You need to verify that you are using the specified port assignments when you cable the FC switches when using ONTAP 9.1 and later.
Ports that are not used for attaching initiator ports, FC-VI ports, or ISLs can be reconfigured to act as storage ports. However, if the supported RCFs are being used, the zoning must be changed accordingly.
If the supported RCFs are used, ISL ports might not connect to the same ports shown here and might need to be reconfigured manually.
If you configured your switches using the port assignments for ONTAP 9, you can continue to use the older assignments. However, new configurations running ONTAP 9.1 or later releases should use the port assignments shown here.
For other storage systems, use the cabling shown in the tables but ignore the cabling for FC-VI ports c and d.
You can leave those ports empty.
The number of ISLs you cable may vary depending on your site's requirements.
See the section on ISL considerations.
The following tables show port usage on Brocade switches. The tables show the maximum supported configuration, with eight controller modules in two DR groups. For smaller configurations, ignore the rows for the additional controller modules. Note that eight ISLs are supported only on the Brocade 6510, Brocade DCX 8510-8, G620, G630, G620-1, G630-1, and G720 switches.
Configurations using FibreBridge 6500N bridges or FibreBridge 7500N or 7600N using one FC port (FC1 or FC2) only | ||||
---|---|---|---|---|
MetroCluster 1 or DR Group 1 | ||||
Component | Port | Brocade switch models 6505, 6510, 6520, 7810, 7840, G610, G620, G620-1, G630, G630-1 and DCX 8510-8 | Brocade switch model G720 | |
Connects to FC switch... | Connects to switch port... | Connects to switch port... | ||
controller_x_1 | FC-VI port a | 1 | 0 | 0 |
FC-VI port b | 2 | 0 | 0 | |
FC-VI port c | 1 | 1 | 1 | |
FC-VI port d | 2 | 1 | 1 | |
HBA port a | 1 | 2 | 8 | |
HBA port b | 2 | 2 | 8 | |
HBA port c | 1 | 3 | 9 | |
HBA port d | 2 | 3 | 9 | |
controller_x_2 | FC-VI port a | 1 | 4 | 4 |
FC-VI port b | 2 | 4 | 4 | |
FC-VI port c | 1 | 5 | 5 | |
FC-VI port d | 2 | 5 | 5 | |
HBA port a | 1 | 6 | 12 | |
HBA port b | 2 | 6 | 12 | |
HBA port c | 1 | 7 | 13 | |
HBA port d | 2 | 7 | 13 | |
Stack 1 | bridge_x_1a | 1 | 8 | 10 |
bridge_x_1b | 2 | 8 | 10 | |
Stack 2 | bridge_x_2a | 1 | 9 | 11 |
bridge_x_2b | 2 | 9 | 11 | |
Stack 3 | bridge_x_3a | 1 | 10 | 14 |
bridge_x_4b | 2 | 10 | 14 | |
Stack y | bridge_x_ya | 1 | 11 | 15 |
bridge_x_yb | 2 | 11 | 15 | |
Note:
|
Configurations using FibreBridge 6500N bridges or FibreBridge 7500N or 7600N using one FC port (FC1 or FC2) only | |||||||
---|---|---|---|---|---|---|---|
MetroCluster 2 or DR Group 2 | |||||||
Brocade switch model | |||||||
Component | Port | Connects to FC_switch... | 6510, DCX 8510-8 | 6520 | 7840, DCX 8510-8 | G620, G620-1, G630, G630-1 | G720 |
controller_x_3 | FC-VI port a | 1 | 24 | 48 | 12 | 18 | 18 |
FC-VI port b | 2 | 24 | 48 | 12 | 18 | 18 | |
FC-VI port c | 1 | 25 | 49 | 13 | 19 | 19 | |
FC-VI port d | 2 | 25 | 49 | 13 | 19 | 19 | |
HBA port a | 1 | 26 | 50 | 14 | 24 | 26 | |
HBA port b | 2 | 26 | 50 | 14 | 24 | 26 | |
HBA port c | 1 | 27 | 51 | 15 | 25 | 27 | |
HBA port d | 2 | 27 | 51 | 15 | 25 | 27 | |
controller_x_4 | FC-VI port a | 1 | 28 | 52 | 16 | 22 | 22 |
FC-VI port b | 2 | 28 | 52 | 16 | 22 | 22 | |
FC-VI port c | 1 | 29 | 53 | 17 | 23 | 23 | |
FC-VI port d | 2 | 29 | 53 | 17 | 23 | 23 | |
HBA port a | 1 | 30 | 54 | 18 | 28 | 30 | |
HBA port b | 2 | 30 | 54 | 18 | 28 | 30 | |
HBA port c | 1 | 31 | 55 | 19 | 29 | 31 | |
HBA port d | 2 | 32 | 55 | 19 | 29 | 31 | |
Stack 1 | bridge_x_51a | 1 | 32 | 56 | 20 | 26 | 32 |
bridge_x_51b | 2 | 32 | 56 | 20 | 26 | 32 | |
Stack 2 | bridge_x_52a | 1 | 33 | 57 | 21 | 27 | 33 |
bridge_x_52b | 2 | 33 | 57 | 21 | 27 | 33 | |
Stack 3 | bridge_x_53a | 1 | 34 | 58 | 22 | 30 | 34 |
bridge_x_54b | 2 | 34 | 58 | 22 | 30 | 34 | |
Stack y | bridge_x_ya | 1 | 35 | 59 | 23 | 31 | 35 |
bridge_x_yb | 2 | 35 | 59 | 23 | 31 | 35 | |
Note:
|
Configurations using FibreBridge 7500N or 7600N using both FC ports (FC1 and FC2) | |||||
---|---|---|---|---|---|
MetroCluster 1 or DR Group 1 | |||||
Component | Port | Brocade switch models 6505, 6510, 6520, 7810, 7840, G610, G620, G620-1, G630, G630-1, and DCX 8510-8 | Brocade switch G720 | ||
Connects to FC_switch... | Connects to switch port... | Connects to switch port... | |||
controller_x_1 | FC-VI port a | 1 | 0 | 0 | |
FC-VI port b | 2 | 0 | 0 | ||
FC-VI port c | 1 | 1 | 1 | ||
FC-VI port d | 2 | 1 | 1 | ||
HBA port a | 1 | 2 | 8 | ||
HBA port b | 2 | 2 | 8 | ||
HBA port c | 1 | 3 | 9 | ||
HBA port d | 2 | 3 | 9 | ||
controller_x_2 | FC-VI port a | 1 | 4 | 4 | |
FC-VI port b | 2 | 4 | 4 | ||
FC-VI port c | 1 | 5 | 5 | ||
FC-VI port d | 2 | 5 | 5 | ||
HBA port a | 1 | 6 | 12 | ||
HBA port b | 2 | 6 | 12 | ||
HBA port c | 1 | 7 | 13 | ||
HBA port d | 2 | 7 | 13 | ||
Stack 1 | bridge_x_1a | FC1 | 1 | 8 | 10 |
FC2 | 2 | 8 | 10 | ||
bridge_x_1B | FC1 | 1 | 9 | 11 | |
FC2 | 2 | 9 | 11 | ||
Stack 2 | bridge_x_2a | FC1 | 1 | 10 | 14 |
FC2 | 2 | 10 | 14 | ||
bridge_x_2B | FC1 | 1 | 11 | 15 | |
FC2 | 2 | 11 | 15 | ||
Stack 3 | bridge_x_3a | FC1 | 1 | 12* | 16 |
FC2 | 2 | 12* | 16 | ||
bridge_x_3B | FC1 | 1 | 13* | 17 | |
FC2 | 2 | 13* | 17 | ||
Stack y | bridge_x_ya | FC1 | 1 | 14* | 20 |
FC2 | 2 | 14* | 20 | ||
bridge_x_yb | FC1 | 1 | 15* | 21 | |
FC2 | 2 | 15* | 21 | ||
* - Ports 12 through 15 are reserved for the second MetroCluster or DR group on the Brocade 7840 switch. Note: Additional bridges can be cabled to ports 16, 17, 20 and 21 in G620, G630, G620-1 and G630-1 switches.
|
Configurations using FibreBridge 7500N or 7600N using both FC ports (FC1 and FC2) | |||||||||
---|---|---|---|---|---|---|---|---|---|
MetroCluster 2 or DR Group 2 | |||||||||
Component | Port | Brocade switch model | |||||||
Connects to FC_switch... | 6510, DCX 8510-8 | 6520 | 7840, DCX 8510-8 | G620, G620-1, G630, G630-1 | G720 | ||||
controller_x_3 | FC-VI port a | 1 | 24 | 48 | 12 | 18 | 18 | ||
FC-VI port b | 2 | 24 | 48 | 12 | 18 | 18 | |||
FC-VI port c | 1 | 25 | 49 | 13 | 19 | 19 | |||
FC-VI port d | 2 | 25 | 49 | 13 | 19 | 19 | |||
HBA port a | 1 | 26 | 50 | 14 | 24 | 26 | |||
HBA port b | 2 | 26 | 50 | 14 | 24 | 26 | |||
HBA port c | 1 | 27 | 51 | 15 | 25 | 27 | |||
HBA port d | 2 | 27 | 51 | 15 | 25 | 27 | |||
controller_x_4 | FC-VI port a | 1 | 28 | 52 | 16 | 22 | 22 | ||
FC-VI port b | 2 | 28 | 52 | 16 | 22 | 22 | |||
FC-VI port c | 1 | 29 | 53 | 17 | 23 | 23 | |||
FC-VI port d | 2 | 29 | 53 | 17 | 23 | 23 | |||
HBA port a | 1 | 30 | 54 | 18 | 28 | 30 | |||
HBA port b | 2 | 30 | 54 | 18 | 28 | 30 | |||
HBA port c | 1 | 31 | 55 | 19 | 29 | 31 | |||
HBA port d | 2 | 31 | 55 | 19 | 29 | 31 | |||
Stack 1 | bridge_x_51a | FC1 | 1 | 32 | 56 | 20 | 26 | 32 | |
FC2 | 2 | 32 | 56 | 20 | 26 | 32 | |||
bridge_x_51b | FC1 | 1 | 33 | 57 | 21 | 27 | 33 | ||
FC2 | 2 | 33 | 57 | 21 | 27 | 33 | |||
Stack 2 | bridge_x_52a | FC1 | 1 | 34 | 58 | 22 | 30 | 34 | |
FC2 | 2 | 34 | 58 | 22 | 30 | 34 | |||
bridge_x_52b | FC1 | 1 | 35 | 59 | 23 | 31 | 35 | ||
FC2 | 2 | 35 | 59 | 23 | 31 | 35 | |||
Stack 3 | bridge_x_53a | FC1 | 1 | 36 | 60 | - | 32 | 36 | |
FC2 | 2 | 36 | 60 | - | 32 | 36 | |||
bridge_x_53b | FC1 | 1 | 37 | 61 | - | 33 | 37 | ||
FC2 | 2 | 37 | 61 | - | 33 | 37 | |||
Stack y | bridge_x_5ya | FC1 | 1 | 38 | 62 | - | 34 | 38 | |
FC2 | 2 | 38 | 62 | - | 34 | 38 | |||
bridge_x_5yb | FC1 | 1 | 39 | 63 | - | 35 | 39 | ||
FC2 | 2 | 39 | 63 | - | 35 | 39 | |||
Note: Additional bridges can be cabled to ports 36 to 39 in G620, G630, G620-1, and G630-1 switches.
|
The following table shows ISL port usage for the Brocade switches.
Switch model | ISL port | Switch port |
---|---|---|
Brocade 6520 | ISL port 1 | 23 |
ISL port 2 | 47 | |
ISL port 3 | 71 | |
ISL port 4 | 95 | |
Brocade 6505 | ISL port 1 | 20 |
ISL port 2 | 21 | |
ISL port 3 | 22 | |
ISL port 4 | 23 | |
Brocade 6510 and Brocade DCX 8510-8 | ISL port 1 | 40 |
ISL port 2 | 41 | |
ISL port 3 | 42 | |
ISL port 4 | 43 | |
ISL port 5 | 44 | |
ISL port 6 | 45 | |
ISL port 7 | 46 | |
ISL port 8 | 47 | |
Brocade 7810 | ISL port 1 | ge2 (10-Gbps) |
ISL port 2 | ge3(10-Gbps) | |
ISL port 3 | ge4 (10-Gbps) | |
ISL port 4 | ge5 (10-Gbps) | |
ISL port 5 | ge6 (10-Gbps) | |
ISL port 6 | ge7 (10-Gbps) | |
Brocade 7840 Note: The Brocade 7840 switch supports either two 40 Gbps VE-ports or up to four 10 Gbps VE-ports per switch for the creation of FCIP ISLs.
|
ISL port 1 | ge0 (40-Gbps) or ge2 (10-Gbps) |
ISL port 2 | ge1 (40-Gbps) or ge3 (10-Gbps) | |
ISL port 3 | ge10 (10-Gbps) | |
ISL port 4 | ge11 (10-Gbps) | |
Brocade G610 | ISL port 1 | 20 |
ISL port 2 | 21 | |
ISL port 3 | 22 | |
ISL port 4 | 23 | |
Brocade G620, G620-1, G630, G630-1, G720 | ISL port 1 | 40 |
ISL port 2 | 41 | |
ISL port 3 | 42 | |
ISL port 4 | 43 | |
ISL port 5 | 44 | |
ISL port 6 | 45 | |
ISL port 7 | 46 | |
ISL port 8 | 47 |
The tables show the maximum supported configuration, with eight controller modules in two DR groups. For smaller configurations, ignore the rows for the additional controller modules.
Cisco 9396S | |||
---|---|---|---|
Component | Port | Switch 1 | Switch 2 |
controller_x_1 | FC-VI port a | 1 | - |
FC-VI port b | - | 1 | |
FC-VI port c | 2 | - | |
FC-VI port d | - | 2 | |
HBA port a | 3 | - | |
HBA port b | - | 3 | |
HBA port c | 4 | - | |
HBA port d | - | 4 | |
controller_x_2 | FC-VI port a | 5 | - |
FC-VI port b | - | 5 | |
FC-VI port c | 6 | - | |
FC-VI port d | - | 6 | |
HBA port a | 7 | - | |
HBA port b | - | 7 | |
HBA port c | 8 | - | |
HBA port d | - | 8 | |
controller_x_3 | FC-VI port a | 49 | |
FC-VI port b | - | 49 | |
FC-VI port c | 50 | ||
FC-VI port d | - | 50 | |
HBA port a | 51 | ||
HBA port b | - | 51 | |
HBA port c | 52 | ||
HBA port d | - | 52 | |
controller_x_4 | FC-VI port a | 53 | - |
FC-VI port b | - | 53 | |
FC-VI port c | 54 | - | |
FC-VI port d | - | 54 | |
HBA port a | 55 | - | |
HBA port b | - | 55 | |
HBA port c | 56 | - | |
HBA port d | - | 56 |
Cisco 9148S | |||
---|---|---|---|
Component | Port | Switch 1 | Switch 2 |
controller_x_1 | FC-VI port a | 1 | - |
FC-VI port b | - | 1 | |
FC-VI port c | 2 | - | |
FC-VI port d | - | 2 | |
HBA port a | 3 | - | |
HBA port b | - | 3 | |
HBA port c | 4 | - | |
HBA port d | - | 4 | |
controller_x_2 | FC-VI port a | 5 | - |
FC-VI port b | - | 5 | |
FC-VI port c | 6 | - | |
FC-VI port d | - | 6 | |
HBA port a | 7 | - | |
HBA port b | - | 7 | |
HBA port c | 8 | - | |
HBA port d | - | 8 | |
controller_x_3 | FC-VI port a | 25 | |
FC-VI port b | - | 25 | |
FC-VI port c | 26 | - | |
FC-VI port d | - | 26 | |
HBA port a | 27 | - | |
HBA port b | - | 27 | |
HBA port c | 28 | - | |
HBA port d | - | 28 | |
controller_x_4 | FC-VI port a | 29 | - |
FC-VI port b | - | 29 | |
FC-VI port c | 30 | - | |
FC-VI port d | - | 30 | |
HBA port a | 31 | - | |
HBA port b | - | 31 | |
HBA port c | 32 | - | |
HBA port d | - | 32 |
Cisco 9132T | |||
---|---|---|---|
MDS module 1 | |||
Component | Port | Switch 1 | Switch 2 |
controller_x_1 | FC-VI port a | 1 | - |
FC-VI port b | - | 1 | |
FC-VI port c | 2 | - | |
FC-VI port d | - | 2 | |
HBA port a | 3 | - | |
HBA port b | - | 3 | |
HBA port c | 4 | - | |
HBA port d | - | 4 | |
controller_x_2 | FC-VI port a | 5 | - |
FC-VI port b | - | 5 | |
FC-VI port c | 6 | - | |
FC-VI port d | - | 6 | |
HBA port a | 7 | - | |
HBA port b | - | 7 | |
HBA port c | 8 | - | |
HBA port d | - | 8 | |
MDS module 2 | |||
Component | Port | Switch 1 | Switch 2 |
controller_x_3 | FC-VI port a | 1 | - |
FC-VI port b | - | 1 | |
FC-VI port c | 2 | - | |
FC-VI port d | - | 2 | |
HBA port a | 3 | - | |
HBA port b | - | 3 | |
HBA port c | 4 | - | |
HBA port d | - | 4 | |
controller_x_4 | FC-VI port a | 5 | - |
FC-VI port b | - | 5 | |
FC-VI port c | 6 | - | |
FC-VI port d | - | 6 | |
HBA port a | 7 | - | |
HBA port b | - | 7 | |
HBA port c | 8 | - | |
HBA port d | - | 8 |
Cisco 9250i* | |||
---|---|---|---|
Component | Port | Switch 1 | Switch 2 |
controller_x_1 | FC-VI port a | 1 | - |
FC-VI port b | - | 1 | |
HBA port a | 2 | - | |
HBA port b | - | 2 | |
HBA port c | 3 | - | |
HBA port d | - | 3 | |
controller_x_2 | FC-VI port a | 4 | - |
FC-VI port b | - | 4 | |
HBA port a | 5 | - | |
HBA port b | - | 5 | |
HBA port c | 6 | - | |
HBA port d | - | 6 | |
controller_x_3 | FC-VI port a | 7 | - |
FC-VI port b | - | 7 | |
HBA port a | 8 | - | |
HBA port b | - | 8 | |
HBA port c | 9 | - | |
HBA port d | - | 9 | |
controller_x_4 | FC-VI port a | 10 | - |
FC-VI port b | - | 10 | |
HBA port a | 11 | - | |
HBA port b | - | 11 | |
HBA port c | 13 | - | |
HBA port d | - | 13 |
* - The Cisco 9250i switch is not supported for eight-node MetroCluster configurations.
Cisco 9396S | |||
---|---|---|---|
FibreBridge 7500 using two FC ports | Port | Switch 1 | Switch 2 |
bridge_x_1a | FC1 | 9 | - |
FC2 | - | 9 | |
bridge_x_1b | FC1 | 10 | - |
FC2 | - | 10 | |
bridge_x_2a | FC1 | 11 | - |
FC2 | - | 11 | |
bridge_x_2b | FC1 | 12 | - |
FC2 | - | 12 | |
bridge_x_3a | FC1 | 13 | - |
FC2 | - | 13 | |
bridge_x_3b | FC1 | 14 | - |
FC2 | - | 14 | |
bridge_x_4a | FC1 | 15 | - |
FC2 | - | 15 | |
bridge_x_4b | FC1 | 16 | - |
FC2 | - | 16 | |
Additional bridges can be attached using ports 17 through 40 and 57 through 88 following the same pattern. |
Cisco 9148S | |||
---|---|---|---|
FibreBridge 7500 using two FC ports | Port | ||
Switch 1 | Switch 2 | ||
bridge_x_1a | FC1 | 9 | - |
FC2 | - | 9 | |
bridge_x_1b | FC1 | 10 | - |
FC2 | - | 10 | |
bridge_x_2a | FC1 | 11 | - |
FC2 | - | 11 | |
bridge_x_2b | FC1 | 12 | - |
FC2 | - | 12 | |
bridge_x_3a | FC1 | 13 | - |
FC2 | - | 13 | |
bridge_x_3b | FC1 | 14 | - |
FC2 | - | 14 | |
bridge_x_4a | FC1 | 15 | - |
FC2 | - | 15 | |
bridge_x_4b | FC1 | 16 | - |
FC2 | - | 16 | |
Additional bridges for a second DR group or second MetroCluster configuration can be attached using ports 33 through 40 following the same pattern. |
Cisco 9132T | |||
---|---|---|---|
FibreBridge 7500 using two FC ports | Port | ||
Switch 1 | Switch 2 | ||
bridge_x_1a | FC1 | 9 | - |
FC2 | - | 9 | |
bridge_x_1b | FC1 | 10 | - |
FC2 | - | 10 | |
bridge_x_2a | FC1 | 11 | - |
FC2 | - | 11 | |
bridge_x_2b | FC1 | 12 | - |
FC2 | - | 12 | |
Additional bridges for a second DR group or second MetroCluster configuration can be attached using the same port numbers on the second MDS module. |
Cisco 9250i | |||
---|---|---|---|
FibreBridge 7500 using two FC ports | Port | ||
Switch 1 | Switch 2 | ||
bridge_x_1a | FC1 | 14 | - |
FC2 | - | 14 | |
bridge_x_1b | FC1 | 15 | - |
FC2 | - | 15 | |
bridge_x_2a | FC1 | 17 | - |
FC2 | - | 17 | |
bridge_x_2b | FC1 | 18 | - |
FC2 | - | 18 | |
bridge_x_3a | FC1 | 19 | - |
FC2 | - | 19 | |
bridge_x_3b | FC1 | 21 | - |
FC2 | - | 21 | |
bridge_x_4a | FC1 | 22 | - |
FC2 | - | 22 | |
bridge_x_4b | FC1 | 23 | - |
FC2 | - | 23 | |
Additional bridges for a second DR group or second MetroCluster configuration can be attached using ports 25 through 48 following the same pattern. |
The following tables show bridge port usage when using FibreBridge 6500 bridges or FibreBridge 7500 bridges using one FC port (FC1 or FC2) only. For FibreBridge 7500 bridges using one FC port, either FC1 or FC2 can be cabled to the port indicated as FC1. Additional bridges can be attached using ports 25-48.
FibreBridge 6500 bridge or FibreBridge 7500 using one FC port | Port | Cisco 9396S | |
---|---|---|---|
Switch 1 | Switch 2 | ||
bridge_x_1a | FC1 | 9 | - |
bridge_x_1b | FC1 | - | 9 |
bridge_x_2a | FC1 | 10 | - |
bridge_x_2b | FC1 | - | 10 |
bridge_x_3a | FC1 | 11 | - |
bridge_x_3b | FC1 | - | 11 |
bridge_x_4a | FC1 | 12 | - |
bridge_x_4b | FC1 | - | 12 |
bridge_x_5a | FC1 | 13 | - |
bridge_x_5b | FC1 | - | 13 |
bridge_x_6a | FC1 | 14 | - |
bridge_x_6b | FC1 | - | 14 |
bridge_x_7a | FC1 | 15 | - |
bridge_x_7b | FC1 | - | 15 |
bridge_x_8a | FC1 | 16 | - |
bridge_x_8b | FC1 | - | 16 |
Additional bridges can be attached using ports 17 through 40 and 57 through 88 following the same pattern. |
FibreBridge 6500 bridge or FibreBridge 7500 using one FC port | Port | Cisco 9148S | |
---|---|---|---|
Switch 1 | Switch 2 | ||
bridge_x_1a | FC1 | 9 | - |
bridge_x_1b | FC1 | - | 9 |
bridge_x_2a | FC1 | 10 | - |
bridge_x_2b | FC1 | - | 10 |
bridge_x_3a | FC1 | 11 | - |
bridge_x_3b | FC1 | - | 11 |
bridge_x_4a | FC1 | 12 | - |
bridge_x_4b | FC1 | - | 12 |
bridge_x_5a | FC1 | 13 | - |
bridge_x_5b | FC1 | - | 13 |
bridge_x_6a | FC1 | 14 | - |
bridge_x_6b | FC1 | - | 14 |
bridge_x_7a | FC1 | 15 | - |
bridge_x_7b | FC1 | - | 15 |
bridge_x_8a | FC1 | 16 | - |
bridge_x_8b | FC1 | - | 16 |
Additional bridges for a second DR group or second MetroCluster configuration can be attached using ports 25 through 48 following the same pattern. |
Cisco 9250i | |||
---|---|---|---|
FibreBridge 6500 bridge or FibreBridge 7500 using one FC port | Port | Switch 1 | Switch 2 |
bridge_x_1a | FC1 | 14 | - |
bridge_x_1b | FC1 | - | 14 |
bridge_x_2a | FC1 | 15 | - |
bridge_x_2b | FC1 | - | 15 |
bridge_x_3a | FC1 | 17 | - |
bridge_x_3b | FC1 | - | 17 |
bridge_x_4a | FC1 | 18 | - |
bridge_x_4b | FC1 | - | 18 |
bridge_x_5a | FC1 | 19 | - |
bridge_x_5b | FC1 | - | 19 |
bridge_x_6a | FC1 | 21 | - |
bridge_x_6b | FC1 | - | 21 |
bridge_x_7a | FC1 | 22 | - |
bridge_x_7b | FC1 | - | 22 |
bridge_x_8a | FC1 | 23 | - |
bridge_x_8b | FC1 | - | 23 |
Additional bridges can be attached using ports 25 through 48 following the same pattern. |
The following table shows ISL port usage. ISL port usage is the same on all switches in the configuration.
Switch model | ISL port | Switch port |
---|---|---|
Cisco 9396S | ISL 1 | 44 |
ISL 2 | 48 | |
ISL 3 | 92 | |
ISL 4 | 96 | |
Cisco 9250i with 24 port license | ISL 1 | 12 |
ISL 2 | 16 | |
ISL 3 | 20 | |
ISL 4 | 24 | |
Cisco 9148S | ISL 1 | 20 |
ISL 2 | 24 | |
ISL 3 | 44 | |
ISL 4 | 48 | |
Cisco 9132T | ISL 1 | MDS module 1 port 13 |
ISL 2 | MDS module 1 port 14 | |
ISL 3 | MDS module 1 port 15 | |
ISL 4 | MDS module 1 port 16 |