Skip to main content
简体中文版经机器翻译而成，仅供参考。如与英语版出现任何冲突，应以英语版为准。

配置Cisco Nexus 92300YC 交换机

贡献者 netapp-jolieg netapp-yvonneo
PDF

按照以下步骤设置和配置Cisco Nexus 92300YC 交换机。

步骤

  1. 将串口连接到主机或串口。

  2. 将管理端口（交换机的非端口侧）连接到 SFTP 服务器所在的同一网络。

  3. 在控制台上，设置主机端串口设置：

    • 9600波特

    • 8 位数据

    • 1 停止位

    • 奇偶性：无

    • 流量控制：无

  4. 首次启动或在擦除运行配置后重新启动时，Nexus 92300YC 交换机会陷入启动循环。输入 yes 即可中断此循环，中止开机自动配置。

    显示系统管理员帐户设置。

    显示示例 
    $ VDC-1 %$ %POAP-2-POAP_INFO:   - Abort Power On Auto Provisioning [yes - continue with normal setup, skip - bypass password and basic configuration, no - continue with Power On Auto Provisioning] (yes/skip/no)[no]: y
Disabling POAP.......Disabling POAP
2019 Apr 10 00:36:17 switch %$ VDC-1 %$ poap: Rolling back, please wait... (This may take 5-15 minutes)

          ---- System Admin Account Setup ----

Do you want to enforce secure password standard (yes/no) [y]:

  5. 输入 y 以强制执行安全密码标准：

    Do you want to enforce secure password standard (yes/no) [y]: y

  6. 请输入并确认管理员用户的密码：

    Enter the password for "admin":
Confirm the password for "admin":

  7. 输入 yes 进入基本系统配置对话框。

    显示示例 
    This setup utility will guide you through the basic configuration of
the system. Setup configures only enough connectivity for management
of the system.

Please register Cisco Nexus9000 Family devices promptly with your
supplier. Failure to register may affect response times for initial
service calls. Nexus9000 devices must be registered to receive
entitled support services.

Press Enter at anytime to skip a dialog. Use ctrl-c at anytime
to skip the remaining dialogs.

Would you like to enter the basic configuration dialog (yes/no):

  8. 创建另一个登录帐户：

    Create another login account (yes/no) [n]:

  9. 配置只读和读写 SNMP 团体字符串：

    Configure read-only SNMP community string (yes/no) [n]:

Configure read-write SNMP community string (yes/no) [n]:

  10. 配置集群交换机名称：

    Enter the switch name : cs2

  11. 配置带外管理接口：

    Continue with Out-of-band (mgmt0) management configuration? (yes/no) [y]: y

Mgmt0 IPv4 address : 172.22.133.216

Mgmt0 IPv4 netmask : 255.255.224.0

Configure the default gateway? (yes/no) [y]: y

IPv4 address of the default gateway : 172.22.128.1

  12. 配置高级 IP 选项：

    Configure advanced IP options? (yes/no) [n]: n

  13. 配置 Telnet 服务：

    Enable the telnet service? (yes/no) [n]: n

  14. 配置SSH服务和SSH密钥：

    Enable the ssh service? (yes/no) [y]: y

       Type of ssh key you would like to generate (dsa/rsa) [rsa]: rsa

       Number of rsa key bits <1024-2048> [1024]: 2048

  15. 配置其他设置：

    Configure the ntp server? (yes/no) [n]: n

  Configure default interface layer (L3/L2) [L2]: L2

  Configure default switchport interface state (shut/noshut) [noshut]: noshut

  Configure CoPP system profile (strict/moderate/lenient/dense) [strict]: strict

  16. 确认交换机信息并保存配置：

    Would you like to edit the configuration? (yes/no) [n]: n

Use this configuration and save it? (yes/no) [y]: y

[] 100%
Copy complete, now saving to disk (please wait)...
Copy complete.
下一步是什么？

配置好交换机后，您可以…… "准备安装NX-OS软件和RCF"。