Skip to main content

Move NAS data LIFs owned by node1 to node2

Contributors netapp-pcarriga netapp-aoife netapp-aherbin
PDFs

Before you can replace node1 with node3, you must move the NAS data LIFs owned by node1 to node2 if you have a two-node cluster, or to a third node if your cluster has more than two nodes. The method you use depends on whether the cluster is configured for NAS or SAN.

About this task

Remote LIFs handle traffic to SAN LUNs during the upgrade procedure. Moving SAN LIFs is not necessary for cluster or service health during the upgrade. You must verify that the LIFs are healthy and located on appropriate ports after you bring node3 online.

Steps

  1. List all the NAS data LIFs hosted on node1 by entering the following command and capturing the output:

    network interface show -data-protocol nfs|cifs -curr-node node1

    The system displays the NAS data LIFs on node1, as shown in the following example:

     cluster::> network interface show -data-protocol nfs|cifs -curr-node node1

          Logical     Status      Network             Current   Current Is
 Vserver  Interface   Admin/Oper  Address/Mask        Node      Port    Home
 -------- ----------  ----------  ------------------  --------- ------- ----
 vs0
          a0a         up/down     10.63.0.53/24       node1     a0a     true
          data1       up/up       10.63.0.50/18       node1     e0c     true
          rads1       up/up       10.63.0.51/18       node1     e1a     true
          rads2       up/down     10.63.0.52/24       node1     e1b     true
 vs1
          lif1        up/up       192.17.176.120/24   node1     e0c     true
          lif2        up/up       172.17.176.121/24   node1     e1a     true

  2. Take one of the following actions:

    If node1…​ Then…​

    Has interface groups of VLANs configured

    Go to Step 3.

    Does not have interface groups or VLANs configured

    Skip Step 3 and go to Step 4.

    Use the network port vlan show command to display information about the network ports attached to VLANs, and use the network port ifgrp show command to display information about the port interface groups.

  3. Take the following steps to migrate any NAS data LIFs hosted on interface groups and VLANs on node1:

    1. Migrate the LIFs hosted on any interface groups and the VLANs on node1 to a port on node2 that is capable of hosting LIFs on the same network as that of the interface groups by entering the following command, once for each LIF:

      network interface migrate -vserver Vserver_name -lif LIF_name -destination-node node2 –destination-port netport|ifgrp

    2. Modify the home port and the home node of the LIFs and VLANs in Substep a to the port and node currently hosting the LIFs by entering the following command, once for each LIF:

      network interface modify -vserver Vserver_name -lif LIF_name -home-node node2 - home-port netport|ifgrp

  4. Take one of the following actions:

    If the cluster is configured for…​ Then…​

    NAS

    Complete Step 5 through Step 8.

    SAN

    Disable all the SAN LIFs on the node to take them down for the upgrade:

    network interface modify -vserver Vserver-name -lif LIF_name -home-node node_to_upgrade -home-port netport|ifgrp -status-admin down

  5. Migrate NAS data LIFs from node1 to node2 by entering the following command, once for each data LIF:

    network interface migrate -vserver Vserver-name -lif LIF_name -destination-node node2 -destination-port data_port

  6. Enter the following command and examine its output to verify that LIFs have been moved to the correct ports and that the LIFs have the status of up by entering the following command on either node and examining the output:

    network interface show -curr-node node2 -data-protocol nfs|cifs

  7. Enter the following command to modify the home node of the migrated LIFs:

    network interface modify -vserver Vserver-name -lif LIF_name -home-node node2 -home-port port_name

  8. Verify whether the LIF is using the port as its home or current port. If the port is not home or current port then go to Step 9:

    network interface show -home-node node2 -home-port port_name

    network interface show -curr-node node_name -curr-port port_name

  9. If the LIFs are using the port as a home port or current port, then modify the LIF to use a different port:

    network interface migrate -vserver Vserver-name -lif LIF_name -destination–node node_name -destination-port port_name

    network interface modify -vserver Vserver-name -lif LIF_name -home–node node_name -home-port port_name

  10. If the ports currently hosting data LIFs are not going to exist on the new hardware, remove them from the broadcast domain now:

    network port broadcast-domain remove-ports -ipspace Default -broadcast-domain Default -ports node:port

  11. If any LIFs are down, set the administrative status of the LIFs to "up" by entering the following command, once for each LIF:

    network interface modify -vserver Vserver-name -lif LIF_name -home-node nodename -status-admin up

    Note For MetroCluster configurations, you might not be able to change the broadcast domain of a port because it is associated with a port hosting the LIF of a destination storage virtual machine (SVM). Enter the following command from the corresponding source SVM on the remote site to reallocate the destination LIF to an appropriate port:
    metrocluster vserver resync -vserver Vserver_name

  12. Enter the following command and examine its output to verify that there are no data LIFs remaining on node1:

    network interface show -curr-node node1 -role data

  13. If you have interface groups or VLANs configured, complete the following substeps:

    1. Remove the VLANs from the interface groups by entering the following command:

      network port vlan delete -node nodename -port ifgrp_name -vlan-id VLAN_ID

    2. Enter the following command and examine its output to see if there are any interface groups configured on the node:

      network port ifgrp show -node nodename -ifgrp ifgrp_name -instance

      The system displays interface group information for the node as shown in the following example:

        cluster::> network port ifgrp show -node node1 -ifgrp a0a -instance
                   Node: node1
   Interface Group Name: a0a
  Distribution Function: ip
          Create Policy: multimode_lacp
            MAC Address: 02:a0:98:17:dc:d4
     Port Participation: partial
          Network Ports: e2c, e2d
               Up Ports: e2c
             Down Ports: e2d

    3. If any interface groups are configured on the node, record the names of those groups and the ports assigned to them, and then delete the ports by entering the following command, once for each port:

      network port ifgrp remove-port -node nodename -ifgrp ifgrp_name -port netport