Port assignments for FC switches when using ONTAP 9.1 or later

Contributors netapp-martyh netapp-thomi netapp-ivanad Download PDF of this page

You need to verify that you are using the specified port assignments when you cable the FC switches when using ONTAP 9.1 and later.

Ports that are not used for attaching initiator ports, FC-VI ports, or ISLs can be reconfigured to act as storage ports. However, if the supported RCFs are being used, the zoning must be changed accordingly.

If the supported RCFs are used, ISL ports might not connect to the same ports shown and might need to be reconfigured manually.

If you configured your switches using the port assignments for ONTAP 9, you can continue to use the older assignments. However, new configurations running ONTAP 9.1 or later releases should use the port assignments shown here.

Overall cabling guidelines

You should be aware of the following guidelines when using the cabling tables:

  • The Brocade and Cisco switches use different port numbering:

    • On Brocade switches, the first port is numbered 0.

    • On Cisco switches, the first port is numbered 1.

  • The cabling is the same for each FC switch in the switch fabric.

  • AFF A300 and FAS8200 storage systems can be ordered with one of two options for FC-VI connectivity:

    • Onboard ports 0e and 0f configured in FC-VI mode.

    • Ports 1a and 1b on an FC-VI card in slot 1.

  • AFF A700 and FAS9000 storage systems require four FC-VI ports. The following tables show cabling for the FC switches with four FC-VI ports on each controller except for the Cisco 9250i switch.

    For other storage systems, use the cabling shown in the tables but ignore the cabling for FC-VI ports c and d.

    You can leave those ports empty.

  • AFF A400 and FAS8300 storage systems use ports 2a and 2b for FC-VI connectivity.

  • If you have two MetroCluster configurations sharing ISLs, use the same port assignments as that for an eight-node MetroCluster cabling.

    The number of ISLs you cable may vary depending on site’s requirements.

    See the section on ISL considerations.

Brocade port usage for controllers in a MetroCluster configuration running ONTAP 9.1 or later

The following tables show port usage on Brocade switches. The tables show the maximum supported configuration, with eight controller modules in two DR groups. For smaller configurations, ignore the rows for the additional controller modules. Note that eight ISLs are supported only on the Brocade 6510, Brocade DCX 8510-8, G620, G630, G620-1, G630-1, and G720 switches.

Note
  • Port usage for the Brocade 6505 and Brocade G610 switches in an eight-node MetroCluster configuration is not shown. Due to the limited number of ports, port assignments must be made on a site-by-site basis depending on the controller module model and the number of ISLs and bridge pairs in use.

  • The Brocade DCX 8510-8 switch can use the same port layout as the 6510 switch or the 7840 switch.

Configurations using FibreBridge 6500N bridges or FibreBridge 7500N or 7600N using one FC port (FC1 or FC2) only

MetroCluster 1 or DR Group 1

Component

Port

Brocade switch models 6505, 6510, 6520, 7810, 7840, G610, G620, G620-1, G630, G630-1 and DCX 8510-8

Brocade switch model G720

Connects to FC switch…​

Connects to switch port…​

Connects to switch port…​

controller_x_1

FC-VI port a

1

0

0

FC-VI port b

2

0

0

FC-VI port c

1

1

1

FC-VI port d

2

1

1

HBA port a

1

2

8

HBA port b

2

2

8

HBA port c

1

3

9

HBA port d

2

3

9

controller_x_2

FC-VI port a

1

4

4

FC-VI port b

2

4

4

FC-VI port c

1

5

5

FC-VI port d

2

5

5

HBA port a

1

6

12

HBA port b

2

6

12

HBA port c

1

7

13

HBA port d

2

7

13

Configurations using FibreBridge 6500N bridges or FibreBridge 7500N or 7600N using one FC port (FC1 or FC2) only

MetroCluster 1 or DR Group 1

Component

Port

Brocade switch models 6505, 6510, 6520, 7810, 7840, G610, G620, G620-1, G630, G630-1 and DCX 8510-8

Brocade switch model G720

Connects to FC switch…​

Connects to switch port…​

Connects to switch port…​

Stack 1

bridge_x_1a

1

8

10

bridge_x_1b

2

8

10

Stack 2

bridge_x_2a

1

9

11

bridge_x_2b

2

9

11

Stack 3

bridge_x_3a

1

10

14

bridge_x_4b

2

10

14

Stack y

bridge_x_ya

1

11

15

bridge_x_yb

2

11

15

Note
  • On G620, G630, G620-1 and G630-1 switches, additional bridges can be cabled to ports 12 - 17, 20 and 21.

  • On G610 switches, additional bridges can be cabled to ports 12 - 19.

  • On G720 switches, additional bridges can be cabled to ports 16 - 17, 20 and 21.

Configurations using FibreBridge 6500N bridges or FibreBridge 7500N or 7600N using one FC port (FC1 or FC2) only

MetroCluster 2 or DR Group 2

Brocade switch model

Component

Port

Connects to FC_switch…​

6510, DCX 8510-8

6520

7840, DCX 8510-8

G620, G620-1, G630, G630-1

G720

controller_x_3

FC-VI port a

1

24

48

12

18

18

FC-VI port b

2

24

48

12

18

18

FC-VI port c

1

25

49

13

19

19

FC-VI port d

2

25

49

13

19

19

HBA port a

1

26

50

14

24

26

HBA port b

2

26

50

14

24

26

HBA port c

1

27

51

15

25

27

HBA port d

2

27

51

15

25

27

controller_x_4

FC-VI port a

1

28

52

16

22

22

FC-VI port b

2

28

52

16

22

22

FC-VI port c

1

29

53

17

23

23

FC-VI port d

2

29

53

17

23

23

HBA port a

1

30

54

18

28

30

HBA port b

2

30

54

18

28

30

HBA port c

1

31

55

19

29

31

HBA port d

2

32

55

19

29

31

Stack 1

bridge_x_51a

1

32

56

20

26

32

bridge_x_51b

2

32

56

20

26

32

Stack 2

bridge_x_52a

1

33

57

21

27

33

bridge_x_52b

2

33

57

21

27

33

Stack 3

bridge_x_53a

1

34

58

22

30

34

bridge_x_54b

2

34

58

22

30

34

Stack y

bridge_x_ya

1

35

59

23

31

35

bridge_x_yb

2

35

59

23

31

35

Note
  • On G720 switches, additional bridges can be cabled to ports 36-39.

Configurations using FibreBridge 7500N or 7600N using both FC ports (FC1 and FC2)

MetroCluster 1 or DR Group 1

Component

Port

Brocade switch models 6505, 6510, 6520, 7810, 7840, G610, G620, G620-1, G630, G630-1, and DCX 8510-8

Brocade switch G720

Connects to FC_switch…​

Connects to switch port…​

Connects to switch port…​

Stack 1

bridge_x_1a

FC1

1

8

10

FC2

2

8

10

bridge_x_1B

FC1

1

9

11

FC2

2

9

11

Stack 2

bridge_x_2a

FC1

1

10

14

FC2

2

10

14

bridge_x_2B

FC1

1

11

15

FC2

2

11

15

Stack 3

bridge_x_3a

FC1

1

12*

16

FC2

2

12*

16

bridge_x_3B

FC1

1

13*

17

FC2

2

13*

17

Stack y

bridge_x_ya

FC1

1

14*

20

FC2

2

14*

20

bridge_x_yb

FC1

1

15*

21

FC2

2

15*

21

* Ports 12 through 15 are reserved for the second MetroCluster or DR group on the Brocade 7840 switch.

Note Additional bridges can be cabled to ports 16, 17, 20 and 21 in G620, G630, G620-1 and G630-1 switches.

Configurations using FibreBridge 7500N or 7600N using both FC ports (FC1 and FC2)

MetroCluster 2 or DR Group 2

Component

Port

Brocade switch model

Connects to FC_switch…​

6510, DCX 8510-8

6520

7840, DCX 8510-8

G620, G620-1, G630, G630-1

G720

controller_x_3

FC-VI port a

1

24

48

12

18

18

FC-VI port b

2

24

48

12

18

18

FC-VI port c

1

25

49

13

19

19

FC-VI port d

2

25

49

13

19

19

HBA port a

1

26

50

14

24

26

HBA port b

2

26

50

14

24

26

HBA port c

1

27

51

15

25

27

HBA port d

2

27

51

15

25

27

controller_x_4

FC-VI port a

1

28

52

16

22

22

FC-VI port b

2

28

52

16

22

22

FC-VI port c

1

29

53

17

23

23

FC-VI port d

2

29

53

17

23

23

HBA port a

1

30

54

18

28

30

HBA port b

2

30

54

18

28

30

HBA port c

1

31

55

19

29

31

HBA port d

2

31

55

19

29

31

Stack 1

bridge_x_51a

FC1

1

32

56

20

26

32

FC2

2

32

56

20

26

32

bridge_x_51b

FC1

1

33

57

21

27

33

FC2

2

33

57

21

27

33

Stack 2

bridge_x_52a

FC1

1

34

58

22

30

34

FC2

2

34

58

22

30

34

bridge_x_52b

FC1

1

35

59

23

31

35

FC2

2

35

59

23

31

35

Stack 3

bridge_x_53a

FC1

1

36

60

-

32

36

FC2

2

36

60

-

32

36

bridge_x_53b

FC1

1

37

61

-

33

37

FC2

2

37

61

-

33

37

Stack y

bridge_x_5ya

FC1

1

38

62

-

34

38

FC2

2

38

62

-

34

38

bridge_x_5yb

FC1

1

39

63

-

35

39

FC2

2

39

63

-

35

39

Note Additional bridges can be cabled to ports 36 to 39 in G620, G630, G620-1, and G630-1 switches.

Brocade port usage for ISLs in a MetroCluster configuration running ONTAP 9.1 or later

The following table shows ISL port usage for the Brocade switches.

Note AFF A700 or FAS9000 systems support up to eight ISLs for improved performance. Eight ISLs are supported on the Brocade 6510 and G620 switches.
Switch model ISL port Switch port

Brocade 6520

ISL port 1

23

ISL port 2

47

ISL port 3

71

ISL port 4

95

Brocade 6505

ISL port 1

20

ISL port 2

21

ISL port 3

22

ISL port 4

23

Brocade 6510 and Brocade DCX 8510-8

ISL port 1

40

ISL port 2

41

ISL port 3

42

ISL port 4

43

ISL port 5

44

ISL port 6

45

ISL port 7

46

ISL port 8

47

Brocade 7810

ISL port 1

ge2 (10-Gbps)

ISL port 2

ge3(10-Gbps)

ISL port 3

ge4 (10-Gbps)

ISL port 4

ge5 (10-Gbps)

ISL port 5

ge6 (10-Gbps)

ISL port 6

ge7 (10-Gbps)

Brocade 7840

Note: The Brocade 7840 switch supports either two 40 Gbps VE-ports or up to four 10 Gbps VE-ports per switch for the creation of FCIP ISLs.

ISL port 1

ge0 (40-Gbps) or ge2 (10-Gbps)

ISL port 2

ge1 (40-Gbps) or ge3 (10-Gbps)

ISL port 3

ge10 (10-Gbps)

ISL port 4

ge11 (10-Gbps)

Brocade G610

ISL port 1

20

ISL port 2

21

ISL port 3

22

ISL port 4

23

Brocade G620, G620-1, G630, G630-1, G720

ISL port 1

40

ISL port 2

41

ISL port 3

42

ISL port 4

43

ISL port 5

44

ISL port 6

45

ISL port 7

46

ISL port 8

47

Cisco port usage for controllers in a MetroCluster configuration running ONTAP 9.4 or later

The tables show the maximum supported configurations, with eight controller modules in two DR groups. For smaller configurations, ignore the rows for the additional controller modules.

Cisco 9396S

Component

Port

Switch 1

Switch 2

controller_x_1

FC-VI port a

1

-

FC-VI port b

-

1

FC-VI port c

2

-

FC-VI port d

-

2

HBA port a

3

-

HBA port b

-

3

HBA port c

4

-

HBA port d

-

4

controller_x_2

FC-VI port a

5

-

FC-VI port b

-

5

FC-VI port c

6

-

FC-VI port d

-

6

HBA port a

7

-

HBA port b

-

7

HBA port c

8

HBA port d

-

8

controller_x_3

FC-VI port a

49

FC-VI port b

-

49

FC-VI port c

50

-

FC-VI port d

-

50

HBA port a

51

-

HBA port b

-

51

HBA port c

52

HBA port d

-

52

controller_x_4

FC-VI port a

53

-

FC-VI port b

-

53

FC-VI port c

54

-

FC-VI port d

-

54

HBA port a

55

-

HBA port b

-

55

HBA port c

56

-

HBA port d

-

56

Cisco 9148S

Component

Port

Switch 1

Switch 2

controller_x_1

FC-VI port a

1

FC-VI port b

-

1

FC-VI port c

2

-

FC-VI port d

-

2

HBA port a

3

-

HBA port b

-

3

HBA port c

4

-

HBA port d

-

4

controller_x_2

FC-VI port a

5

-

FC-VI port b

-

5

FC-VI port c

6

-

FC-VI port d

-

6

HBA port a

7

-

HBA port b

-

7

HBA port c

8

-

HBA port d

-

8

controller_x_3

FC-VI port a

25

FC-VI port b

-

25

FC-VI port c

26

-

FC-VI port d

-

26

HBA port a

27

-

HBA port b

-

27

HBA port c

28

-

HBA port d

-

28

controller_x_4

FC-VI port a

29

-

FC-VI port b

-

29

FC-VI port c

30

-

FC-VI port d

-

30

HBA port a

31

-

HBA port b

-

31

HBA port c

32

-

HBA port d

-

32

Cisco 9132T

MDS module 1

Component

Port

Switch 1

Switch 2

controller_x_1

FC-VI port a

1

-

FC-VI port b

-

1

FC-VI port c

2

-

FC-VI port d

-

2

HBA port a

3

-

HBA port b

-

3

HBA port c

4

-

HBA port d

-

4

controller_x_2

FC-VI port a

5

-

FC-VI port b

-

5

FC-VI port c

6

-

FC-VI port d

-

6

HBA port a

7

-

HBA port b

-

7

HBA port c

8

-

HBA port d

-

8

MDS module 2

Component

Port

Switch 1

Switch 2

controller_x_3

FC-VI port a

1

-

FC-VI port b

-

1

FC-VI port c

2

-

FC-VI port d

-

2

HBA port a

3

-

HBA port b

-

3

HBA port c

4

-

HBA port d

-

4

controller_x_4

FC-VI port a

5

-

FC-VI port b

-

5

FC-VI port c

6

-

FC-VI port d

-

6

HBA port a

7

-

HBA port b

-

7

HBA port c

8

-

HBA port d

-

8

Note The following table shows systems with two FC-VI ports. AFF A700 and FAS9000 systems have four FC-VI ports (a, b, c, and d). If using an AFF A700 or FAS9000 system, the port assignments move along by one position. For example, FC-VI ports c and d go to switch port 2 and HBA ports a and b go to switch port 3.

Cisco 9250i

Note: The Cisco 9250i switch is not supported for eight-node MetroCluster configurations.

Component

Port

Switch 1

Switch 2

controller_x_1

FC-VI port a

1

-

FC-VI port b

-

1

HBA port a

2

-

HBA port b

-

2

HBA port c

3

-

HBA port d

-

3

controller_x_2

FC-VI port a

4

-

FC-VI port b

-

4

HBA port a

5

-

HBA port b

-

5

HBA port c

6

-

HBA port d

-

6

controller_x_3

FC-VI port a

7

-

FC-VI port b

-

7

HBA port a

8

-

HBA port b

-

8

HBA port c

9

-

HBA port d

-

9

controller_x_4

FC-VI port a

10

-

FC-VI port b

-

10

HBA port a

11

-

HBA port b

-

11

HBA port c

13

-

HBA port d

-

13

Cisco port usage for FC-to-SAS bridges in a MetroCluster configuration running ONTAP 9.1 or later

Cisco 9396S

FibreBridge 7500 using two FC ports

Port

Switch 1

Switch 2

bridge_x_1a

FC1

9

-

FC2

-

9

bridge_x_1b

FC1

10

-

FC2

-

10

bridge_x_2a

FC1

11

-

FC2

-

11

bridge_x_2b

FC1

12

-

FC2

-

12

bridge_x_3a

FC1

13

-

FC2

-

13

bridge_x_3b

FC1

14

-

FC2

-

14

bridge_x_4a

FC1

15

-

FC2

-

15

bridge_x_4b

FC1

16

-

FC2

-

16

Additional bridges can be attached using ports 17 through 40 and 57 through 88 following the same pattern.

Cisco 9148S

FibreBridge 7500 using two FC ports

Port

Switch 1

Switch 2

bridge_x_1a

FC1

9

-

FC2

-

9

bridge_x_1b

FC1

10

-

FC2

-

10

bridge_x_2a

FC1

11

-

FC2

-

11

bridge_x_2b

FC1

12

-

FC2

-

12

bridge_x_3a

FC1

13

-

FC2

-

13

bridge_x_3b

FC1

14

-

FC2

-

14

bridge_x_4a

FC1

15

-

FC2

-

15

bridge_x_4b

FC1

16

-

FC2

-

16

Additional bridges for a second DR group or second MetroCluster configuration can be attached using ports 33 through 40 following the same pattern.

Cisco 9132T

FibreBridge 7500 using two FC ports

Port

Switch

Switch 2

bridge_x_1a

FC1

9

-

FC2

-

9

bridge_x_1b

FC1

10

-

FC2

-

10

bridge_x_2a

FC1

11

-

FC2

-

11

bridge_x_2b

FC1

12

-

FC2

-

12

Additional bridges for a second DR group or second MetroCluster configuration can be attached using the same port numbers on the second MDS module.

Cisco 9250i

FibreBridge 7500 using two FC ports

Port

Switch 1

Switch 2

bridge_x_1a

FC1

14

-

FC2

-

14

bridge_x_1b

FC1

15

-

FC2

-

15

bridge_x_2a

FC1

17

-

FC2

-

17

bridge_x_2b

FC1

18

-

FC2

-

18

bridge_x_3a

FC1

19

-

FC2

-

19

bridge_x_3b

FC1

21

-

FC2

-

21

bridge_x_4a

FC1

22

-

FC2

-

22

bridge_x_4b

FC1

23

-

FC2

-

23

Additional bridges for a second DR group or second MetroCluster configuration can be attached using ports 25 through 48 following the same pattern.

The following tables show bridge port usage when using FibreBridge 6500 bridges or FibreBridge 7500 bridges using one FC port (FC1 or FC2) only. For FibreBridge 7500 bridges using one FC port, either FC1 or FC2 can be cabled to the port indicated as FC1. Additional bridges can be attached using ports 25-48.

FibreBridge 6500 bridges or FibreBridge 7500 bridges using one FC port

FibreBridge 6500 bridge or FibreBridge 7500 using one FC port

Port

Cisco 9396S

Switch 1

Switch 2

bridge_x_1a

FC1

9

-

bridge_x_1b

FC1

-

9

bridge_x_2a

FC1

10

-

bridge_x_2b

FC1

-

10

bridge_x_3a

FC1

11

-

bridge_x_3b

FC1

-

11

bridge_x_4a

FC1

12

-

bridge_x_4b

FC1

-

12

bridge_x_5a

FC1

13

-

bridge_x_5b

FC1

-

13

bridge_x_6a

FC1

14

-

bridge_x_6b

FC1

-

14

bridge_x_7a

FC1

15

-

bridge_x_7b

FC1

-

15

bridge_x_8a

FC1

16

-

bridge_x_8b

FC1

-

16

Additional bridges can be attached using ports 17 through 40 and 57 through 88 following the same pattern.

FibreBridge 6500 bridges or FibreBridge 7500 bridges using one FC port

Bridge

Port

Cisco 9148S

Switch 1

Switch 2

bridge_x_1a

FC1

9

-

bridge_x_1b

FC1

-

9

bridge_x_2a

FC1

10

-

bridge_x_2b

FC1

-

10

bridge_x_3a

FC1

11

-

bridge_x_3b

FC1

-

11

bridge_x_4a

FC1

12

-

bridge_x_4b

FC1

-

12

bridge_x_5a

FC1

13

-

bridge_x_5b

FC1

-

13

bridge_x_6a

FC1

14

-

bridge_x_6b

FC1

-

14

bridge_x_7a

FC1

15

-

bridge_x_7b

FC1

-

15

bridge_x_8a

FC1

16

-

bridge_x_8b

FC1

-

16

Additional bridges for a second DR group or second MetroCluster configuration can be attached using ports 25 through 48 following the same pattern.

Cisco 9250i

FibreBridge 6500 bridge or FibreBridge 7500 using one FC port

Port

Switch 1

Switch 2

bridge_x_1a

FC1

14

-

bridge_x_1b

FC1

-

14

bridge_x_2a

FC1

15

-

bridge_x_2b

FC1

-

15

bridge_x_3a

FC1

17

-

bridge_x_3b

FC1

-

17

bridge_x_4a

FC1

18

-

bridge_x_4b

FC1

-

18

bridge_x_5a

FC1

19

-

bridge_x_5b

FC1

-

19

bridge_x_6a

FC1

21

-

bridge_x_6b

FC1

-

21

bridge_x_7a

FC1

22

-

bridge_x_7b

FC1

-

22

bridge_x_8a

FC1

23

-

bridge_x_8b

FC1

-

23

Additional bridges can be attached using ports 25 through 48 following the same pattern.

Cisco port usage for ISLs in an eight-node configuration in a MetroCluster configuration running ONTAP 9.1 or later

The following table shows ISL port usage. ISL port usage is the same on all switches in the configuration.

Switch model

ISL port

Switch port

Cisco 9396S

ISL 1

44

ISL 2

48

ISL 3

92

ISL 4

96

Cisco 9250i with 24 port license

ISL 1

12

ISL 2

16

ISL 3

20

ISL 4

24

Cisco 9148S

ISL 1

20

ISL 2

24

ISL 3

44

ISL 4

48

Cisco 9132T

ISL 1

MDS module 1 port 13

ISL 2

MDS module 1 port 14

ISL 3

MDS module 1 port 15

ISL 4

MDS module 1 port 16