Skip to main content
Cluster and storage switches
본 한국어 번역은 사용자 편의를 위해 제공되는 기계 번역입니다. 영어 버전과 한국어 버전이 서로 어긋나는 경우에는 언제나 영어 버전이 우선합니다.

Cisco Nexus 92300YC 스위치를 교체합니다

기여자

클러스터 네트워크에서 결함이 있는 Nexus 92300YC 스위치를 교체하는 것은 무중단 절차(NDU)입니다.

요구사항 검토

필요한 것

스위치 교체를 수행하기 전에 다음 사항을 확인하십시오.

  • 기존 클러스터 및 네트워크 인프라:

    • 기존 클러스터가 완전히 연결된 클러스터 스위치를 한 개 이상 사용하여 완전하게 작동하는 것으로 확인되었습니다.

    • 모든 클러스터 포트가 작동 중입니다.

    • 모든 클러스터 논리 인터페이스(LIF)가 홈 포트에 있습니다.

    • ONTAP cluster ping -cluster -node node1 명령은 기본 접속과 PMTU 통신 이상의 통신이 모든 경로에서 성공했음을 나타내야 합니다.

  • Nexus 92300YC 교체 스위치의 경우:

    • 교체 스위치의 관리 네트워크 연결이 작동합니다.

    • 교체 스위치에 대한 콘솔 액세스가 있습니다.

    • 노드 연결은 1/1 - 1/64의 포트입니다.

    • 모든 ISL(Inter-Switch Link) 포트는 포트 1/65 및 1/66에서 비활성화됩니다.

    • 원하는 RCF(Reference Configuration File) 및 NX-OS 운영 체제 이미지 스위치가 스위치에 로드됩니다.

    • 스위치의 초기 사용자 지정이 완료되었습니다. 자세한 내용은 다음을 참조하십시오. "Cisco Nexus 92300YC 스위치를 구성합니다".

      STP, SNMP, SSH 등의 이전 사이트 사용자 지정이 새 스위치에 복사됩니다.

스위치를 교체합니다

예를 참조하십시오

이 절차의 예에서는 다음 스위치 및 노드 명명법을 사용합니다.

  • 기존 Nexus 92300YC 스위치의 이름은 CS1 및 CS2입니다.

  • 새 Nexus 92300YC 스위치의 이름은 newcs2입니다.

  • 노드 이름은 노드 1과 노드 2입니다.

  • 각 노드의 클러스터 포트 이름은 e0a 및 e0b입니다.

  • 클러스터 LIF 이름은 노드 1의 경우 node1_clus1 및 node1_clus2이고, 노드 2의 경우 node2_clus1 및 node2_clus2입니다.

  • 모든 클러스터 노드에 대한 변경 프롬프트는 cluster1:: *>입니다

이 작업에 대해

클러스터 LIF가 호스팅된 노드에서 클러스터 LIF를 마이그레이션하기 위한 명령을 실행해야 합니다.

다음 절차는 클러스터 네트워크 토폴로지를 기준으로 합니다.

토폴로지 표시
cluster1::*> network port show -ipspace Cluster

Node: node1
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e0a       Cluster      Cluster          up   9000  auto/10000 healthy  false
e0b       Cluster      Cluster          up   9000  auto/10000 healthy  false

Node: node2
                                                                       Ignore
                                                  Speed(Mbps) Health   Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
--------- ------------ ---------------- ---- ---- ----------- -------- ------
e0a       Cluster      Cluster          up   9000  auto/10000 healthy  false
e0b       Cluster      Cluster          up   9000  auto/10000 healthy  false
4 entries were displayed.



cluster1::*> network interface show -vserver Cluster
            Logical    Status     Network            Current       Current Is
Vserver     Interface  Admin/Oper Address/Mask       Node          Port    Home
----------- ---------- ---------- ------------------ ------------- ------- ----
Cluster
            node1_clus1  up/up    169.254.209.69/16  node1         e0a     true
            node1_clus2  up/up    169.254.49.125/16  node1         e0b     true
            node2_clus1  up/up    169.254.47.194/16  node2         e0a     true
            node2_clus2  up/up    169.254.19.183/16  node2         e0b     true
4 entries were displayed.



cluster1::*> network device-discovery show -protocol cdp
Node/       Local  Discovered
Protocol    Port   Device (LLDP: ChassisID)  Interface         Platform
----------- ------ ------------------------- ----------------  ----------------
node2      /cdp
            e0a    cs1                       Eth1/2            N9K-C92300YC
            e0b    cs2                       Eth1/2            N9K-C92300YC
node1      /cdp
            e0a    cs1                       Eth1/1            N9K-C92300YC
            e0b    cs2                       Eth1/1            N9K-C92300YC
4 entries were displayed.



cs1# show cdp neighbors

Capability Codes: R - Router, T - Trans-Bridge, B - Source-Route-Bridge
                  S - Switch, H - Host, I - IGMP, r - Repeater,
                  V - VoIP-Phone, D - Remotely-Managed-Device,
                  s - Supports-STP-Dispute

Device-ID          Local Intrfce  Hldtme Capability  Platform      Port ID
node1              Eth1/1         144    H           FAS2980       e0a
node2              Eth1/2         145    H           FAS2980       e0a
cs2(FDO220329V5)   Eth1/65        176    R S I s     N9K-C92300YC  Eth1/65
cs2(FDO220329V5)   Eth1/66        176    R S I s     N9K-C92300YC  Eth1/66

Total entries displayed: 4



cs2# show cdp neighbors

Capability Codes: R - Router, T - Trans-Bridge, B - Source-Route-Bridge
                  S - Switch, H - Host, I - IGMP, r - Repeater,
                  V - VoIP-Phone, D - Remotely-Managed-Device,
                  s - Supports-STP-Dispute

Device-ID          Local Intrfce  Hldtme Capability  Platform      Port ID
node1              Eth1/1         139    H           FAS2980       e0b
node2              Eth1/2         124    H           FAS2980       e0b
cs1(FDO220329KU)   Eth1/65        178    R S I s     N9K-C92300YC  Eth1/65
cs1(FDO220329KU)   Eth1/66        178    R S I s     N9K-C92300YC  Eth1/66

Total entries displayed: 4

1단계: 교체 준비

  1. 스위치에 적절한 RCF 및 이미지를 설치하고 newcs2를 설치한 후 필요한 현장 준비를 합니다.

    필요한 경우 새 스위치에 적합한 버전의 RCF 및 NX-OS 소프트웨어를 확인, 다운로드 및 설치합니다. 새 스위치가 올바르게 설정되어 있고 RCF 및 NX-OS 소프트웨어 업데이트가 필요하지 않은 경우 2단계를 계속 진행하십시오.

    1. NetApp Support 사이트에서 _NetApp 클러스터 및 관리 네트워크 스위치 참조 구성 파일 설명 페이지_로 이동하십시오.

    2. 클러스터 네트워크 및 관리 네트워크 호환성 매트릭스 _ 에 대한 링크를 클릭한 다음 필요한 스위치 소프트웨어 버전을 확인합니다.

    3. 브라우저의 뒤로 화살표를 클릭하여 * 설명 * 페이지로 돌아가 * 계속 * 을 클릭하고 사용권 계약에 동의한 다음 * 다운로드 * 페이지로 이동합니다.

    4. 다운로드 페이지의 단계에 따라 설치할 ONTAP 소프트웨어 버전에 맞는 올바른 RCF 및 NX-OS 파일을 다운로드하십시오.

  2. 새 스위치에서 admin으로 로그인하고 노드 클러스터 인터페이스(포트 1/1 - 1/64)에 연결할 모든 포트를 종료합니다.

    교체 중인 스위치가 작동하지 않고 전원이 꺼진 경우 4단계로 이동합니다. 클러스터 노드의 LIF는 각 노드의 다른 클러스터 포트로 페일오버했어야 합니다.

    예제 보기
    newcs2# config
    Enter configuration commands, one per line. End with CNTL/Z.
    newcs2(config)# interface e1/1-64
    newcs2(config-if-range)# shutdown
  3. 모든 클러스터 LIF에서 자동 되돌리기 기능이 설정되어 있는지 확인합니다.

    'network interface show-vserver Cluster-fields auto-revert'

    예제 보기
    cluster1::> network interface show -vserver Cluster -fields auto-revert
    
                 Logical
    Vserver      Interface     Auto-revert
    ------------ ------------- -------------
    Cluster      node1_clus1   true
    Cluster      node1_clus2   true
    Cluster      node2_clus1   true
    Cluster      node2_clus2   true
    
    4 entries were displayed.
  4. 모든 클러스터 LIF가 통신할 수 있는지 확인:

    '클러스터 ping 클러스터'

    예제 보기
    cluster1::*> cluster ping-cluster node1
    
    Host is node2
    Getting addresses from network interface table...
    Cluster node1_clus1 169.254.209.69 node1 e0a
    Cluster node1_clus2 169.254.49.125 node1 e0b
    Cluster node2_clus1 169.254.47.194 node2 e0a
    Cluster node2_clus2 169.254.19.183 node2 e0b
    Local = 169.254.47.194 169.254.19.183
    Remote = 169.254.209.69 169.254.49.125
    Cluster Vserver Id = 4294967293
    Ping status:
    ....
    Basic connectivity succeeds on 4 path(s)
    Basic connectivity fails on 0 path(s)
    ................
    Detected 9000 byte MTU on 4 path(s):
    Local 169.254.47.194 to Remote 169.254.209.69
    Local 169.254.47.194 to Remote 169.254.49.125
    Local 169.254.19.183 to Remote 169.254.209.69
    Local 169.254.19.183 to Remote 169.254.49.125
    Larger than PMTU communication succeeds on 4 path(s)
    RPC status:
    2 paths up, 0 paths down (tcp check)
    2 paths up, 0 paths down (udp check)

2단계: 케이블 및 포트 구성

  1. Nexus 92300YC 스위치 CS1에서 ISL 포트 1/65 및 1/66을 종료합니다.

    예제 보기
    cs1# configure
    Enter configuration commands, one per line. End with CNTL/Z.
    cs1(config)# interface e1/65-66
    cs1(config-if-range)# shutdown
    cs1(config-if-range)#
  2. Nexus 92300YC CS2 스위치에서 모든 케이블을 분리한 다음 Nexus 92300YC newcs2 스위치의 같은 포트에 연결합니다.

  3. CS1과 newcs2 스위치 사이에 ISL 포트 1/65 및 1/66을 표시한 다음 포트 채널 작동 상태를 확인합니다.

    포트-채널은 PO1(SU)을 나타내고 구성원 포트는 Eth1/65(P) 및 Eth1/66(P)을 나타내야 합니다.

    예제 보기

    이 예에서는 ISL 포트 1/65 및 1/66을 활성화하고 스위치 CS1에 포트 채널 요약을 표시합니다.

    cs1# configure
    Enter configuration commands, one per line. End with CNTL/Z.
    cs1(config)# int e1/65-66
    cs1(config-if-range)# no shutdown
    
    cs1(config-if-range)# show port-channel summary
    Flags:  D - Down        P - Up in port-channel (members)
            I - Individual  H - Hot-standby (LACP only)
            s - Suspended   r - Module-removed
            b - BFD Session Wait
            S - Switched    R - Routed
            U - Up (port-channel)
            p - Up in delay-lacp mode (member)
            M - Not in use. Min-links not met
    --------------------------------------------------------------------------------
    Group Port-       Type     Protocol  Member Ports
          Channel
    --------------------------------------------------------------------------------
    1     Po1(SU)     Eth      LACP      Eth1/65(P)   Eth1/66(P)
    
    cs1(config-if-range)#
  4. 모든 노드에서 포트 e0b가 작동 중인지 확인:

    네트워크 포트에는 IPSpace 클러스터가 표시됩니다

    예제 보기

    출력은 다음과 비슷해야 합니다.

    cluster1::*> network port show -ipspace Cluster
    
    Node: node1
                                                                            Ignore
                                                       Speed(Mbps) Health   Health
    Port      IPspace      Broadcast Domain Link MTU   Admin/Oper  Status   Status
    --------- ------------ ---------------- ---- ----- ----------- -------- -------
    e0a       Cluster      Cluster          up   9000  auto/10000  healthy  false
    e0b       Cluster      Cluster          up   9000  auto/10000  healthy  false
    
    Node: node2
                                                                            Ignore
                                                       Speed(Mbps) Health   Health
    Port      IPspace      Broadcast Domain Link MTU   Admin/Oper  Status   Status
    --------- ------------ ---------------- ---- ----- ----------- -------- -------
    e0a       Cluster      Cluster          up   9000  auto/10000  healthy  false
    e0b       Cluster      Cluster          up   9000  auto/auto   -        false
    
    4 entries were displayed.
  5. 이전 단계에서 사용한 것과 동일한 노드에서 네트워크 인터페이스 되돌리기 명령을 사용하여 이전 단계의 포트에 연결된 클러스터 LIF를 되돌립니다.

    예제 보기

    이 예제에서는 Home 값이 true 이고 포트가 e0b인 경우 노드 1의 LIF node1_clus2가 성공적으로 되돌려집니다.

    다음 명령을 실행하면 node1의 node1_clus2 가 홈 포트 e0a로 반환되고 두 노드의 LIF에 대한 정보가 표시됩니다. 첫 번째 노드를 가져오는 작업은 두 클러스터 인터페이스 모두에 대해 "홈" 열이 참이고 노드 1의 "e0a" 및 "e0b" 예제에서 올바른 포트 할당을 표시하는 경우 성공적으로 완료된 것입니다.

    cluster1::*> network interface show -vserver Cluster
    
                Logical      Status     Network            Current    Current Is
    Vserver     Interface    Admin/Oper Address/Mask       Node       Port    Home
    ----------- ------------ ---------- ------------------ ---------- ------- -----
    Cluster
                node1_clus1  up/up      169.254.209.69/16  node1      e0a     true
                node1_clus2  up/up      169.254.49.125/16  node1      e0b     true
                node2_clus1  up/up      169.254.47.194/16  node2      e0a     true
                node2_clus2  up/up      169.254.19.183/16  node2      e0a     false
    
    4 entries were displayed.
  6. 클러스터의 노드에 대한 정보를 표시합니다.

    '클러스터 쇼'

    예제 보기

    이 예제에서는 이 클러스터의 노드 1과 노드 2에 대한 노드 상태가 true인 것을 보여 줍니다.

    cluster1::*> cluster show
    
    Node          Health  Eligibility
    ------------- ------- ------------
    node1         false   true
    node2         true    true
  7. 모든 물리적 클러스터 포트가 작동하는지 확인합니다.

    네트워크 포트에는 IPSpace 클러스터가 표시됩니다

    예제 보기
    cluster1::*> network port show -ipspace Cluster
    
    Node: node1
    																																									 					 																					 	  Ignore
                                                        Speed(Mbps) Health   Health
    Port      IPspace     Broadcast Domain  Link  MTU   Admin/Oper  Status   Status
    --------- ----------- ----------------- ----- ----- ----------- -------- ------
    e0a       Cluster     Cluster           up    9000  auto/10000  healthy  false
    e0b       Cluster     Cluster           up    9000  auto/10000  healthy  false
    
    Node: node2
                                                                             Ignore
                                                        Speed(Mbps) Health   Health
    Port      IPspace      Broadcast Domain Link  MTU   Admin/Oper  Status   Status
    --------- ------------ ---------------- ----- ----- ----------- -------- ------
    e0a       Cluster      Cluster          up    9000  auto/10000  healthy  false
    e0b       Cluster      Cluster          up    9000  auto/10000  healthy  false
    
    4 entries were displayed.

3단계: 절차를 완료합니다

  1. 모든 클러스터 LIF가 통신할 수 있는지 확인:

    '클러스터 ping 클러스터'

    예제 보기
    cluster1::*> cluster ping-cluster -node node2
    Host is node2
    Getting addresses from network interface table...
    Cluster node1_clus1 169.254.209.69 node1 e0a
    Cluster node1_clus2 169.254.49.125 node1 e0b
    Cluster node2_clus1 169.254.47.194 node2 e0a
    Cluster node2_clus2 169.254.19.183 node2 e0b
    Local = 169.254.47.194 169.254.19.183
    Remote = 169.254.209.69 169.254.49.125
    Cluster Vserver Id = 4294967293
    Ping status:
    ....
    Basic connectivity succeeds on 4 path(s)
    Basic connectivity fails on 0 path(s)
    ................
    Detected 9000 byte MTU on 4 path(s):
    Local 169.254.47.194 to Remote 169.254.209.69
    Local 169.254.47.194 to Remote 169.254.49.125
    Local 169.254.19.183 to Remote 169.254.209.69
    Local 169.254.19.183 to Remote 169.254.49.125
    Larger than PMTU communication succeeds on 4 path(s)
    RPC status:
    2 paths up, 0 paths down (tcp check)
    2 paths up, 0 paths down (udp check)
  2. 다음 클러스터 네트워크 구성을 확인합니다.

    네트워크 포트 쇼

    예제 보기
    cluster1::*> network port show -ipspace Cluster
    Node: node1
    																																																																			 	  Ignore
                                           Speed(Mbps)            Health   Health
    Port      IPspace     Broadcast Domain Link MTU   Admin/Oper  Status   Status
    --------- ----------- ---------------- ---- ----- ----------- -------- ------
    e0a       Cluster     Cluster          up   9000  auto/10000  healthy  false
    e0b       Cluster     Cluster          up   9000  auto/10000  healthy  false
    
    Node: node2
                                                                           Ignore
                                            Speed(Mbps)           Health   Health
    Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status   Status
    --------- ------------ ---------------- ---- ---- ----------- -------- ------
    e0a       Cluster      Cluster          up   9000 auto/10000  healthy  false
    e0b       Cluster      Cluster          up   9000 auto/10000  healthy  false
    
    4 entries were displayed.
    
    
    cluster1::*> network interface show -vserver Cluster
    
                Logical    Status     Network            Current       Current Is
    Vserver     Interface  Admin/Oper Address/Mask       Node          Port    Home
    ----------- ---------- ---------- ------------------ ------------- ------- ----
    Cluster
                node1_clus1  up/up    169.254.209.69/16  node1         e0a     true
                node1_clus2  up/up    169.254.49.125/16  node1         e0b     true
                node2_clus1  up/up    169.254.47.194/16  node2         e0a     true
                node2_clus2  up/up    169.254.19.183/16  node2         e0b     true
    
    4 entries were displayed.
    
    cluster1::> network device-discovery show -protocol cdp
    
    Node/       Local  Discovered
    Protocol    Port   Device (LLDP: ChassisID)  Interface         Platform
    ----------- ------ ------------------------- ----------------  ----------------
    node2      /cdp
                e0a    cs1                       0/2               N9K-C92300YC
                e0b    newcs2                    0/2               N9K-C92300YC
    node1      /cdp
                e0a    cs1                       0/1               N9K-C92300YC
                e0b    newcs2                    0/1               N9K-C92300YC
    
    4 entries were displayed.
    
    
    cs1# show cdp neighbors
    
    Capability Codes: R - Router, T - Trans-Bridge, B - Source-Route-Bridge
                      S - Switch, H - Host, I - IGMP, r - Repeater,
                      V - VoIP-Phone, D - Remotely-Managed-Device,
                      s - Supports-STP-Dispute
    
    Device-ID            Local Intrfce  Hldtme Capability  Platform      Port ID
    node1                Eth1/1         144    H           FAS2980       e0a
    node2                Eth1/2         145    H           FAS2980       e0a
    newcs2(FDO296348FU)  Eth1/65        176    R S I s     N9K-C92300YC  Eth1/65
    newcs2(FDO296348FU)  Eth1/66        176    R S I s     N9K-C92300YC  Eth1/66
    
    
    Total entries displayed: 4
    
    
    cs2# show cdp neighbors
    
    Capability Codes: R - Router, T - Trans-Bridge, B - Source-Route-Bridge
                      S - Switch, H - Host, I - IGMP, r - Repeater,
                      V - VoIP-Phone, D - Remotely-Managed-Device,
                      s - Supports-STP-Dispute
    
    Device-ID          Local Intrfce  Hldtme Capability  Platform      Port ID
    node1              Eth1/1         139    H           FAS2980       e0b
    node2              Eth1/2         124    H           FAS2980       e0b
    cs1(FDO220329KU)   Eth1/65        178    R S I s     N9K-C92300YC  Eth1/65
    cs1(FDO220329KU)   Eth1/66        178    R S I s     N9K-C92300YC  Eth1/66
    
    Total entries displayed: 4
  3. ONTAP 9.4 이상의 경우 gthe commamds를 사용하여 스위치 관련 로그 파일을 수집하기 위해 클러스터 스위치 상태 모니터 로그 수집 기능을 활성화합니다.

    System cluster-switch log setup-password와 system cluster-switch log enable-collection

    예제 보기
    cluster1::*> system cluster-switch log setup-password
    Enter the switch name: <return>
    The switch name entered is not recognized.
    Choose from the following list:
    cs1
    cs2
    
    cluster1::*> system cluster-switch log setup-password
    
    Enter the switch name: cs1
    RSA key fingerprint is e5:8b:c6:dc:e2:18:18:09:36:63:d9:63:dd:03:d9:cc
    Do you want to continue? {y|n}::[n] y
    
    Enter the password: <enter switch password>
    Enter the password again: <enter switch password>
    
    cluster1::*> system cluster-switch log setup-password
    
    Enter the switch name: cs2
    RSA key fingerprint is 57:49:86:a1:b9:80:6a:61:9a:86:8e:3c:e3:b7:1f:b1
    Do you want to continue? {y|n}:: [n] y
    
    Enter the password: <enter switch password>
    Enter the password again: <enter switch password>
    
    cluster1::*> system cluster-switch log enable-collection
    
    Do you want to enable cluster log collection for all nodes in the cluster?
    {y|n}: [n] y
    
    Enabling cluster switch log collection.
    
    cluster1::*>
    참고 이러한 명령에서 오류가 반환되면 NetApp 지원에 문의하십시오.