을 억제한 경우 AutoSupport 메시지를 호출하여 다시 활성화합니다.
'System node AutoSupport invoke-node * -type all-message maINT=end'
cluster::*> system node autosupport invoke -node \ -type all -message MAINT=END*
을 참조하십시오 "CSHM(Cluster Switch Health Monitor) 구성 파일을 설치합니다" 및 "클러스터 스위치 로그 수집 기능을 구성합니다" 스위치 관련 로그 파일을 수집하는 데 사용되는 클러스터 상태 스위치 로그 수집을 활성화하는 데 필요한 단계를 확인합니다.
-
관련 정보 *