Skip to main content

Commands for managing the SP from ONTAP

Contributors netapp-thomi netapp-forry netapp-barbe

ONTAP provides commands for managing the SP, including the SP network configuration, SP firmware image, SSH access to the SP, and general SP administration.

Commands for managing the SP network configuration

If you want to…​ Run this ONTAP command…​

Enable the SP automatic network configuration for the SP to use the IPv4 or IPv6 address family of the specified subnet

system service-processor network auto-configuration enable

Disable the SP automatic network configuration for the IPv4 or IPv6 address family of the subnet specified for the SP

system service-processor network auto-configuration disable

Display the SP automatic network configuration

system service-processor network auto-configuration show

Manually configure the SP network for a node, including the following:

  • The IP address family (IPv4 or IPv6)

  • Whether the network interface of the specified IP address family should be enabled

  • If you are using IPv4, whether to use the network configuration from the DHCP server or the network address that you specify

  • The public IP address for the SP

  • The netmask for the SP (if using IPv4)

  • The network prefix-length of the subnet mask for the SP (if using IPv6)

  • The gateway IP address for the SP

system service-processor network modify

Display the SP network configuration, including the following:

  • The configured address family (IPv4 or IPv6) and whether it is enabled

  • The remote management device type

  • The current SP status and link status

  • Network configuration, such as IP address, MAC address, netmask, prefix-length of subnet mask, router-assigned IP address, link local IP address, and gateway IP address

  • The time the SP was last updated

  • The name of the subnet used for SP automatic configuration

  • Whether the IPv6 router-assigned IP address is enabled

  • SP network setup status

  • Reason for the SP network setup failure

system service-processor network show

Displaying complete SP network details requires the -instance parameter.

Modify the SP API service configuration, including the following:

  • Changing the port used by the SP API service

  • Enabling or disabling the SP API service

system service-processor api-service modify

(advanced privilege level)

Display the SP API service configuration

system service-processor api-service show

(advanced privilege level)

Renew the SSL and SSH certificates used by the SP API service for internal communication

  • For ONTAP 9.5 or later: system service-processor api-service renew-internal-certificates

  • For ONTAP 9.4 or earlier: system service-processor api-service renew-certificates

    (advanced privilege level)

Commands for managing the SP firmware image

If you want to…​ Run this ONTAP command…​

Display the details of the currently installed SP firmware image, including the following:

  • The remote management device type

  • The image (primary or backup) that the SP is booted from, its status, and firmware version

  • Whether the firmware automatic update is enabled and the last update status

system service-processor image show

The -is-current parameter indicates the image (primary or backup) that the SP is currently booted from, not if the installed firmware version is most current.

Enable or disable the SP automatic firmware update

system service-processor image modify

By default, the SP firmware is automatically updated with the update of ONTAP or when a new version of the SP firmware is manually downloaded. Disabling the automatic update is not recommended because doing so can result in suboptimal or nonqualified combinations between the ONTAP image and the SP firmware image.

Manually download an SP firmware image on a node

system node image get

Note

Before you run the system node image commands, you must set the privilege level to advanced (set -privilege advanced), entering y when prompted to continue.

The SP firmware image is packaged with ONTAP. You do not need to download the SP firmware manually, unless you want to use an SP firmware version that is different from the one packaged with ONTAP.

Display the status for the latest SP firmware update triggered from ONTAP, including the following information:

  • The start and end time for the latest SP firmware update

  • Whether an update is in progress and the percentage that is complete

system service-processor image update-progress show

Commands for managing SSH access to the SP

If you want to…​ Run this ONTAP command…​

Grant SP access to only the specified IP addresses

system service-processor ssh add-allowed-addresses

Block the specified IP addresses from accessing the SP

system service-processor ssh remove-allowed-addresses

Display the IP addresses that can access the SP

system service-processor ssh show

Commands for general SP administration

If you want to…​ Run this ONTAP command…​

Display general SP information, including the following:

  • The remote management device type

  • The current SP status

  • Whether the SP network is configured

  • Network information, such as the public IP address and the MAC address

  • The SP firmware version and Intelligent Platform Management Interface (IPMI) version

  • Whether the SP firmware automatic update is enabled

system service-processor show Displaying complete SP information requires the -instance parameter.

Reboot the SP on a node

system service-processor reboot-sp

Generate and send an AutoSupport message that includes the SP log files collected from a specified node

system node autosupport invoke-splog

Display the allocation map of the collected SP log files in the cluster, including the sequence numbers for the SP log files that reside in each collecting node

system service-processor log show-allocations

Related information

ONTAP 9 Commands