Sostituire uno switch di storage Cisco Nexus 3232C
Per sostituire uno switch storage Cisco Nexus 3232C difettoso, procedere come segue. Si tratta di una procedura senza interruzioni.
Verifica dei requisiti
La configurazione di rete esistente deve avere le seguenti caratteristiche:
-
La pagina Cisco Ethernet Switches (Switch Ethernet Cisco) contiene le ultime versioni RCF e NX-OS sugli switch.
-
La connettività di gestione deve esistere su entrambi gli switch.
Assicurarsi che tutte le fasi di risoluzione dei problemi siano state completate per confermare che lo switch deve essere sostituito.
Lo switch Cisco Nexus 3232C sostitutivo deve avere le seguenti caratteristiche:
-
La connettività della rete di gestione deve essere funzionale.
-
L'accesso della console allo switch sostitutivo deve essere in posizione.
-
Sullo switch deve essere caricata l'immagine appropriata del sistema operativo RCF e NX-OS.
-
La personalizzazione iniziale dello switch deve essere completata.
Sostituire lo switch
Questa procedura sostituisce il secondo switch di storage Nexus 3232C S2 con il nuovo switch NS2 3232C. I due nodi sono node1 e node2.
Fase 1: Verificare che l'interruttore da sostituire sia S2
-
Se AutoSupport è attivato su questo cluster, eliminare la creazione automatica del caso richiamando un messaggio AutoSupport:
system node autosupport invoke -node * -type all - message MAINT=xh
x è la durata della finestra di manutenzione in ore.
Il messaggio AutoSupport informa il supporto tecnico di questa attività di manutenzione in modo che la creazione automatica del caso venga soppressa durante la finestra di manutenzione.
-
Controllare lo stato delle porte dei nodi di storage per verificare che vi sia una connessione allo switch di storage S1:
storage port show -port-type ENET
Mostra esempio
storage::*> storage port show -port-type ENET Speed VLAN Node Port Type Mode (Gb/s) State Status ID ------------------ ---- ----- ------- ------ -------- --------- ---- node1 e3a ENET storage 100 enabled online 30 e3b ENET storage 0 enabled offline 30 e7a ENET storage 0 enabled offline 30 e7b ENET storage 0 enabled offline 30 node2 e3a ENET storage 100 enabled online 30 e3b ENET storage 0 enabled offline 30 e7a ENET storage 0 enabled offline 30 e7b ENET storage 0 enabled offline 30
-
Verificare che lo switch di storage S1 sia disponibile:
network device-discovery show
Mostra esempio
storage::*> network device-discovery show Node/ Local Discovered Protocol Port Device (LLDP: ChassisID) Interface Platform ----------- ------ ------------------------- ----------------- ---------------- node1/cdp e3a S1 Ethernet1/1 NX3232C e4a node2 e4a AFF-A700 e4e node2 e4e AFF-A700 node1/lldp e3a S1 Ethernet1/1 - e4a node2 e4a - e4e node2 e4e - node2/cdp e3a S1 Ethernet1/2 NX3232C e4a node1 e4a AFF-A700 e4e node1 e4e AFF-A700 node2/lldp e3a S1 Ethernet1/2 - e4a node1 e4a - e4e node1 e4e -
-
Eseguire
show lldp neighbors
comando sull'interruttore funzionante per confermare che è possibile visualizzare sia i nodi che tutti gli shelf:show lldp neighbors
Mostra esempio
S1# show lldp neighbors Capability codes: (R) Router, (B) Bridge, (T) Telephone, (C) DOCSIS Cable Device (W) WLAN Access Point, (P) Repeater, (S) Station, (O) Other Device ID Local Intf Hold-time Capability Port ID node1 Eth1/1 121 S e3a node2 Eth1/2 121 S e3a SHFGD2008000011 Eth1/5 121 S e0a SHFGD2008000011 Eth1/6 120 S e0a SHFGD2008000022 Eth1/7 120 S e0a SHFGD2008000022 Eth1/8 120 S e0a
Fase 2: Configurare il cablaggio
-
verificare le porte dello shelf nel sistema storage:
storage shelf port show -fields remote-device,remote-port
Mostra esempio
storage::*> storage shelf port show -fields remote-device,remote-port shelf id remote-port remote-device ----- -- ----------- ------------- 3.20 0 Ethernet1/5 S1 3.20 1 - - 3.20 2 Ethernet1/6 S1 3.20 3 - - 3.30 0 Ethernet1/7 S1 3.20 1 - - 3.30 2 Ethernet1/8 S1 3.20 3 - -
-
Rimuovere tutti i cavi collegati allo switch di storage S2.
-
Ricollegare tutti i cavi allo switch NS2 sostitutivo.
Fase 3: Verificare tutte le configurazioni del dispositivo sullo switch NS2
-
Verificare lo stato di integrità delle porte del nodo di storage:
storage port show -port-type ENET
Mostra esempio
storage::*> storage port show -port-type ENET Speed VLAN Node Port Type Mode (Gb/s) State Status ID ------------------ ---- ----- ------- ------ -------- ------------ --- node1 e3a ENET storage 100 enabled online 30 e3b ENET storage 0 enabled offline 30 e7a ENET storage 0 enabled offline 30 e7b ENET storage 100 enabled online 30 node2 e3a ENET storage 100 enabled online 30 e3b ENET storage 0 enabled offline 30 e7a ENET storage 0 enabled offline 30 e7b ENET storage 100 enabled online 30
-
Verificare che entrambi gli switch siano disponibili:
network device-discovery show
Mostra esempio
storage::*> network device-discovery show Node/ Local Discovered Protocol Port Device (LLDP: ChassisID) Interface Platform ----------- ------ ------------------------- ---------------- -------- node1/cdp e3a S1 Ethernet1/1 NX3232C e4a node2 e4a AFF-A700 e4e node2 e4e AFF-A700 e7b NS2 Ethernet1/1 NX3232C node1/lldp e3a S1 Ethernet1/1 - e4a node2 e4a - e4e node2 e4e - e7b NS2 Ethernet1/1 - node2/cdp e3a S1 Ethernet1/2 NX3232C e4a node1 e4a AFF-A700 e4e node1 e4e AFF-A700 e7b NS2 Ethernet1/2 NX3232C node2/lldp e3a S1 Ethernet1/2 - e4a node1 e4a - e4e node1 e4e - e7b NS2 Ethernet1/2 -
-
Verificare le porte dello shelf nel sistema storage:
storage shelf port show -fields remote-device,remote-port
Mostra esempio
storage::*> storage shelf port show -fields remote-device,remote-port shelf id remote-port remote-device ----- -- ----------- ------------- 3.20 0 Ethernet1/5 S1 3.20 1 Ethernet1/5 NS2 3.20 2 Ethernet1/6 S1 3.20 3 Ethernet1/6 NS2 3.30 0 Ethernet1/7 S1 3.20 1 Ethernet1/7 NS2 3.30 2 Ethernet1/8 S1 3.20 3 Ethernet1/8 NS2
-
Se è stata eliminata la creazione automatica del caso, riattivarla richiamando un messaggio AutoSupport:
system node autosupport invoke -node * -type all -message MAINT=END